Magnetic resonance thermometry and its biological applications - Physical principles and practical considerations

Assessing critical temperature dose areas in the kidney by magnetic resonance imaging thermometry in an ex vivo Holmium:YAG laser lithotripsy model

PURPOSE

We aimed to assess critical temperature areas in the kidney parenchyma using magnetic resonance thermometry (MRT) in an ex vivo Holmium:YAG laser lithotripsy model.

METHODS

Thermal effects of Ho:YAG laser irradiation of 14 W and 30 W were investigated in the calyx and renal pelvis of an ex vivo kidney with different laser application times (t_L) followed by a delay time (t_D) of t_L/t_D = 5/5 s, 5/10 s, 10/5 s, 10/10 s, and 20/0 s, with irrigation rates of 10, 30, 50, 70, and 100 ml/min. Using MRT, the size of the area was determined in which the thermal dose as measured by the Cumulative Equivalent Minutes (CEM₄₃) method exceeded a value of 120 min.

RESULTS

In the calyx, CEM₄₃ never exceeded 120 min for flow rates ≥ 70 ml/min at 14 W, and longer t_L (10 s vs. 5 s) lead to exponentially lower thermal affection of tissue (3.6 vs. 21.9 mm²). Similarly at 30 W and ≥ 70 ml/min CEM₄₃ was below 120 min. Interestingly, at irrigation rates of 10 ml/min, t_L = 10 s and t_D = 10 s CEM₄₃ were observed > 120 min in an area of 84.4 mm² and 49.1 mm² at t_D = 5 s. Here, t_L = 5 s revealed relevant thermal affection of 29.1 mm² at 10 ml/min.

CONCLUSION

We demonstrate that critical temperature dose areas in the kidney parenchyma were associated with high laser power and application times, a low irrigation rate, and anatomical volume of the targeted calyx.

Iron-based coupling media for MRI-guided ultrasound surgery

PURPOSE

In this study, we examine the effects of a recently developed, iron-based coupling medium (IBCM) on guidance magnetic resonance (MR) scans during transcranial, magnetic-resonance-guided, focused ultrasound surgery (tMRgFUS) procedures. More specifically, this study tests the hypotheses that the use of the IBCM will (a) not adversely affect image quality, (b) remove aliasing from small field-of-view scans, and (c) decouple image quality from the motion state of the coupling fluid.

METHODS

An IBCM, whose chemical synthesis and characterization are reported elsewhere, was used as a coupling medium during tMRgFUS procedures on gel phantoms. Guidance magnetization-prepared rapid-gradient-echo (MP-RAGE), TSE, and GRE scans were acquired with fields of view of 28 and 18 cm. Experiments were repeated with the IBCM in several distinct flow states. GRE scans were used to estimate temperature time courses as a gel target was insonated. IBCM performance was measured by computing (i) the root mean square difference (RMSD) of TSE and GRE pixel values acquired using water and the IBCM, relative to the use of water; (ii) through-time temperature uncertainty for GRE scans; and (iii) Bland-Altman analysis of the temperature time courses. Finally, guidance TSE and GRE scans of a human volunteer were acquired during a separate sham tMRgFUS procedure. As a control, all experiments were repeated using a water coupling medium.

RESULTS

Use of the IBCM reduced RMSD in TSE scans by a factor of 4 or more for all fields of view and nonstationary motion states, but did not reduce RMSD estimates in MP-RAGE scans. With the coupling media in a stationary state, the IBCM altered estimates of temperature uncertainty relative to the use of water by less than 0.2°C. However, with a high flow state, the IBCM reduced temperature uncertainties by the statistically significant amounts (at the 0.01 level) of 0.5°C (28 cm field of view) and 5°C (18 cm field of view). Bland-Altman analyses found a 0.1°C ± 0.5°C difference between temperature estimates acquired using water and the IBCM as coupling media. Finally, scans of a human volunteer using the IBCM indicate more conspicuous grey/white matter contrast, a reduction in aliasing, and a less than 0.2°C change in temperature uncertainty.

CONCLUSIONS

The use of an IBCM during tMRgFUS procedures does not adversely affect image quality for TSE and GRE scans, can decouple image quality from the motion state of the coupling fluid, and can remove aliasing from scans where the field of view is set to be much smaller than the spatial extent of the coupling fluid.

Recent Advances in Metal-Organic Frameworks for Applications in Magnetic Resonance Imaging

Diagnostics is an important part of medical practice. The information required for diagnosis is typically collected by performing diagnostic tests, some of which include imaging. Magnetic resonance imaging (MRI) is one of the most widely used and effective imaging techniques. To improve the sensitivity and specificity of MRI, contrast agents are used. In this review, the usage of metal-organic frameworks (MOFs) and composite materials based on them as contrast agents for MRI is discussed. MOFs are crystalline porous coordination polymers. Due to their huge design variety and high density of metal ions, they have been studied as a highly promising class of materials for developing MRI contrast agents. This review highlights the most important studies and focuses on the progress of the field over the last five years. The materials are classified based on their design and structural properties into three groups: MRI-active MOFs, composite materials based on MOFs, and MRI-active compounds loaded in MOFs. Moreover, an overview of MOF-based materials for heteronuclear MRI including 129Xe and 19F MRI is given.

Validating a simulation model for laser-induced thermotherapy using MR thermometry

OBJECTIVES

We want to investigate whether temperature measurements obtained from MR thermometry are accurate and reliable enough to aid the development and validation of simulation models for Laser-induced interstitial thermotherapy (LITT).

METHODS

Laser-induced interstitial thermotherapy (LITT) is applied to ex-vivo porcine livers. An artificial blood vessel is used to study the cooling effect of large blood vessels in proximity to the ablation zone. The experimental setting is simulated using a model based on partial differential equations (PDEs) for temperature, radiation, and tissue damage. The simulated temperature distributions are compared to temperature data obtained from MR thermometry.

RESULTS

The overall agreement between measurement and simulation is good for two of our four test cases, while for the remaining cases drift problems with the thermometry data have been an issue. At higher temperatures local deviations between simulation and measurement occur in close proximity to the laser applicator and the vessel. This suggests that certain aspects of the model may need some refinement.

CONCLUSION

Thermometry data is well-suited for aiding the development of simulations models since it shows where refinements are necessary and enables the validation of such models.

Evaluation method of ex vivo porcine liver reduced scattering coefficient during microwave ablation based on temperature

The principle of microwave ablation (MWA) is to cause irreversible damage (protein coagulation, necrosis, etc.) to tumor cells at a certain temperature by heating, thereby destroying the tumor. We have long used functional near-infrared spectroscopy (fNIRs) to monitor clinical thermal ablation efficacy. After a lot of experimental verification, it can be found that there is a clear correlation between the reduced scattering coefficient and the degree of tissue damage. During the MWA process, the reduced scattering coefficient has a stable change. Therefore, both temperature (T) and reduced scattering coefficient ( μ s ′ ${\mu }_{s}^{\prime }$ ) are related to the thermal damage of the tissue. This paper mainly studies the changing law of T and μ s ′ ${\mu }_{s}^{\prime }$ during MWA and establishes a relationship model. The two-parameter simultaneous acquisition system was designed and used to obtain the T and μ s ′ ${\mu }_{s}^{\prime }$ of the ex vivo porcine liver during MWA. The correlation model between T and μ s ′ ${\mu }_{s}^{\prime }$ is established, enabling the quantitative estimation of μ s ′ ${\mu }_{s}^{\prime }$ of porcine liver based on T. The maximum and the minimum relative errors of μ s ′ ${\mu }_{s}^{\prime }$ are 79.01 and 0.39%, respectively. Through the electromagnetic simulation of the temperature field during MWA, 2D and 3D fields of reduced scattering coefficient can also be obtained using this correlation model. This study contributes to realize the preoperative simulation of the optical parameter field of microwave ablation and provide 2D/3D therapeutic effect for clinic.

Improving the reproducibility of proton magnetic resonance spectroscopy brain thermometry: Theoretical and empirical approaches

In proton magnetic resonance spectroscopy (¹ H MRS)-based thermometry of brain, averaging temperatures measured from more than one reference peak offers several advantages, including improving the reproducibility (i.e., precision) of the measurement. This paper proposes theoretically and empirically optimal weighting factors to improve the weighted average of temperatures measured from three references. We first proposed concepts of equivalent noise and equivalent signal-to-noise ratio in terms of frequency measurement and a concept of relative frequency that allows the combination of different peaks in a spectrum for improving the precision of frequency measurement. Based on these, we then derived a theoretically optimal weighting factor and proposed an empirical weighting factor, both involving equivalent noise levels, for a weighted average of temperatures measured from three references (i.e., the singlets of NAA, Cr, and Ch in the ¹ H MR spectrum). We assessed these two weighting factors by comparing their errors in measurement of temperatures with the errors of temperatures measured from individual references; we also compared these two new weighting factors with two previously proposed weighting factors. These errors were defined as the standard deviations in repeated measurements or in Monte Carlo studies. Both the proposed theoretical and empirical weighting factors outperformed the two previously proposed weighting factors as well as the three individual references in all phantom and in vivo experiments. In phantom experiments with 4- or 10-Hz line broadening, the theoretical weighting factor outperformed the empirical one, but the latter was superior in all other repeated and Monte Carlo tests performed on phantom and in vivo data. The proposed weighting factors are superior to the two previously proposed weighting factors and can improve the reproducibility of temperature measurement using ¹ H MRS-based thermometry.

Luminescence Thermometry for Brain Activity Monitoring: A Perspective

Minimally invasive monitoring of brain activity is essential not only to gain understanding on the working principles of the brain, but also for the development of new diagnostic tools. In this perspective we describe how brain thermometry could be an alternative to conventional methods (e.g., magnetic resonance or nuclear medicine) for the acquisition of thermal images of the brain with enough spatial and temperature resolution to track brain activity in minimally perturbed animals. We focus on the latest advances in transcranial luminescence thermometry introducing a critical discussion on its advantages and shortcomings. We also anticipate the main challenges that the application of luminescent nanoparticles for brain thermometry will face in next years. With this work we aim to promote the development of near infrared luminescence for brain activity monitoring, which could also benefit other research areas dealing with the brain and its illnesses.

Correlation Analysis of TSB Level and Globus Pallidus-Related Metabolite Indexes of Proton Magnetic Resonance Spectroscopy in the Newborn with Neonatal Jaundice

Objective

To investigate the correlation between serum total serum bilirubin (TSB) levels and globus pallidus-related metabolic indexes of proton magnetic resonance spectroscopy (1H-MRS) in the newborn with neonatal jaundice.

Methods

50 children with neonatal jaundice admitted to our hospital from January 2019 to January 2021 were recruited and assigned to a mild condition group (TSB < 221 μmol/L, n = 16), a moderate condition group (221 μmol/L ≤ TSB < 3 42 μmol/L, n = 18), and a severe condition group (342 μmol/L ≤ TSB < 428 μmol/L, n = 16) based on peak TSB. The differences in globus pallidus-related metabolic indexes of 1H-MRS between the groups were compared and their correlation with TSB levels was analyzed.

Results

The three groups had comparable N-acetylaspartic acid (NAA)/creatine (Cr), choline (Cho)/Cr, lactic acid (Lac)/Cr, and ml/Cr levels (P > 0.05), while there were statistical differences in glutamine (Glx)/Cr levels (P < 0.05). The severe condition group showed the highest levels of neuron-specific enolase (NSE), creatine kinase-MB (CK-MB), and troponin (cTnl), followed by the moderate group, and then the mild group (P < 0.05). The TSB level is positively correlated with the 1H-MRS metabolic index Glx/Cr.

Conclusions

The serum TSB level is correlated with the 1H-MRS metabolic index Glx/Cr in the newborn with neonatal jaundice, and the levels of TSB and Glx/Cr provide a reference for the diagnosis of bilirubin encephalopathy.

Analysis of cavitation artifacts in Magnetic Resonance Imaging Thermometry during laser ablation monitoring

Magnetic Resonance Thermometry Imaging (MRTI) holds great potential in laser ablation (LA) monitoring. It provides the real-time multidimensional visualization of the treatment effect inside the body, thus enabling accurate intraoperative prediction of the thermal damage induced. Despite its great potential., thermal maps obtained with MRTI may be affected by numerous artifacts. Among the sources of error producing artifacts in the images., the cavitation phenomena which could occur in the tissue during LA induces dipole-structured artifacts. In this work., an analysis of the cavitation artifacts occurring during LA in a gelatin phantom in terms of symmetry in space and symmetry of temperature values was performed. Results of 2 Wand 4 W laser power were compared finding higher symmetry for the 2 W case in terms of both dimensions of artifact-lobes and difference in temperature values extracted in specular pixels in the image. This preliminary investigation of artifact features may provide a step forward in the identification of the best strategy to correct and avoid artifact occurrence during thermal therapy monitoring. Clinical Relevance- This work presents an analysis of cavitation artifacts in MRTI from LA which must be corrected to avoid error in the prediction of thermal damage during LA monitoring.

Feasibility of ultrasound tomography-guided localized mild hyperthermia using a ring transducer: Ex vivo and in silico studies

BACKGROUND

As of 2022, breast cancer continues to be the most diagnosed cancer worldwide. This problem persists within the United States as well, as the American Cancer Society has reported that ∼12.5% of women will be diagnosed with invasive breast cancer over the course of their lifetime. Therefore, a clinical need continues to exist to address this disease from a treatment and therapeutic perspective. Current treatments for breast cancer and cancers more broadly include surgery, radiation, and chemotherapy. Adjuncts to these methods have been developed to improve the clinical outcomes for patients. One such adjunctive treatment is mild hyperthermia therapy (MHTh), which has been shown to be successful in the treatment of cancers by increasing effectiveness and reduced dosage requirements for radiation and chemotherapies. MHTh-assisted treatments can be performed with invasive thermal devices, noninvasive microwave induction, heating and recirculation of extracted patient blood, or whole-body hyperthermia with hot blankets.

PURPOSE

One common method for inducing MHTh is by using microwave for heat induction and magnetic resonance imaging for temperature monitoring. However, this leads to a complex, expensive, and inaccessible therapy platform. Therefore, in this work we aim to show the feasibility of a novel all-acoustic MHTh system that uses focused ultrasound (US) to induce heating while also using US tomography (UST) to provide temperature estimates. Changes in sound speed (SS) have been shown to be strongly correlated with temperature changes and can therefore be used to indirectly monitor heating throughout the therapy. Additionally, these SS estimates allow for heterogeneous SS-corrected phase delays when heating complex and heterogeneous tissue structures.

METHODS

Feasibility to induce localized heat in tissue was investigated in silico with a simulated breast model, including an embedded tumor using continuous wave US. Here, both heterogenous acoustic and thermal properties were modeled in addition to blood perfusion. We further demonstrate, with ex vivo tissue phantoms, the feasibility of using ring-based UST to monitor temperature by tracking changes in SS. Two phantoms (lamb tissue and human abdominal fat) with latex tubes containing varied temperature flowing water were imaged. The measured SS of the water at each temperature were compared against values that are reported in literature.

RESULTS

Results from ex vivo tissue studies indicate successful tracking of temperature under various phantom configurations and ranges of water temperature. The results of in silico studies show that the proposed system can heat an acoustically and thermally heterogenous breast model to the clinically relevant temperature of 42°C while accounting for a reasonable time needed to image the current cross section (200 ms). Further, we have performed an initial in silico study demonstrating the feasibility of adjusting the transmit waveform frequency to modify the effective heating height at the focused region. Lastly, we have shown in a simpler 2D breast model that MHTh level temperatures can be maintained by adjusting the transmit pressure intensity of the US ring.

CONCLUSIONS

This work has demonstrated the feasibility of using a 256-element ring array transducer for temperature monitoring; however, future work will investigate minimizing the difference between measured SS and the values shown in literature. A hypothesis attributes this bias to potential volumetric average artifacts from the ray-based SS inversion algorithm that was used, and that moving to a waveform-based SS inversion algorithm will greatly improve the SS estimates. Additionally, we have shown that an all-acoustic MHTh system is feasible via in silico studies. These studies have indicated that the proposed system can heat a tumor within a heterogenous breast model to 42°C within a narrow time frame. This holds great promise for increasing the accessibility and reducing the complexity of a future all-acoustic MHTh system.

In Vivo Magnetic Resonance Thermometry for Brain and Body Temperature Variations in Canines under General Anesthesia

The core body temperature tends to decrease under general anesthesia. Consequently, monitoring the core body temperature during procedures involving general anesthesia is essential to ensure patient safety. In veterinary medicine, rectal temperature is used as an indicator of the core body temperature, owing to the accuracy and convenience of this approach. Some previous studies involving craniotomy reported differences between the brain and core temperatures under general anesthesia. However, noninvasive imaging techniques are required to ascertain this because invasive brain temperature measurements can cause unintended temperature changes by inserting the temperature sensors into the brain or by performing the surgical operations. In this study, we employed in vivo magnetic resonance thermometry to observe the brain temperatures of patients under general anesthesia using the proton resonance frequency shift method. The rectal temperature was also recorded using a fiber optic thermometer during the MR thermometry to compare with the brain temperature changes. When the rectal temperature decreased by 1.4 ± 0.5 °C (mean ± standard deviation), the brain temperature (white matter) decreased by 4.8 ± 0.5 °C. Furthermore, a difference in the temperature reduction of the different types of brain tissue was observed; the reduction in the temperature of white matter exceeded that of gray matter mainly due to the distribution of blood vessels in the gray matter. We also analyzed and interpreted the core temperature changes with the body conditioning scores of subjects to see how the body weight affected the temperature changes.

DWI-based MR thermometry: could it discriminate Alzheimer's disease from mild cognitive impairment and healthy subjects?

PURPOSE

The aim of this study is to compare lateral ventricular cerebrospinal fluid (CSF) temperature of the patients with Alzheimer's disease (AD), mild cognitive impairment (MCI), and healthy subjects (HS) using diffusion-weighted imaging (DWI)-based magnetic resonance (MR) thermometry.

METHODS

Seventy-two patients (37 AD, 19 MCI, 16 HS) who underwent 3-T MR examination from September 2018 to August 2019 were included in this study. Smoking habits, education level, disease duration, and comorbidity status were recorded. Patients were assessed using Mini-Mental State Examination (MMSE) and the Clinical Dementia Rating (CDR) score. Brain temperatures were measured using DWI-based MR thermometry. Group comparisons of brain temperature were performed using the Pearson chi-square, Mann-Whitney, and Kruskal-Wallis tests. Further analysis was performed using the post hoc Bonferroni test. Receiver operating characteristic (ROC) analysis was also used.

RESULTS

A CDR score of 0.5, 1, and 2 was 2 (5.4%), 14 (37.8%), and 21 (56.8%) in AD, respectively. The median MMSE score had significant differences among groups and also in pairwise comparisons. The median CSF temperature (°C) values showed statistically significant difference among groups (HS: 38.5 °C, MCI: 38.17 °C, AD: 38.0 °C). The post hoc Mann-Whitney U test indicated a significant difference between AD patients and HS (p = 0.009). There were no significant CSF temperature differences in other pairwise comparisons.

CONCLUSION

Lower CSF temperatures were observed in AD patients than in HS, probably due to decreased brain metabolism in AD. DWI-based MR thermometry as a noninvasive imaging method enabling the measurement of CSF temperatures may contribute to the diagnosis of AD.

The importance, status, and perspectives of hybrid lanthanide-doped upconversion nanothermometers for theranostics

Theranostics combines diagnostics and therapy in a single multifunctional system. Multifunctional upconversion luminescent lanthanide-doped nanothermometers for theranostic purposes offer non-invasive and sensitive multimodal performance in the biomedical field over traditional temperature measurement methods. Despite existing challenges, various studies on hybrid upconversion nanothermometers show substantial progress for (bio)imaging, temperature sensing, photodynamic and photothermal therapy, as well as drug delivery applications. The beauty of such an approach is that it unfolds possibilities to combine diagnostics and therapy in a single particle, which can modify the way certain diseases are treated, hence change the entire healthcare scene.

Continuous cardiac thermometry via simultaneous catheter tracking and undersampled radial golden angle acquisition for radiofrequency ablation monitoring

The complexity of the MRI protocol is one of the factors limiting the clinical adoption of MR temperature mapping for real-time monitoring of cardiac ablation procedures and a push-button solution would ease its use. Continuous gradient echo golden angle radial acquisition combined with intra-scan motion correction and undersampled temperature determination could be a robust and more user-friendly alternative than the ultrafast GRE-EPI sequence which suffers from sensitivity to magnetic field susceptibility artifacts and requires ECG-gating. The goal of this proof-of-concept work is to establish the temperature uncertainty as well as the spatial and temporal resolutions achievable in an Agar-gel phantom and in vivo using this method. GRE radial golden angle acquisitions were used to monitor RF ablations in a phantom and in vivo in two sheep hearts with different slice orientations. In each case, 2D rigid motion correction based on catheter micro-coil signal, tracking its motion, was performed and its impact on the temperature imaging was assessed. The temperature uncertainty was determined for three spatial resolutions (1 × 1 × 3 mm³, 2 × 2 × 3 mm³, and 3 × 3 × 3 mm³) and three temporal resolutions (0.48, 0.72, and 0.97 s) with undersampling acceleration factors ranging from 2 to 17. The combination of radial golden angle GRE acquisition, simultaneous catheter tracking, intra-scan 2D motion correction, and undersampled thermometry enabled temperature monitoring in the myocardium in vivo during RF ablations with high temporal (< 1 s) and high spatial resolution. The temperature uncertainty ranged from 0.2 ± 0.1 to 1.8 ± 0.2 °C for the various temporal and spatial resolutions and, on average, remained superior to the uncertainty of an EPI acquisition while still allowing clinical monitoring of the RF ablation process. The proposed method is a robust and promising alternative to EPI acquisition to monitor in vivo RF cardiac ablations. Further studies remain required to improve the temperature uncertainty and establish its clinical applicability.

Model-Based Thermometry for Laser Ablation Procedure Using Kalman Filters and Sparse Temperature Measurements

In this work, we implement a data-assimilation Bayesian framework for the reconstruction of the spatiotemporal profile of the tissue temperature during laser irradiation. The predictions of a physical model simulating the heat transfer in the tissue are associated with sparse temperature measurements, using an Unscented Kalman Filter. We compare a standard state-estimation filtering procedure with a joint-estimation (state and parameters) approach: whereas in the state-estimation only the temperature is evaluated, in the joint-estimation the filter corrects also uncertain model parameters (i.e., the medium thermal diffusivity, and laser beam properties). We have tested the method on synthetic temperature data, and on the temperature measured on agar-gel phantom and porcine liver with fiber optic sensors. The joint-estimation allows retrieving an accurate estimate of the temperature distribution with a maximal error < 1.5 C in both synthetic and liver 1D data, and < 2 C in phantom 2D data. Our approach allows also suggesting a strategy for optimizing the temperature estimation based on the positions of the sensors. Under the constraint of using only two sensors, optimal temperature estimations are obtained when one sensor is placed in proximity of the source, and the other one is in a non-symmetrical position.

Effects of T2 * on accuracy and precision of dynamic T1 measurements using the single reference variable flip angle method - a simulation study

PURPOSE

To study in simulation and in theory the accuracy and precision of dynamic T₁ measurements obtained using the previously published single-reference variable flip angle (SR-VFA) technique, with a focus on the effects of dynamic changes in T₂ * on the calculation.

METHODS

Monte Carlo simulations were performed over 1000 noisy iterations for the VFA method, the SR-VFA method, and a proposed method, SR-VFA with a T₂ * correction (SR-VFA-T₂ *). Dynamic T₁ estimates were calculated analytically for each method, with signals modeled by the steady-state spoiled gradient echo equation. The mean and standard deviation of these estimates were calculated and compared to truth, while varying repetition time (TR), baseline and dynamic T₁ , echo time (TE), baseline and dynamic T₂ *, flip angles, and the number of averages on baseline scans. Additionally, the variance of T₁ in the SR-VFA and SR-VFA-T₂ * methods was derived analytically based on the theory of propagation of errors. This equation was used to produce an inverse-variance weighted linear combination to improve T₁ mapping precision in the SR-VFA-T₂ * method. Flip angle sensitivity of dynamic T₁ precision in the SR-VFA and SR-VFA-T₂ * methods was also performed.

RESULTS

Substantial bias can be produced by the SR-VFA method when the ratio of the T₂ * decay of the dynamic signal versus that of the baseline signals deviates from 1, with a 0.01 deviation leading to approximately a 1% bias in cases of high SNR and TR ≫ T₁ . This bias can be corrected by estimating the baseline and dynamic T₂ * values in this ratio via multi-echo measurements. The bias and precision of the SR-VFA-T₂ * method, when normalized to scan time, is found to rival and sometimes improve upon the two flip angle VFA method when an inverse variance weighted linear combination is applied across its multi-echo T₁ maps. The analytic variance equation presented is found to be accurate within 1% relative to the Monte Carlo simulations over a broad parameter space. Flip angle ranges that maximize SR-VFA and SR-VFA-T₂ * T₁ precision over a broad parameter space are given, and each is defined relative to TR and T₁ .

CONCLUSIONS

Multi-echo SR-VFA-T₂ * T₁ mapping is found in simulation and theory to be a promising alternative to the VFA method that maintains speed of the SR-VFA method with accuracy and precision similar to the VFA method. This article is protected by copyright. All rights reserved.

Biological thermometer based on the temperature sensitivity of magnetic nanoparticle paraSHIFT

In the paper, the temperature dependence of magnetic nanoparticle (MNP) paramagnetic chemical shift (paraSHIFT) was studied by magnetic resonance (MR) spectroscopy. Based on it, iron oxide MNPs are considered as MR shifting probes for determining the temperature in liquids. With the increase in measurement temperature of the MNP reagent with MNPs, the decrease of MNP magnetization would make the peak of spectroscopy shift to the higher chemical shift area. The peak shift is related to the magnetic susceptibility of MNPs, which can be determined by MR frequency as a function of temperature and particle size. Experiments on temperature-dependent chemical shifts are performed for MNP samples with different core sizes and the estimated temperature accuracy can achieve 0.1 K. Combined with the contrast effect of magnetic nanoparticles in magnetic resonance imaging at 3 T, this technology can realize temperature imaging.

Interleaved water and fat MR thermometry for monitoring high intensity focused ultrasound ablation of bone lesions

PURPOSE

To demonstrate that interleaved MR thermometry can monitor temperature in water and fat with adequate temporal resolution. This is relevant for high intensity focused uUltrasounds (HIFU) treatment of bone lesions, which are often found near aqueous tissues, as muscle, or embedded in adipose tissues, as subcutaneous fat and bone marrow.

METHODS

Proton resonance frequency shift (PRFS)-based thermometry scans and T1 -based 2D variable flip angle (2D-VFA) thermometry scans were acquired alternatingly over time. Temperature in water was monitored using PRFS thermometry, and in fat by 2D-VFA thermometry with slice profile effect correction. The feasibility of interleaved water/fat temperature monitoring was studied ex vivo in porcine bone during MR-HIFU sonication. Precision and stability of measurements in vivo were evaluated in a healthy volunteer under non-heating conditions.

RESULTS

The method allowed observing temperature change over time in muscle and fat, including bone marrow, during MR-HIFU sonication, with a temporal resolution of 6.1 s. In vivo, the apparent temperature change was stable on the time scale of the experiment: In 7 min the systematic drift was <0.042°C/min in muscle (PRFS after drift correction) and <0.096°C/min in bone marrow (2D-VFA). The SD of the temperature change averaged over time was 0.98°C (PRFS) and 2.7°C (2D-VFA).

CONCLUSIONS

Interleaved MR thermometry allows temperature measurements in water and fat with a temporal resolution high enough for monitoring HIFU ablation. Specifically, combined fat and water thermometry provides uninterrupted information on temperature changes in tissue close to the bone cortex.

Recent Developments in Diagnosis of Epilepsy: Scope of MicroRNA and Technological Advancements

Epilepsy is one of the most common neurological disorders, characterized by recurrent seizures, resulting from abnormally synchronized episodic neuronal discharges. Around 70 million people worldwide are suffering from epilepsy. The available antiepileptic medications are capable of controlling seizures in around 60-70% of patients, while the rest remain refractory. Poor seizure control is often associated with neuro-psychiatric comorbidities, mainly including memory impairment, depression, psychosis, neurodegeneration, motor impairment, neuroendocrine dysfunction, etc., resulting in poor prognosis. Effective treatment relies on early and correct detection of epileptic foci. Although there are currently a few well-established diagnostic techniques for epilepsy, they lack accuracy and cannot be applied to patients who are unsupportive or harbor metallic implants. Since a single test result from one of these techniques does not provide complete information about the epileptic foci, it is necessary to develop novel diagnostic tools. Herein, we provide a comprehensive overview of the current diagnostic tools of epilepsy, including electroencephalography (EEG) as well as structural and functional neuroimaging. We further discuss recent trends and advances in the diagnosis of epilepsy that will enable more effective diagnosis and clinical management of patients.

Measurement of sub-zero temperatures in MRI using T1 temperature sensitive soft silicone materials: Applications for MRI-guided cryosurgery

PURPOSE

One standard method, proton resonance frequency shift, for measuring temperature using magnetic resonance imaging (MRI), in MRI-guided surgeries, fails completely below the freezing point of water. Because of this, we have developed a new methodology for monitoring temperature with MRI below freezing. The purpose of this paper is to show that a strong temperature dependence of the nuclear relaxation time T₁ in soft silicone polymers can lead to temperature-dependent changes of MRI intensity acquired with T₁ weighting. We propose the use of silicone filaments inserted in tissue for measuring temperature during MRI-guided cryoablations.

METHODS

The temperature dependence of T₁ in bio-compatible soft silicone polymers was measured using nuclear magnetic resonance spectroscopy and MRI. Phantoms, made of bulk silicone materials and put in an MRI-compatible thermal container with dry ice, allowed temperature measurements ranging from -60°C to + 20°C. T₁ -weighted gradient echo images of the phantoms were acquired at spatially uniform temperatures and with a gradient in temperature to determine the efficacy of using these materials as temperature indicators in MRI. Ex vivo experiments on silicone rods, 4 mm in diameter, inserted in animal tissue were conducted to assess the practical feasibility of the method.

RESULTS

Measurements of nuclear relaxation times of protons in soft silicone polymers show a monotonic, nearly linear, change with temperature (R²  > 0.98) and have a significant correlation with temperature (Pearson's r > 0.99, p < 0.01). Similarly, the intensity of the MR images in these materials, taken with a gradient echo sequence, are also temperature dependent. There is again a monotonic change in MRI intensity that correlates well with the measured temperature (Pearson's r < -0.98 and p < 0.01). The MRI experiments show that a temperature change of 3°C can be resolved in a distance of about 2.5 mm. Based on MRI images and external sensor calibrations for a sample with a gradient in temperature, temperature maps with 3°C isotherms are created for a bulk phantom. Experiments demonstrate that these changes in MRI intensity with temperature can also be seen in 4 mm silicone rods embedded in ex vivo animal tissue.

CONCLUSIONS

We have developed a new method for measuring temperature in MRI that potentially could be used during MRI-guided cryoablation operations, reducing both procedure time and cost, and making these surgeries safer.

Proton resonance frequency-based thermometry for aqueous and adipose tissues

PURPOSE

The proton resonance frequency (PRF)-based thermometry uses heating-induced phase variations to reconstruct magnetic resonance (MR) temperature maps. However, the measurements of the phase differences may be corrupted by the presence of fat due to its phase being insensitive to heat. The work aims to reconstruct the PRF-based temperature maps for tissues containing fat.

METHODS

This work proposes a PRF-based method that eliminates the fat's phase contribution by estimating the temperature-insensitive fat vector. A vector in a complex domain represents a given voxel's magnetization from an acquired, complex MR image. In this method, a circle was fit to a time series of vectors acquired from a heated region during a heating experiment. The circle center served as the fat vector, which was then subtracted from the acquired vectors, leaving only the temperature-sensitive vectors for thermal mapping. This work was verified with the gel phantoms of 10%, 15%, and 20% fat content and the ex vivo phantom of porcine abdomen tissue during water-bath heating. It was also tested with an ex vivo porcine tissue during focused ultrasound (FUS) heating.

RESULTS

A good agreement was found between the temperature measurements obtained from the proposed method and the optical fiber temperature probe in the verification experiments. In the gel phantoms, the linear regression provided a slope of 0.992 and an R² of 0.994. The Bland-Altman analysis gave a bias of 0.49°C and a 95% confidence interval of ±1.60°C. In the ex vivo tissue, the results of the linear regression and Bland-Altman methods provided a slope of 0.979, an intercept of 0.353, an R² of 0.947, and a 95% confidence interval of ±3.26°C with a bias of -0.14°C. In FUS tests, a temperature discrepancy of up to 28% was observed between the proposed and conventional PRF methods in ex vivo tissues containing fat.

CONCLUSIONS

The proposed PRF-based method can improve the accuracy of the temperature measurements in tissues with fat, such as breast, abdomen, prostate, and bone marrow.

Foundations of Magnetic Resonance-Guided Focused Ultrasonography

The ability of ultrasonography to safely penetrate deeply into the brain has made it an attractive technology for neurological applications for almost 1 century. Having recognized that converging ultrasound waves could deliver high levels of energy to a target and spare the overlying and surrounding brain, early applications used craniotomies to allow transducers to contact the brain or dural surface. The development of transducer arrays that could permit the transit of sufficient numbers of ultrasound waves to deliver high energies to a target, even with the loss of energy from the skull, has now resulted in clinical systems that can permit noninvasive focused ultrasound procedures that leave the skull intact. Another major milestone in the field was the marriage of focused ultrasonography with magnetic resonance thermometry. This provides real-time feedback regarding the level and location of brain tissue heating, allowing for precise elevation of temperatures within a desired target to lead to focal therapeutic lesions. The major clinical use of this technology, at present, has been limited to treatment of refractory essential tremor and parkinsonian tremor, although the first study of this approach had targeted sensory thalamus for refractory pain, and new targets and disease indications are under study. Finally, focused ultrasonography can also be used at a lower frequency and energy level when combined with intravenous microbubbles to create cavitations, which will open the blood-brain barrier rather than ablate tissue. In the present review, we have discussed the historical and scientific foundations and current clinical applications of magnetic resonance-guided focused ultrasonography and the genesis and background that led to the use of this technique for focal blood-brain barrier disruption.

Investigation of Artifacts and Optimization in Proton Resonance Frequency Thermometry Towards Heating Risk Monitoring of Implantable Medical Devices in Magnetic Resonance Imaging

OBJECTIVE

Artifacts limit the application of proton resonance frequency (PRF) thermometry for on-site, individualized heating evaluations of implantable medical devices such as deep brain stimulation (DBS) for use in magnetic resonance imaging (MRI). Its properties are unclear and the research on how to choose an unaffected measurement region is insufficient.

METHODS

The properties of PRF signals around the metallic DBS electrode were investigated through simulations and phantom experiments considering electromagnetic interferences from material susceptibility and the radio frequency (RF) interactions. A threshold method on phase difference Δϕ was used to define a measurement area to estimate heating at the electrode surface. Its performance was compared to that of the Bayesian magnitude method and probe measurements.

RESULTS

The B₀ magnetic field inhomogeneity due to the electrode susceptibility was the main influencing factor on PRF compared to the RF artifact. Δϕ around the electrode followed normal distribution but was distorted. Underestimation occurred at places with high temperature rises. The noise was increased and could be well estimated from magnitude images using a modified NEMA method. The Δϕ-threshold method based on this knowledge outperformed the Bayesian magnitude method by more than 42% in estimation error of the electrode heating.

CONCLUSION

The findings favor the use of PRF with the proposed approach as a reliable method for electrode heating estimation.

SIGNIFICANCE

This study clarified the influence of device artifacts and could improve the performance of PRF thermometry for individualized heating assessments of patients with implants under MRI.

Salvage interstitial laser thermal therapy under MRI guidance (MRgFLA) for high-intensity focal ultrasound (HIFU) recurrences: feasibility study

While focal therapy (FT) is increasingly endorsed for treating localized prostate cancer in the appropriately selected patient, management of recurrences following FT is not well-established in the literature. This case series describes three patients who received high-intensity focal ultrasound (HIFU) for primary treatment followed by focal laser interstitial thermal therapy (FLTT) for salvage therapy treated in the context of an ongoing clinical trial. Evaluation of these reported patients demonstrates that FLTT is feasible in the salvage setting with promising short-term oncologic outcomes and with the potential to preserve functional outcomes. Repeat focal therapy for previous failures is feasible however, it requires sophisticated imaging modalities for the accurate identification of recurrence and treatment of the tumor.

Highly sensitive T1-T2dual-mode MRI probe based on ultra-small gadolinium oxide-decorated iron oxide nanocrystals

Single-mode magnetic resonance imaging (MRI) contrast agents (CAs) in clinical settings are easily disturbed by calcification, bleeding, and adipose signals, which result in inaccurate diagnoses. In this study, we developed a highly efficient T₁-T₂dual-mode MRI CA using an ultra-small gadolinium oxide-decorated magnetic iron oxide nanocrystal (GMIO). The gadolinium element could effectively alter the magnetic properties of the GMIO from soft-ferromagnetism to superparamagnetism. In addition, when the Gd/Fe ratio was 15 % (designated as GMIO-2), the GMIO-2 possessed the best superparamagnetism and highest magnetism. Subsequently, T₁and T₂values of GMIO-2 were measured through a series of turbo spin-echo images and then multi-spin echo (MSE) sequence, respectively. Based on this, T₁and T₂relaxivities of GMIO-2 were calculated and were the highest (r₁: 1.306 m M^-1s^-1and r₂: 234.5 m M^-1s^-1) when compared to other groups. The cytotoxicity of GMIO-2 was negligible under a wide range of dosages, thus exhibiting excellent cell biocompatibility. Moreover, GMIO-2 could quickly diffuse into cells, leading to its effective accumulation. The systemic delivery of GMIO-2 resulted in an excellent T₁-T₂dual-mode MRI contrast effect in kidneys, which is expected to improve the diagnosis of kidney lesions. Therefore, this work provides a promising candidate for the development of a T₁-T₂dual-mode MRI CA.

Magnetic resonance shear wave elastography using transient acoustic radiation force excitations and sinusoidal displacement encoding

A magnetic resonance (MR) shear wave elastography technique that uses transient acoustic radiation force impulses from a focused ultrasound (FUS) transducer and a sinusoidal-shaped MR displacement encoding strategy is presented. Using this encoding strategy, an analytic expression for calculating the shear wave speed in a heterogeneous medium was derived. Green's function-based simulations were used to evaluate the feasibility of calculating shear wave speed maps using the analytic expression. Accuracy of simulation technique was confirmed experimentally in a homogeneous gelatin phantom. The elastography measurement was compared to harmonic MR elastography in a homogeneous phantom experiment and the measured shear wave speed values differed by less than 14%. This new transient elastography approach was able to map the position and shape of inclusions sized from 8.5 to 14 mm in an inclusion phantom experiment. These preliminary results demonstrate the feasibility of using a straightforward analytic expression to generate shear wave speed maps from MR images where sinusoidal-shaped motion encoding gradients are used to encode the displacement-time history of a transiently propagating wave-packet. This new measurement technique may be particularly well suited for performing elastography before, during, and after MR-guided FUS therapies since the same device used for therapy is also used as an excitation source for elastography.

Techniques for Temperature Monitoring of Myocardial Tissue Undergoing Radiofrequency Ablation Treatments: An Overview

Cardiac radiofrequency ablation (RFA) has received substantial attention for the treatment of multiple arrhythmias. In this scenario, there is an ever-growing demand for monitoring the temperature trend inside the tissue as it may allow an accurate control of the treatment effects, with a consequent improvement of the clinical outcomes. There are many methods for monitoring temperature in tissues undergoing RFA, which can be divided into invasive and non-invasive. This paper aims to provide an overview of the currently available techniques for temperature detection in this clinical scenario. Firstly, we describe the heat generation during RFA, then we report the principle of work of the most popular thermometric techniques and their features. Finally, we introduce their main applications in the field of cardiac RFA to explore the applicability in clinical settings of each method.

MRI-guided Focused Ultrasound Ablation for Localized Intermediate-Risk Prostate Cancer: Early Results of a Phase II Trial

Background To reduce adverse effects of whole-gland therapy, participants with localized clinically significant prostate cancer can undergo MRI-guided focal therapy. Purpose To explore safety and early oncologic and functional outcomes of targeted focal high-intensity focused ultrasound performed under MRI-guided focused ultrasound for intermediate-risk clinically significant prostate cancer. Materials and Methods In this prospective phase II trial, between February 2016 and July 2019, men with unifocal clinically significant prostate cancer visible at MRI were treated with transrectal MRI-guided focused ultrasound. The primary end point was the 5-month biopsy (last recorded in December 2019) with continuation to the 24-month follow-up projected to December 2021. Real-time ablation monitoring was performed with MR thermography. Nonperfused volume was measured at treatment completion. Periprocedural complications were recorded. Follow-up included International Prostate Symptom Score (IPSS) and International Index of Erectile Function-15 (IIEF-15) score at 6 weeks and 5 months, and multiparametric MRI and targeted biopsy of the treated area at 5 months. The generalized estimating equation model was used for statistical analysis, and the Holm method was used to adjust P value. Results Treatment was successfully completed in all 44 men, 36 with grade group (GG) 2 and eight with GG 3 disease (median age, 67 years; interquartile range [IQR], 62-70 years). No major treatment-related adverse events occurred. Forty-one of 44 participants (93%; 95% CI: 82, 98) were free of clinically significant prostate cancer (≥6 mm GG 1 disease or any volume ≥GG 2 disease) at the treatment site at 5-month biopsy (median, seven cores). Median IIEF-15 and IPSS scores were similar at baseline and at 5 months (IIEF-15 score at baseline, 61 [IQR, 34-67] and at 5 months, 53 [IQR, 24-65.5], P = .18; IPSS score at baseline, 3.5 [IQR, 1.8-7] and at 5 months, 6 [IQR, 2-7.3], P = .43). Larger ablations (≥15 cm³) compared with smaller ones were associated with a decline in IIEF-15 scores at 6 weeks (adjusted P < .01) and at 5 months (adjusted P = .07). Conclusion Targeted focal therapy of intermediate-risk prostate cancer performed with MRI-guided focused ultrasound ablation was safe and had encouraging early oncologic and functional outcomes. © RSNA, 2021 Online supplemental material is available for this article See also the editorial by Tempany-Afdhal in this issue.

Clinical Performance and Future Potential of Magnetic Resonance Thermometry in Hyperthermia

Simple Summary

Hyperthermia is a treatment for cancer patients, which consists of heating the body to 43 °C. The temperature during treatment is usually measured by placing temperature probes intraluminal or invasively. The only clinically used option to measure temperature distributions non-invasively and in 3D is by MR thermometry (MRT). However, in order to be able to replace conventional temperature probes, MRT needs to become more reliable. In this review paper, we propose standardized performance thresholds for MRT, based on our experience of treating nearly 4000 patients. We then review the literature to assess to what extent these requirements are already being met in the clinic today and identify common problems. Lastly, using pre-clinical results in the literature, we assess where the biggest potential is to solve the problems identified. We hope that by standardizing MRT parameters as well as highlighting current and promising developments, progress in the field will be accelerated.

Abstract

Hyperthermia treatments in the clinic rely on accurate temperature measurements to guide treatments and evaluate clinical outcome. Currently, magnetic resonance thermometry (MRT) is the only clinical option to non-invasively measure 3D temperature distributions. In this review, we evaluate the status quo and emerging approaches in this evolving technology for replacing conventional dosimetry based on intraluminal or invasively placed probes. First, we define standardized MRT performance thresholds, aiming at facilitating transparency in this field when comparing MR temperature mapping performance for the various scenarios that hyperthermia is currently applied in the clinic. This is based upon our clinical experience of treating nearly 4000 patients with superficial and deep hyperthermia. Second, we perform a systematic literature review, assessing MRT performance in (I) clinical and (II) pre-clinical papers. From (I) we identify the current clinical status of MRT, including the problems faced and from (II) we extract promising new techniques with the potential to accelerate progress. From (I) we found that the basic requirements for MRT during hyperthermia in the clinic are largely met for regions without motion, for example extremities. In more challenging regions (abdomen and thorax), progress has been stagnating after the clinical introduction of MRT-guided hyperthermia over 20 years ago. One clear difficulty for advancement is that performance is not or not uniformly reported, but also that studies often omit important details regarding their approach. Motion was found to be the common main issue hindering accurate MRT. Based on (II), we reported and highlighted promising developments to tackle the issues resulting from motion (directly or indirectly), including new developments as well as optimization of already existing strategies. Combined, these may have the potential to facilitate improvement in MRT in the form of more stable and reliable measurements via better stability and accuracy.

EXAFS investigations of temperature-dependent structure in cobalt-59 molecular NMR thermometers

Cobalt-59 nuclei are known for extremely thermally sensitive chemical shifts (δ), which in the long term could yield novel magnetic resonance thermometers for bioimaging applications. In this manuscript, we apply extended X-ray absorption fine structure (EXAFS) spectroscopy for the first time to probe the exact variations in physical structure that produce the exceptional thermal sensitivity of the 59Co NMR chemical shift. We apply this spectroscopic technique to five Co(iii) complexes: [Co(NH3)6]Cl3 (1), [Co(en)3]Cl3 (2) (en = ethylenediamine), [Co(tn)3]Cl3 (3) (tn = trimethylenediamine), [Co(tame)2]Cl3 (4) (tame = 1,1,1-tris(aminomethyl)ethane), and [Co(diNOsar)]Cl3 (5) (diNOsar = dinitrosarcophagine). The solution-phase EXAFS data reveal increasing Co-N bond distances for these aqueous complexes over a ∼50 °C temperature window, expanding by Δr(Co-N) = 0.0256(6) Å, 0.0020(5) Å, 0.0084(5) Å, 0.0006(5) Å, and 0.0075(6) Å for 1-5, respectively. Computational analyses of the structural changes reveal that increased connectivity between the donor atoms encourages complex structural variations. These results imply that rich temperature-dependent structural variations define 59Co NMR thermometry in macrocyclic complexes.

Proton Resonance Frequency Shift Thermometry: A Review of Modern Clinical Practices

Magnetic resonance imaging (MRI) has become a popular modality in guiding minimally invasive thermal therapies, due to its advanced, nonionizing, imaging capabilities and its ability to record changes in temperature. A variety of MR thermometry techniques have been developed over the years, and proton resonance frequency (PRF) shift thermometry is the current clinical gold standard to treat a variety of cancers. It is used extensively to guide hyperthermic thermal ablation techniques such as high-intensity focused ultrasound (HIFU) and laser-induced thermal therapy (LITT). Essential attributes of PRF shift thermometry include excellent linearity with temperature, good sensitivity, and independence from tissue type. This noninvasive temperature mapping method gives accurate quantitative measures of the temperature evolution inside biological tissues. In this review, the current status and new developments in the fields of MR-guided HIFU and LITT are presented with an emphasis on breast, prostate, bone, uterine, and brain treatments. LEVEL OF EVIDENCE: 5 TECHNICAL EFFICACY STAGE: 3.

Fiber Bragg Grating Sensors for Performance Evaluation of Fast Magnetic Resonance Thermometry on Synthetic Phantom

The increasing recognition of minimally invasive thermal treatment of tumors motivate the development of accurate thermometry approaches for guaranteeing the therapeutic efficacy and safety. Magnetic Resonance Thermometry Imaging (MRTI) is nowadays considered the gold-standard in thermometry for tumor thermal therapy, and assessment of its performances is required for clinical applications. This study evaluates the accuracy of fast MRTI on a synthetic phantom, using dense ultra-short Fiber Bragg Grating (FBG) array, as a reference. Fast MRTI is achieved with a multi-slice gradient-echo echo-planar imaging (GRE-EPI) sequence, allowing monitoring the temperature increase induced with a 980 nm laser source. The temperature distributions measured with 1 mm-spatial resolution with both FBGs and MRTI were compared. The root mean squared error (RMSE) value obtained by comparing temperature profiles showed a maximum error of 1.2 °C. The Bland-Altman analysis revealed a mean of difference of 0.1 °C and limits of agreement 1.5/−1.3 °C. FBG sensors allowed to extensively assess the performances of the GRE-EPI sequence, in addition to the information on the MRTI precision estimated by considering the signal-to-noise ratio of the images (0.4 °C). Overall, the results obtained for the GRE-EPI fully satisfy the accuracy (~2 °C) required for proper temperature monitoring during thermal therapies.

Development and characterization of a tissue mimicking psyllium husk gelatin phantom for ultrasound and magnetic resonance imaging

Purpose: To develop and characterize a tissue-mimicking phantom that enables the direct comparison of magnetic resonance (MR) and ultrasound (US) imaging techniques useful for monitoring high-intensity focused ultrasound (HIFU) treatments. With no additions, gelatin phantoms produce little if any scattering required for US imaging. This study characterizes the MR and US image characteristics as a function of psyllium husk concentration, which was added to increase US scattering.Methods: Gelatin phantoms were constructed with varying concentrations of psyllium husk. The effects of psyllium husk concentration on US B-mode and MR imaging were evaluated at nine different concentrations. T1, T2, and T2* MR maps were acquired. Acoustic properties (attenuation and speed of sound) were measured at frequencies of 0.6, 1.0, 1.8, and 3.0 MHz using a through-transmission technique. Phantom elastic properties were evaluated for both time and temperature dependence.Results: Ultrasound image echogenicity increased with increasing psyllium husk concentration while quality of gradient-recalled echo MR images decreased with increasing concentration. For all phantoms, the measured speed of sound ranged between 1567-1569 m/s and the attenuation ranged between 0.42-0.44 dB/(cm·MHz). Measured T1 ranged from 974-1051 ms. The T2 and T2* values ranged from 97-108 ms and 48-88 ms, respectively, with both showing a decreasing trend with increased psyllium husk concentration. Phantom stiffness, measured using US shear-wave speed measurements, increased with age and decreased with increasing temperature.Conclusions: The presented dual-use tissue-mimicking phantom is easy to manufacture and can be used to compare and evaluate US-guided and MR-guided HIFU imaging protocols.

Contactless Thermometry by MRI and MRS: Advanced Methods for Thermotherapy and Biomaterials

Control of temperature variation is of primordial importance in particular areas of biomedicine. In this context, medical treatments such as hyperthermia and cryotherapy, and also the development and use of hydrogel-based biomaterials, are of particular concern. To enable accurate temperature measurement without perturbing or even destroying the biological tissue or material to be monitored, contactless thermometry methods are preferred. Among these, the most suitable are based on magnetic resonance imaging and spectroscopy (MRI, MRS). Here, we address the latest developments in this field as well as their current and anticipated practical applications. We highlight recent progress aimed at rendering MR thermometry faster and more reproducible, versatile, and sophisticated and provide our perspective on how these new techniques broaden the range of applications in medical treatments and biomaterial development by enabling insight into finer details of thermal behavior. Thus, these methods facilitate optimization of clinical and industrial heating and cooling protocols.

Systematic review of pre-clinical and clinical devices for magnetic resonance-guided radiofrequency hyperthermia

Clinical trials have demonstrated the therapeutic benefits of adding radiofrequency (RF) hyperthermia (HT) as an adjuvant to radio- and chemotherapy. However, maximum utilization of these benefits is hampered by the current inability to maintain the temperature within the desired range. RF HT treatment quality is usually monitored by invasive temperature sensors, which provide limited data sampling and are prone to infection risks. Magnetic resonance (MR) temperature imaging has been developed to overcome these hurdles by allowing noninvasive 3D temperature monitoring in the target and normal tissues. To exploit this feature, several approaches for inserting the RF heating devices into the MR scanner have been proposed over the years. In this review, we summarize the status quo in MR-guided RF HT devices and analyze trends in these hybrid hardware configurations. In addition, we discuss the various approaches, extract best practices and identify gaps regarding the experimental validation procedures for MR - RF HT, aimed at converging to a common standard in this process.

Phylogenic Determinants of Cardiovascular Frailty, Focus on Hemodynamics and Arterial Smooth Muscle Cells

The evolution of the circulatory system from invertebrates to mammals has involved the passage from an open system to a closed in-parallel system via a closed in-series system, accompanying the increasing complexity and efficiency of life’s biological functions. The archaic heart enables pulsatile motion waves of hemolymph in invertebrates, and the in-series circulation in fish occurs with only an endothelium, whereas mural smooth muscle cells appear later. The present review focuses on evolution of the circulatory system. In particular, we address how and why this evolution took place from a closed, flowing, longitudinal conductance at low pressure to a flowing, highly pressurized and bifurcating arterial compartment. However, although arterial pressure was the latest acquired hemodynamic variable, the general teleonomy of the evolution of species is the differentiation of individual organ function, supported by specific fueling allowing and favoring partial metabolic autonomy. This was achieved via the establishment of an active contractile tone in resistance arteries, which permitted the regulation of blood supply to specific organ activities via its localized function-dependent inhibition (active vasodilation). The global resistance to viscous blood flow is the peripheral increase in frictional forces caused by the tonic change in arterial and arteriolar radius, which backscatter as systemic arterial blood pressure. Consequently, the arterial pressure gradient from circulating blood to the adventitial interstitium generates the unidirectional outward radial advective conductance of plasma solutes across the wall of conductance arteries. This hemodynamic evolution was accompanied by important changes in arterial wall structure, supported by smooth muscle cell functional plasticity, including contractility, matrix synthesis and proliferation, endocytosis and phagocytosis, etc. These adaptive phenotypic shifts are due to epigenetic regulation, mainly related to mechanotransduction. These paradigms actively participate in cardio-arterial pathologies such as atheroma, valve disease, heart failure, aneurysms, hypertension, and physiological aging.

RF heating measurement using MR thermometry and field monitoring: Methodological considerations and first in vivo results

PURPOSE

A MR thermometry (MRT) method with field monitoring is proposed to improve the measurement of small temperature variations induced in brain MRI exams.

METHODS

MR thermometry experiments were performed at 7 Tesla with concurrent field monitoring and RF heating. Images were reconstructed with nominal k-space trajectories and with first-order spherical harmonics correction. Experiments were performed in vitro with deliberate field disturbances and on an anesthetized macaque in 2 different specific absorption rate regimes, that is, at 50% and 100% of the maximal specific absorption rate level allowed in the International Electrotechnical Commission normal mode of operation. Repeatability was assessed by running a second separate session on the same animal.

RESULTS

Inclusion of magnetic field fluctuations in the reconstruction improved temperature measurement accuracy in vitro down to 0.02°C. Measurement precision in vivo was on the order of 0.15°C in areas little affected by motion. In the same region, temperature increase reached 0.5 to 0.8°C after 20 min of heating at 100% specific absorption rates and followed a rough factor of 2 with the 50% specific absorption rate scans. A horizontal temperature plateau, as predicted by Pennes bioheat model with thermal constants from the literature and constant blood temperature assumption, was not observed.

CONCLUSION

Inclusion of field fluctuations in image reconstruction was beneficial for the measurement of small temperature rises encountered in standard brain exams. More work is needed to correct for motion-induced field disturbances to extract reliable temperature maps.

Technical Note: Effect of transducer position and ground plane configuration on image quality in MR-guided focused ultrasound therapies

PURPOSE

To evaluate the effect of a focused ultrasound transducer position and ground plane configuration on magnetic resonance image quality.

METHODS

The effect of transducer position with respect to the MRI B0 field and the radiofrequency receive coils was evaluated in a breast-specific MRgFUS system with an integrated RF phased-array coil. Image signal-to-noise ratio was evaluated at different transducer locations. The effect of ultrasound transducer ground plane configuration was evaluated using a replica transducer with 12 ground plane configurations. All evaluations were performed at 3 Tesla.

RESULTS

Both transducer position and ground plane configuration were found to have a considerable effect on overall image SNR. A 67% increase in SNR was achieved by positioning the transducer face perpendicular to the B0 field. A 25% increase in SNR was achieved by segmenting the replica transducer ground plane from one continuous plane to nine individual segments.

CONCLUSIONS

Advances in focused ultrasound hardware allow for integrated radiofrequency MRI coils as well as adjustable transducer positioning. The placement of the ultrasound transducer with respect to both the magnetic field and RF coils can have a considerable effect on image SNR and the resulting MR images that are used for MR-guided focused ultrasound treatment planning, monitoring and assessment.

Imaging-based internal body temperature measurements: The journal Temperature toolbox

Noninvasive imaging methods of internal body temperature are in high demand in both clinical medicine and physiological research. Thermography and thermometry can be used to assess tissue temperature during thermal therapies: ablative and hyperthermia treatments to ensure adequate temperature rise in target tissues but also to avoid collateral damage by heating healthy tissues. In research use, measurement of internal body temperature enables us the production of thermal maps on muscles, internal organs, and other tissues of interest. The most used methods for noninvasive imaging of internal body temperature are based on different parameters acquired with magnetic resonance imaging, ultrasound, computed tomography, microwave radiometry, photoacoustic imaging, and near-infrared spectroscopy. In the current review, we examine the aforementioned imaging methods, their use in estimating internal body temperature in vivo with their advantages and disadvantages, and the physical phenomena the thermography or thermometry modalities are based on.

The Potential of Adjusting Water Bolus Liquid Properties for Economic and Precise MR Thermometry Guided Radiofrequency Hyperthermia

The potential of MR thermometry (MRT) fostered the development of MRI compatible radiofrequency (RF) hyperthermia devices. Such device integration creates major technological challenges and a crucial point for image quality is the water bolus (WB). The WB is located between the patient body and external sources to both couple electromagnetic energy and to cool the patient skin. However, the WB causes MRT errors and unnecessarily large field of view. In this work, we studied making the WB MRI transparent by an optimal concentration of compounds capable of modifying T2* relaxation without an impact on the efficiency of RF heating. Three different T2* reducing compounds were investigated, namely CuSO4, MnCl2, and Fe3O4. First, electromagnetic properties and T2* relaxation rates at 1.5 T were measured. Next, through multi-physics simulations, the predicted effect on the RF-power deposition pattern was evaluated and MRT precision was experimentally assessed. Our results identified 5 mM Fe3O4 solution as optimal since it does not alter the RF-power level needed and improved MRT precision from 0.39 °C to 0.09 °C. MnCl2 showed a similar MRT improvement, but caused unacceptable RF-power losses. We conclude that adding Fe3O4 has significant potential to improve RF hyperthermia treatment monitoring under MR guidance.

Recent technological advancements in radiofrequency- andmicrowave-mediated hyperthermia for enhancing drug delivery

Hyperthermia therapy is a potent enhancer of chemotherapy and radiotherapy. In particular, microwave (MW) and radiofrequency (RF) hyperthermia devices provide a variety of heating approaches that can treat most cancers regardless the size. This review introduces the physics of MW/RF hyperthermia, the current state-of-the-art systems for both localized and regional heating, and recent advancements in hyperthermia treatment guidance using real-time computational simulations and magnetic resonance thermometry. Clinical trials involving RF/MW hyperthermia as adjuvant for chemotherapy are also presented per anatomical site. These studies favor the use of adjuvant hyperthermia since it significantly improves curative and palliative clinical outcomes. The main challenge of hyperthermia is the distribution of state-of-the-art heating systems. Nevertheless, we anticipate that recent technology advances will expand the use of hyperthermia to chemotherapy centers for enhanced drug delivery. These new technologies hold great promise not only for (image-guided) perfusion modulation and sensitization for cytotoxic drugs, but also for local delivery of various compounds using thermosensitive liposomes.

T2 mapping as a predictor of nonperfused volume in MRgFUS treatment of desmoid tumors

Objective: The objective of this study was to develop an alternative method of non-contrast monitoring of tissue ablation during focused ultrasound treatment. Desmoid tumors are benign but locally aggressive soft tissue tumors that arise from fibroblast cells. Magnetic resonance-guided focused ultrasound (MRgFUS) has emerged as an alternative to conventional therapies, showing promising results in reduction of tumor volume without significant side effects. The gold-standard assessment of the reduction of viable tumor volume post-treatment is non-perfused volume (NPV) and evaluation of NPV is typically performed with post-treatment gadolinium enhanced MR imaging. However, as gadolinium cannot be repeatedly administered during treatments, there is a need for alternative non-contrast monitoring of the tissue to prevent over and under treatment. Methods: Double-echo and multi-echo images were acquired before, during and after the MRgFUS treatment. T2 maps were generated with an exponential fit and T2 maps were compared to post-treatment post-contrast images.Results: In all five MRgFUS treatment sessions, T2 mapping showed excellent qualitative agreement with the post-contrast NPV.Conclusions: T2 mapping may be used to visualize the extent of ablation with focused ultrasound and can be used as a predictor of NPV prior to the administration of contrast during the post-treatment assessment.

Multinuclear absolute magnetic resonance thermometry

Non-invasive measurement of absolute temperature is important for proper characterization of various pathologies and for evaluation of thermal dose during interventional procedures. The proton (hydrogen nucleus) magnetic resonance (MR) frequency shift method can be used to map relative temperature changes. However, spatiotemporal variations in the main magnetic field and the lack of local internal frequency reference challenge the determination of absolute temperature. Here, we introduce a multinuclear method for absolute MR thermometry, based on the fact that the hydrogen and sodium nuclei exhibit a unique and distinct characteristic frequency dependence with temperature and with electrolyte concentration. A one-to-one mapping between the precession frequency difference of the two nuclei and absolute temperature is demonstrated. Proof-of-concept experiments were conducted in aqueous solutions with different NaCl concentrations, in agarose gel samples, and in freshly excised ex vivo mouse tissues. One-dimensional chemical shift imaging experiments also demonstrated excellent agreement with infrared measurements.