Comparative microplastic analysis in urban waters using μ-FTIR and Py-GC-MS: A case study in Amsterdam

The contamination of freshwater with microplastics (MPs) has been established globally. While the analysis of MPs has predominantly involved spectroscopic methods for revealing particle numbers, the potential of employing spectroscopy for mass estimation has been underutilized. Consequently, there is a need to enhance our understanding of the mass loads of MPs and ensure the complementarity and comparability of various techniques for accurate quantification. This study presents the first comparative results on urban water samples using micro Fourier-transform infrared (μ-FTIR) imaging and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) to identify and quantify MPs in both particle numbers and mass concentration. Two sampling campaigns in summer and winter were conducted at 11 locations within the Amsterdam canal network. An advanced in-situ volume-reducing sampling pump was employed to collect MPs from the surface water within the size fraction of 10-300 μm. The analysis revealed MP concentrations within the range of 16-107 MP/m3, estimated to be 2.0-789 μg/m3 by μ-FTIR imaging and 8.5-754 μg/m3 by Py-GC-MS. The results of the two analysis techniques showed good comparability in terms of the general trends of MP abundances, with variations in polymer compositions due to the inherent inter-methodological differences. Elevated MP concentrations were observed in the city center compared to the suburban areas. In addition, seasonal differences in MP abundances were noted at the locations with high human activity.

Realistic assessment of tire and road wear particle emissions and their influencing factors on different types of roads

This study aims to examine tire and road wear particle (TRWP) emissions under realistic conditions in order to provide some valuable insights into understanding their sources and fate in the environment. TRWP emissions were evaluated with a fully instrumented vehicle driving on five representative road types: urban, ring road, suburban, highway, and rural. Multiple vehicle dynamic variables were recorded to assess the factors influencing these emissions. For the first time, emitted particles were collected on filters and analyzed by means of pyrolysis coupled with gas chromatography-mass spectrometry to determine the polymeric content of tires, in specifically quantifying styrene-butadiene rubber (SBR) and butadiene rubber (BR) pyrolytic markers. The measurements obtained from the five road types revealed similar size distributions for SBR + BR emissions, with maxima found in the (ultra)fine fraction (< 0.39 µm). Upon applying an SBR + BR-to-TRWP conversion factor, (ultra)fine fraction TRWP emissions proved to be the highest for suburban (64 ± 5 µg/km), followed by highway, urban, ring road and rural routes. The output represents up to 480 tons of TRWP per year emitted in the EU27, thus suggesting a widely impregnated atmospheric compartment capable of threatening human health. Furthermore, an analysis of variables revealed that acceleration, tire constraints, and constant sustained driving factors had specific impacts on TRWP emissions.

Oxidation-driven lignin removal by Agaricus bisporus from wheat straw-based compost at industrial scale

Fungi are main lignin degraders and the edible white button mushroom, Agaricus bisporus, inhabits lignocellulose-rich environments. Previous research hinted at delignification when A. bisporus colonized pre-composted wheat straw-based substrate in an industrial setting, assumed to aid subsequent release of monosaccharides from (hemi-)cellulose to form fruiting bodies. Yet, structural changes and specific quantification of lignin throughout A. bisporus mycelial growth remain largely unresolved. To elucidate A. bisporus routes of delignification, at six timepoints throughout mycelial growth (15 days), substrate was collected, fractionated, and analyzed by quantitative pyrolysis-GC-MS, 2D-HSQC NMR, and SEC. Lignin decrease was highest between day 6 and day 10 and reached in total 42 % (w/w). The substantial delignification was accompanied by extensive structural changes of residual lignin, including increased syringyl to guaiacyl (S/G) ratios, accumulated oxidized moieties, and depleted intact interunit linkages. Hydroxypropiovanillone and hydroxypropiosyringone (HPV/S) subunits accumulated, which are indicative for β-|O-4' ether cleavage and imply a laccase-driven ligninolysis. We provide compelling evidence that A. bisporus is capable of extensive lignin removal, have obtained insights into mechanisms at play and susceptibilities of various substructures, thus we were contributing to understanding fungal lignin conversion.

Influence of Calcium Perchlorate on the Search for Martian Organic Compounds with MTBSTFA/DMF Derivatization

N-tert-butyldimethylsilyl-N-methyltrifluoroacetamide (MTBSTFA), mixed with the solvent N,N-dimethylformamide (DMF), is used as a derivatizing reagent by the Sample Analysis at Mars (SAM) experiment onboard NASA's Curiosity rover and will soon be utilized by the Mars Organic Molecule Analyzer experiment onboard the ESA/Roscosmos Rosalind Franklin rover. The pyrolysis products of MTBSTFA, DMF, and the MTBSTFA/DMF mixtures, obtained at different temperatures, were analyzed. Two different pyrolysis modes were studied, flash pyrolysis and ramp pyrolysis (35°C/min), to evaluate the potential influence of the sample heating speed on the production of products in space chromatographs. The effect of the presence of calcium perchlorate on the pyrolysis products of MTBSTFA/DMF was also studied to ascertain the potential effect of perchlorate species known to be present at the martian surface. The results show that MTBSTFA/DMF derivatization should be applied below 300°C when using flash pyrolysis, as numerous products of MTBSTFA/DMF were formed at high pyrolysis temperatures. However, when an SAM-like ramp pyrolysis was applied, the final pyrolysis temperature did not appear to influence the degradation products of MTBSTFA/DMF. All products of MTBSTFA/DMF pyrolysis are listed in this article, providing a major database of products for the analysis of martian analog samples, meteorites, and the in situ analysis of martian rocks and soils. In addition, the presence of calcium perchlorate does not show any obvious effects on the pyrolysis of MTBSTFA/DMF: Only chloromethane and TBDMS-Cl (chloro-tertbutyldimethylsilane) were detected, whereas chlorobenzene and other chlorine-bearing compounds were not detected. However, other chlorine-bearing compounds were detected after pyrolysis of the Murchison meteorite in the presence of calcium perchlorate. This result reinforces previous suggestions that chloride-bearing compounds could be reaction products of martian samples and perchlorate.

Influence of Calcium Perchlorate on the Search for Organics on Mars with Tetramethylammonium Hydroxide Thermochemolysis

The Mars Organic Molecule Analyzer (MOMA) and Sample Analysis at Mars (SAM) instruments onboard the Exomars 2022 and Mars Science Laboratory rovers, respectively, are capable of organic matter detection and differentiating potentially biogenic from abiotic organics in martian samples. To identify organics, both these instruments utilize pyrolysis-gas chromatography coupled to mass spectrometry, and the thermochemolysis agent tetramethylammonium hydroxide (TMAH) is also used to increase organic volatility. However, the reactivity and efficiency of TMAH thermochemolysis are affected by the presence of calcium perchlorate on the martian surface. In this study, we determined the products of TMAH pyrolysis in the presence and absence of calcium perchlorate at different heating rates (flash pyrolysis and SAM-like ramp pyrolysis with a 35°C·min^-1 heating rate). The decomposition mechanism of TMAH pyrolysis in the presence of calcium perchlorate was studied by using stepped pyrolysis. Moreover, the effect of calcium perchlorate (at Mars-relevant concentrations) on the recovery rate of fatty acids with TMAH thermochemolysis was studied. Results demonstrate that flash pyrolysis yields more diversity and greater abundances of TMAH thermochemolysis products than does the SAM-like ramp pyrolysis method. There is no obvious effect of calcium perchlorate on TMAH degradation when the [ClO₄^-] is lower than 10 weight percent (wt %). Most importantly, the presence of calcium perchlorate does not significantly impact the recovery rate of fatty acids with TMAH thermochemolysis under laboratory conditions, which is promising for the detection of fatty acids via TMAH thermochemolysis with the SAM and MOMA instruments on Mars.

Environmental forensic characterization of former rail yard soils located adjacent to the Statue of Liberty in the New York/New Jersey harbor

Identifying inorganic and organic soil contaminants in urban brownfields can give insights into the adverse effects of industrial activities on soil function, ecological health, and environmental quality. Liberty State Park in Jersey City (N.J., USA) once supported a major rail yard that had dock facilities for both cargo and passenger service; a portion remains closed to the public, and a forest developed and spread in this area. The objectives of this study were to: 1) characterize the organic and inorganic compounds in Liberty State Park soils and compare the findings to an uncontaminated reference site (Hutcheson Memorial Forest); and 2) identify differences between the barren low-functioning areas and the forested high-functioning areas of the brownfield. Soil samples were solvent-extracted, fractionated, and analyzed by gas chromatography-mass spectrometry and subjected to loss-on-ignition, pyrolysis-gas chromatography-mass spectrometry, inductively-coupled-plasma mass spectrometry, and optical microscopy analyses. Compared to soil from the reference site, the forested soils in Liberty State Park contained elevated percentages of organic matter (30-45%) and more contaminants, such as fossil-fuel-derived hydrocarbons and coal particles. Microscopy revealed bituminous and anthracite coal, coke, tar/pitch, and ash particles. Barren and low-functioning site 25R had a similar organic contaminant profile but contained a higher metal load than other Liberty State Park sites and also lacked higher plant indicators. These can obscure the signatures of contaminants, and data from adjacent barren and vegetated sites are valuable references for soils studies. A deeper understanding of the chemistry, biochemistry, and ecology of barren soils can be leveraged to prevent land degradation and to restore dysfunctional and phytotoxic soils.

Characteristics of lignin from flax shives as affected by extraction conditions

Lignin, a polyphenolic molecule, is a major constituent of flax shives. This polyphenolic molecular structure renders lignin a potential source of a variety of commercially viable products such as fine chemicals. This work compares the performance of different lignin isolation methods. Lignin from flax shive was isolated using both conventional alkaline extraction method and a novel experimental pressurized low polarity water (PLPW) extraction process. The lignin yields and chemical composition of the lignin fractions were determined. The conventional alkali treatment with 1.25 M NaOH, heated at 80 °C for 5 h, extracted 92 g lignin per kg flax shives, while lignin yields from the PLPW extracts ranged from 27 to 241 g lignin per kg flax shives. The purity and monomeric composition of the lignins obtained from the different extraction conditions was assessed via UV spectroscopy and alkaline nitrobenzene oxidation. Lignin obtained from conventional alkali treatment with 1.25 M NaOH, heated at 80 °C for 5 h was of low purity and exhibited the lowest yields of nitrobenzene oxidation products. With respect to alkali assisted PLPW extractions, temperature created an opposing effect on lignin yield and nitrobenzene oxidation products. More lignin was extracted as temperature increased, yet the yield of nitrobenzene oxidation products decreased. The low yield of nitrobenzene oxidation products may be attributed to either the formation of condensed structures or the selective dissolution of condensed structures of lignin during the pressurized alkaline high temperature treatment. Analytical pyrolysis, using pyroprobe GC-MS, was used to investigate the molecular composition of the lignin samples. The total yield of pyrolysis lignin products was 13.3, 64.7, and 30.5% for the 1.25 M NaOH extracted lignin, alkaline assisted PLPW extracted lignin, and the unprocessed flax shives, respectively. Key lignin derived compounds such as guaiacol, 4-vinyl guaiacol, 4-methyl guaiacol, syringol, eugenol, isoeugenol, catechol, homocatechol, and vanillin were detected in all of the samples.