Effect of total occlusal convergence on fit and fracture resistance of zirconia-reinforced lithium silicate crowns

Introduction

Computer-aided design (CAD) and computer-aided manufacturing (CAM) monolithic crowns are gaining momentum. Limited evidence exists about the effect of tooth preparation total occlusal convergence (TOC) on marginal and internal gap distances in addition to load to fracture values.

Aim

The aim of this study was to evaluate, by microcomputed tomography (µCT), the influence of 12° and 20° TOC on marginal and internal adaptation of zirconia-reinforced lithium silicate (ZLS) crowns. Moreover, values of load to fracture with and without initial cyclic loading (CL) were compared.

Material and methods

Forty ZLS crowns were fabricated on dies with TOC of 12° and 20°, 20 crowns for each group. µCT was used to compare marginal and internal adaptation. Each specimen was measured at 140 points distributed on all tooth preparation surfaces for 2D gap distance assessment. 3D gap volume was also evaluated. Crowns were then cemented and divided into two subgroups; the first was stored in distilled water (no cyclic loading [NCL] subgroup), the second was subjected to CL (CL subgroup).

Results

Factorial repeated measures ANOVA followed by Bonferroni post hoc in addition to independent and dependent t-tests were used for statistical analysis. Marginal gap, absolute marginal discrepancy, and occlusal gap measurements showed significant differences between the measurement sites. Static load to fracture values showed significant differences between TOC groups for both NCL (P=0.011) and CL (P=0.025) subgroups.

Conclusion

An increase of TOC from 12° to 20° did not affect marginal and internal adaptation but resulted in higher values of load to fracture of ZLS crowns. CL simulating 1 year of service did not result in fatigue failure.

The influence of polishing techniques on pre-polymerized CAD\CAM acrylic resin denture bases

Background

Lately, computer-aided design and computer-aided manufacturing (CAD/CAM) has broadly been successfully employed in dentistry. The CAD/CAM systems have recently become commercially available for fabrication of complete dentures, and are considered as an alternative technique to conventionally processed acrylic resin bases. However, they have not yet been fully investigated.

Objective

The purpose of this study was to inspect the effects of mechanical polishing and chemical polishing on the surface roughness (Ra) and contact angle (wettability) of heat-cured, auto-cured and CAD/CAM denture base acrylic resins.

Methods

This study was conducted at the Advanced Dental Research Laboratory Center of King Abdulaziz University from March to June 2017. Three denture base materials were selected: heat cure poly-methylmethacrylate resin, thermoplastic (polyamide resin) and (CAD\CAM) denture base resin. Sixty specimens were prepared and divided into three groups, twenty in each. Each group was divided according to the polishing techniques into (Mech P) and (Chem P), ten specimens in each; surface roughness and wettability were investigated. Data were analyzed by SPSS version 22, using one-way ANOVA and Pearson coefficient.

Results

One-way analysis of variance (ANOVA) and post hoc tests were used for comparing the surface roughness values between three groups which revealed a statistical significant difference between them (p₁<0.001). Heat-cured denture base material of (Group I) in both methods, showed the highest mean surface roughness value (2.44±0.07, 2.72±0.09, Mech P and Chem P respectively); while CAD\CAM denture base material (group III) showed the least mean values (1.08±0.23, 1.39±0.31, Mech P and Chem P respectively). CAD/CAM showed the least contact angle in both polishing methods, which were statistically significant at 5% level (p=0.034 and p<0.001).

Conclusion

Mechanical polishing produced lower surface roughness of CAD\CAM denture base resin with superior smooth surface compared to chemical polishing. Mechanical polishing is considered the best effective polishing technique. CAD/CAM denture base material should be considered as the material of choice for complete denture construction in the near future, especially for older dental patients with changed salivary functions, because of its wettability.