The role of surfactants in dispersion of carbon nanotubes

An Electronic and Optically Controlled Bifunctional Transistor Based on a Bio-Nano Hybrid Complex

We report an electronically and optically controlled bioelectronic field-effect transistor (FET) based on the hybrid film of photoactive bacteriorhodopsin and electronically conducting single-walled carbon nanotubes (SWNTs). Two-dimensional (2D) crystals of bacteriorhodopsin form the photoactive center of the bio-nano complex, whereas one-dimensional (1D) pure SWNTs provide the required electronic support. The redshift in the Raman spectra indicates the electronic doping with an estimated charge density of 3 × 10⁶ cm^-2. The hybrid structure shows a conductivity of 19 μS/m and semiconducting characteristics due to preferential binding with selective diameters of semiconducting SWNTs. The bioelectronic transistor fabricated using direct laser lithography shows both optical and electronic gating with a significant on/off switch ratio of 8.5 and a photoconductivity of 13.15 μS/m. An n-type FET shows complementary p-type characteristics under light due to optically controlled, electronic doping by the "proton-pumping" bacteriorhodopsin. The fabricated bioelectronic transistor exhibits both electronically and optically well-controlled bifunctionality based on the functionalized hybrid electronic material.

Effect of carbon nanotube doping on the energy dissipation and rate dependent deformation behavior of polyurethane foams

An experimental investigation is performed to characterize the effect of carbon nanotubes on the average mechanical properties of polyurethane foams. Polyurethane foams are doped with as-grown and oxidized carbon nanotubes at varying carbon nanotube concentrations. It is observed that the inclusion of carbon nanotubes up to a threshold concentration decreases the density of freely expanding polyurethane foams. Uniaxial and cyclic compression testing of foam samples is carried out to study their energy dissipation and rate dependent deformation behavior. While energy dissipation is observed to be higher in neat polyurethane foams, carbon nanotube reinforced foams show better recovery when compressed beyond elastic limit due to their stiffer foam cell walls. It is shown that incorporation of oxidized carbon nanotubes should be preferred over as grown carbon nanotubes to improve flexural, thermal and acoustic response of polyurethane foams. Scanning electron microscopy analysis of compressed samples reveals that cell shearing; cell bending and fracture at nodes are the predominant mode of deformation in all foam samples.

Elucidation of Antimicrobial Activity of Non-Covalently Dispersed Carbon Nanotubes

Microorganisms have begun to develop resistance because of inappropriate and extensive use of antibiotics in the hospital setting. Therefore, it seems to be necessary to find a way to tackle these pathogens by developing new and effective antimicrobial agents. Carbon nanotubes (CNTs) have attracted growing attention because of their remarkable mechanical strength, electrical properties, and chemical and thermal stability for their potential applications in the field of biomedical as therapeutic and diagnostic nanotools. However, the impact of carbon nanotubes on microbial growth has not been fully investigated. The primary purpose of this research study is to investigate the antimicrobial activity of CNTs, particularly double-walled and multi-walled nanotubes on representative pathogenic strains such as Gram-positive bacteria Staphylococcus aureus, Gram-negative bacteria Pseudomonas aeruginosa, Klebsiella pneumoniae, and fungal strain Candida albicans. The dispersion ability of CNT types (double-walled and multi-walled) treated with a surfactant such as sodium dodecyl-benzenesulfonate (SDBS) and their impact on the microbial growth inhibition were also examined. A stock concentration 0.2 mg/mL of both double-walled and multi-walled CNTs was prepared homogenized by dispersing in surfactant solution by using probe sonication. UV-vis absorbance, Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM) were used for the characterization of CNTs dispersed in the surfactant solution to study the interaction between molecules of surfactant and CNTs. Later, scanning electron microscopy (SEM) was used to investigate how CNTs interact with the microbial cells. The antimicrobial activity was determined by analyzing optical density growth curves and viable cell count. This study revealed that microbial growth inhibited by non-covalently dispersed CNTs was both depend on the concentration and treatment time. In conclusion, the binding of surfactant molecules to the surface of CNTs increases its ability to disperse in aqueous solution. Non-covalent method of CNTs dispersion preserved their structure and increased microbial growth inhibition as a result. Multi-walled CNTs exhibited higher antimicrobial activity compared to double-walled CNTs against selected pathogens.

Improving Dispersion of Recycled Discontinuous Carbon Fibres to Increase Fibre Throughput in the HiPerDiF Process

In order to increase the material throughput of aligned discontinuous fibre composites using technologies such as HiPerDiF, stability of the carbon fibres in an aqueous solution needs to be achieved. Subsequently, a range of surfactants, typically employed to disperse carbon-based materials, have been assessed to determine the most appropriate for use in this regard. The optimum stability of the discontinuous fibres was observed when using the anionic surfactant, sodium dodecylbenzene sulphonate, which was superior to a range of other non-ionic and anionic surfactants, and single-fibre fragmentation demonstrated that the employment of sodium dodecylbenzene sulphonate did not affect the interfacial adhesion between fibres. Rheometry was used to complement the study, to understand the potential mechanisms of the improved stability of discontinuous fibres in aqueous suspension, and it led to the understanding that the increased viscosity was a significant factor. For the shear rates employed, fibre deformation was neither expected nor observed.

Mineral Scale Prevention on Electrically Conducting Membrane Distillation Membranes Using Induced Electrophoretic Mixing

The growth of mineral crystals on surfaces is a challenge across multiple industrial processes. Membrane-based desalination processes, in particular, are plagued by crystal growth (known as scaling), which restricts the flow of water through the membrane, can cause membrane wetting in membrane distillation, and can lead to the physical destruction of the membrane material. Scaling occurs when supersaturated conditions develop along the membrane surface due to the passage of water through the membrane, a process known as concentration polarization. To reduce scaling, concentration polarization is minimized by encouraging turbulent conditions and by reducing the amount of water recovered from the saline feed. In addition, antiscaling chemicals can be used to reduce the availability of cations. Here, we report on an energy-efficient electrophoretic mixing method capable of nearly eliminating CaSO₄ and silicate scaling on electrically conducting membrane distillation (ECMD) membranes. The ECMD membrane material is composed of a percolating layer of carbon nanotubes deposited on porous polypropylene support and cross-linked by poly(vinyl alcohol). The application of low alternating potentials (2 V_pp,1Hz) had a dramatic impact on scale formation, with the impact highly dependent on the frequency of the applied signal, and in the case of silicate, on the pH of the solution.

The mechanism for adsorption of Cr(VI) ions by PE microplastics in ternary system of natural water environment

More attention was paid to the attachment between microplastics and environmental pollutants. The adsorption performance of Polyethylene (PE) beads (a typical type of microplastics) and Cr(VI) ions with the existence of sodium dodecyl benzene sulfonate (SDBS) was investigated in this paper. The adsorption experiments of Cr(VI) ions by PE microplastics were conducted at different conditions, i.e. PE doses, pH and SDBS concentrations, respectively. The adsorption capability of Cr(VI) ions was increased from 0.39 to 1.36 mg⋅g^-1 when the dosage of PE microplastics was increased from 2 to 14 g ⋅L^-1 at pH of 5 with addition of SDBS, compared with increasing adsorption capability from 0.03 to 0.32 mg⋅g^-1 without addition of SDBS. The pH would influence the adsorption capability with and without the addition of SDBS. When the pH was less than 6, the adsorption capability of Cr(VI) would be promoted by the addition of SDBS; however, there was a contrast tendency when the pH was more than 6, which was attributed to that SDBS would compete with CrO₄^2- for occupying the adsorption sites of PE microplastic. The SDBS concentration would affect the adsorption performance of Cr(VI) ions onto PE microplastics. The peak of the adsorption capacity was at SDBS concentration between 1 and 1.5 mM. This research would provide a basis for investigating the influence of SDBS on adsorption performance of heavy metal by PE microplastics to simulate the surface attachment model of those three kinds of pollutants.

Carbon Nanotubes in Biomedicine

Nowadays, biomaterials have become a crucial element in numerous biomedical, preclinical, and clinical applications. The use of nanoparticles entails a great potential in these fields mainly because of the high ratio of surface atoms that modify the physicochemical properties and increases the chemical reactivity. Among them, carbon nanotubes (CNTs) have emerged as a powerful tool to improve biomedical approaches in the management of numerous diseases. CNTs have an excellent ability to penetrate cell membranes, and the sp² hybridization of all carbons enables their functionalization with almost every biomolecule or compound, allowing them to target cells and deliver drugs under the appropriate environmental stimuli. Besides, in the new promising field of artificial biomaterial generation, nanotubes are studied as the load in nanocomposite materials, improving their mechanical and electrical properties, or even for direct use as scaffolds in body tissue manufacturing. Nevertheless, despite their beneficial contributions, some major concerns need to be solved to boost the clinical development of CNTs, including poor solubility in water, low biodegradability and dispersivity, and toxicity problems associated with CNTs' interaction with biomolecules in tissues and organs, including the possible effects in the proteome and genome. This review performs a wide literature analysis to present the main and latest advances in the optimal design and characterization of carbon nanotubes with biomedical applications, and their capacities in different areas of preclinical research.

Recent advances in solid-contact ion-selective electrodes: functional materials, transduction mechanisms, and development trends

This article presents a comprehensive overview of recent progress in the design and applications of solid-contact ion-selective electrodes (SC-ISEs).

Peroxide Electrochemical Sensor and Biosensor Based on Nanocomposite of TiO2 Nanoparticle/Multi-Walled Carbon Nanotube Modified Glassy Carbon Electrode

A hydrogen peroxide (H₂O₂) sensor and biosensor based on modified multi-walled carbon nanotubes (CNTs) with titanium dioxide (TiO₂) nanostructures was designed and evaluated. The construction of the sensor was performed using a glassy carbon (GC) modified electrode with a TiO₂–CNT film and Prussian blue (PB) as an electrocalatyzer. The same sensor was also employed as the basis for H₂O₂ biosensor construction through further modification with horseradish peroxidase (HRP) immobilized at the TiO₂–fCNT film. Functionalized CNTs (fCNTs) and modified TiO₂–fCNTs were characterized by Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), and X-Ray DifFraction (XRD), confirming the presence of anatase over the fCNTs. Depending on the surface charge, a solvent which optimizes the CNT dispersion was selected: dimethyl formamide (DMF) for fCNTs and sodium dodecylsulfate (SDS) for TiO₂–fCNTs. Calculated values for the electron transfer rate constant (ks) were 0.027 s⁻¹ at the PB–fCNT/GC modified electrode and 4.7 × 10⁻⁴ s⁻¹ at the PB–TiO₂/fCNT/GC electrode, suggesting that, at the PB–TiO₂/fCNT/GC modified electrode, the electronic transfer was improved. According to these results, the PB–fCNT/GC electrode exhibited better Detection Limit (LD) and Quantification Limit (LQ) than the PB–TiO₂/fCNT/GC electrode for H₂O₂. However, the PB film was very unstable at the potentials used. Therefore, the PB–TiO₂/fCNT/GC modified electrode was considered the best for H₂O₂ detection in terms of operability. Cyclic Voltammetry (CV) behaviors of the HRP–TiO₂/fCNT/GC modified electrodes before and after the chronoamperometric test for H₂O₂, suggest the high stability of the enzymatic electrode. In comparison with other HRP/fCNT-based electrochemical biosensors previously described in the literature, the HRP–fCNTs/GC modified electrode did not show an electroanalytical response toward H₂O₂.

Titanate Nanotubes Engineered with Gold Nanoparticles and Docetaxel to Enhance Radiotherapy on Xenografted Prostate Tumors

Nanohybrids based on titanate nanotubes (TiONts) were developed to fight prostate cancer by intratumoral (IT) injection, and particular attention was paid to their step-by-step synthesis. TiONts were synthesized by a hydrothermal process. To develop the custom-engineered nanohybrids, the surface of TiONts was coated beforehand with a siloxane (APTES), and coupled with both dithiolated diethylenetriaminepentaacetic acid-modified gold nanoparticles (Au@DTDTPA NPs) and a heterobifunctional polymer (PEG₃₀₀₀) to significantly improve suspension stability and biocompatibility of TiONts for targeted biomedical applications. The pre-functionalized surface of this scaffold had reactive sites to graft therapeutic agents, such as docetaxel (DTX). This novel combination, aimed at retaining the AuNPs inside the tumor via TiONts, was able to enhance the radiation effect. Nanohybrids have been extensively characterized and were detectable by SPECT/CT imaging through grafted Au@DTDTPA NPs, radiolabeled with ¹¹¹In. In vitro results showed that TiONts-AuNPs-PEG₃₀₀₀-DTX had a substantial cytotoxic activity on human PC-3 prostate adenocarcinoma cells, unlike initial nanohybrids without DTX (Au@DTDTPA NPs and TiONts-AuNPs-PEG₃₀₀₀). Biodistribution studies demonstrated that these novel nanocarriers, consisting of AuNP- and DTX-grafted TiONts, were retained within the tumor for at least 20 days on mice PC-3 xenografted tumors after IT injection, delaying tumor growth upon irradiation.

Printing of wirelessly rechargeable solid-state supercapacitors for soft, smart contact lenses with continuous operations

Recent advances in smart contact lenses are essential to the realization of medical applications and vision imaging for augmented reality through wireless communication systems. However, previous research on smart contact lenses has been driven by a wired system or wireless power transfer with temporal and spatial restrictions, which can limit their continuous use and require energy storage devices. Also, the rigidity, heat, and large sizes of conventional batteries are not suitable for the soft, smart contact lens. Here, we describe a human pilot trial of a soft, smart contact lens with a wirelessly rechargeable, solid-state supercapacitor for continuous operation. After printing the supercapacitor, all device components (antenna, rectifier, and light-emitting diode) are fully integrated with stretchable structures for this soft lens without obstructing vision. The good reliability against thermal and electromagnetic radiations and the results of the in vivo tests provide the substantial promise of future smart contact lenses.

Hybrids of CO2-Responsive Water-Redispersible Single-Walled Carbon Nanotubes by a Surfactant Based on Natural Rosin

A kind of polymerizable dispersant based on natural rosin was used to disperse single-walled carbon nanotubes (SWNTs) in aqueous solution followed by in situ free-radical polymerization to achieve a controllable SWNTs dispersion, that not only can be controlled by CO₂/N₂, but can also be recycled and redispersed in CO₂-saturated water after drying without sonication.

Denatured lysozyme-coated carbon nanotubes: a versatile biohybrid material

Carbon nanotubes (CNTs) are among the most versatile nanomaterials, but their exploitation is hindered by limited dispersibility, especially in aqueous solvents. Here, we show that AP-LYS, a highly cationic soluble derivative of denatured hen egg lysozyme, is a very effective tool for the unbundling and solubilisation of CNTs. AP-LYS proved to mediate the complete and stable dispersion of CNTs at protein: CNT ratios ≥1: 3 (w:w) in very mild conditions (10–20 minutes sonication in ammonium acetate buffer, pH 5.0). Electrophoretic mobility and ζ-potential measurements confirmed that dispersed CNTs were coated by the protein, whereas molecular docking was used to study the interactions between AP-LYS and CNTs. AP-LYS-coated CNTs proved to be a very effective microbial cell-flocculating agent with an efficiency similar to that of chitosan, one of the best available flocculating agents, thus suggesting that this hybrid could find industrial applications in the treatment of wastewaters contaminated by microbial cells, or to remove microbial cells after fermentation processes. Moreover, we exploited the low stability of AP-LYS-coated CNT dispersions in eukaryotic cell culture media to prepare scaffolds with an extracellular matrix-like rough surface for the cultivation of eukaryotic cells.

Design of a pH-Responsive Conductive Nanocomposite Based on MWCNTs Stabilized in Water by Amphiphilic Block Copolymers

Homogeneous water dispersions of multi-walled carbon nanotubes (MWCNTs) were prepared by ultrasonication in the presence of an amphiphilic polystyrene-block-poly(acrylic acid) (PS-b-PAA) copolymer. The ability of PS-b-PAA to disperse and stabilize MWCTNs was investigated by UV-vis, SEM and zeta potential. The results show that the addition of a styrene block to PAA enhances the dispersion efficiency of the graphitic filler compared to pure PAA, possibly due to the nanotube affinity with the polystyrene moiety. Notably, the dispersions show an evident pH-responsive behavior, being MWCNTs reaggregation promoted in basic environment. It is worth noting that the responsive character is maintained in solid composites obtained by drop casting, thus indicating potential applications in sensing.

Electrochemical exfoliation of graphite in nanofibrillated kenaf cellulose (NFC)/surfactant mixture for the development of conductive paper

The effect of incorporating common dodecyl anionic and cationic surfactants such as dodecyltrimethylammonium bromide (DTAB), dodecylethyldimethylammonium bromide (DDAB), and sodium dodecylsulfate (SDS) in nanocomposites of reduced graphene oxide and nanocellulose are described. The stabilization and electrical properties of the nanocomoposites of reduced graphene oxide (RGO) and nanofibrillated kenaf cellulose (NFC) were characterized using four-point probe electrical conductivity measurements. Raman spectroscopy, field emission scanning electron microscopy, and high-resolution transmission electron microscopy were used to investigate dispersion morphology and the quality of RGO inside the NFC matrices. Small-angle neutron scattering (SANS) was used to study the aggregation behavior of the aqueous surfactant systems and RGO dispersions. The cationic surfactant DTAB proved to be the best choice for stabilization of RGO in NFC, giving enhanced electrical conductivity five orders of magnitude higher than the neat NFC. The results highlight the effects of hydrophilic surfactant moieties on the structure, stability and properties of RGO/NFC composites.

Potential-Driven Electron Transfer Lowers the Dissociation Energy of the C-F Bond and Facilitates Reductive Defluorination of Perfluorooctane Sulfonate (PFOS)

The widespread environmental occurrence of per- and polyfluoroalkyl substances (PFAS) has attracted significant regulatory, research, and media attention because of their toxicity, recalcitrance, and ability to bioaccumulate. Perfluorooctane sulfonate (PFOS) is a particularly troublesome member of the PFAS family due to its immunity to biological remediation and radical-based oxidation. In the present study, we present a heterogeneous reductive degradation process that couples direct electron transfer (ET) from surface-modified carbon nanotube electrodes (under low potential conditions) to sorbed PFOS molecules using UV-generated hydrated electrons without any further chemical addition. We demonstrate that the ET process dramatically increases the PFOS defluorination rate while yielding shorter chain (C₃-C₇) perfluorinated acids and present both experimental and ab initio evidence of the synergistic relationship between electron addition to sorbed molecules and their ability to react with reductive hydrated electrons. Because of the low energy consumption associated with the ET process, the use of standard medium-pressure UV lamps and no further chemical addition, this reductive degradation process is a promising method for the destruction of persistent organic pollutants, including PFAS and other recalcitrant halogenated organic compounds.

Properties of Cracking Patterns of Multi-Walled Carbon Nanotube-Reinforced Cement Matrix

The research presented in this paper presents a quantitative analysis of cracking patterns on the surface of cement paste, which has been modified by the addition of the multi-wall carbon nanotubes (MWCNTs). The cracking patterns analyzed were created as a result of increased temperature load. MWCNTs were used as an aqueous dispersion in the presence of a surfactant, sodium dodecyl sulfate (SDS). Four series of the cement paste were tested, and the samples differed in the water/cement (w/c) ratio, cement class, and the presence of MWCNTs. Image analysis tools were used to quantify the cracking patterns and it was proposed to measure parameters, such as the average cluster area, average cluster perimeter, average crack width, and crack density. In order to facilitate the image analysis process, the sample surface was subjected to preparation and using statistical analysis tools it was assessed whether the method of surface preparation affects the way the sample is cracked. The paper also presents the analysis of the relationships that occur between parameters describing the cracking patterns, and also with the physico-mechanical properties of the cement pastes. It was attempted to explain the dependencies using elements of fractal theory and the theory of dispersion systems.

The missing link between carbon nanotubes, dissolved organic matter and organic pollutants

Ternary interactions between carbon nanotubes (CNTs), dissolved organic matter (DOM) and small organic molecules (namely low molecular mass organic pollutants) are of great importance since they can affect the reactivity and fate of all involved compartments in the environment. This review thoroughly assesses existing knowledge on the adsorption of DOM and small organic molecules by CNTs, while giving special attention to (i) the complex nature of DOM, (ii) the ternary rather than binary interactions between CNTs, DOM and the small organic molecules and (iii) the DOM-organic molecule interactions. We discuss in detail the main factors influencing DOM adsorption by CNTs and attempt to differentiate between the role of DOM composition and conformation. We then outline how the presence of DOM influences the adsorption of small organic molecules by CNTs, considering the introduction stage of DOM and the impact of the organic molecule's properties. DOM adsorption by CNTs is highly dependent on its composition and is governed by the size, hydrophobicity and aromaticity of DOM. DOM adsorption was found to alter the assembly of the CNTs, resulting in changes in the distribution of adsorption sites. Small organic molecules may adsorb to residual surface area on the CNTs, to DOM-coating the CNTs or remain in solution, possibly complexed with DOM. This results in their suppressed or enhanced adsorption in comparison to DOM-free media. The physicochemical properties of the organic molecules (hydrophobicity, size, structure and charge) also play a major role in this process. We present knowledge gaps that need clarification such as the extent of DOM desorption from CNTs, the amount of co-adsorbed DOM during competition with small organic molecules for adsorption sites on the CNTs and the behavior of CNTs under realistic conditions. More data generated from experiments using natural DOM rather than dissolved humic substances are required to improve our understanding of the interactions between CNTs and small organic molecules in realistic environmental scenarios. This review provides conclusions and research directions needed to evaluate the nature of interactions between CNTs, DOM and organic pollutants in aquatic systems affected by anthropogenic activities.

Simple Method to Improve Electrical Conductivity of Films Made from Single-Walled Carbon Nanotubes

Despite the widespread use of sonication for individualization of nanomaterials, its destructive nature is rarely acknowledged. In this study, we demonstrated how exposure of the material to a hostile sound wave environment can be limited by the application of another preprocessing step. Single-walled carbon nanotubes (CNTs) were initially ground in a household coffee grinder, which enabled facile deagglomeration thereof. Such a simple approach enabled us to obtain high-quality CNT dispersion at reduced sonication time. Most importantly, electrical conductivity of free-standing films prepared from these dispersion was improved almost fourfold as compared with unground material eventually reaching 1067 ± 34 S/cm. This work presents a new approach as to how electrical properties of nanocarbon ensembles may be enhanced without the application of doping agents, the presence of which is often ephemeral.

Flexible Thermoelectric Materials and Generators: Challenges and Innovations

The urgent need for ecofriendly, stable, long-lifetime power sources is driving the booming market for miniaturized and integrated electronics, including wearable and medical implantable devices. Flexible thermoelectric materials and devices are receiving increasing attention, due to their capability to convert heat into electricity directly by conformably attaching them onto heat sources. Polymer-based flexible thermoelectric materials are particularly fascinating because of their intrinsic flexibility, affordability, and low toxicity. There are other promising alternatives including inorganic-based flexible thermoelectrics that have high energy-conversion efficiency, large power output, and stability at relatively high temperature. Herein, the state-of-the-art in the development of flexible thermoelectric materials and devices is summarized, including exploring the fundamentals behind the performance of flexible thermoelectric materials and devices by relating materials chemistry and physics to properties. By taking insights from carrier and phonon transport, the limitations of high-performance flexible thermoelectric materials and the underlying mechanisms associated with each optimization strategy are highlighted. Finally, the remaining challenges in flexible thermoelectric materials are discussed in conclusion, and suggestions and a framework to guide future development are provided, which may pave the way for a bright future for flexible thermoelectric devices in the energy market.

Dispersion, sedimentation and aggregation of multi-walled carbon nanotubes as affected by single and binary mixed surfactants

Two commonly used dispersants, octyl phenol ethoxylate (Triton X-100) and sodium dodecyl sulfate (SDS), were employed to explore the effects of single or mixed surfactants on the dispersion, sedimentation and aggregation of multi-walled carbon nanotubes (MWCNTs). Non-ionic surfactant TX100 showed much superior capability to anionic surfactant SDS in dispersing MWCNTs due to the benzene ring structure in its tail group. The addition of SDS reduced the adsorption of TX100 on the surface of MWCNTs and the consequent suspension of MWCNTs. The dispersing ability of TX100-SDS binary mixture was between those of individual SDS and TX100. The introduction of SDS greatly retarded the sedimentation and aggregation of suspended MWCNTs. The critical coagulation concentration (CCC) values of suspended MWCNTs dispersed by TX100 (2000 mg l-1), SDS (2000 mg l-1) and TX100-SDS (2000 mg l-1 of each component) were 48.6, 398 and 324 mM, respectively, for Na+ treatments. The CCC values were much lower for Ca2+ treatments, which were 30.4 and 32.1 mM, respectively, for MWCNTs dispersed by TX100 and TX100-SDS mixture. Overall, these results demonstrated that although the introduction of SDS did not improve the ability of TX100 in suspending MWCNTs, the suspensions exhibited more stable properties than those dispersed by TX100 alone. Our findings have important implications for the design of surfactant mixtures and the prediction of the behaviour and fate of MWCNTs in the water environment.

Imaging Method for Measurements of Particle Density and Solid Holdup of Entangled MWCNTs in a Fluidized Bed

A measurement method of the apparent particle density of the carbon nanotube (CNT) particles, characterized by enveloped volume formed by loosely entangled nanotubes, has been proposed for the CNT fluidized bed application. The method is characterized by obtaining the enveloped volume from the CNTs imaging under the free falling condition similar to the fluidized bed. The shape of the falling CNT particles in a column (0.1 m long × 0.012 m wide × 0.60 m high) was photographed using a high-speed camera under the sedimentation condition, and the apparent CNT particle density was calculated from the enveloped volume obtained by image-processing for the particles images. The apparent densities and solid holdups by the imaging method at various conditions were compared with those by the previous Hg-porosimetry method for the two types of CNTs (a vertically aligned CNT and two entangle CNTs) and the nonporous polycarbonate particle (a reference particle). The imaging method reflects well the packed bed and fluidized bed phenomena observed in the experiments with reasonable solid holdups, compared with the Hg-porosimetry method showing high densities and low holdups. The sizes of CNT particles predicted with the density by the imaging method were in good agreement with the measured mean particle sizes when calculated based on the Richardson–Zaki equation, indicating the imaging method represented well the enveloped volume and shape formed by entangled nanotubes on the CNTs.

Synthesis and characterization of DGEBA composites reinforced with Cu/Ag modified carbon nanotubes

Carbon nanotubes (CNTs) are among the strongest and stiffest contender to be used as filler to elevate the properties of epoxy. The aim of this research work is to evaluate the structural, thermal, and morphological properties of multiwalled carbon nanotubes (MWCNTs) hybridized with silver, copper and silver/copper nanoparticles (Ag/CuNP) obtained via chemical reduction of aqueous salts assisted with sodium dodecyl sulphate (SDS) as stabilizing agent. The MWCNTs/NP was further incorporated in DGEBA (epoxy) using ethyl cellulose as hardener. Scanning electron microscopy (SEM) reveals micro structural analysis of the MWCNTs/NP hybrids. The Fourier transform infrared (FTIR) spectra prove the interactions between the NP and MWCNTs. Thermogravimetric analysis (TGA) shows that the MWCNTs/NP hybrids decompose at a much faster rate and the weight loss decreased considerably due to the presence of NP. X-ray diffraction (XRD) confirms the formation of NP on the surface of MWCNTs and X-ray photoelectron spectroscopy (XPS) confirms the full covering of MWCNTs/NP hybrids with DGEBA.

Surfactants with aromatic headgroups for optimizing properties of graphene/natural rubber latex composites (NRL): Surfactants with aromatic amine polar heads

HYPOTHESIS

The compatibility of surfactants and graphene surfaces can be improved by increasing the number of aromatic groups in the surfactants. Including aniline in the structure may improve the compatibility between surfactant and graphene further still. Surfactants can be modified by incorporating aromatic groups in the hydrophobic chains or hydrophilic headgroups. Therefore, it is of interest to investigate the effects of employing anilinium based surfactants to disperse graphene nanoplatelets (GNPs) in natural rubber latex (NRL) for the fabrication of electrically conductive nanocomposites.

EXPERIMENTS

New graphene-philic surfactants carrying aromatic moieties in the hydrophilic headgroups and hydrophobic tails were synthesized by swapping the traditional sodium counterion with anilinium. ¹H NMR spectroscopy was used to characterize the surfactants. These custom-made surfactants were used to assist the dispersion of GNPs in natural rubber latex matrices for the preparation of conductive nanocomposites. The properties of nanocomposites with the new anilinium surfactants were compared with commercial sodium surfactant sodium dodecylsulfate (SDS), sodium dodecylbenzenesulfonate (SDBS), and the previously synthesized aromatic tri-chain sodium surfactant TC3Ph3 (sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3phenylpropoxy)carbonyl) pentane-2-sulfonate). Structural properties of the nanocomposites were studied using Raman spectroscopy, field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM). Electrical conductivity measurements and Zeta potential measurements were used to assess the relationships between total number of aromatic groups in the surfactant molecular structure and nanocomposite properties. The self-assembly structure of surfactants in aqueous systems and GNP dispersions was assessed using small-angle neutron scattering (SANS).

FINDINGS

Among these different surfactants, the anilinium version of TC3Ph3 namely TC3Ph3-AN (anilinium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3phenylpropoxy)carbonyl) pentane-2-sulfonate) was shown to be highly efficient for dispersing GNPs in the NRL matrices, increasing electrical conductivity eleven orders of magnitude higher than the neat rubber latex. Comparisons between the sodium and anilinium surfactants show significant differences in the final properties of the nanocomposites. In general, the strategy of increasing the number of surfactant-borne aromatic groups by incorporating anilinium ions in surfactant headgroups appears to be effective.

Vial sonication and ultrasonic immersion probe sonication to generate stable dispersions of multiwall carbon nanotubes for physico-chemical characterization and biological testing

Nanotechnology is considered to be a key enabling technology and in recent years there has been much growth in the use of nanostructured materials in industrial applications and in consumer products. It is, therefore, important that prior to being commercialized in consumer products, engineered nanomaterials are subjected to a thorough physico-chemical characterization as part of broader risk assessment to evaluate their possible effects on human health and the environment. The proper dispersion of nanomaterials sourced as powders becomes a first crucial step in the characterization process. This paper focuses on the dispersion of multiwall carbon nanotubes - often hydrophobic and tangled - since it may be challenging to re-disperse them effectively in aqueous media prior to characterization. A comparison has been made of non-contact vial sonication and immersion probe sonication using tannic acid as a dispersant. Transmission electron microscopy and UV-Vis spectroscopy were the techniques used to evaluate the dispersions. We used High Content Imaging and Colony Forming Efficiency to perform in vitro cytotoxicity studies on Human Alveolar Epithelial cells. It was found that both sonication treatments produce equivalent stable dispersions. No cytotoxic effects from MWCNTs were observed although some toxicity was observed and attributed to excess of the tannic acid dispersant.

Corrosion Evaluation of 316L Stainless Steel in CNT-Water Nanofluid: Effect of CNTs Loading

Polarization resistance and potentiodynamic scan testing were performed on 316L stainless steel (SS) at room temperature in carbon nanotube (CNT)-water nanofluid. Different CNT loadings of 0.05, 0.1, 0.3 and 0.5 wt% were suspended in deionized water using gum arabic (GA) surfactant. Corrosion potential, Tafel constants, corrosion rates and pitting potential values indicated better corrosion performance in the presence of CNTs with respect to samples tested in GA-water solutions. According to Gibbs free energy of adsorption, CNTs were physically adsorbed into the surface of the metal, and this adsorption followed Langmuir adsorption isotherm type II. Samples tested in CNT nanofluid revealed a corrosion performance comparable to that of tap water and better than that for GA-water solutions. Among all samples tested in CNT nanofluids, the lowest corrosion rate was attained with 0.1 wt% CNT nanofluid, while the highest value was obtained with 0.5 wt% CNT nanofluid. At higher CNT concentrations, accumulated CNTs might form active anodic sites and increase the corrosion rate. SEM images for samples of higher CNT loadings were observed to have higher pit densities and diameters.

Nanomaterials in Advanced, High-Performance Aerogel Composites: A Review

Aerogels are one of the most interesting materials of the 21st century owing to their high porosity, low density, and large available surface area. Historically, aerogels have been used for highly efficient insulation and niche applications, such as interstellar particle capture. Recently, aerogels have made their way into the composite universe. By coupling nanomaterial with a variety of matrix materials, lightweight, high-performance composite aerogels have been developed for applications ranging from lithium-ion batteries to tissue engineering materials. In this paper, the current status of aerogel composites based on nanomaterials is reviewed and their application in environmental remediation, energy storage, controlled drug delivery, tissue engineering, and biosensing are discussed.

Novel chemical route for CeO2/MWCNTs composite towards highly bendable solid-state supercapacitor device

Electrode materials having high capacitance with outstanding stability are the critical issues for the development of flexible supercapacitors (SCs), which have recently received increasing attention. To meet these demands, coating of CeO₂ nanoparticles have been performed onto MWCNTs by using facile chemical bath deposition (CBD) method. The formed CeO₂/MWCNTs nanocomposite exhibits excellent electrochemical specific capacitance of 1215.7 F/g with 92.3% remarkable cyclic stability at 10000 cycles. Light-weight flexible symmetric solid-state supercapacitor (FSSC) device have been engineered by sandwiching PVA-LiClO₄ gel between two CeO₂/MWCNTs electrodes which exhibit an excellent supercapacitive performance owing to the integration of pseudocapacitive CeO₂ nanoparticles onto electrochemical double layer capacitance (EDLC) behaved MWCNTs complex web-like structure. Remarkable specific capacitance of 486.5 F/g with much higher energy density of 85.7 Wh/kg shows the inherent potential of the fabricated device. Moreover, the low internal resistance adds exceptional stability along with unperturbed behavior even under high mechanical stress which can explore its applicability towards high-performance flexible supercapacitor for advanced portable electronic devices.

Gemini surfactants as efficient dispersants of multiwalled carbon nanotubes: Interplay of molecular parameters on nanotube dispersibility and debundling

Surfactants have been widely employed to debundle, disperse and stabilize carbon nanotubes in aqueous solvents. Yet, a thorough understanding of the dispersing mechanisms at molecular level is still warranted. Herein, we investigated the influence of the molecular structure of gemini surfactants on the dispersibility of multiwalled carbon nanotubes (MWNTs). We used dicationic n-s-n gemini surfactants, varying n and s, the number of alkyl tail and alkyl spacer carbons, respectively; for comparisons, single-tailed surfactant homologues were also studied. Detailed curves of dispersed MWNT concentration vs. surfactant concentration were obtained through a stringently controlled experimental procedure, allowing for molecular insight. The gemini are found to be much more efficient dispersants than their single-tailed homologues, i.e. lower surfactant concentration is needed to attain the maximum dispersed MWNT concentration. In general, the spacer length has a comparatively higher influence on the dispersing efficiency than the tail length. Further, scanning electron microscopy imaging shows a sizeable degree of MWNT debundling by the gemini surfactants in the obtained dispersions. Our observations also point to an adsorption process that does not entail the formation of micelle-like aggregates on the nanotube surface, but rather coverage by individual molecules, among which the ones that seem to be able to adapt best to the nanotube surface provide the highest efficiency. These studies are relevant for the rational design and choice of optimal dispersants for carbon nanomaterials and other similarly water-insoluble materials.

Printed Diodes: Materials Processing, Fabrication, and Applications

Printing techniques for the fabrication of diodes have received increasing attention over the last decade due to their great potential as alternatives for high-throughput and cost-effective manufacturing approaches compatible with both flexible and rigid substrates. Here, the progress achieved and the challenges faced in the fabrication of printed diodes are discussed and highlighted, with a focus on the materials of significance (silicon, metal oxides, nanomaterials, and organics), the techniques utilized for ink deposition (gravure printing, screen printing, inkjet printing, aerosol jet printing, etc.), and the process through which the printed layers of diode are sintered after printing. Special attention is also given to the device applications within which the printed diodes have been successfully incorporated, particularly in the fields of rectification, light emission, energy harvesting, and displays. Considering the unmatched production scalability of printed diodes and their intrinsic suitability for flexible and wearable applications, significant improvement in performance and intensive research in development and applications of the printed diodes will continuously progress in the future.

Synergistic Effect on the Thermomechanical and Electrical Properties of Epoxy Composites with the Enhancement of Carbon Nanotubes and Graphene Nano Platelets

The synergetic effect of adding multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) on the thermomechanical properties and electric resistance of epoxy polymers were experimentally analyzed in this study. The total content of two employed carbon fillers were kept constant at 0.4 wt %, and seven filler ratios between two fillers (MWCNTs:GNPs), i.e., 10:0, 1:9, 3:7, 5:5, 7:3, 9:1, and 0:10, were considered in the experimental program to investigate the influences of employed nano-filler ratios on the viscoelastic and electrical properties of the studied nanocomposites. The thermomechanical properties and the sheet resistance of the nanocomposites were analyzed using a dynamic mechanical analyzer and four-point probe, respectively. Moreover, the thermogravimetric analyzer was utilized to measure the pyrolysis temperature of the nanocomposites. Experimental results show that the synergistic effect of adding two nano-fillers were clear for the improvement of the storage moduli, glass transition temperatures, and electric conductivity. Oppositely, the employment of two fillers has a slight effect on the pyrolysis temperatures of the studied nanocomposites. The composites with the MWCNT:GNP ratio of 1:9 display the most apparent enhancement of the thermomechanical properties. The improvement results from the uniform distribution and the high aspect ratio of GNPs. The addition of a small amount of MWCNTs provides more linkage in the matrix. Moreover, the specimens with the MWCNT:GNP ratio of 1:9 shows remarkable electrical properties, which result from the large contact surface areas of GNPs with each other. The employment of few MWCNTs plays an important bridging role between the layered GNPs.

Anchoring conductive polymeric monomers on single-walled carbon nanotubes: towards covalently linked nanocomposites

Chemical functionalization with conductive polymeric monomers on carbon nanotubes carried out by a straightforward method.

A new approach for the achievement of stable aqueous dispersions of carbon nanotubes

A simple and innovative way to achieve highly stable aqueous dispersions of both multi- and single-walled carbon nanotubes is reported.

Multiscale Polymer Dynamics in Hierarchical Carbon Nanotube Grafted Glass Fiber Reinforced Composites

Carbon nanotube (CNT) grafted glass fiber reinforced epoxy nanocomposites (GFRP) present a range of stiffnesses (MPa to GPa) and length scales (μm to nm) at the fiber-matrix interface. The contribution of functionalized CNT networks to the local and bulk polymer dynamics is studied here by using a combination of torsion dynamical mechanical thermal analysis (DMTA), positron annihilation lifetime spectroscopy (PALS), and neutron scattering (NS) measurements. DMTA measurements highlight a reduction in the storage modulus (G') in the rubbery region and an asymmetric broadening of the loss modulus (G″) peak in the α-transition region. NS measurements show a suppressed hydrogen mean-square displacement (MSD) in the presence of glass fibers but a higher hydrogen MSD after grafting functionalized CNTs onto fiber surfaces. PALS measurements show greater free volume characteristics in the presence of the functionalized CNT modified composites, supporting the view that these interface layers increase polymer mobility. While NS and DMTA are sensitive to different modes of chain dynamics, the localization of functionalized nanotubes at the fiber interface is found to affect the distribution of polymer relaxation modes without significantly altering the thermally activated relaxation processes.

Natural Rubber Nanocomposites: A Review

This paper reviews studies carried out on natural rubber filled with nanofillers such as spherical silica particles (generated by the sol gel reaction), clays and carbon nanostructures. It is shown that the mechanical response of NR is influenced by several parameters including the processing conditions, the state of filler dispersion, the polymer-filler interactions and the filler morphological aspects. Even if the sol gel process conducted in vulcanized rubber yields almost ideal dispersions, rod-shaped particles such as clay, carbon fibers or carbon nanotubes are by far more efficient in terms of mechanical reinforcement on account of their anisotropic character and their ability to orientate in the direction of stretch. The efficiency of layered fillers such as clays or graphitic structures clearly depends on the way they are dispersed (exfoliated) in the rubber. Complete exfoliation still remains difficult to achieve which limits the tremendous nanoreinforcement expected from a single layer of clay or graphite. In all cases, the onset of crystallization is observed at a lower strain value than that of the unfilled matrix due to strain amplification effects.

The role of surfactants in wastewater treatment: Impact, removal and future techniques: A critical review

Wastewater treatment has an important responsibility to react to changing consumer and industrial produced wastes that pose environmental challenges. Surfactants are one of these emerging contaminants. They are of interest because of their increasingly ubiquitous domestic and industrial use and the difficulty their presence causes traditional treatment. In response to this developing area, this critical review considers research from a variety of technical backgrounds to provide an up to date overview of the impact of surfactants on the environment, health and their removal. This found major concerns about surfactants on the environment and on health being corroborated in the past five years. Current research into removal focuses on existing biological and chemical wastewater treatment optimisation. Despite improvements being found to traditional biological methods using chemical pre-treatments there is a clear lack of consensus regarding the ideal strategy. Drawbacks and potential solutions for a range of these technologies, including Fenton reaction and aerobic degradation, are discussed. In this field the authors recommend an improved diversity in surfactants used for the research and addressing of significant knowledge gaps. Novel methods, such as Carbon Nanotube (CNT) use are also discussed. These methods, while showing promising results, will require continual research effort to resolve present issues such as variable performance and environmental concerns. Larger scale work is also needed to validate the initial work done. Potential uses of surfactants to optimise wastewater treatment, such as Surfactant Modified Zeolites (SMZs), are also discussed. This review finds that surfactant removal from wastewater is a promising and challenging field that warrants further investigation.