Structural Criteria for Amorphization of Network Solids

Amorphization, like glass-formation, represents fundamentally a failure to crystallize. The problem is to understand how atoms can rearrange themselves, perhaps within the confines of unaffected surrounding crystal, after a local disordering event. Some ceramics, like alkali halides and oxides with the rocksalt structure, appear almost impossible to amorphize, forming localized aggregate defects (voids, dislocation loops, colloids) and even decomposing (as a response to radiation disorder), rather than structurally reordering (or disordering). Other network solids such as silicas and silicates readily amorphize. In this study, we attempt to establish topology and structural freedom as criteria for amorphization of network solids.

Characterization of Mineral Deposits on Plasma-Sprayed HA-Coated Ti-6Al-4V

Plasma-sprayed hydroxyapatite (PSHA) coatings are often used as the attachment vehicle for the femoral component of a total hip prosthesis. The key to successful hip replacement is the attachment of the femoral stem to the surrounding bone.

Within hours of implantation of PSHA-coated Ti-6AI-4V rods in canine bone, bone mineral deposits on the HA coating. These deposits take the form of globular networks of fibrous crystallites. The crystallinity of these deposits was confirmed via high-resolution transmission electron microscopy (TEM) and electron diffraction. We have also characterized the composition of these deposits using x-ray energy-dispersive spectroscopy (XEDS) in the scanning TEM. Finally, we have studied the morphology of the fiber-like crystallites by stereography in the TEM.

The ultrastructure of the plasma-sprayed hydroxyapatite-bone interface predisposing to bone bonding

The deposition of biological apatite and subsequent formation of bone on hydroxyapatite implants depends on the partial dissolution of the implant surface and the reprecipitation of carbonated apatite from the biological milieu. Previous investigations in vitro have shown that the degree of dissolution and reprecipitation decreases as the coating crystallinity increases. These findings prompted the current study of the effects of coating crystallinity on the mechanism of bone bonding. The process of mineralization of bone associated with a hydroxyapatite coating was compared to the normal process of ossification. Plasma-sprayed hydroxyapatite (PSHA) coated titanium alloy (6% Al-4% V) rods as received and annealed for 0.7 h at 600 degrees C in air to increase the coating crystallinity were implanted in the proximal and distal femora and proximal tibiae of adult mongrel dogs for 3 h, 3 and 10 days. Bony sites containing the implant were prepared for ultramicrotomy and transmission electron microscopy using an anhydrous embedding procedure: fixation in ethylene glycol and embedment in Spurr's resin. The results demonstrated the precipitation of biological apatite crystallites on non-annealed PSHA coatings in vivo within 3 h of implantation. After 3 and 10 days there were differences in the ultrastructure of the mineral phase on the surfaces of non-annealed and annealed surfaces. Observations showed that there was little difference in the mechanism of mineralization of bone associated with HA-coated prostheses and the normal process of ossification.

The ultrastructure of anorganic bovine bone and selected synthetic hyroxyapatites used as bone graft substitute materials

The objective of this study was to investigate the morphology and organization of apatite crystallites in mature mammalian bone. Anorganic bovine bone was studied in this investigation to allow for the examination of the mineral crystallites after removal of the organic phase. Field-emission low-voltage scanning electron microscopy (FE-LVSEM) was employed to obtain images at nanometer resolution without the application of a conductive coating. Transmission electron microscopy (TEM) of the samples was also performed to confirm the identification of features observed in the SEM and to allow for comparison with earlier studies of bone mineral architecture. For comparison, in order to demonstrate how the interaction of collagen and apatite results in the architecture and crystal structure of bone mineral, two synthetic hydroxyapatite materials were also analyzed: OsteoGen and OsteoGraf/LD300. FE-LVSEM revealed distinctive features of bone mineral: a fibrillar organization of crystallites, a periodic spacing of crystallites along the fibrils consistent with the banding pattern of collagen, inter-fibrillar bridging crystallites, and a plate-like habit of the crystallites. These findings supported the hypothesis, derived from the earlier TEM data of others, that the mineralization of collagen comprising osteoid proceeds by the formation of apatite crystallites within the fibers at selected periodic sites along their length. Moreover, the very presence in this anorganic material of distinct fibers comprised of the crystallites is demonstration of inter-crystallite bonding. The crystallites of the synthetic hydroxyapatite materials did not display any of these ultrastructural features.

Image analysis of insulation mineral fibres

We present two methods for measuring the diameter and length of man-made vitreous fibres based on the automated image analysis of scanning electron microscopy images. The fibres we want to measure are used in materials such as glass wool, which in turn are used for thermal and acoustic insulation. The measurement of the diameters and lengths of these fibres is used by the glass wool industry for quality control purposes. To obtain reliable quality estimators, the measurement of several hundred images is necessary. These measurements are usually obtained manually by operators. Manual measurements, although reliable when performed by skilled operators, are slow due to the need for the operators to rest often to retain their ability to spot faint fibres on noisy backgrounds. Moreover, the task of measuring thousands of fibres every day, even with the help of semi-automated image analysis systems, is dull and repetitive. The need for an automated procedure which could replace manual measurements is quite real. For each of the two methods that we propose to accomplish this task, we present the sample preparation, the microscope setting and the image analysis algorithms used for the segmentation of the fibres and for their measurement. We also show how a statistical analysis of the results can alleviate most measurement biases, and how we can estimate the true distribution of fibre lengths by diameter class by measuring only the lengths of the fibres visible in the field of view.

Radiation damage in stained catalase at low temperature

Radiation damage, which occurs in the beam of the electron microscope, has been studied in uranyl acetate stained crystals. Damage is observed in terms of the disappearance of higher orders of the electron diffraction pattern. In this study it has been found that the damage at very low specimen temperatures proceeds both more rapidly and to a greater final degree than is the case at room temperature.