Peculiar Properties of Template-Assisted Aniline Polymerization in a Buffer Solution Using Laccase and a Laccase-Mediator System as Compared with Chemical Polymerization

The conventional chemical polymerization of aniline has been described in multiple publications, while enzymatic polymerization has been poorly explored. A comparative study of the template-assisted enzymatic and chemical polymerization of aniline in a buffer solution of sodium dodecylbenzenesulfonate micelles was performed for the first time. The high-redox potential laccase from the fungus Trametes hirsuta was used as a catalyst and air oxygen served as an oxidant. Potentiometric and spectral methods have shown that oligomeric/polymeric products of the enzymatic polymerization of aniline are synthesized in the conducting emeraldine salt form immediately after the reaction is initiated by the enzyme. The use of the laccase-mediator system enabled a higher rate of enzymatic polymerization and a higher yield of final products. Potassium octocyanomolybdate (IV) served as a redox mediator. The products of the enzymatic polymerization of aniline were studied by the ATR-FTIR, MALDI-TOF and atomic force microscopy methods. The chemical oxidative polymerization of aniline under the same conditions resulted in forming a non-conducting dark brown product.

Synthesis and characterization of some novel polythiophene derivatives containing pyrazoline

Eight polythiophene derivatives containing pyrazoline side groups were synthesized by a chemical oxidative coupling polymerization using FeCl₃. The crystal structures of four monomers were determined which confirm the almost perpendicular orientation of the thiophene and pyrazoline rings, while the other substituents are more coplanar. Analyses of IR, ¹H-NMR, Raman and UV-Vis spectra demonstrated that the suggested polymerization was successful to generate the synthesized polythiophenes with the expected structures. The morphology of the synthesized polythiophenes was studied by SEM. The different substituents attached to the 1- and 3-positions of the pyrazoline side chain led to differences in optical properties, electrical conductivity, and thermal stability of the synthesized polythiophenes. By adding a pyrazoline side chain to polythiophenes, some polymers achieve good solubility, electrical conductivity of about 1.3 × 10^–6 S/cm, high fluorescence intensity (above 40,000 a.u.) at 505–550 nm and thermal stability up to 590°C in the air.

Polycarbazole and Its Derivatives: Synthesis and Applications. A Review of the Last 10 Years

Polycarbazole and its derivatives have been extensively used for the last three decades, although the interest in these materials briefly decreased. However, the increasing demand for conductive polymers for several applications such as light emitting diodes (OLEDs), capacitators or memory devices, among others, has renewed the interest in carbazole-based materials. In this review, the synthetic routes used for the development of carbazole-based polymers have been summarized, reviewing the main synthetic methodologies, namely chemical and electrochemical polymerization. In addition, the applications reported in the last decade for carbazole derivatives are analysed. The emergence of flexible and wearable electronic devices as a part of the internet of the things could be an important driving force to renew the interest on carbazole-based materials, being conductive polymers capable to respond adequately to requirement of these devices.

NIR-Triggered Hyperthermal Effect of Polythiophene Nanoparticles Synthesized by Surfactant-Free Oxidative Polymerization Method on Colorectal Carcinoma Cells

In this work, polythiophene nanoparticles (PTh–NPs) were synthesized by a surfactant-free oxidative chemical polymerization method at 60 °C, using ammonium persulphate as an oxidant. Various physicochemical properties were studied in terms of field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Fourier transform infra-red (FT-IR) spectroscopy, and differential scanning calorimetry (DSC)/thermogravimetric analysis (TGA). Photothermal performance of the as-synthesized PTh–NPs was studied by irradiating near infra-red of 808 nm under different concentration of the substrate and power supply. The photothermal stability of PTh–NPs was also studied. Photothermal effects of the as-synthesized PTh–NPs on colorectal cancer cells (CT-26) were studied at 100 µg/mL concentration and 808 nm NIR irradiation of 2.0 W/cm² power. Our in vitro results showed remarkable NIR laser-triggered photothermal apoptotic cell death by PTh–NPs. Based on the experimental findings, it is revealed that PTh–NPs can act as a heat mediator and can be an alternative material for photothermal therapy in cancer treatment.

Cell Uptake and Biocompatibility of Nanoparticles Prepared from Poly(benzyl malate) (Co)polymers Obtained through Chemical and Enzymatic Polymerization in Human HepaRG Cells and Primary Macrophages

The design of drug-loaded nanoparticles (NPs) appears to be a suitable strategy for the prolonged plasma concentration of therapeutic payloads, higher bioavailability, and the reduction of side effects compared with classical chemotherapies. In most cases, NPs are prepared from (co)polymers obtained through chemical polymerization. However, procedures have been developed to synthesize some polymers via enzymatic polymerization in the absence of chemical initiators. The aim of this work was to compare the acute in vitro cytotoxicities and cell uptake of NPs prepared from poly(benzyl malate) (PMLABe) synthesized by chemical and enzymatic polymerization. Herein, we report the synthesis and characterization of eight PMLABe-based polymers. Corresponding NPs were produced, their cytotoxicity was studied in hepatoma HepaRG cells, and their uptake by primary macrophages and HepaRG cells was measured. In vitro cell viability evidenced a mild toxicity of the NPs only at high concentrations/densities of NPs in culture media. These data did not evidence a higher biocompatibility of the NPs prepared from enzymatic polymerization, and further demonstrated that chemical polymerization and the nanoprecipitation procedure led to biocompatible PMLABe-based NPs. In contrast, NPs produced from enzymatically synthesized polymers were more efficiently internalized than NPs produced from chemically synthesized polymers. The efficient uptake, combined with low cytotoxicity, indicate that PMLABe-based NPs are suitable nanovectors for drug delivery, deserving further evaluation in vivo to target either hepatocytes or resident liver macrophages.

A Surfactant Directed Microcrystalline Cellulose/Polyaniline Composite with Enhanced Electrochemical Properties

In this study a cationic surfactant, cetyltrimethylammonium bromide (CTAB), was used as a soft template for in situ chemical polymerization of aniline on the surface of microcrystalline cellulose (MCC). The morphology of the wire-like and porous nanostructure of the resulting composite was highly dependent on the MCC and CTAB concentrations. The effect of the MCC and CTAB concentrations on the electrochemical and morphological properties of the polyaniline (PAni) nanocomposite was studied. Cyclic voltammograms of modified PAni/MCC/CTAB electrode displayed a high current response and the effect of scan rate on the current response confirmed a diffusion controlled process on the surface of the electrode that makes it suitable for sensor applications. The overlapping characteristic peaks of pure PAni and MCC caused peak broadening at 3263 cm^-1 in the IR spectra of PAni/MCC/CTAB nanocomposite that revealed the interaction between NH of PAni and OH group of MCC via electrostatic interactions. The addition of MCC to PAni through chemical polymerization decreased the thermal stability of composite compared to pure PAni. Lower crystallinity was observed in the XRD diffractogram, with 2 theta values of 22.8, 16.5, and 34.6 for PAni/MCC, confirming the formation of PAni on the MCC surface.

Tuning the optical properties of poly(o-phenylenediamine-co-pyrrole) via template mediated copolymerization

Tailoring of conjugated monomers via copolymerization is a facile method to obtain tunable spectral, morphological and optical properties. To investigate the effect of copolymerization of pyrrole with o-phenylenediamine on the optoelectronic properties of the synthesized copolymers, the present work reports the synthesis of copolymers of o-phenylenediamine with pyrrole with varying mol ratios via chemical polymerization in methylene blue (MB) medium. Copolymerization was confirmed by Fourier transform infrared spectroscopy and ultraviolet-visible studies. Ultraviolet-visible spectroscopy revealed variation in the optical properties with the change in the monomer ratio. Fluorescence studies showed that the copolymer containing 80% poly(o-phenylenediamine) revealed highest quantum yield among all the copolymers. The emission color could therefore be tuned by careful selection of narrow band co-monomers, which could help in designing tunable fluorescence emitting materials for potential application in OLED devices.

Synergy Effect of Nanocrystalline Cellulose for the Biosensing Detection of Glucose

Integrating polypyrrole-cellulose nanocrystal-based composites with glucose oxidase (GOx) as a new sensing regime was investigated. Polypyrrole-cellulose nanocrystal (PPy-CNC)-based composite as a novel immobilization membrane with unique physicochemical properties was found to enhance biosensor performance. Field emission scanning electron microscopy (FESEM) images showed that fibers were nanosized and porous, which is appropriate for accommodating enzymes and increasing electron transfer kinetics. The voltammetric results showed that the native structure and biocatalytic activity of GOx immobilized on the PPy-CNC nanocomposite remained and exhibited a high sensitivity (ca. 0.73 μA·mM⁻¹), with a high dynamic response ranging from 1.0 to 20 mM glucose. The modified glucose biosensor exhibits a limit of detection (LOD) of (50 ± 10) µM and also excludes interfering species, such as ascorbic acid, uric acid, and cholesterol, which makes this sensor suitable for glucose determination in real samples. This sensor displays an acceptable reproducibility and stability over time. The current response was maintained over 95% of the initial value after 17 days, and the current difference measurement obtained using different electrodes provided a relative standard deviation (RSD) of 4.47%.