Chromium determination and speciation since 2000

Biosorption of hexavalent chromium from aqueous medium with Opuntia biomass

The biosorption of hexavalent chromium from aqueous solutions by Opuntia cladodes and ectodermis from cactus fruits was investigated. Both types of biomass are considered low-cost, natural, and ecofriendly biosorbents. Batch experiments were carried out to determine Cr(VI) biosorption capacity and the efficiency of the biosorption process under different pH, initial Cr(VI) concentration, and sorbent dosage. The biosorption of Cr(VI) by Opuntia biomass was highly pH dependent, favoring higher metal uptake at low pH. The higher biosorption capacity was exhibited at pH 2. The optimal conditions were obtained at a sorbent dosage of 1 g L(-1) and initial metal concentration of 10 mg L(-1). Biosorption kinetic data were properly fitted with the pseudo-second-order kinetic model. The rate constant, the initial biosorption rate, and the equilibrium biosorption capacity were determined. The experimental equilibrium data obtained were analyzed using two-parameter isotherm models (Langmuir, Freundlich, and Temkin). The Langmuir maximum monolayer biosorption capacity (q max) was 18.5 mg g(-1) for cladodes and 16.4 mg g(-1) for ectodermis. The results suggest that Opuntia biomass could be considered a promising low-cost biosorbent for the ecofriendly removal of Cr(VI) from aqueous systems.

Flow injection analysis of trace chromium (VI) in drinking water with a liquid waveguide capillary cell and spectrophotometric detection

Hexavalent chromium (Cr(VI)) is an acknowledged hazardous material in drinking waters. As such, effective monitoring and assessment of the risks posed by Cr(VI) are important analytical objectives for both human health and environmental science. However, because of the lack of highly sensitive, rapid, and simple procedures, a relatively limited number of studies have been carried out in this field. Here we report a simple and sensitive analytical procedure of flow injection analysis (FIA) for sub-nanomolar Cr(VI) in drinking water samples with a liquid core waveguide capillary cell (LWCC). The procedure is based on a highly selective reaction between 1, 5-diphenylcarbazide and Cr(VI) under acidic conditions. The optimized experimental parameters included reagent concentrations, injection volume, length of mixing coil, and flow rate. Measurements at 540 nm, and a 650-nm reference wavelength, produced a 0.12-nM detection limit. Relative standard deviations for 1, 2, and 10 nM samples were 5.6, 3.6, and 0.72 % (n = 9), and the analysis time was <2 min sample(-1). The effects of salinity and interfering ions, especially Fe(III), were evaluated. Using the FIA-LWCC method, different sources of bottled waters and tap waters were examined. The Cr(VI) concentrations of the bottled waters ranged from the detection limit to ∼20 nM, and tap waters collected from the same community supply had Cr(VI) concentration around 14 nM.

Determination of trace chromium (VI) using a hollow-core metal-cladding optical waveguide sensor

A biosensor capable of highly sensitive detection of trace chromium (VI) with a simple hollow-core metal-cladding waveguide (HCMW) structure is theoretically modeled and experimentally demonstrated. Owing to the high sensitivity of the excited ultrahigh-order modes in the waveguide, a tiny variation of the extinction coefficients in the waveguide guiding layer where the chromate ions reacts with the diphenylcarbazide (DPC) can lead to a significant change of light intensity in the reflection spectrum. The experimental results indicate that using the proposed method, the chromium (VI) sensitivity detection limit can be as low as 1.2 nM, which represents a 16-fold improvement compared to the surface plasmon field-enhanced resonance light scattering (SP-RLS) method, and a 4-fold improvement compared to the flame atomic absorption spectrometry and fluorimetry spectroscopy, respectively.

Improved Bi Film Wrapped Single Walled Carbon Nanotubes for Ultrasensitive Electrochemical Detection of Trace Cr(VI)

We report here the successful fabrication of an improved Bi film wrapped single walled carbon nanotubes modified glassy carbon electrode (Bi/SWNTs/GCE) as a highly sensitive platform for ultratrace Cr(VI) detection through catalytic adsorptive cathodic stripping voltammetry (AdCSV). The introduction of negatively charged SWNTs extraordinarily decreased the size of Bi particles to nanoscale due to electrostatic interaction which made Bi(III) cations easily attracted onto the surface of SWNTs in good order, leading to higher quality of Bi film deposition. The obtained Bi/SWNTs composite was well characterized with electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), the static water contact angle and the voltammetric measurements. The results demonstrates the improvements in the quality of Bi film deposited on the surface of SWNTs such as faster speed of electron transfer, more uniform and smoother morphology, better hydrophilicity and higher stripping signal. Using diethylene triaminepentaacetic acid (DTPA) as complexing ligand, the fabricated electrode displays a well-defined and highly sensitive peak for the reduction of Cr(III)-DTPA complex at -1.06 V (vs. Ag/AgCl) with a linear concentration range of 0-25 nM and a fairly low detection limit of 0.036 nM. No interference was found in the presence of coexisting ions, and good recoveries were achieved for the analysis of a river sample. In comparison to previous approaches using Bi film modified GCE, the newly designed electrode exhibits better reproducibility and repeatability towards aqueous detection of trace Cr(VI) and appears to be very promising as the basis of a highly sensitive and selective voltammetric procedure for Cr(VI) detection at trace level in real samples.

Development of experimental design approach and ANN-based models for determination of Cr(VI) ions uptake rate from aqueous solution onto the solid biodiesel waste residue

In the present work, the evaluation capacities of two optimization methodologies such as RSM and ANN were employed and compared for predication of Cr(VI) uptake rate using defatted pongamia oil cake (DPOC) in both batch and column mode. The influence of operating parameters was investigated through a central composite design (CCD) of RSM using Design Expert 8.0.7.1 software. The same data was fed as input in ANN to obtain a trained the multilayer feed-forward networks back-propagation algorithm using MATLAB. The performance of the developed ANN models were compared with RSM mathematical models for Cr(VI) uptake rate in terms of the coefficient of determination (R(2)), root mean square error (RMSE) and absolute average deviation (AAD). The estimated values confirm that ANN predominates RSM representing the superiority of a trained ANN models over RSM models in order to capture the non-linear behavior of the given system.

Preconcentration and speciation of Cr(III) and Cr(VI) in water and soil samples by spectrometric detection via use of nanosized alumina-coated magnetite solid phase

A novel nanomaterial has been developed for speciation of Cr(III) and Cr(VI) in water and soil samples. In this study, a new type of alumina-coated magnetite nanoparticles (Fe3O4/Al2O3 NPs) modified by the surfactant Triton X-114 has been successfully synthesized and used in magnetic mixed hemimicelles solid-phase extraction procedure. The procedure was based on the reaction of chromium(III) with 1-(2-pyridilazo)-2-naphtol as a ligand, yielding a complex, which was entrapped "in situ" in the surfactant hemimicelles. The concentration of chromium(III) was determined using flame atomic absorption spectrometry. After reduction of Cr(VI) to Cr(III) by ascorbic acid, the system was applied to the total chromium. Cr(VI) was then calculated as the difference between the total Cr and the Cr(III) content. This method can also be used for complicated matrices such as soil samples without any special pretreatment. Under the optimum conditions of parameters, the recoveries of Cr(III) by analyzing the spiked water and soil samples were between 98.6 and 100.8 % and between 96.5 and 100.7 %, respectively. Detection limits of Cr(III) were between 1.4 and 3.6 ng mL(-1) for water samples and 5.6 ng mg(-1) for soil samples.

Cr(VI) reduction by a potent novel alkaliphilic halotolerant strain Pseudochrobactrum saccharolyticum LY10

A novel Cr(VI)-reducing strain, Pseudochrobactrum saccharolyticum LY10, was isolated and characterized for its high Cr(VI)-reducing ability. Strain LY10 had typical characteristics of alkali-tolerance and halotolerance. Kinetic analysis indicated that the maximum reduction rate was achieved under optimum conditions with initial pH 8.3, 20gL(-1) NaCl, 55mgL(-1) Cr(VI), and 1.47×10(9)cellsmL(-1) of cell concentration. Further mechanism studies verified that the removal of Cr(VI) was mainly achieved by a metabolism-dependent bioreduction process. Strain LY10 accumulated chromium both in and around the cells, with cell walls acting as the major binding sites for chromium. X-ray absorption near-edge structure (XANES) analysis further confirmed that the chromium immobilized by the cells was in the Cr(III) state. In the present study, Pseudochrobactrum saccharolyticum was, for the first time, reported to be a Cr(VI)-reducing bacteria. Results from this research would provide a potential candidate for bioremediation of Cr(VI)-contaminated environments, especially alkaline and saline milieus with Cr(VI) at low-to-mid concentrations.

Synthesis of Ce3+ doped ZnFe2O4 self-assembled clusters and adsorption of chromium(VI)

A solvothermal synthetic route was used to prepare Ce(3+) doped Zn ferrites, where sphere-like clusters aggregated by nanosized particles were fabricated. The size of the cluster and the saturation magnetization of the sample are decreasing with the increase of Ce(3+). These samples can be easily separated from aqueous solutions by applying a magnetic field and have a high loading capacity of Cr(VI). The Cr(VI) adsorption experiments indicated that the adsorption was divided into two processes, in which the first one took place about 6h, the second one took place between 6 and 96 h. The maximum adsorption capacity for Cr(VI) was determined to be 57.24 mg/g. Langmuir model was employed to fit the adsorption isotherm, which implied the single layer adsorption. The data of SBET, external area and porous area of the samples can be used to explain these adsorption processes. And the Ce(3+) ions doped in the sample induced the increasing adsorption capacity of Cr(VI). The adsorption process can be described by the pseudo-second-order kinetic model.

Facile preparation of glutathione-stabilized gold nanoclusters for selective determination of chromium (III) and chromium (VI) in environmental water samples

A novel method for selective determination of Cr(III) and Cr(VI) in environmental water samples was developed based on target-induced fluorescence quenching of glutathione-stabilized gold nanoclusters (GSH-Au NCs). Fluorescent GSH-Au NCs were synthesized by a one-step approach employing GSH as reducing/protecting reagent. It was found that Cr(III) and Cr(VI) showed pH-dependent fluorescence quenching capabilities for GSH-Au NCs, and thus selective determination of Cr(III) and Cr(VI) could be achieved at different pHs. Addition of EDTA was able to effectively eliminate the interferences from other metal ions, leading to a good selectivity for this method. Under optimized conditions, Cr(III) showed a linear range of 25-3800 μg L(-1) and a limit of detection (LOD) of 2.5 μg L(-1). The Cr(VI) ion demonstrated a linear range of 5-500 μg L(-1) and LOD of 0.5 μg L(-1). The run-to-run relative standard deviations (n=5) for Cr(III) and Cr(VI) were 3.9% and 2.8%, respectively. The recoveries of Cr(III) and Cr(VI) in environmental water samples were also satisfactory (76.3-116%). This method, with its simplicity, low cost, high selectivity and sensitivity, could be used as a promising tool for chromium analysis in environmental water samples.

Characterization of chromium species in urban runoff

Little is known about the presence of the element Cr in its toxic hexavalent form Cr(VI) in stormwater runoff from urban areas. Most studies report only total Cr concentration, i.e., including also the nontoxic Cr(III) molecular form. The objective of this study was to evaluate a field method based on cation-exchange for characterization of Cr species in urban stormwater runoff and soil leachate. We used a 0.05 mol L Na and Ca solution and a soil leachate as matrices and spiked these with Cr(III), Cr(VI), or both in the concentration range of 1 to 100 μg L. We then filtered the test samples through cation-exchange cartridges. In the Na-Ca salt matrix, the Cr(III) was retained 100% and recovery values of Cr(VI) were 86 to 100%. Furthermore, in such a matrix, each cartridge could be reused at least nine times without a drop in retention of Cr(III) or recovery of Cr(VI). In a soil leachate matrix, the method appeared less applicable. Apparently Cr(III) forms complexes with dissolved organic matter, allowing it to bypass the cartridge, resulting in incomplete Cr(III) retention and thus incomplete speciation. The complexes are formed rapidly after spiking, thus changes in the Cr-species distribution are likely to occur within a few hours when fresh samples are stored. Furthermore, we concluded that Cr(III) at neutral pH in pure solution or complexed with dissolved organic C can sorb irreversibly to polyethylene and polypropylene containers. Our findings show that there is still a need for a method that can be applied to urban runoff in the field. Furthermore, cartridge speciation methods should ideally be tested before being applied on solutions containing organic matter.

Chromium speciation in river sediment pore water contaminated by tannery effluent

Cr(VI) is far more soluble and toxic than Cr(III). Sediment pore water was investigated in a river adjacent to the property of a large former tannery, into which Cr-contaminated effluent was discharged over a 55-year period, and where extremely high Cr concentrations have been found in the sediments. Dialysis cells, or peepers, were used to generate depth profiles of Cr concentration in sediment pore water. Samples were analyzed for total Cr using inductively coupled plasma-mass spectrometry (ICP-MS) and for Cr species using high performance liquid chromatography (HPLC)-ICP-MS. The results show an absence of Cr(VI) in all samples. Furthermore, incomplete recovery of Cr(VI) added to the samples collected at the locations with highest sediment Cr concentrations indicate strong reducing conditions at those locations, which are not conducive to the presence of Cr(VI).

Determination of nanomolar chromate in drinking water with solid phase extraction and a portable spectrophotometer

Determination of chromate at low concentration levels in drinking water is an important analytical objective for both human health and environmental science. Here we report the use of solid phase extraction (SPE) in combination with a custom-made portable light-emitting diode (LED) spectrophotometer to achieve detection of chromate in the field at nanomolar levels. The measurement chemistry is based on a highly selective reaction between 1,5-diphenylcarbazide (DPC) and chromate under acidic conditions. The Cr-DPC complex formed in the reaction can be extracted on a commercial C18 SPE cartridge. Concentrated Cr-DPC is subsequently eluted with methanol and detected by spectrophotometry. Optimization of analytical conditions involved investigation of reagent compositions and concentrations, eluent type, flow rate (sample loading), sample volume, and stability of the SPE cartridge. Under optimized conditions, detection limits are on the order of 3 nM. Only 50 mL of sample is required for an analysis, and total analysis time is around 10 min. The targeted analytical range of 0-500 nM can be easily extended by changing the sample volume. Compared to previous SPE-based spectrophotometric methods, this analytical procedure offers the benefits of improved sensitivity, reduced sample consumption, shorter analysis time, greater operational convenience, and lower cost.

Sequential eluent injection technique as a new approach for the on-line enrichment and speciation of Cr(III) and Cr(VI) species on a single column with FAAS detection

This paper introduces a sequential eluent injection (SEI) technique combined with an on-line preconcentration/separation system for a fast and sensitive FAAS determination of trace amounts of Cr(III) and Cr(VI) species. The method is based on the simultaneous retention of Cr(III) and Cr(VI) on a single mini-column packed with a chloromethylated polystyrene functionalized with N,N-bis(naphthylideneimino)diethylenetriamine (PS-NAPdien) at pH 6.7. The retained chromium species was eluted by sequential injection of HCl for desorption of Cr(III), and NH(3) and NH(4)NO(3) buffer solutions for desorption of Cr(VI). All the chemical and flow injection variables were optimized for the quantitative preconcentration and speciation of Cr(III) and Cr(VI). Under the optimum conditions, the calibration graph obtained is linear over the concentration range of 2.0-60.0μg L(-1) for Cr(III), and 8.0-180.0μg L(-1) for Cr(VI). The preconcentration factors for Cr(III) and Cr(VI) were 70 and 30, respectively. The 3σ detection limits were 0.6μg L(-1) and 2.5μg L(-1) for Cr(III) and Cr(VI), respectively. The relative standard deviations were 2.55% and 0.8%, respectively, for 6 replicate determinations of Cr(III) and Cr(VI) at the 40.0μg L(-1) level. The proposed method was applied for determination of Cr(III) and Cr(VI) in different water samples with satisfactory results.

9-Acridone-4-carboxylic acid as an efficient Cr(III) fluorescent sensor: trace level detection, estimation and speciation studies

9-Acridone-4-carboxylic acid has been established as an efficient Cr(III) fluorescent sensor. The binding of this ligand with Cr(III) is confirmed by FTIR, thermal and mass spectral analysis of the product. Based on this chelation assisted fluorescence quenching, a highly sensitive spectrofluorometric method is developed for trace level detection, estimation and speciation studies of chromium in DMF-water. The ligand has an excitation and emission maxima at 408 nm and 498.4 nm, respectively. The equilibrium binding constant of the ligand with Cr(III) is 8.1378 × 10(4) as calculated using Stern-Volmer equation. Up to 9 × 10(-6)mol L(-1) of [Cr(3+)], linearity has been observed. The interference of foreign ions has been found to be negligible.

Selective detection of nanomolar in aqueous solution based on functionalized gold nanoparticles

The determination of trace Cr(vi) is very important because of its highly carcinogenic and mutagenic effects. In this study, a colorimetric detection method based on 1,4-dithiothreitol functionalized gold nanoparticles (DTT-AuNPs) for nanomolar Cr(vi) in aqueous solution is reported. The method principle was based on the aggregation of DTT-AuNPs induced by Cr(vi), which led to red-shift of the surface plasmon resonance (SPR) peak of DTT-AuNPs. UV-vis absorption spectra, Zeta potentials, and transmission electron microscopy (TEM) images were used to demonstrate the aggregation of DTT-AuNPs. Some parameters affecting the detection including solution pH and DTT concentration were optimized. Under the optimized conditions, a good linear relationship (correlation coefficient r = 0.997 5) was obtained between the ratio (A650/520) of the absorbance at 650 nm to that at 520 nm and the concentration of Cr(vi) over the range of 100-600 nM, and the limit of detection (LOD) for Cr(vi) at a signal-to-noise ratio of 3 was 20 nM. The method showed selective detection toward Cr(vi) against other common metal ions in waters. Furthermore, the method developed was applied for detecting trace Cr(vi) in real water samples, with recoveries of 95%-115%.

Pyridine appended L-methionine: a novel chelating resin for pH dependent Cr speciation with scanning electron microscopic evidence and monitoring of yeast mediated green bio-reduction of Cr(VI) to Cr(III) in environmental samples

Chemical speciation and pH dependent separation of Cr(III) and Cr(VI) species in environmental samples have been achieved by solid phase extraction using a new chelating resin containing pyridine appended L-methionine. Cr(III) is completely sorbed on the resin at pH 8.0 and Cr(VI) at pH 2.0. Hence a pH dependent separation of Cr(III) and Cr(VI) is possible with a limit of detection of 1.6 μg mL(-1) and 0.6 μg mL(-1) respectively. The sorption capacity of the resin for Cr(III) and Cr(VI) is 2.8 mmol g(-1) and 1.3 mmol g(-1) respectively. The sorption of chromium on the resin is supported by scanning electron microscopy (SEM). Complete desorption of Cr(III) and Cr(VI) from 1g of Cr loaded resin was achieved using 10 mL of 2 mol L(-1) HNO(3) and 6 mL of 3 mol L(-1) HNO(3) respectively. Quantitative recoveries of Cr(III) (pH 8.0) and Cr(VI) (pH 2.0) were found to be 96.0% and 98.0% respectively. Reduction efficiency of Rhodotornula mucilaginosa yeast from Cr(VI) to Cr(III) was monitored with this new resin. Concentrations of metal ions were measured by flame atomic absorption spectroscopy (FAAS).

Simultaneous chromate reduction and azo dye decolourization by Brevibacterium casei: azo dye as electron donor for chromate reduction

Chromate [Cr(VI)] and azo dyes are common pollutants which may co-exist in some industrial effluents. Hence studies of biological treatment of industrial wastewater should include investigation of the co-removal of these two pollutants. Brevibacterium casei, which can reduce Cr(VI) in the presence of the azo dye Acid Orange 7 (AO7) under nutrient-limiting condition, was isolated from a sewage sludge sample of a dyeing factory. Response surface methodology, which is commonly used to optimize growth conditions for food microorganisms to maximize product(s) yield, was used to determine the optimal conditions for chromate reduction and dye decolourization by B. casei. The optimal conditions were 0.24 g/L glucose, 3.0 g/L (NH(4))(2)SO(4) and 0.2 g/L peptone at pH 7 and 35 degrees C. The predicted maximum chromate reduction efficiencies and dye decolourization were 83.4+/-0.6 and 40.7+/-1.7%, respectively. A new mechanism was proposed for chromate reduction coupling with AO7 decolourization by B. casei. Under nutrient-limiting condition, AO7 was used as an e(-) donor by the reduction enzyme(s) of B. casei for the reduction of Cr(VI). The resulted Cr(III) then complexed with the oxidized AO7 to form a purple coloured intermediate.

Use of activated carbon as a reactive support to produce highly active-regenerable Fe-based reduction system for environmental remediation

Composites based on iron supported on high surface area activated carbon were prepared and characterized with (57)Fe Mössbauer spectroscopy, X-ray diffraction, saturation magnetization measurements and temperature-programmed reduction. Upon thermal treatment, the supported iron oxides react with carbon to yield reduced chemical species, i.e. Fe(3)O(4) and Fe(0). This so produced composite was found to be highly efficient in two environmental applications: (i) degradation of textile dye and (ii) reduction of Cr(VI) in aqueous medium. Sequential reuses evidenced a progressive chemical deactivation of the composites due to a corresponding oxidation of the reactive species. Even after being virtually deactivated, the initial chemical reducing ability of the composites can be regenerated by heating at 800 degrees C under N(2) atmosphere, and then reused for several consecutive times.

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1M Na(2)CO(3) and filtered through hydrophilic PDVF 0.45 microm filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 microg g(-1) (cyclone dust), 2710 microg g(-1) (fine dust), and 7800 microg g(-1) (slimes dust) which exceeded the maximum acceptable risk concentration (20 microg g(-1)). The concentration of Cr(VI) in environmental samples of grass (3.4+/-0.2), soil (7.7+/-0.2), and tree bark (11.8+/-1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

Spectrophotometric method for the determination of chromium (VI) in water samples

A simple and sensitive spectrophotometric method for the determination of chromium has been developed. The method is based on the diazotization of Dapsone in hydroxylamine hydrochloride medium and coupling with N-(1-Napthyl) Ethylene Diamine Dihydrochloride by electrophilic substitution to produce an intense pink azo-dye, which has absorption maximum at 540 nm. The Beer's law is obeyed from 0.02-1.0 microg mL(-1) and the molar absorptivity is 3.4854 L mol(-1) cm(-1). The Limits of quantification and Limit of detection of the proposed method are 0.0012 microg mL(-1) and 0.0039 microg mL(-1) respectively. The method has been successfully applied for the determination of chromium in water samples and the results were statistically evaluated with that of the reference method.