[Clinical evaluation of measuring system of occlusal force]

Occlusal status of implant superstructures at mandibular first molar immediately after setting

BACKGROUND

Occlusal contact on the implant superstructures is important for successful treatment. The purpose of this study was to investigate the occlusal contact of single implant superstructures at the mandibular first molar immediately after seating from weak to strong clenching.

METHODS

Subjects were nine patients who had just been fitted with an implant prosthesis in the mandibular first molar region, with no missing teeth other than in the implant region. First, while masseter muscle activity was monitored, maximum clenching strength (100 % maximum voluntary contraction (MVC)) was determined with an electromyogram. Next, occlusal load and occlusal contact area were measured three times at clenching intensities of 40, 60, 80, and 100 % MVC by the use of pressure-sensitive film for occlusal force diagnostic and Occluzer for occlusal force measurement. Finally, the occlusal contact area was measured once each at 20, 40, and 60 % MVC using a silicone testing material and BiteEye for occlusal contact measurement. A two-way analysis of variance (ANOVA) was used to determine occlusal loading and occlusal area as dependent variables, and clenching strength and presence or absence of implant as between-subject factors. A multiple comparison test was performed using the Bonferroni method.

RESULTS

The occlusal contact area and occlusal load of the implant prosthesis increased with clenching strength, and the increases in occlusal contact area and occlusal load of the implant prosthesis were less than those of the contralateral tooth at high clenching strength. However, significant difference was not observed when compared with both sides of the molar region regardless of clenching strength.

CONCLUSIONS

The occlusal contact area of the implant had a tendency to be adjusted smaller than the natural tooth by a dental technician and a dentist. On the other hand, despite the small tissue displaceability of the implant, occlusal load on the implant prosthesis was smaller than on the natural tooth at high clenching strength.

Masticatory efficiency after rehabilitation of acquired maxillary and mandibular defects

The effect of oral cancer with its therapeutic intervention involves significant facial and functional disabilities. It is customary to rehabilitate these patients by surgical or prosthetic means. Studies have been done to assess mastication and other functions after rehabilitation. A review of these studies for assessing masticatory function has been done under separate sections for maxillary and mandibular defects. Different masticatory tests are mentioned. Further scope for research has been highlighted.

Influence of occlusal loading force on occlusal contacts in natural dentition

PURPOSE

Proper occlusal contact is important for the long-term success of prosthodontic therapy. We clarified the effects of occlusal loading force on occlusal contact in natural dentition by comparing measured values for occlusal loading and occlusal contact area.

METHODS

Masseter muscle activity was measured in 10 subjects (2 male, 8 female; mean age, 27 years) with natural dentition using electromyography, with clenching at full strength with nothing interposed between the upper and lower teeth defined as 100% maximum voluntary contraction (MVC). Pressure-sensitive film (Occluzer) was used to examine occlusal contact points at 20, 40, 60, 80, 100 and 120% MVC. A material for checking accuracy of fit (BiteEye) was used to examine occlusal contact points at 20, 40, 60 and 80% MVC. ANOVA and the Bonferroni method were used to assess the results, with the level of significance set at 5%. Coefficients of variation (CV) were also calculated by dividing the standard deviation by the mean.

RESULTS

Occlusal loading and occlusal contact area increased with clenching strength; however, CV showed differences between the methods at low and high MVC.

CONCLUSIONS

With Occluzer, testing should be carried out at clenching strength ≥ 60% MVC. With BiteEye, testing should be carried out from light clenching strength at 20% MVC to moderate clenching strengths at 40-60% MVC. Occluzer and BiteEye (10 μm) gave similar occlusal contact areas at 60-80% MVC. These results suggest that combined use of Occluzer and BiteEye gives an accurate picture of occlusion from weak to strong clenching strength.

APPLICATION OF "PRESCALE" AS AN AID TO CLINICAL DIAGNOSIS IN ORTHODONTICS

We examined the feasibility of applying the Dental Prescale Occluzer System to the evaluation of occlusion in orthodontic patients. The patients were classified according to the type of malocclusion or facial pattern. The values of occlusal contact area and occlusal force obtained from these individuals differed depending on the type of occlusion or facial pattern. These values were higher in individuals with normal occlusion than in patients with malocclusion and higher in patients with the Brachyo facial pattern than in those with the Dolico facial pattern. Because this system can very easily analyze the occlusal contact area, the mean pressure on each occlusal contact point, and the occlusal force during the process of orthodontic treatments, it can be useful as an aid for the initial diagnosis of occlusal problems, the observation of the changes in occlusion during treatment, and the establishment of the final goal of orthodontic treatments.

Bone mineral density in periodontally healthy and edentulous postmenopausal women

(Osteoporosis is the most common metabolic disease among postmenopausal women. Reduced masticatory function caused by tooth loss may be a contributing risk factor of osteoporosis. The present study examined the effect of dentate state on skeletal bone mineral density (BMD) in postmenopausal women. Fourteen periodontally healthy dentate subjects (group H; mean age: 64.0 + 5.5 years) and 12 edentulous subjects (group E; mean age: 67.1 + 2.9 years) were randomly selected from the clinics of the departments of Periodontology and Gerodontology, respectively. Informed consent was obtained from all participants. BMD of the lumbar spine (L2-L4) was measured by dual energy x-ray absorptiometry. In addition, occlusal force was measured in 11 group H subjects and 8 group E subjects by using an occlusal diagnostic system. Risk factors associated with osteoporosis including age, calcium intake, physical activity, and cigarette smoking and causes of tooth loss were assessed by interview and questionnaire sent to all participants. The BMD of group H was 1.07 t 0.21 g/cm2 and that of group E was 0.89 + 0.17 g/cm2, which was significantly different(P< 0.05). The occlusal force of group H and E patients was 312.4 + 148 Nand 56.3 + 36 N, respectively, which was significantly different (P< 0.05). Risk factors such as calcium intake, physical activity, and smoking did not differ significantly between the 2 groups. Thus, the periodontally healthy dentate women, who showed about 6 times higher occlusal force than edentulous women, maintained significantly higher BMD of the lumbar spine than edentulous women. Our results suggest that sufficient masticatory function with periodontally healthy dentition may inhibit or delay the progress of osteoporotic change in skeletal bone or that edentulous women may be more susceptible to osteoporosis.