Multimodal evaluation of tissue-engineered cartilage

Elastomeric Porous Poly(glycerol sebacate) Methacrylate (PGSm) Microspheres as 3D Scaffolds for Chondrocyte Culture and Cartilage Tissue Engineering

Cartilage defects can be difficult to treat; therefore, tissue engineering of cartilage is emerging as a promising potential therapy. One interesting area of research explores the delivery of cells to the cartilage defect via scaffold-based cell delivery vehicles and microsurgery. This study explores the use of novel poly(glycerol sebacate) methacrylate (PGSm)-polymerised high internal phase emulsion (polyHIPE) microspheres as scaffolds with embedded cells for cartilage tissue engineering. Porous microsphere scaffolds (100 µm-1 mm diameter) were produced from emulsions consisting of water and a methacrylate-based photocurable resin of poly(glycerol sebacate). These resins were used in conjunction with a T-junction fluidic device and an ultraviolet (UV) curing lamp to produce porous microspheres with a tuneable size. This technique produced biodegradable PGSm microspheres with similar mechanical properties to cartilage. We further explore these microspheres as scaffolds for three-dimensional culture of chondrocytes. The microspheres proved to be very efficient scaffolds for primary chondrocyte culture and were covered by a dense extracellular matrix (ECM) network during the culture period, creating a tissue disk. The presence of glycosaminoglycans (GAGs) and collagen-II was confirmed, highlighting the utility of the PGSm microspheres as a delivery vehicle for chondrocytes. A number of imaging techniques were utilised to analyse the tissue disk and develop methodologies to characterise the resultant tissue. This study highlights the utility of porous PGSm microspheres for cartilage tissue engineering.

Hydrogel composite mimics biological tissues

A novel composite hydrogel was developed that shows remarkable similarities to load bearing biological tissues. The composite gel consisting of a poly(vinyl alcohol (PVA) matrix filled with poly(acrylic acid) (PAA) microgel particles exhibits osmotic and mechanical properties that are qualitatively different from regular gels. In the PVA/PAA system the swollen PAA particles "inflate" the PVA network. The swelling of the PAA is limited by the tensile stress P_el developing in the PVA matrix. P_el increases with increasing swelling degree, which is opposite to the decrease of the elastic pressure observed in regular gels. The maximum tensile stress Pmaxel can be identified as a quantity that defines the load bearing ability of the composite gel. Systematic osmotic swelling pressure measurements have been made on PVA/PAA gels to determine the effects of PVA stiffness, PAA crosslink density, and Ca²⁺ ion concentration on Pmaxel. It is found that Pmaxel increases with the stiffness of the PVA matrix, and decreases with (i) increasing crosslink density of the PAA and (ii) increasing Ca²⁺ ion concentration. Small angle neutron scattering (SANS) measurements indicate only a weak interaction between the PVA and PAA gels. It is demonstrated that the osmotic swelling pressure of PVA/PAA composite gels reproduces the osmotic behavior of healthy and osteoarthritic cartilage.

Biochemical Aspects of Scaffolds for Cartilage Tissue Engineering; from Basic Science to Regenerative Medicine

Chondral defects are frequent and important causes of pain and disability. Cartilage has limited self-repair and regeneration capacity. The ideal approach for articular cartilage defects is the regeneration of hyaline cartilage with sustainable symptom-free constructs. Tissue engineering provides new strategies for the regeneration of functional cartilage tissue through optimized scaffolds with architectural, mechanical, and biochemical properties similar to the native cartilage tissue. In this review, the basic science of cartilage structure, interactions between proteins, stem cells, as well as biomaterials, scaffold characteristics and fabrication methods, as well as current and potential therapies in regenerative medicine will be discussed mostly from a biochemical point of view. Furthermore, the recent trends in scaffold-based therapies and supplementary factors in cartilage tissue engineering will be considered.

Importance of Osmolarity and Oxygen Tension for Cartilage Tissue Engineering

For cartilage repair in vivo or evaluation of new therapeutic approaches in vitro, the generation of functional cartilage tissue is of crucial importance and can only be achieved if the phenotype of the chondrocytes is preserved. Three-dimensional (3D) cell culture is broadly used for this purpose. However, adapting culture parameters like the oxygen tension or the osmolarity to their physiological values is often omitted. Indeed, articular cartilage is an avascular tissue subjected to reduced oxygen tension and presenting and increased osmolarity compared with most other tissues. In this study, we aimed at evaluating the effect of a physiological oxygen tension (3% instead of 21%) and physiological osmolarity (430 vs. 330 mOsm in nonadjusted DMEM) and the combination of both on the cell proliferation, matrix production, and the phenotype of porcine chondrocytes in a scaffold-free 3D culture system. We observed that a physiological osmolarity had no effect on cell proliferation and matrix production but positively influences the chondrocyte phenotype. A physiological oxygen level prevented cell proliferation but resulted in an increased matrix content/million cells and had a positive influence on the chondrocyte phenotype as well. The strongest benefit was reached with the combination of both physiological osmolarity and oxygen levels; with these conditions, type I collagen expression became undetectable. In addition, at 3% O₂ the chondrocytes-matrix constructs were found to more closely resemble native cartilage regarding the matrix-to-cell ratio. In conclusion, this study clearly demonstrates the benefit of using physiological oxygen tension and osmolarity in cartilage tissue engineering with the combination of both showing the strongest benefit on the chondrocyte phenotype.

Tissue Engineering: Then, Now, and the Future

IMPACT STATEMENT

This "invited submission" concisely reviews the author's involvement in the early era of tissue engineering and summarizes his perspective. He points out the journal was present in this early era and that it functions as a viewing chamber for seeing the last 25 years of progress and that it stands ready to provide viewing of the next 25 years.

The initial repair response of articular cartilage after mechanically induced damage

The regenerative potential of articular cartilage (AC) defects is limited and depends on defect size, biomechanical conditions, and age. Early events after overloading might be predictive for cartilage degeneration in the long term. Therefore, the present aim is to investigate the temporal response of cartilage to overloading at cell, matrix, and tissue level during the first period after mechanical overloading. In the present study, the effect of high loading (∼8 MPa) at a high rate (∼14 MPa/s) at day 0 during a 9 day period on collagen damage, gene expression, cell death, and biochemical composition in AC was investigated. A model system was developed which enabled culturing osteochondral explants after loading. Proteoglycan content was repeatedly monitored over time using μCT, whereas other evaluations required destructive measurements. Changes in matrix related gene expressions indicated a degenerative response during the first 6 h after loading. After 24 h, this was restored and data suggested an initial repair response. Cell death and microscopic damage increased after 24 h following loading. These degradative changes were not restored within the 9 day culture period, and were accompanied by a slight loss of proteoglycans at the articular surface that extended into the middle zones. The combined findings indicate that high magnitude loading of articular cartilage at a high rate induces an initial damage that later initiates a healing response that can probably not be retained due to loss of cell viability. Consequently, the matrix cannot be restored in the short term. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1265-1273, 2017.

Nondestructive Techniques to Evaluate the Characteristics and Development of Engineered Cartilage

In this review, methods for evaluating the properties of tissue engineered (TE) cartilage are described. Many of these have been developed for evaluating properties of native and osteoarthritic articular cartilage. However, with the increasing interest in engineering cartilage, specialized methods are needed for nondestructive evaluation of tissue while it is developing and after it is implanted. Such methods are needed, in part, due to the large inter- and intra-donor variability in the performance of the cellular component of the tissue, which remains a barrier to delivering reliable TE cartilage for implantation. Using conventional destructive tests, such variability makes it near-impossible to predict the timing and outcome of the tissue engineering process at the level of a specific piece of engineered tissue and also makes it difficult to assess the impact of changing tissue engineering regimens. While it is clear that the true test of engineered cartilage is its performance after it is implanted, correlation of pre and post implantation properties determined non-destructively in vitro and/or in vivo with performance should lead to predictive methods to improve quality-control and to minimize the chances of implanting inferior tissue.

Finite element analysis of the stability of combined plate internal fixation in posterior wall fractures of acetabulum

OBJECTIVE

This study aims to explore the mechanical stability of combined plate internal fixation in posterior wall fractures of the acetabulum.

METHODS

The fracture and internal fixation models were established in this study and they were divided into four kinds of internal fixation models, finite element analysis was performed. The four groups were 2 mini-plates and 1 reconstruction plate fixation (A), Reconstruction plate internal fixation group (B), 2 screws internal fixation group (C) and mini-plates internal fixation group (D). The displacement of each node was measured and evaluated.

RESULTS

There was no distortion in the geometric shape of the finite element model. The results of stress showed that it was less in the anterior pelvic ring and distributed uniform in labrum acetabulare; the stress was bigger in the upper and middle of sacroiliac joint and sciatic notch in sitting position.

CONCLUSIONS

Combined plate internal fixation for posterior wall fractures of acetabular were stable and reliable, it is better than the other three methods.

Ultrasound Elastography for Estimation of Regional Strain of Multilayered Hydrogels and Tissue-Engineered Cartilage

Tissue-engineered (TE) cartilage constructs tend to develop inhomogeneously, thus, to predict the mechanical performance of the tissue, conventional biomechanical testing, which yields average material properties, is of limited value. Rather, techniques for evaluating regional and depth-dependent properties of TE cartilage, preferably non-destructively, are required. The purpose of this study was to build upon our previous results and to investigate the feasibility of using ultrasound elastography to non-destructively assess the depth-dependent biomechanical characteristics of TE cartilage while in a sterile bioreactor. As a proof-of-concept, and to standardize an assessment protocol, a well-characterized three-layered hydrogel construct was used as a surrogate for TE cartilage, and was studied under controlled incremental compressions. The strain field of the construct predicted by elastography was then validated by comparison with a poroelastic finite-element analysis (FEA). On average, the differences between the strains predicted by elastography and the FEA were within 10%. Subsequently engineered cartilage tissue was evaluated in the same test fixture. Results from these examinations showed internal regions where the local strain was 1-2 orders of magnitude greater than that near the surface. These studies document the feasibility of using ultrasound to evaluate the mechanical behaviors of maturing TE constructs in a sterile environment.

Physicochemical and biomechanical stimuli in cell-based articular cartilage repair

Articular cartilage is a unique load-bearing connective tissue with a low intrinsic capacity for repair and regeneration. Its avascularity makes it relatively hypoxic and its unique extracellular matrix is enriched with cations, which increases the interstitial fluid osmolarity. Several physicochemical and biomechanical stimuli are reported to influence chondrocyte metabolism and may be utilized for regenerative medical approaches. In this review article, we summarize the most relevant stimuli and describe how ion channels may contribute to cartilage homeostasis, with special emphasis on intracellular signaling pathways. We specifically focus on the role of calcium signaling as an essential mechanotransduction component and highlight the role of phosphatase signaling in this context.