Surface adsorption and corrosion resistance performance of modified chitosan: Gravimetric, electrochemical, and computational studies

Two novel chitosan derivatives (water soluble and acid soluble) modified with thiocarbohydrazide were produced by a quick and easy technique using formaldehyde as links. The novel compounds were synthesized and then characterized by thermogravimetric analysis, elemental analysis, nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, and differential scanning calorimetry. Their surface morphologies were examined using scanning electron microscopy. These chitosan derivatives could produce pH-dependent gels. The behavior of mild steel in 5 % acetic acid, including both inhibitors at various concentrations, was investigated using gravimetric and electrochemical experiments. According to the early findings, both compounds (TCFACN and TCFWCN) functioned as mixed-type metal corrosion inhibitors. Both inhibitors showed their best corrosion inhibition efficiency at 80 mg L-1. TCFACN and TCFWCN, showed approximately 92 % and 94 % corrosion inhibition, respectively, at an optimal concentration of 80 mg L-1, according to electrochemical analysis. In the corrosion test, the water contact angle of the polished MS sample at 87.90 °C was reduced to 51 °C. The water contact angles for MS inhibited by TCFACN and TCFWCN in the same electrolyte were greater, measuring 78.10 °C and 93.10 °C, respectively. The theoretical results also support the experimental findings.

Structural and surface studies of luminescent Ca/Eu phosphate nanomaterials: From the bulk to surface features

Three luminescent Eu-containing phosphate materials (Ca-doped europium phosphate monohydrate, Eu-doped carbonated-apatite, and europium phosphate monohydrate) were prepared and analyzed on the level of bulk structure and surface properties and compared to the biomimetic non-luminescent counterpart hydroxyapatite. Europium-containing phosphate materials exhibited nanosized dimensions but different luminescence emissions and luminescence lifetimes depending on their crystalline structures (i.e., lanthanide phosphate or apatites) and chemical composition. The introduction of Eu in the crystal lattice leads to a notable decrease in the overall Lewis acidity of the surface cationic sites detected by CO probing. Further, the mixed Eu/Ca-containing materials surfaces were found to be very similar to the reference hydroxyapatite in terms of water adsorption energy, while the pure europium phosphate resulted to have the notably higher energy values of direct interaction of water molecules with the surface cations with no detected propagation of this effect towards water overlayers.

Influence of ultrasonic combined supercritical-CO2 electrodeposition process on copper film fabrication: Electrochemical evaluation

Introducing ultrasound irradiation to the electrodeposition process can significantly improve the physical and chemical properties of deposited films. Meanwhile, the beneficial effects from supercritical-CO_2, such as high diffusivity, high permeability, low surface tension, etc., would improve the electrodeposition process with better surface quality. In the shed of the light, the present work deals with the preparation of copper (Cu) films using the integrated techniques, i.e., ultrasonic-assisted supercritical-CO₂ (US-SC-CO₂) electrodeposition approach. For comparison, Cu films were also prepared by normal supercritical-CO₂ (SC-CO₂) and conventional electrodeposition methods. To investigate the characteristics of Cu films, surface morphology analysis, roughness analysis, X-ray diffraction studies (XRD), Linear polarization, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) were performed. In this work, EIS analysis was utilized for interfacial charge transfer resistance analysis with 5 mM [Fe(CN)₆]^-3/-4 redox system and corrosion analysis with 3.5 wt% NaCl solution. The observed results revealed that the film prepared with the US-SC-CO₂ method have superior properties than those produced by normal SC-CO₂ and conventional methods. Due to the combination of US-SC-CO₂, the cavitation implosion occurs rapidly that enriches the deposited film quality, such as sufficient grain size, smoother surface, enhanced corrosion resistance, and charge carrier dynamics. On the other hand, the ultrasound effect with SC-CO₂ helped to remove the weakly adhered metal ions on the electrode's surface.