Effective and Efficient Porous CeO2 Adsorbent for Acid Orange 7 Adsorption

A porous CeO₂ was synthesized following the addition of guanidine carbonate to a Ce³⁺ aqueous solution, the subsequent addition of hydrogen peroxide and a final hydrothermal treatment. The optimal experimental parameters for the synthesis of porous CeO₂, including the amounts of guanidine carbonate and hydrogen peroxide and the hydrothermal conditions, were determined by taking the adsorption efficiency of acid orange 7 (AO7) dye as the evaluation. A template-free hydrothermal strategy could avoid the use of soft or hard templates and the subsequent tedious procedures of eliminating templates, which aligned with the goals of energy conservation and emission reduction. Moreover, both the guanidine carbonate and hydrogen peroxide used in this work were accessible and eco-friendly raw materials. The porous CeO₂ possessed rapid adsorption capacities for AO7 dye. When the initial concentration of AO7 was less than 130 mg/L, removal efficiencies greater than 90.0% were obtained, achieving a maximum value of 97.5% at [AO7] = 100 mg/L and [CeO₂] = 2.0 g/L in the first 10 min of contact. Moreover, the adsorption-desorption equilibrium between the porous CeO₂ adsorbent and the AO7 molecule was basically established within the first 30 min. The saturated adsorption amount of AO7 dye was 90.3 mg/g based on a Langmuir linear fitting of the experimental data. Moreover, the porous CeO₂ could be recycled using a NaOH aqueous solution, and the adsorption efficiency of AO7 dye still remained above 92.5% after five cycles. This study provided an alternative porous adsorbent for the purification of dye wastewater, and a template-free hydrothermal strategy was developed to enable the design of CeO₂-based catalysts or catalyst carriers.

Biological evaluation of a novel bilirubin adsorbent and its therapeutic effect on animal models of hyperbilirubinemia

Hyperbilirubinemia caused severe hepatobiliary diseases with various causes, especially hepatic fibrosis and cirrhosis caused by end-stage hepatitis B and C. Plasma adsorption perfusion (PP) has a tremendous advantage in treating patients with hyperbilirubinemia and liver failure, wherein, a safe and effective adsorbent is the key to filter out bilirubin successfully in PP. In this work, a simple engineering strategy, a new porous polymer adsorption resin ERM-0100 based on the homopolymer predispersion system, is proposed to produce high-performance bilirubin adsorbents. Preliminary experimental results show that ERM-0100 exhibits a large surface area and uniformly porous structure. Experimental results verify that ERM-0100 has high biocompatibility and bilirubin adsorption efficiency (TBIL:35%, direct bilirubin [DBIL]:30%, IBIL:87%) that is significantly higher than most of the reported adsorbents. Animal experiments prove that ERM-0100 has high bilirubin adsorption efficiency and can improve the liver function of animals. The combination of high biocompatibility and high adsorption capacity positions the ERM-0100 as a promising candidate for bilirubin removal.

Facile Fabrication of a Functional Filter Tip for Highly Efficient Reduction of Nicotine Content in Mainstream Smoke

The nicotine addiction problem is of great concern, particularly in adolescents. Notably, nicotine addiction drives humans to continue smoking. Notably, several diseases and disorders are caused by smoking. To date, various adsorbents have been proposed to develop a functionalization filter tip for reducing nicotine content in mainstream smoke. However, the nicotine adsorption efficiencies of most of the reported functionalization filter tips were not satisfactory, and their preparation process was complex and time-consuming. Herein, we demonstrate a highly active and adsorbing filter tip for cigarettes, fabricated by decorating polydopamine (PDA) on the surface of a commercial filter tip in situ. The PDA coating on the filter tip was obtained by the self-polymerization of dopamine (DA) within 16 h, which was quicker and easier than the preparation processes of other reported functionalized filter tips. Significantly, the PDA-decorated filter tip had a nicotine adsorption efficiency as high as ∼95%, which was much higher than most of the commercial filter tips.

Adsorption of Hexavalent Chromium and Divalent Lead Ions on the Nitrogen-Enriched Chitosan-Based Activated Carbon

Optimizing the physicochemical properties of the chitosan-based activated carbon (Ch-ACs) can greatly enhance its performance toward heavy metal removal from contaminated water. Herein, Ch was converted into a high surface area (1556 m2/g) and porous (0.69 cm3/g) ACs with large content of nitrogen (~16 wt%) using K2CO3 activator and urea as nitrogen-enrichment agents. The prepared Ch-ACs were tested for the removal of Cr(VI) and Pb(II) at different pH, initial metal ions concentration, time, activated carbon dosage, and temperature. For Cr(VI), the best removal was at pH = 2, while for Pb(II) the best pH for its removal was in the range of 4-6. At 25 °C, the Temkin model gives the best fit for the adsorption of Cr(VI), while the Langmuir model was found to be better for Pb(II) ions. The kinetics of adsorption of both heavy metal ions were found to be well-fitted by a pseudo-second-order model. The findings show that the efficiency and the green properties (availability, recyclability, and cost effectiveness) of the developed adsorbent made it a good candidate for wastewaters treatment. As preliminary work, the prepared sorbent was also tested regarding the removal of heavy metals and other contaminations from real wastewater and the obtained results were found to be promising.

Determination of the Optimum Removal Efficiency of Fine Particulate Matter Using Activated Carbon Fiber (ACF)

In Korea, concentrations of particulate matter (PM₁₀) are significantly higher in urban railway tunnels (178.1 μg/m³) than in metropolitan areas (49 μg/m³). In railway tunnels in Korea, it was maintained at 3–4 times higher concentration than general atmosphere and platform. Dust generated by trains is scattered at high speed in these tunnels, making filtration difficult; therefore, the development of filters that can be maintained in tunnels is required. In the present study, we examined PM adsorption in the laboratory scale using activated carbon fiber (ACF), which has high adsorption and capacity. The ACF depth, velocity of flow, and fine PM concentration in the tunnel were the experimental variables. We compared PM concentrations before and after the filter experiments, and calculated removal efficiency to determine the optimal conditions. Comprehensive examination of the experimental variables and differential pressure showed that the optimal conditions for an ACF specimen were a wind speed of 3.0 m/s and the ACF depth of 400 mm. The average removal efficiency of PM₁₀ was 55.5%, and that of PM_2.5 was 36.6%. The reproducibility tests showed that the ACF filter could be washed and reused and is suitable for various places because it is easily maintained.

Efficiency of Differently Processed Membranes Based on Cellulose as Cationic Dye Adsorbents

In order to minimize the pollution caused by the reuse of textile dyes, technologies and materials have been developed that purify waste water in an efficient and cost-effective manner before it is discharged into a water body. In this context, the presented research investigates the potential of two types of fully cellulose-based membranes as adsorbents for cationic dyes used in the textile industry. The first type combines cellulose nanofibrils (CNFs) and carboxymethylated cellulose (CMC) using the solvent casting process and an esterification coupling reaction, while the second type uses commercial bacterial cellulose (BC) in a native and sodium periodate-treated form (BCox). The corresponding membranes were comprehensively evaluated by means of Fourier Transform Infrared (FTIR) Spectroscopy. Results confirm the esterification process within the CNF/CMC membranes, as well as BC oxidation after periodate treatment, as shown by bands at 1726.2 cm⁻¹ and 895 cm⁻¹, respectively. The Potentiometric Titration shows the highest total negative charge of 1.07 mmol/g for 4CNF/4CMC, which is assigned to the presence of COO⁻ within CMC polymers, and lowest (0.21 mmol/g) for BCox. The Contact Angle Goniometry data confirm the hydrophilicity of all membranes, and the angle increased from 0 ° (in pure BC) to 34.5 ° in CMC-rich and to 31.4 ° in BCox membranes due to the presence of CH₂COO⁻ and CHO groups, respectively. Confocal Fluorescent Microscopy (CFM) demonstrated the highest µ-roughness in 4CNF/4CMC, while Scanning Electron Microscopy (SEM) depicted diverse morphological features between the membranes, from ultrafine nanofiber networks (in BC and BCox) to larger fiber bundles connected within the polymer phase in CNF/CMC membranes. The adsorption experiment followed by UV–VIS spectroscopy, showed ~100% dye removal efficiency in both CNF/CMC-based membranes, while BC and BCox adsorbed only 24.3% and 23.6%, respectively, when anthraquinone dye was used. Azo dye was only adsorbed with an efficiency of 7–9% on CMC/CNF-based membranes, compared with 5.57% on BC and 7.33% on BCox membranes. The adsorption efficiency at equilibrium was highest for BC (1228 mg/g) and lowest for 7CNF/1CMC (419.24 mg/g) during anthraquinone dye adsorption. In the case of azo dye, the BCox was most effective, with 445.7 mg/g. Applicability of a pseudo second-order model was confirmed for both dyes and all membranes, except for BCox in combination with azo dye, showing the fastest adsorption rate in the case of the 7CNF/1CMC membrane.

Modification of chitin with kraft lignin and development of new biosorbents for removal of cadmium(II) and nickel(II) ions

Novel, functional materials based on chitin of marine origin and lignin were prepared. The synthesized materials were subjected to physicochemical, dispersive-morphological and electrokinetic analysis. The results confirm the effectiveness of the proposed method of synthesis of functional chitin/lignin materials. Mechanism of chitin modification by lignin is based on formation of hydrogen bonds between chitin and lignin. Additionally, the chitin/lignin materials were studied from the perspective of waste water treatment. The synthetic method presented in this work shows an attractive and facile route for producing low-cost chitin/lignin biosorbents with high efficiency of nickel and cadmium adsorption (88.0% and 98.4%, respectively). The discovery of this facile method of synthesis of functional chitin/lignin materials will also have a significant impact on the problematic issue of the utilization of chitinous waste from the seafood industry, as well as lignin by-products from the pulp and paper industry.