Green preparation of CaO-based CO2 adsorbent by calcium-induced hydrogenation of shell wastes at room/moderate temperature

Capturing CO2 using clamshell/eggshell-derived CaO adsorbent can not only reduce carbon emissions but also alleviate the impact of trash on the environment. However, organic acid was usually used, high-temperature calcination was often performed, and CO2 was inevitably released during preparing CaO adsorbents from shell wastes. In this work, CaO-based CO2 adsorbent was greenly prepared by calcium-induced hydrogenation of clamshell and eggshell wastes in one pot at room/moderate temperature. CO2 adsorption experiments were performed in a thermogravimetric analyzer (TGA). The adsorption performance of the adsorbents obtained from the mechanochemical reaction (BM-C/E-CaO) was superior to that of the adsorbents obtained from the thermochemical reaction (Cal-C/E-CaO). The CO2 adsorption capacity of BM-C-CaO at 650 °C is up to 36.82 wt%, but the adsorption decay rate of the sample after 20 carbonation/calcination cycles is only 30.17%. This study offers an alternative energy-saving method for greenly preparing CaO-based adsorbent from shell wastes.

[Two cases of airway dysfunction related to diacetyl exposure]

Occupational exposure to diacetyl can lead to bronchiolitis obliterans. In this paper, two patients with severe obstructive ventilation disorder who were exposed to diacetyl at a fragrance and flavours factory were analyzed. The clinical manifestations were cough and shortness of breath. One of them showed Mosaic shadows and uneven perfusion in both lungs on CT, while the other was normal. Field investigation found that 4 of the 8 workers in the factory were found to have obstructive ventilation disorder, and 2 had small airway dysfunction. This paper summarizes the diagnostic process of patients in order to improve the understanding of airway dysfunction caused by occupational exposure to diacetyl and promote the development of relevant standards.

[Analysis of dust hazard characteristics in 59 ferrous metal foundry enterprises in Ningbo City]

Objective: To analyze the post distribution of dust concentration in ferrous metal foundry enterprises and evaluate the occupational health risks, and provide basis for policies of the formulation of pneumoconiosis prevention and control. Methods: From August to September in 2020, the basic information, dust hazard information and occupational health management information of 59 ferrous metal casting enterprises were investigated, the dust concentration distribution was analyzed, and the risk assessment was carried out by using the quantitative assignment model. The dust concentration is tested by LSD method after logarithmic treatment. The 3 times time weighted average allowable exposure concentration of dust is taken as the peak concentration limit of dust; The time weighted average allowable exposure concentration of dust converted by exposure time is taken as the time weighted average exposure concentration limit of dust, and whether the time weighted average exposure concentration and peak concentration of dust at the same post exceed the limit is taken as the basis for exceeding the limit of dust post concentration to calculate the post exceeding the limit rate. Results: The dust hazards were mainly distributed in the posts of sand treatment, molding, sand falling, sand cleaning and cutting and grinding. Dust exposure time weighted average concentration was 0.44 (0.03, 5.11) mg/m(3), peak exposure concentration was 1.30 (0.18, 10.94) mg/m(3), and the over standard rate of Posts was 38.92% (79/203) . Weighted average exposure concentration of other dust (total dust) in the cutting and grinding post is 1.50 (0.15, 7.40) mg/m(3), peak exposure concentration is 0.90 (0.07, 12.48) mg/m(3), and the post exceedance rate is 4.88% (2/41) . Weighted average exposure concentration of silica dust (exhaling dust) in dust operation posts of investment casting enterprises is 0.43 (0.05, 6.35) mg/m(3), peak exposure concentration is 0.90 (0.12, 8.28) mg/m(3), and the post over standard rate is 35.77% (49/137) ; Weighted average exposure concentration of other dust (total dust) at the cutting and grinding post is 2.00 (11.00, 21.00) mg/m(3), and the post exceedance rate is 2.50% (2/80) . There was no significant difference in the concentration of respirable dust between sand casting and investment casting (P>0.05) . The concentration of respirable dust in sand casting was higher than that in sand treatment, molding and sand cleaning posts (P<0.05) . The concentration of silica dust in investment casting was higher than that in sand treatment and molding posts, and that in sand cleaning posts was higher than that in sand treatment posts (P<0.05) . 98.48% (454/461) of the dust operation posts have an occupational health risk value greater than or equal to 400, and 1.52% (7/461) of the dust operation posts have an occupational health risk value of 200~399. Conclusion: there is a high rate of exceeding the standard in the dust work posts in the ferrous metal foundry enterprises in Ningbo, and the workers have a high occupational health risk of pneumoconiosis or metal and its compound pneumoconiosis. Targeted measures should be taken to reduce the occupational health risk.

[The application of two occupation health risk assessment models in a wooden furniture manufacturing industry]

Objective: To explore the applicability of 2 different models of occupational health risk assessment in wooden furniture manufacturing industry. Methods: American EPA inhalation risk model and ICMM model of occupational health risk assessment were conducted to assess occupational health risk in a small wooden furniture enterprises, respectively. Results: There was poor protective measure and equipment of occupational disease in the plant. The concentration of wood dust in the air of two workshops was over occupational exposure limit (OEL) , and the C_TWA was 8.9 mg/m³ and 3.6 mg/m³, respectively. According to EPA model, the workers who exposed to benzene in this plant had high risk (9.7×10^-6 ~34.3×10^-6) of leukemia, and who exposed to formaldehyde had high risk (11.4 × 10^-6) of squamous cell carcinoma. There were inconsistent evaluation results using the ICMM tools of standard-based matrix and calculated risk rating. There were very high risks to be attacked by rhinocarcinoma of the workers who exposed to wood dust for the tool of calculated risk rating, while high risk for the tool of standard-based matrix. For the workers who exposed to noise, risk of noise-induced deafness was unacceptable and medium risk using two tools, respectively. Conclusion: Both EPA model and ICMM model can appropriately predict and assessthe occupational health risk in wooden furniture manufactory, ICMM due to the relatively simple operation, easy evaluation parameters, assessment of occupational- disease-inductive factors comprehensively, and more suitable for wooden furniture production enterprise.