Preparation of PdNPs doped chitosan-based composite hydrogels as highly efficient catalysts for reduction of 4-nitrophenol

Cu-Fe embedded cross-linked 3D hydrogel for enhanced reductive removal of Cr(VI): Characterization, performance, and mechanisms

Porous hydrogel, as a high-efficiency adsorbent for heavy metals, suffers the drawbacks of the use of expensive and toxic reagents during the process of preparation, further limiting its application ranges. Besides, the heavy metals couldn't be transformed into nontoxic species, which leads to the environmental pollution risk. Herein, a three-dimensionally (3D) structured Cu-Fe embedded cross-linked cellulose hydrogel (nFeCu-CH) was innovatively fabricated by a novel self-assembly and in-situ reduction method, which exhibited exceptionally enhanced adsorption-reduction property towards Cr(VI) wastewater. The results of degradation experiment exhibited that the removal reaction followed Langmuir-Hinshelwood first order kinetic model and the degradation rate constant decreased with solution pH and initial Cr(VI) concentration, while increased with nFeCu-CH dosage and temperature. Regeneration studies demonstrated that more than 88% of Cr(VI) was removed by nFeCu-CH even after five times of cycling. nFeCu-CH exhibited excellent reductive activity, which had a close connection with the superiority of 3D crosslinked architectures and bimetallic synergistic effect. And 97.1% of Cr(VI) could be removed when nFeCu-CH dosage was 9.5 g/L, pH was 5, initial concentration of Cr(VI) was 20 mg/L and temperature was 303 K. Combined with cellulose hydrogel not only could provide additional active sites, but also could restrain the crystallite growth and agglomeration of nano-metallic particles, leading to the promotion of Cr(VI) removal. In addition, coating with Cu facilitated the generation and transformation of electrons according to the continuous redox cycles of Fe(III)/Fe(II) and Cu(II)/Cu(I), leading to the further improvement of the reductivity of nFeCu-CH. Multiple interaction mechanisms including adsorption, reduction and co-precipitation between nFeCu-CH and Cr(VI) were realized. The current work suggested that nFeCu-CH with highly reactive sites, excellent stability and recyclability was considered as an potential material for remediation of Cr(VI) contaminated wastewater.

Bioinspired, Recyclable, Stretchable Hydrogel with Boundary Ultralubrication

Although hydrogels exhibit excellent low frictional behavior, their friction coefficients cannot meet the requirements for biology, especially at low sliding velocities. Inspired by the natural lubrication mechanism from animals, plants, or even microorganisms, a nonionic surfactant, Tween 80, was introduced into a biofriendly poly(vinyl alcohol) (PVA) hydrogel to construct a composite hydrogel with ultralubrication. Such a combination endows PVA hydrogels with an ultralow coefficient of friction (10^-3 to 10^-4) under an extremely low sliding velocity (0.01 mm/s). Tween 80 micelles and aggregates, together with hydrophobic molds, induce rough surfaces and high carbon contents on the surface of the hydrogel, promoting excellent lubrication behavior of the composite hydrogel. In addition to the desirable lubrication, this environmentally friendly composite hydrogel also exhibited excellent flexibility at subzero temperatures, tensile properties, and good recyclability. Additionally, the method of introducing Tween 80 into hydrogels to reduce friction is also effective in chemically crosslinked double-network hydrogels.

Development of alginate@tin oxide-cobalt oxide nanocomposite based catalyst for the treatment of wastewater

In this study, tin oxide‑cobalt oxide nanocatalyst was prepared by a simple method, which grew in spherical particles with an average diameter of 30 nm. Tin oxide-cobalt oxide was further wrapped in alginate polymer hydrogel (Alg@tin oxide-cobalt oxide), and both materials were utilized as nanocatalysts for the catalytic transformation of different pollutants. Tin oxide-cobalt oxide and Alg@tin oxide-cobalt oxide nanocatalysts were tested for the catalytic reduction of 4-nitrophenol, congo red, methyl orange, methylene blue (MB) and potassium ferricyanide in which sodium borohydride was used as a reducing agent. Tin oxide-cobalt oxide and Alg@tin oxide-cobalt oxide nanocatalysts synergistically reduced MB in shorter time (2.0 and 4.0 min) compared to other dyes. The reduction conditions were optimized by changing different parameters. The rate constants for MB reduction were calculated and found to be 1.5714 min^-1 and 0.6033 min^-1 using tin oxide-cobalt oxide and Alg@tin oxide-cobalt oxide nanocatalysts, respectively. Implementing Alg@tin oxide-cobalt oxide nanocatalyst toward MB reduction in real samples proved its efficacy in sea and well water samples. The catalyst could be easily recovered, recycled and revealed a minimal loss of nanoparticles, which offering a competition and replacement with reputable commercial catalysts.

Chitosan based macromolecular probes for the selective detection and removal of Fe3+ ion

Chitosan has been widely used due to its biodegradable, cost-effective and environmentally friendly properties. Modification of chitosan attracts much attention as promising methods to detect and remove organic and inorganic pollutants. In this work, chitosan-based macromolecular probes were designed and synthesized. The probes can detect Fe³⁺ in the presence of other metal ions. The detection mechanism is investigated as well. The probe's fluorescence quenching upon the addition of Fe³⁺ ion could be ascribed to the complexation between the electron-deficient ion Fe³⁺ and "C=N" (electron-rich group) of fluorescent chitosan probes. What's more, the obtained fluorescent macromolecular probes can be used for the removal of Fe³⁺ in solution. The probes could adsorb the Fe³⁺ in solution and the removal efficiency can reach as high as 62.0% while the removal efficiency of original chitosan is only 16.0%. The probes have good selective detection for Fe³⁺ and the detection limit reaches 1.2 μM.

Cyclodextrin-Cross-Linked Hydrogels for Adsorption and Photodegradation of Cationic Dyes in Aqueous Solution

Possessing three-dimensional porous structures and tunable mechanical strengths, cyclodextrin-containing polymeric hydrogels are one of the most promising water-based adsorbent materials due to their easy availability, simple chemical modification and environmental friendliness. In this work, two kinds of hydrogels were prepared via the copolymerization with acrylic acid and vinyl-derivatized β-cyclodextrins in water. These two gels have showed good adsorption performance towards cationic dyes through the noncovalent interactions with their anionic backbones and porous network. Meanwhile, pseudo-second-order model was selected to clarify the adsorption kinetics process. Moreover, nano-scaled TiO₂ was doped into these resultant cyclodextrins-based hydrogels to achieve efficient degradation of dyes upon light irradiation. The obtained TiO₂ -loaded hydrogels could exhibit improved adsorption performance and make the adsorbed dyes photo-degraded with the decolorization rates above 95%. It can be envisioned that such cyclodextrin-based soft materials may find applications in dye clearance and water treatment.

Two Fascinating Polysaccharides: Chitosan and Starch. Some Prominent Characterizations for Applying as Eco-Friendly Food Packaging and Pollutant Remover in Aqueous Medium. Progress in Recent Years: A Review

The call to use biodegradable, eco-friendly materials is urgent. The use of biopolymers as a replacement for the classic petroleum-based materials is increasing. Chitosan and starch have been widely studied with this purpose: to be part of this replacement. The importance of proper physical characterization of these biopolymers is essential for the intended application. This review focuses on characterizations of chitosan and starch, approximately from 2017 to date, in one of their most-used applications: food packaging for chitosan and as an adsorbent agent of pollutants in aqueous medium for starch.

Inversing supramolecular chirality and boosting circularly polarized luminescence of pyrene moieties via a gel matrix

Alkyl-substituted l/d-glutamide derivatives (L/D-SG) were designed as gelators to fabricate host gel matrices. Pyrene-appended l/d-glutamide derivatives (Py-LG/Py-DG) were employed as guest luminophores to investigate chiral packing and emission behavior in gel matrices. It was found that Py-LG and Py-DG are prone to form P- and M-chirally packed assemblies in DMSO gels, respectively. However, the chiral packing was inversed, and CPL was boosted after Py-LG/Py-DG was embedded in the L/D-SG gel matrix. M-chiral packing together with left-handed excimer emission ((-)-CPL) was observed in the Py-LG immobilized L-SG gel matrix, while P-chiral packing together with right-handed excimer emission ((+)-CPL) was found in the Py-DG immobilized L-SG gel matrix. It is more interesting to find that the molecular chirality of the matrix gelator did not affect the supramolecular chirality of pyrene assemblies. Either l or a d-matrix gelator can inverse the supramolecular chirality of the pure gel, but did not follow the chirality of the matrix. It was found that the gel matrix converts intralayer pyrene-pyrene (Py-Py) packing in the pure pyrene gel to interlayer Py-Py packing, thus giving an opposite chirality. The study not only deepened our understanding of the supramolecular chirality transfer but also unveiled the effects of an inert gel matrix in regulating the chiroptical properties.

Three-Dimensional Network Pd-Ni/γ-Al2O3 Catalysts for Highly Active Catalytic Hydrogenation of Nitrobenzene to Aniline under Mild Conditions

In view of the current situation of high cost and low catalytic efficiency of the commercial Pd-based catalysts, adding transition metals (Ni, Co, etc.) to form the Pd-M bimetallic catalyst not only reduces the consumption of Pd but also greatly improves the catalytic activity and stability, which has attracted increasing attention. In this work, the three-dimensional network Pd-Ni bimetallic catalysts were prepared successfully by a liquid-phase in situ reduction method with the hydroxylated γ-Al₂O₃ as the support. Through investigating the effects of the precursor salt amount, reducing agent concentration, stabilizer concentration, and reducing stirring time on the synthesis of the Pd-Ni nanocatalyst, the three-dimensional network Pd-Ni bimetallic nanostructures with four different atomic ratios were prepared under an optimal condition. The obtained wire-like Pd-Ni catalysts have a uniform diameter size of about 5 nm and length up to several microns. After closely combining with the hydroxylated γ-Al₂O₃, the supported Pd-Ni/γ-Al₂O₃ catalysts exhibit nearly 100% conversion rate and selectivity for the hydrogenation of nitrobenzene to aniline at low temperature and normal pressure. The stability testing of the supported Pd-Ni/γ-Al₂O₃ catalysts shows that the conversion rate still remained above 99% after 10 cycles. There is no doubt that the supported catalysts show significant catalytic efficiency and recyclability, which provides important theoretical basis and technical support for the preparation of low-cost, highly efficient catalysts for the hydrogenation of nitrobenzene to aniline.

Construction of Nanocrystalline Cellulose-Based Composite Fiber Films with Excellent Porosity Performances via an Electrospinning Strategy

Cellulose nanocrystals (CNCs) not only have environmental protection characteristics of being lightweight, degradable, green, and renewable but also have some nanocharacteristics of high strength, large specific surface area, and obvious small size effect, so they are often used as a reinforcing agent in various polymers. However, the hydrogen bonding between CNC molecules is relatively strong, and they can easily aggregate and get entangled with each other. In this work, several large-porosity composite nanofiber films, KH550-CNC/waterborne polyurethane (WPU)/poly(vinyl alcohol) (PVAL) with KH550-modified CNCs, are prepared using poly(vinyl alcohol) (PVAL) solution and electrospinning technology. A variety of characterization methods are used to discuss and analyze the nanofiber materials, and the effects of the added amount of CNCs modified with KH550, spinning voltage, curing distance, and advancing speed on the morphology and performance of composite fibers are discussed separately. The results show that when the content of KH550-CNC is 1%, the composite fiber film obtained has the most regular morphology and the best spinnability, which is convenient for the specific application of fiber materials in a later period. In addition, the porosity of the obtained composite fiber film is 62.61%. Therefore, this work provides a theoretical basis and research strategy for the preparation of higher-porosity composite films as well as the development of new textile materials.

Synthesis of a New Amino-Furopyridine-Based Compound as a Novel Fluorescent pH Sensor in Aqueous Solution

Development of new fluorescent molecules, especially pH-sensitive fluorescent dyes, is always in high demand due to their wide applications in various fields and the limited number of common chromophores. In this work, a family of 3-amino-N-phenylfuro[2,3-b]pyridine-2-carboxamides (AFP) was synthesized as novel fluorescent compounds. Besides fluorescence in an organic solvent, AFP 1 and AFP 2 exhibit good fluorescence properties in both acidic and basic aqueous solution, which could be explained by protonation or different conformations formed in solution. Density functional theory (DFT) calculations on the highest occupied molecular orbital-lowest unoccupied molecular orbital (HOMO-LUMO) of various conformations were performed for further support.

Self-Assembled Black Phosphorus-Based Composite Langmuir-Blodgett Films with an Enhanced Photocurrent Generation Capability and Surface-Enhanced Raman Scattering Properties

In this work, Langmuir-Blodgett (LB) composite thin films were successfully prepared using black phosphorus nanosheets (BPNS) and dye molecules. Black phosphorus (BP) was first exfoliated in isopropanol solution to form BPNS, and then, BPNS were modified with 4-azidobenzoic acid (Az-BPNS) to improve their stability. The characterization results showed that the synthesized Az-BPNS-dye LB films have a uniform and ordered structure. In addition, the synthesized Az-BPNS-dye LB films exhibit excellent photoelectrochemical performance, and Az-BPNS-methylene blue (MB) produces higher photocurrent compared to Az-BPNS-Neutral red (NR) films. The current work shows an effective way to prepare functionalized BP-based materials and provide evidence for their application in optoelectronic devices.

3D Printing in Development of Nanomedicines

Three-dimensional (3D) printing is gaining numerous advances in manufacturing approaches both at macro- and nanoscales. Three-dimensional printing is being explored for various biomedical applications and fabrication of nanomedicines using additive manufacturing techniques, and shows promising potential in fulfilling the need for patient-centric personalized treatment. Initial reports attributed this to availability of novel natural biomaterials and precisely engineered polymeric materials, which could be fabricated into exclusive 3D printed nanomaterials for various biomedical applications as nanomedicines. Nanomedicine is defined as the application of nanotechnology in designing nanomaterials for different medicinal applications, including diagnosis, treatment, monitoring, prevention, and control of diseases. Nanomedicine is also showing great impact in the design and development of precision medicine. In contrast to the "one-size-fits-all" criterion of the conventional medicine system, personalized or precision medicines consider the differences in various traits, including pharmacokinetics and genetics of different patients, which have shown improved results over conventional treatment. In the last few years, much literature has been published on the application of 3D printing for the fabrication of nanomedicine. This article deals with progress made in the development and design of tailor-made nanomedicine using 3D printing technology.

Self-Assembled Sandwich-like MXene-Derived Composites as Highly Efficient and Sustainable Catalysts for Wastewater Treatment

Photocatalysts play an increasingly important role in environmental remediation polluted by industrial wastewater. However, the preparation of adsorbents and catalysts with high activity by simple and easy methods is still a great challenge. Here, sandwich-like composite catalyst Cu₂O/TiO₂/Ti₃C₂ was prepared by an easily available solvent reduction measure for the highly efficient catalytic nitro compounds. In particular, sandwich-like composite catalyst Cu₂O/TiO₂/Ti₃C₂ exhibits excellent catalysis for 2-nitroaniline (2-NA) and 4-nitrophenol (4-NP), and its pseudo-first-order reaction rate constants (k) are 0.163 and 0.114 min^-1, respectively. Interestingly, even after eight consecutive cycles of catalytic experiments, the conversion rates of catalytic 2-NA and 4-NP are still greater than 95 and 92%, respectively, demonstrating that the obtained catalyst has excellent catalytic capability and a high reutilization rate. The excellent catalytic performances of Cu₂O/TiO₂/Ti₃C₂ can be attributed to the fact that Ti₃C₂ provides a greater reaction site for the formation of Cu₂O and reduces the aggregation during the formation of Cu₂O by in situ synthesis. Therefore, ternary composite catalyst Cu₂O/TiO₂/Ti₃C₂ prepared by solvent reduction not only supplies a technical method for the catalytic reaction of MXene-based material but also lays the foundation for the development of new photocatalysts.

Subtle influence on alginate gel properties through host–guest interactions between covalently appended cyclodextrin and adamantane units

Host–guest interactions between functionalized alginate chains modulate the physico-chemical properties of alginate gels.