Prospective Clinical Study with New Materials for Tissue Regeneration: A Study in Humans

OBJECTIVE

 This study was performed to evaluate the clinical, radiographic, and histomorphometric outcomes of novel bone grafting materials and dental membranes and to compare the results with current data from the literature.

MATERIALS AND METHODS

 New synthetic bone substitutes, consisting of biphasic calcium phosphate in the ratio of 60% hydroxyapatite and 40% β-tricalcium phosphate, were applied in bony defects and covered by either a novel synthetic poly(lactic-co-glycolic) acid (PLGA) or porcine collagen membrane. A sample of 51 biomaterials was placed in a total of 20 patients during different surgical protocols. Implants were simultaneously inserted, and in the case of sinus floor elevations 6 months later. Pre- and postoperative cone-beam computed tomographies were taken. Bone biopsies were harvested from augmented sides and processed for histomorphometric evaluation.

STATISTICAL ANALYSIS

 Averages and ranges were calculated for the percentage of newly formed bone, residual biomaterial, and connective tissue. Data were submitted to analyze the radiological mean differences in length, width, and density. Paired t-tests were deployed for the analysis of differences within each group between the baseline (preoperative) and the final (postoperative) measurements.

RESULTS

 The mean bone gain in length and width were 0.96 ± 3.33 mm (+27.59%) and 1.22 ± 1.87 mm (+30.48%), respectively. The bone density was increased by a factor of 4, reaching an average of 387.47 ± 328.86 HU. Histomorphometric evaluations revealed new bone formation of 41.44 ± 5.37%, residual biomaterial of 24.91 ± 7.31%, and connective tissue of 33.64 ± 4.81%. The mean healing period was 8.32 ± 3.00 months.

CONCLUSIONS

 Data from this study confirmed the suitability of the tested materials in dental surgery. The biomaterials may be recommended for various clinical procedures. A satisfactory level of increase of new bone was reported in augmented sides. No significant differences were observed between the tested membranes. PLGA membranes might be superior to collagen membranes for their easier handling.

Ozonized Hydrogels vs. 1% Chlorhexidine Gel for the Clinical and Domiciliary Management of Peri-Implant Mucositis: A Randomized Clinical Trial

Peri-implant mucositis consists of a reversible inflammation of peri-implant tissues characterized by bleeding on gentle probing in the absence of bone loss. Ozone therapy is being extensively studied for its efficacy in treating different dental conditions. To date, few studies have evaluated ozone as an adjunct to the oral hygiene measures of peri-implant mucositis patients. The aim of the present study is to assess the efficacy of an ozonized gel (Trial group) compared to chlorhexidine (Control group) after a domiciliary protocol of oral hygiene in a 6-month study. According to a split-mouth study design, patients were divided into Group 1 for the application of chlorhexidine gel in peri-implant mucositis sites of quadrants Q1 and Q3, whereas in quadrants Q2 and Q4, the ozonized gel was in-office administered. For Group 2, the quadrants were inverted. At baseline (T0), and after 1 (T1), 2 (T2), and 3 (T3) months, Probing Depth (PD), Plaque Index (PI), SI Suppuration Index (SI), Bleeding Score (BS) and Marginal Mucosa Condition (MMC) were measured. A statistically significant decrease was found for all the variables assessed in each group (p < 0.05), whereas significant intergroup differences were found only for PI, BoP, and BS. Accordingly, both agents tested in this study showed an efficacy in treating peri-implant mucositis. The ozonized gel deserves particular attention, considering the better outcome than chlorhexidine on specific clinical periodontal parameters, as well as its lesser shortcomings.

Socket-shield technique: the influence of the length of the remaining buccal segment of healthy tooth structure on peri-implant bone and socket preservation. A study in dogs

OBJECTIVE

The aim of this study was to evaluate the influence of the location and length of root pieces on buccal peri-implant bone width and socket preservation in socket shield technique.

MATERIAL AND METHODS

Forty-eight dental implants (24 narrow and 24 regular platform internal hex implants) were placed in six dogs. The clinical crowns of teeth P2, P3, P4 and M1 were detached horizontally and removed from the underlying roots. Then the mesial root of each tooth was extracted and the distal root was degraded using a high-speed hand-piece with round bur, creating a concave shell of dentin cementum and periodontal ligament (PDL) connected to the buccal aspect of the socket. Remaining root fragments of different lengths were created: coronal (1/3); middle and coronal (2/3); full length (3/3). These were positioned all around the bone crest. Implants were placed at the center of the root sockets, 1-3mm deeper than the original root apex. RFA and histological evaluations were made at 4 and 12 weeks. Data underwent statistical analysis (p<0.05).

RESULTS

All 48 implants osseointegrated satisfactorily. On both buccal and lingual sides, the coronal (1/3) radicular fragment was attached to the buccal bone plate by physiologic periodontal ligament with less crestal bone resorption compared with middle (2/3) and whole root (3/3) groups for narrow and standard implants.

CONCLUSIONS

Within the limitations of this study, the results demonstrate that a small piece of root in the coronal part of the alveolus can protect the buccal, mesial and distal bone crest following the immediate placement of NeO narrow or NeO Standard Internal Hex implants. The thickness of peri-implant bone and the remaining root fragment together will provide a total thickness of >2mm. The technique would appear to be highly predictable, maintaining bone volume and reducing the risk of crestal bone resorption.

Evaluation of the Surrounding Ring of Two Different Extra-Short Implant Designs in Crestal Bone Maintanence: A Histologic Study in Dogs

The aim of this study was to compare the implant stability and bone resorption and formation of two different extra-short implant designs with different diameter rings placed in a dog´s maxilla. Thirty-six extra-short, 5 mm diameter × 4 mm length (Short DM^®, Bioner Sistemas Implantológicos, Barcelona, Spain), delayed implants were placed in each hemimaxilla of six dogs at the bone crest level. Eighteen implants of each design (wide and narrow ring) were installed. After 8 and 12 weeks of healing, histomorphometric analyses of the specimens were carried out to measure the crestal bone level values and the tissue thickness around the wide and narrow ring implant designs. In the microscopic analysis, less buccal bone resorption was observed in the narrow ring implants with a statistical significance (p < 0.001). For the peri-implant tissue thickness, the distance from the implant shoulder to the external portion of the epithelium was significantly higher for the implants installed with a wide ring with statistical significance (p < 0.001). Our findings suggest that the amount of peri-implant tissues (crestal bone loss) after remodeling over a period of 12 weeks was smaller in the narrow ring extra-short implant installed in the healed maxilla, compared with the wide ring extra-short implants.

Peri-implant bone loss clinical and radiographic evaluation around rough neck and microthread implants: a 5-year study

OBJECTIVE

To evaluate marginal bone loss over 5 years around microthreaded implants placed in the maxillary anterior/esthetic zone and immediate restored with non-occlusal loading.

MATERIALS AND METHODS

Seventy-one implants (with microthreads up to the platform-rough surface body and neck, internal connection and platform switching) were placed in healed bone in the maxillary arches of 30 men and 23 women (mean age 37.85 ± 7.09 years, range 27-60). All subjects had at least 3 mm of soft tissue to allow the establishment of adequate biologic width and to reduce bone resorption. Each patient received a provisional restoration immediately after implant placement with slight occlusal contact. Mesial and distal bone height was evaluated using digital radiography on the day following implant placement (baseline) and after 1, 2, 3, 4 and 5 years. Primary stability was measured with resonance frequency analysis.

RESULTS

No implants failed, resulting in a cumulative survival rate of 100% after 3 years. Marginal bone loss from implant collar to bone crest measured at baseline (peri-implant bone defect at the fresh extraction socket) and after 5 years was 0.90 mm ± 0.26 mm. Mesial and distal site crestal bone loss ranged from 3.42 ± 1.2 mm at baseline to 3.51 ± 1.5 mm after 5 years and from 3.38 ± 0.9 mm at baseline to 3.49 ± 0.9 mm after 5 years, respectively (P = 0.086).

CONCLUSIONS

The results of this study showed limited implant crestal bone loss 0.90 mm ± 0.26 mm and 100% of implant survival rate at 5-year follow-up of immediate restored implants with rough surface neck and microthreads.

Evaluation of the insertion torque, implant stability quotient and drilled hole quality for different drill design: an in vitro Investigation

OBJECTIVE

The purpose of the present study was to compare the insertion torque and implant stability quotient between different drill design for implant site preparation.

MATERIALS AND METHODS

Synthetic blocks of bone (type I density) were used for drilling procedures. Three groups were evaluated: Group G1 - drilling with a single bur for a 4.2 mm conical implant; Group G2 and Group G3 - drilling with three consecutive burs for a 4.1 mm cylindrical implant and for a 4.3 mm conical implant respectively. For each group, 15 drilling procedures were performed without irrigation for 10-mm in-depth. The drilled hole quality (HQ) after the osteotomy for implant site preparation was measured in the five-first holes through a fully automated roundness/cylindricity instrument at three levels (top, middle, and bottom of the site). The insertion torque value (ITV) was achieved with a computed torquimeter and the implant stability quotient (ISQ) values were measured using a resonance frequency apparatus.

RESULTS

The single drill (group 1) achieved a significantly higher ITV and ISQ than the multiple drills for osteotomy (groups 2 and 3). Group 1 and 3 displayed significantly better HQ than group 2.

CONCLUSIONS

Within the limitations of the study, the results suggest that the hole quality, in addition to the insertion torque, may significantly affect implant primary stability.

The influence of three different apical implant designs at stability and osseointegration process: experimental study in rabbits

OBJECTIVES

The aim of this study was to perform a histomorphometric and biomechanical comparison of three implants with different designs of the apical area to promote a better bone initial stability and its correlation with the osseointegration.

MATERIAL AND METHODS

Fifty-four tapered implants with same length, diameter and surface properties but with three different apical configurations (Group I: MK4: Group II: C1 and Group III: MK7) were inserted in the tibia of rabbits. Implant stability and bone formation were evaluated by resonance frequency analysis measured at 0, 6, 8 and 12 weeks and by histomorphometric analysis performed at 6, 8 and 12 weeks.

RESULTS

Statistical test to compare the stability through the implant stability quotient in the four times showed few differences between the groups and time periods proposed, with significance set at P < 0.05. In the bone-implant contact, by comparing the groups in the three times proposed, it was possible concluded that there is a similar behavior among the three implant design (P < 0.05).

CONCLUSION

With the limitations of this animal study, it can be concluded that the design of the apical area influences the implant stability and the bone-to-implant contact.

Influence of hydroxyapatite granule size, porosity, and crystallinity on tissue reaction in vivo. Part A: synthesis, characterization of the materials, and SEM analysis

OBJECTIVE

The aim of this study was the synthesis and analysis of the tissue reaction to three different Hydroxyapatite (HA)-based bone substitute materials differing only in granule size, porosity, and crystallinity through an animal experimental model at 60 days.

MATERIALS AND METHODS

Three different HA-based biomaterials were synthesized and characterized by X-ray diffraction, SEM, and EDS analysis, the resultant product was ground in three particle sizes: Group I (2000-4000 μm), Group II (1000-2000 μm), and Group III (600-1000 μm). Critical size defects were created in both tibias of 15 rabbits. Four defects per rabbit for a total of 60 defects were grafted with the synthesized materials as follows: Group I (15 defects), Group II (15 defects), Group III (15 defects), and empty (15 defects control). After animals sacrifice at 60 days samples were obtained and processed for SEM and EDS evaluation of Ca/P ratios, elemental mapping was performed to determine the chemical degradation process and changes to medullary composition in all the four study groups.

RESULTS

The tendency for the density was to increase with the increasing annealing temperature; in this way it was possible to observe that the sample that shows highest crystallinity and crystal size corresponding to that of group I. The SEM morphological examination showed that group III implant showed numerous resorption regions, group II implant presented an average resorption rate of all the implants. The group I displayed smoother surface features, in comparison with the other two implants.

CONCLUSION

The data from this study show that changing the size, porosity, and crystallinity of one HA-based bone substitute material can influence the integration of the biomaterials within the implantation site and the new bone formation.

Evaluation of extrashort 4-mm implants in mandibular edentulous patients with reduced bone height in comparison with standard implants: a 12-month results

OBJECTIVE

The aim of this research was to evaluate the primary stability, the marginal bone loss, the survival, and the success criteria, of 4-mm-length implants compared with implants of conventional length supporting fixed prostheses.

MATERIALS AND METHODS

Ten patients were selected for treatment of their atrophic edentulous jaws. Each patient received the following treatment: six dental implants were inserted, two anterior implants of conventional length (10-mm) in the interforaminal area and four posterior short implants of 4-mm length (Standard Plus, Roxolid, SLActive, Institut Straumann AG). The implants supported screw-retained fixed complete dentures. Examinations were conducted at day 0, three, six, and twelve months after surgery for the evaluation of the implant primary stability, secondary stability, crestal bone loss and survival by clinical evaluations, insertion torque values, resonance frequency analysis (RFA), and periapical radiography, respectively.

RESULTS

Sixty implants were inserted in ten patients. Mean insertion torque was slightly lower for 4-mm implants than 10-mm implants (38.1 Ncm vs. 42.2 Ncm) but without statistically significant difference. Implant stability was similar for extrashort and conventional implants. Marginal bone loss was similar for both groups for all the time periods. One short implant was lost before loading. The survival rates twelve months after implant placement were of 97.5% and 100% for short and conventional implants, respectively. Similarly, implant stability as measured by RFA was nonsignificantly lower for the 4-mm implants compared to the 10-mm implants. The marginal bone loss was lower for short implants three, six, and twelve months after the surgery without statistical significant difference.

CONCLUSIONS

Within the limitations of this study, we conclude that short dental implants (8 mm or less in length) supporting single crowns or fixed bridges are a feasible treatment option with radiographic and clinical success rates similar to longer implants for patients with compromised ridges. Long-term data with larger number of implants and subjects are needed to confirm these preliminary results.

Submerged flapless technique vs. conventional flap approach for implant placement: experimental domestic pig study with 12-month follow-up

OBJECTIVES

The aim of our study was to compare osseointegration and peri-implant crestal bone resorption in submerged flapless and conventional flap surgery over a 12-month follow-up.

MATERIALS AND METHODS

The study used five domestic pigs. Implants were inserted 9 weeks after tooth extraction. Each animal received six implants in the mandible, following a split-mouth design: one side was treated using a flapless technique using mini-incisions, while a flap was raised on the other. The animals were sacrificed at 2 weeks, 1, 3, 6 and 12 months after implant placement. Radiographic images were taken to analyze crestal bone loss, and samples were extracted for histopathological and bone-to-implant contact (BIC) analyses.

RESULTS

Significantly, greater crestal bone loss (P = 0.005) was obtained in the flap group compared with the flapless group. The flapless group presented significantly higher percentages of BIC (P < 0.05) at 3, 6 and 12 months compared with the conventional flap group.

CONCLUSIONS

Within the limitations of this experimental animal study, it may be concluded that the type of surgery (flap or flapless) affects peri-implant bone preservation and osseointegration of regular platform implants. Flapless surgery is associated with peri-implant crestal bone preservation. Flapless surgery in combination with submerged implants allows higher osseointegration values.