Interstitial flow and its effects in soft tissues

Migration dynamics of breast cancer cells in a tunable 3D interstitial flow chamber

The migration of cells such as leukocytes, tumor cells, and fibroblasts through 3D matrices is critical for regulating homeostasis and immunity and for driving pathogenesis. Interstitial flow through the extracellular matrix, which can substantially increase during inflammation and in the tumor microenvironment, can influence cell migration in multiple ways. Leukocytes and tumor cells are heterogeneous in their migration responses to flow, yet most 3D migration studies use endpoint measurements representing average characteristics. Here we present a robust new microfluidic device for 3D culture with live imaging under well-controlled flow conditions, along with a comparison of analytical methods for describing the migration behavior of heterogeneous cell populations. We then use the model to provide new insight on how interstitial flow affects MDA-MB-231 breast cancer cell invasion, phenomena that are not seen from averaged or endpoint measurements. Specifically, we find that interstitial flow increases the percentage of cells that become migratory, and increases migrational speed in about 20% of the cells. It also increases the migrational persistence of a subpopulation (5-10% of cells) in the positive or negative flow direction. Cells that migrated upstream moved faster but with less directedness, whereas cells that migrated in the direction of flow moved at slower speeds but with higher directedness. These findings demonstrate how fluid flow in the tumor microenvironment can enhance tumor cell invasion by directing a subpopulation of tumor cells in the flow direction; i.e., towards the draining lymphatic vessels, a major route of metastasis.

The attachments of the temporomandibular joint disc: a biochemical and histological investigation

OBJECTIVE

The complex movement of the temporomandibular joint (TMJ) disc during mastication is controlled in large part by the disc's attachments to the surrounding tissues. This study seeks to address the lack of available quantitative data characterizing the extracellular matrix composition of the discal attachments and how these properties compare to the disc.

DESIGN

Porcine TMJ disc-attachment complexes were carefully dissected into six discal attachments and five TMJ disc regions. All samples were assayed biochemically for total collagen, glycosaminoglycan (GAG), DNA, and hydration. Additionally, histology was performed on the whole joint to investigate the anatomy of the disc-attachment complex, and to verify the regional distribution of matrix components.

RESULTS

Quantitative biochemical assays showed that overall water content was fairly constant in all disc and attachment regions. Disc regions generally showed higher sulfated GAG and collagen content than the attachments. In contrast, the attachments contained greater DNA content than the disc. Histological staining supported the quantitative results and also indicated more elastic fibres to be present in the attachments than the disc.

CONCLUSIONS

Although macroscopically the TMJ disc and its attachments form a seamless complex within the joint, a closer look at regional biochemical constituents reveals that these two components are distinct. Whilst the disc and attachments both contain the same major constituents, the relative amounts of these components vary based on the functional requirements of the tissue. These results can further understanding of both TMJ biology and pathology.

Multiscale modeling of lymphatic drainage from tissues using homogenization theory

Lymphatic capillary drainage of interstitial fluid under both steady-state and inflammatory conditions is important for tissue fluid balance, cancer metastasis, and immunity. Lymphatic drainage function is critically coupled to the fluid mechanical properties of the interstitium, yet this coupling is poorly understood. Here we sought to effectively model the lymphatic-interstitial fluid coupling and ask why the lymphatic capillary network often appears with roughly a hexagonal architecture. We use homogenization method, which allows tissue-scale lymph flow to be integrated with the microstructural details of the lymphatic capillaries, thus gaining insight into the functionality of lymphatic anatomy. We first describe flow in lymphatic capillaries using the Navier-Stokes equations and flow through the interstitium using Darcy's law. We then use multiscale homogenization to derive macroscale equations describing lymphatic drainage, with the mouse tail skin as a basis. We find that the limiting resistance for fluid drainage is that from the interstitium into the capillaries rather than within the capillaries. We also find that between hexagonal, square, and parallel tube configurations of lymphatic capillary networks, the hexagonal structure is the most efficient architecture for coupled interstitial and capillary fluid transport; that is, it clears the most interstitial fluid for a given network density and baseline interstitial fluid pressure. Thus, using homogenization theory, one can assess how vessel microstructure influences the macroscale fluid drainage by the lymphatics and demonstrate why the hexagonal network of dermal lymphatic capillaries is optimal for interstitial tissue fluid clearance.

Infusion pressure and pain during microneedle injection into skin of human subjects

Infusion into skin using hollow microneedles offers an attractive alternative to hypodermic needle injections. However, the fluid mechanics and pain associated with injection into skin using a microneedle have not been studied in detail before. Here, we report on the effect of microneedle insertion depth into skin, partial needle retraction, fluid infusion flow rate and the co-administration of hyaluronidase on infusion pressure during microneedle-based saline infusion, as well as on associated pain in human subjects. Infusion of up to a few hundred microliters of fluid required pressures of a few hundred mmHg, caused little to no pain, and showed weak dependence on infusion parameters. Infusion of larger volumes up to 1 mL required pressures up to a few thousand mmHg, but still usually caused little pain. In general, injection of larger volumes of fluid required larger pressures and application of larger pressures caused more pain, although other experimental parameters also played a significant role. Among the intradermal microneedle groups, microneedle length had little effect; microneedle retraction lowered infusion pressure but increased pain; lower flow rate reduced infusion pressure and kept pain low; and use of hyaluronidase also lowered infusion pressure and kept pain low. We conclude that microneedles offer a simple method to infuse fluid into the skin that can be carried out with little to no pain.

Sensitivity analysis of an image-based solid tumor computational model with heterogeneous vasculature and porosity

An MR image-based computational model of a murine KHT sarcoma is presented that allows the calculation of plasma fluid and solute transport within tissue. Such image-based models of solid tumors may be used to optimize patient-specific therapies. This model incorporates heterogeneous vasculature and tissue porosity to account for nonuniform perfusion of an MR-visible tracer, gadolinium-diethylenetriamine pentaacetic acid (Gd-DTPA). Dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI) was conducted following intravenous infusion of Gd-DTPA to provide 1 h of tracer-concentration distribution data within tissue. Early time points (19 min) were used to construct 3D K(trans) and porosity maps using a two-compartment model; tracer transport was predicted at later time points using a 3D porous media model. Model development involved selecting an arterial input function (AIF) and conducting a sensitivity analysis of model parameters (tissue, vascular, and initial estimation of solute concentration in plasma) to investigate the effects on transport for a specific tumor. The developed model was then used to predict transport in two additional tumors. The sensitivity analysis suggests that plasma fluid transport is more sensitive to parameter changes than solute transport due to the dominance of transvascular exchange. Gd-DTPA distribution was similar to experimental patterns, but differences in Gd-DTPA magnitude at later time points may result from inaccurate selection of AIF. Thus, accurate AIF estimation is important for later time point prediction of low molecular weight tracer or drug transport in smaller tumors.

Engineering the Lymphatic System

The recent advances in our understanding of lymphatic physiology and the role of the lymphatics in actively regulating fluid balance, lipid transport, and immune cell trafficking has been furthered in part through innovations in imaging, tissue engineering, quantitative biology, biomechanics, and computational modeling. Interdisciplinary and bioengineering approaches will continue to be crucial to the progression of the field, given that lymphatic biology and function are intimately woven with the local microenvironment and mechanical loads experienced by the vessel. This is particularly the case in lymphatic diseases such as lymphedema where the microenvironment can be drastically altered by tissue fibrosis and adipocyte accumulation. In this review we will highlight contributions engineering and mechanics have made to lymphatic physiology and will discuss areas that will be important for future research.

The physics of cancer: the role of physical interactions and mechanical forces in metastasis

Metastasis is a complex, multistep process responsible for >90% of cancer-related deaths. In addition to genetic and external environmental factors, the physical interactions of cancer cells with their microenvironment, as well as their modulation by mechanical forces, are key determinants of the metastatic process. We reconstruct the metastatic process and describe the importance of key physical and mechanical processes at each step of the cascade. The emerging insight into these physical interactions may help to solve some long-standing questions in disease progression and may lead to new approaches to developing cancer diagnostics and therapies.

Interstitial flow influences direction of tumor cell migration through competing mechanisms

Interstitial flow is the convective transport of fluid through tissue extracellular matrix. This creeping fluid flow has been shown to affect the morphology and migration of cells such as fibroblasts, cancer cells, endothelial cells, and mesenchymal stem cells. A microfluidic cell culture system was designed to apply stable pressure gradients and fluid flow and allow direct visualization of transient responses of cells seeded in a 3D collagen type I scaffold. We used this system to examine the effects of interstitial flow on cancer cell morphology and migration and to extend previous studies showing that interstitial flow increases the metastatic potential of MDA-MB-435S melanoma cells [Shields J, et al. (2007) Cancer Cell 11:526-538]. Using a breast carcinoma line (MDA-MB-231) we also observed cell migration along streamlines in the presence of flow; however, we further demonstrated that the strength of the flow as well as the cell density determined directional bias of migration along the streamline. In particular, we found that cells either at high seeding density or with the CCR-7 receptor inhibited migration against, rather than with the flow. We provide further evidence that CCR7-dependent autologous chemotaxis is the mechanism that leads to migration with the flow, but also demonstrate a competing CCR7-independent mechanism that causes migration against the flow. Data from experiments investigating the effects of cell concentration, interstitial flow rate, receptor activity, and focal adhesion kinase phosphorylation support our hypothesis that the competing stimulus is integrin mediated. This mechanism may play an important role in development of metastatic disease.

Responses of endothelial cells to extremely slow flows

The process of blood vessel formation is accompanied by very minimal flow in the beginning, followed by increased flow rates once the vessel develops sufficiently. Many studies have been performed for endothelial cells at shear stress levels of 0.1-60 dyn∕cm(2); however, little is known about the effect of extremely slow flows (shear stress levels of 10(-4)-10(-2) dyn∕cm(2)) that endothelial cells may experience during early blood vessel formation where flow-sensing by indirect mass transport sensing rather than through mechanoreceptor sensing mechanisms would become more important. Here, we show that extremely low flows enhance proliferation, adherens junction protein localization, and nitric oxide secretion of endothelial cells, but do not induce actin filament reorganization. The responses of endothelial cells in different flow microenvironments need more attention because increasing evidence shows that endothelial cell behaviors at the extremely slow flow regimes cannot be linearly extrapolated from observations at faster flow rates. The devices and methods described here provide a useful platform for such studies.

Transport and shear in a microfluidic membrane bilayer device for cell culture

Microfluidic devices have been established as useful platforms for cell culture for a broad range of applications, but challenges associated with controlling gradients of oxygen and other soluble factors and hemodynamic shear forces in small, confined channels have emerged. For instance, simple microfluidic constructs comprising a single cell culture compartment in a dynamic flow condition must handle tradeoffs between sustaining oxygen delivery and limiting hemodynamic shear forces imparted to the cells. These tradeoffs present significant difficulties in the culture of mesenchymal stem cells (MSCs), where shear is known to regulate signaling, proliferation, and expression. Several approaches designed to shield cells in microfluidic devices from excessive shear while maintaining sufficient oxygen concentrations and transport have been reported. Here we present the relationship between oxygen transport and shear in a "membrane bilayer" microfluidic device, in which soluble factors are delivered to a cell population by means of flow through a proximate channel separated from the culture channel by a membrane. We present an analytical model that describes the characteristics of this device and its ability to independently modulate oxygen delivery and hemodynamic shear imparted to the cultured cells. This bilayer configuration provides a more uniform oxygen concentration profile that is possible in a single-channel system, and it enables independent tuning of oxygen transport and shear parameters to meet requirements for MSCs and other cells known to be sensitive to hemodynamic shear stresses.

Supply of nutrients to cells in engineered tissues

A proper supply of nutrients to cells in engineered tissues is paramount for an optimal development and survival of these tissues. However, especially in tissues with clinically relevant sizes, the mass transport of nutrients into the tissue is often insufficient to sustain all the cells within the tissue. This is not only the case during in vitro culture. After implantation of an engineered tissue, a vascular network is not directly established. Therefore, the mass transport of nutrients is also critical during the initial period after implantation. This review introduces the basics of mass transport, leading to the conclusion that three main concepts can be used to increase nutrient supply in tissue engineering. These are; increasing the overall diffusion coefficient, decreasing the diffusion distance, or increasing convective transport. Based on these concepts, the main strategies that have been developed to enhance the supply of nutrients to cells in engineered tissues will be discussed.

An arthroscopic device to assess articular cartilage defects and treatment with a hydrogel

The hydraulic resistance R across osteochondral tissue, especially articular cartilage, decreases with degeneration and erosion. Clinically useful measures to quantify and diagnose the extent of cartilage degeneration and efficacy of repair strategies, especially with regard to pressure maintenance, are still developing. The hypothesis of this study was that hydraulic resistance provides a quantitative measure of osteochondral tissue that could be used to evaluate the state of cartilage damage and repair. The aims were to (1) develop a device to measure R in an arthroscopic setting, (2) determine whether the device could detect differences in R for cartilage, an osteochondral defect, and cartilage treated using a hydrogel ex vivo, and (3) determine how quickly such differences could be discerned. The apparent hydraulic resistance of defect samples was ~35% less than intact cartilage controls, while the resistance of hydrogel-filled groups was not statistically different than controls, suggesting some restoration of fluid pressurization in the defect region by the hydrogel. Differences in hydraulic resistance between control and defect groups were apparent after 4 s. The results indicate that the measurement of R is feasible for rapid and quantitative functional assessment of the extent of osteochondral defects and repair. The arthroscopic compatibility of the device demonstrates the potential for this measurement to be made in a clinical setting.

Fluid dynamics analysis of a novel micropatterned cell bioreactor

Although flow-based bioreactor has been widely used to provide sufficient mass transportation and nutrient supply for cell proliferation, differentiation, and apoptosis, the underlying mechanism of cell responses to applied flow at single cell level remains unclear. This study has developed a novel bioreactor that combines flow bioreactor with microfabrication technique to isolate individual cells onto micropatterned substrate. A mechanical model has also been developed to quantify the flow field or the microenvironment around the single cell; flow dynamics has been analyzed on five geometrically different patterns of circle-, cube-, 1:2 ellipse-, 1:3 ellipse-, and rectangle-shaped "virtual cells." The results of this study have demonstrated that the flow field is highly pattern dependent, and all the hydrodynamic development length, cell spacing, and orientation of inlet velocity vector are crucial for maintaining a fully developed flow. This study has provided a theoretical basis for optimizing the design of micropatterned flow bioreactor and a novel approach to understand the cell mechanotransduction and cell-surface interaction at single cell level.

Heparan sulfate proteoglycans mediate interstitial flow mechanotransduction regulating MMP-13 expression and cell motility via FAK-ERK in 3D collagen

Background

Interstitial flow directly affects cells that reside in tissues and regulates tissue physiology and pathology by modulating important cellular processes including proliferation, differentiation, and migration. However, the structures that cells utilize to sense interstitial flow in a 3-dimensional (3D) environment have not yet been elucidated. Previously, we have shown that interstitial flow upregulates matrix metalloproteinase (MMP) expression in rat vascular smooth muscle cells (SMCs) and fibroblasts/myofibroblasts via activation of an ERK1/2-c-Jun pathway, which in turn promotes cell migration in collagen. Herein, we focused on uncovering the flow-induced mechanotransduction mechanism in 3D.

Methodology/Principal Findings

Cleavage of rat vascular SMC surface glycocalyx heparan sulfate (HS) chains from proteoglycan (PG) core proteins by heparinase or disruption of HS biosynthesis by silencing N-deacetylase/N-sulfotransferase 1 (NDST1) suppressed interstitial flow-induced ERK1/2 activation, interstitial collagenase (MMP-13) expression, and SMC motility in 3D collagen. Inhibition or knockdown of focal adhesion kinase (FAK) also attenuated or blocked flow-induced ERK1/2 activation, MMP-13 expression, and cell motility. Interstitial flow induced FAK phosphorylation at Tyr925, and this activation was blocked when heparan sulfate proteoglycans (HSPGs) were disrupted. These data suggest that HSPGs mediate interstitial flow-induced mechanotransduction through FAK-ERK. In addition, we show that integrins are crucial for mechanotransduction through HSPGs as they mediate cell spreading and maintain cytoskeletal rigidity.

Conclusions/Significance

We propose a conceptual mechanotransduction model wherein cell surface glycocalyx HSPGs, in the presence of integrin-mediated cell-matrix adhesions and cytoskeleton organization, sense interstitial flow and activate the FAK-ERK signaling axis, leading to upregulation of MMP expression and cell motility in 3D. This is the first study to describe a flow-induced mechanotransduction mechanism via HSPG-mediated FAK activation in 3D. This study will be of interest in understanding the flow-related mechanobiology in vascular lesion formation, tissue morphogenesis, cancer cell metastasis, and stem cell differentiation in 3D, and also has implications in tissue engineering.

Forcing form and function: biomechanical regulation of tumor evolution

Cancer cells exist in a constantly evolving tissue microenvironment of diverse cell types within a proteinaceous extracellular matrix. As tumors evolve, the physical forces within this complex microenvironment change, with pleiotropic effects on both cell- and tissue-level behaviors. Recent work suggests that these biomechanical factors direct tissue development and modulate tissue homeostasis, and, when altered, crucially influence tumor evolution. In this review, we discuss the biomechanical regulation of cell and tissue homeostasis from the molecular, cellular and tissue levels, including how modifications of this physical dialogue could contribute to cancer etiology. Because of the broad impact of biomechanical factors on cell and tissue functions, an understanding of tumor evolution from the biomechanical perspective should improve risk assessment, clinical diagnosis and the efficacy of cancer treatment.

PAM2 (piston assisted microsyringe): a new rapid prototyping technique for biofabrication of cell incorporated scaffolds

Rapid prototyping techniques are widely used to fabricate well-defined three-dimensional structures of tissue homologs. The piston-assisted microsyringe (PAM2) is a rapid prototyping technology specifically developed for low-shear stress extrusion of viscous hydrogel solutions containing cells. In this article the working parameters of the system were established to guarantee the realization of spatially controlled hydrogel scaffolds. Moreover the shear stresses acting on the cell membrane during extrusion was investigated through a computational fluid-dynamic analysis. The computational models show that the shear stress on the cells is of the order of 100 Pa during the extrusion process. HepG2 cells encapsulated in alginate were then extruded into spatially organized hepatic lobule-like architectures and their viability and function were evaluated. The results show that the metabolic fingerprint of the cells is preserved with respect to controls and the cells are uniformly distributed through the gel scaffold.

Computational modeling of fluid flow and intra-ocular pressure following glaucoma surgery

Background

Glaucoma surgery is the most effective means for lowering intraocular pressure by providing a new route for fluid to exit the eye. This new pathway is through the sclera of the eye into sub-conjunctival tissue, where a fluid filled bleb typically forms under the conjunctiva. The long-term success of the procedure relies on the capacity of the sub-conjunctival tissue to absorb the excess fluid presented to it, without generating excessive scar tissue during tissue remodeling that will shut-down fluid flow. The role of inflammatory factors that promote scarring are well researched yet little is known regarding the impact of physical forces on the healing response.

Methodology

To help elucidate the interplay of physical factors controlling the distribution and absorption of aqueous humor in sub-conjunctival tissue, and tissue remodeling, we have developed a computational model of fluid production in the eye and removal via the trabecular/uveoscleral pathways and the surgical pathway. This surgical pathway is then linked to a porous media computational model of a fluid bleb positioned within the sub-conjunctival tissue. The computational analysis is centered on typical functioning bleb geometry found in a human eye following glaucoma surgery. A parametric study is conducted of changes in fluid absorption by the sub-conjunctival blood vessels, changes in hydraulic conductivity due to scarring, and changes in bleb size and shape, and eye outflow facility.

Conclusions

This study is motivated by the fact that some blebs are known to have ‘successful’ characteristics that are generally described by clinicians as being low, diffuse and large without the formation of a distinct sub-conjunctival encapsulation. The model predictions are shown to accord with clinical observations in a number of key ways, specifically the variation of intra-ocular pressure with bleb size and shape and the correspondence between sites of predicted maximum interstitial fluid pressure and key features observed in blebs, which gives validity to the model described here. This model should contribute to a more complete explanation of the physical processes behind successful bleb characteristics and provide a new basis for clinically grading blebs.

Interaction between the extracellular matrix and lymphatics: consequences for lymphangiogenesis and lymphatic function

The lymphatic system is important for body fluid balance as well as immunological surveillance. Due to the identification of new molecular markers during the last decade, there has been a recent dramatic increase in our knowledge on the molecular mechanisms involved in lymphatic vessel growth (lymphangiogenesis) and lymphatic function. Here we review data showing that although it is often overlooked, the extracellular matrix plays an important role in the generation of new lymphatic vessels as a response to physiological and pathological stimuli. Extracellular matrix-lymphatic interactions as well as biophysical characteristics of the stroma have consequences for tumor formation, growth and metastasis. During the recent years, anti-lymphangiogenesis has emerged as an additional therapeutic modality to the clinically applied anti-angiogenesis strategy. Oppositely, enhancement of lymphangiogenesis in situations of lymph accumulation is seen as a promising strategy to a set of conditions where few therapeutic avenues are available. Knowledge on the interaction between the extracellular matrix and the lymphatics may enhance our understanding of the underlying mechanisms and may ultimately lead to better therapies for conditions where reduced or increased lymphatic function is the therapeutic target.

Reduced hydraulic permeability of three-dimensional collagen scaffolds attenuates gel contraction and promotes the growth and differentiation of mesenchymal stem cells

Optimal scaffold characteristics are essential for the therapeutic application of engineered tissues. Hydraulic permeability (k) affects many properties of collagen gels, such as mechanical properties, cell-scaffold interactions within three dimensions (3D), oxygen flow and nutrient diffusion. However, the cellular response to 3D gel scaffolds of defined k values has not been investigated. In this study, unconfined plastic compression under increasing load was used to produce collagen gels with increasing solid volume fractions. The Happel model was used to calculate the resulting permeability values in order to study the interaction of k with gel mechanical properties and mesenchymal stem cell (MSC)-induced gel contraction, metabolism and differentiation in both non-osteogenic (basal medium) and osteogenic medium for up to 3 weeks. Collagen gels of fibrillar densities ranging from 0.3 to >4.1 wt.% gave corresponding k values that ranged from 1.00 to 0.03 microm(2). Mechanical testing under compression showed that the collagen scaffold modulus increased with collagen fibrillar density and a decrease in k value. MSC-induced gel contraction decreased as a direct function of decreasing k value. Relative to osteogenic conditions, non-osteogenic MSC cultures exhibited a more than 2-fold increase in gel contraction. MSC metabolic activity increased similarly under both osteogenic and non-osteogenic culture conditions for all levels of plastic compression. Under osteogenic conditions MSC differentiation and mineralization, as indicated by alkaline phosphatase activity and von Kossa staining, respectively, increased in response to an elevation in collagen fibrillar density and decreased gel permeability. In this study, gel scaffolds with higher collagen fibrillar densities and corresponding lower k values provided a greater potential for MSC differentiation and appear most promising for bone grafting purposes. Thus, cell-scaffold interactions can be optimized by defining the 3D properties of collagen scaffolds through k adjustment.

Effect of sulfated glycosaminoglycan digestion on the transverse permeability of medial collateral ligament

Dermatan and chondroitin sulfate glycosaminoglycans (GAGs) comprise over 90% of the GAG content in ligament. Studies of their mechanical contribution to soft tissues have reported conflicting results. Measuring the transient compressive response and biphasic material parameters of the tissue may elucidate the contributions of GAGs to the viscoelastic response to deformation. The hypotheses of the current study were that digestion of sulfated GAGs would decrease compressive stress and aggregate modulus while increasing the permeability of porcine medial collateral ligament (MCL). Confined compression stress relaxation experiments were carried out on porcine MCL and tissue treated with chondroitinase ABC (ChABC). Results were fit to a biphasic constitutive model to derive permeability and aggregate modulus. Bovine articular cartilage was used as a benchmark tissue to verify that the apparatus provided reliable results. GAG digestion removed up to 88% of sulfated GAGs from the ligament. Removal of sulfated GAGs increased the permeability of porcine MCL nearly 6-fold versus control tissues. Peak stress decreased significantly. Bovine articular cartilage exhibited the typical reduction of GAG content and resultant decreases in stress and modulus and increases in permeability with ChABC digestion. Given the relatively small amount of GAG in ligament (<1% of tissue dry weight) and the significant change in peak stress and permeability upon removal of GAGs, sulfated GAGs may play a significant role in maintaining the apposition of collagen fibrils in the transverse direction, thus supporting dynamic compressive loads experienced by the ligament during complex joint motion.

Shear stress modulation of smooth muscle cell marker genes in 2-D and 3-D depends on mechanotransduction by heparan sulfate proteoglycans and ERK1/2

Background

During vascular injury, vascular smooth muscle cells (SMCs) and fibroblasts/myofibroblasts (FBs/MFBs) are exposed to altered luminal blood flow or transmural interstitial flow. We investigate the effects of these two types of fluid flows on the phenotypes of SMCs and MFBs and the underlying mechanotransduction mechanisms.

Methodology/Principal Findings

Exposure to 8 dyn/cm² laminar flow shear stress (2-dimensional, 2-D) for 15 h significantly reduced expression of α-smooth muscle actin (α-SMA), smooth muscle protein 22 (SM22), SM myosin heavy chain (SM-MHC), smoothelin, and calponin. Cells suspended in collagen gels were exposed to interstitial flow (1 cmH₂O, ∼0.05 dyn/cm², 3-D), and after 6 h of exposure, expression of SM-MHC, smoothelin, and calponin were significantly reduced, while expression of α-SMA and SM22 were markedly enhanced. PD98059 (an ERK1/2 inhibitor) and heparinase III (an enzyme to cleave heparan sulfate) significantly blocked the effects of laminar flow on gene expression, and also reversed the effects of interstitial flow on SM-MHC, smoothelin, and calponin, but enhanced interstitial flow-induced expression of α-SMA and SM22. SMCs and MFBs have similar responses to fluid flow. Silencing ERK1/2 completely blocked the effects of both laminar flow and interstitial flow on SMC marker gene expression. Western blotting showed that both types of flows induced ERK1/2 activation that was inhibited by disruption of heparan sulfate proteoglycans (HSPGs).

Conclusions/Significance

The results suggest that HSPG-mediated ERK1/2 activation is an important mechanotransduction pathway modulating SMC marker gene expression when SMCs and MFBs are exposed to flow. Fluid flow may be involved in vascular remodeling and lesion formation by affecting phenotypes of vascular wall cells. This study has implications in understanding the flow-related mechanobiology in vascular lesion formation, tumor cell invasion, and stem cell differentiation.

Effect of mechanical factors on the function of engineered human blood microvessels in microfluidic collagen gels

This work examines how mechanical signals affect the barrier function and stability of engineered human microvessels in microfluidic type I collagen gels. Constructs that were exposed to chronic low flow displayed high permeabilities to bovine serum albumin and 10 kDa dextran, numerous focal leaks, low size selectivity, and short lifespan of less than one week. Higher flows promoted barrier function and increased longevity; at the highest flows, the barrier function rivaled that observed in vivo, and all vessels survived to day 14. By studying the physiology of microvessels of different geometries, we established that shear stress and transmural pressure were the dominant mechanical signals that regulated barrier function and vascular stability, respectively. In microvessels that were exposed to high flow, elevation of intracellular cyclic AMP further increased the selectivity of the barrier and strongly suppressed cell proliferation. Computational models that incorporated stress dependence successfully predicted vascular phenotype. Our results indicate that the mechanical microenvironment plays a major role in the functionality and stability of engineered human microvessels in microfluidic collagen gels.

Microfluidic platforms for studies of angiogenesis, cell migration, and cell-cell interactions. Sixth International Bio-Fluid Mechanics Symposium and Workshop March 28-30, 2008 Pasadena, California

Recent advances in microfluidic technologies have opened the door for creating more realistic in vitro cell culture methods that replicate many aspects of the true in vivo microenvironment. These new designs (i) provide enormous flexibility in controlling the critical biochemical and biomechanical factors that influence cell behavior, (ii) allow for the introduction of multiple cell types in a single system, (iii) provide for the establishment of biochemical gradients in two- or three-dimensional geometries, and (iv) allow for high quality, time-lapse imaging. Here, some of the recent developments are reviewed, with a focus on studies from our own laboratory in three separate areas: angiogenesis, cell migration in the context of tumor cell-endothelial interactions, and liver tissue engineering.

A low shear stress modular bioreactor for connected cell culture under high flow rates

A generic "system on a plate" modular multicompartmental bioreactor array which enables microwell protocols to be transferred directly to the bioreactor modules, without redesign of cell culture experiments or protocols is described. The modular bioreactors are simple to assemble and use and can be easily compared with standard controls since cell numbers and medium volumes are quite similar. Starting from fluid dynamic and mass transport considerations, a modular bioreactor chamber was first modeled and then fabricated using "milli-molding," a technique adapted from soft lithography. After confirming that the shear stress was extremely low in the system in the range of useful flow rates, the bioreactor chambers were tested using hepatocytes. The results show that the bioreactor chambers can increase or maintain cell viability and function when the flow rates are below 500 microL/min, corresponding to wall shear stresses of 10(-5) Pa or less at the cell culture surface.

A multichamber fluidic device for 3D cultures under interstitial flow with live imaging: development, characterization, and applications

Interstitial flow is an important biophysical cue that can affect capillary morphogenesis, tumor cell migration, and fibroblast remodeling of the extracellular matrix, among others. Current models that incorporate interstitial flow and that are suitable for live imaging lack the ability to perform multiple simultaneous experiments, for example, to compare effects of growth factors, extracellular matrix composition, etc. We present a nine-chamber radial flow device that allows simultaneous 3D fluidic experiments for relatively long-term culture with live imaging capabilities. Flow velocity profiles were characterized by fluorescence recovery after photobleaching (FRAP) for flow uniformity and estimating the hydraulic conductivity. We demonstrate lymphatic and blood capillary morphogenesis in fibrin gels over 10 days, comparing flow with static conditions as well as the effects of an engineered variant of VEGF that binds fibrin via Factor XIII. We also demonstrate the culture of contractile fibroblasts and co-cultures with tumor cells for modeling the tumor microenvironment. Therefore, this device is useful for studies of capillary morphogenesis, cell migration, contractile cells like fibroblasts, and multicellular cultures, all under interstitial flow.

Diffusion of water in skeletal muscle tissue is not influenced by compression in a rat model of deep tissue injury

Sustained mechanical loading of skeletal muscle may result in the development of a severe type of pressure ulcer, referred to as deep tissue injury. Recently it was shown that the diffusion of large molecules (10-150kDa) is impaired during deformation of tissue-engineered skeletal muscle, suggesting a role for impaired diffusion in the aetiology of deep tissue injury. However, the influence of deformation on diffusion of smaller molecules on its aetiology is less clear. This motivated the present study designed to investigate the influence of deformation of skeletal muscle on the diffusion of water, which can be measured with diffusion tensor magnetic resonance imaging (MRI). It could be predicted that this approach will provide valuable information on the diffusion of small molecules. Additionally the relationship between muscle temperature and diffusion was investigated. During deformation of the tibialis anterior a decrease of the apparent diffusion coefficient (ADC) was observed (7.2+/-3.9%). The use of a finite element model showed that no correlation existed between the maximum shear strain and the decrease of the ADC. The ADC in the uncompressed gastrocnemius muscle decreased with 5.9+/-3.7%. In an additional experiment a clear correlation was obtained between the decrease of the ADC and the relative temperature change of skeletal muscle tissue as measured by MRI. Taken together, it was concluded that (1) the decreased diffusion of water was not a direct effect of tissue deformation and (2) that it is likely that the observed decreased ADC during deformation was a result of a decreased muscle temperature. The present study therefore provides evidence that diffusion of small molecules, particularly oxygen and carbon dioxide, is not impaired during deformation of skeletal muscle tissue.

Role of in vitro release models in formulation development and quality control of parenteral depots

This review article provides an assessment of advantages/limitations of the use of current in vitro release models to predict in vivo performance of parenteral sustained release products (injectable depots). As highlighted, key characteristics influencing the in vivo drug fate may vary with the route of administration and the type of sustained release formulation. To this end, an account is given on three representative injection sites (intramuscular, subcutaneous and intra-articular) as well as on in vitro release mechanism(s) of drugs from five commonly investigated depot principles (suspensions, microspheres, hydrogels, lipophilic solutions, and liposomes/other nano-size formulations). Current in vitro release models are, to a different extent, able to mimic the rate, transport and equilibrium processes that the drug substance may experience in the environment of the administration site. Their utility for the purpose of quality control including in vitro-in vivo correlations and formulation design is discussed.

Dermal collagen and lipid deposition correlate with tissue swelling and hydraulic conductivity in murine primary lymphedema

Primary lymphedema is a congenital pathology of dysfunctional lymphatic drainage characterized by swelling of the limbs, thickening of the dermis, and fluid and lipid accumulation in the underlying tissue. Two mouse models of primary lymphedema, the Chy mouse and the K14-VEGFR-3-Ig mouse, both lack dermal lymphatic capillaries and exhibit a lymphedematous phenotype attributable to disrupted VEGFR-3 signaling. Here we show that the differences in edematous tissue composition between these two models correlated with drastic differences in hydraulic conductivity. The skin of Chy mice possessed significantly higher levels of collagen and fat, whereas K14-VEGFR-3-Ig mouse skin composition was relatively normal, as compared with their respective wild-type controls. Functionally, this resulted in a greatly increased dermal hydraulic conductivity in K14-VEGFR3-Ig, but not Chy, mice. Our data suggest that lymphedema associated with increased collagen and lipid accumulation counteracts an increased hydraulic conductivity associated with dermal swelling, which in turn further limits interstitial transport and swelling. Without lipid and collagen accumulation, hydraulic conductivity is increased and overall swelling is minimized. These opposing tissue responses to primary lymphedema imply that tissue remodeling--predominantly collagen and fat deposition--may dictate tissue swelling and govern interstitial transport in lymphedema.

A microperfused incubator for tissue mimetic 3D cultures

High density, three-dimensional (3D) cultures present physical similarities to in vivo tissue and are invaluable tools for pre-clinical therapeutic discoveries and development of tissue engineered constructs. Unfortunately, the use of dense cultures is hindered by intra-culture transport limits allowing just a few layer thick cultures for reproducible studies. In order to overcome diffusion limits in intra-culture nutrient and gas availability, a simple scalable microfluidic perfusion platform was developed and validated. A novel perfusion approach maintained laminar flow of nutrients through the culture to meet metabolic need, while removing depleted medium and catabolites. Velocity distributions and 3D flow patterns were measured using microscopic particle image velocimetry. The effectiveness of forced convection laminar perfusion was confirmed by culturing 700 microm thick neural-astrocytic (1:1) constructs at cell density approaching that of the brain (50,000 cells/mm(3)). At the optimized flow rate of the nutrient medium, the culture viability reached 90% through the full construct thickness at 2 days of perfusion while unperfused controls exhibited widespread cell death. The membrane aerated perfusion platform was integrated within a miniature, imaging accessible enclosure enabling temperature and gas control of the culture environment. Temperature measurements demonstrated fast feedback response to environmental changes resulting in the maintenance of the physiological temperature within 37 +/- 0.2 degrees C. Reproducible culturing of tissue equivalents within dynamically controlled environments will provide higher fidelity to in vivo function in an in vitro accessible format for cell-based assays and regenerative medicine.

Navigating ECM barriers at the invasive front: the cancer cell-stroma interface

A seminal event in cancer progression is the ability of the neoplastic cell to mobilize the necessary machinery to breach surrounding extracellular matrix barriers while orchestrating a host stromal response that ultimately supports tissue-invasive and metastatic processes. With over 500 proteolytic enzymes identified in the human genome, interconnecting webs of protease-dependent and protease-independent processes have been postulated to drive the cancer cell invasion program via schemes of daunting complexity. Increasingly, however, a body of evidence has begun to emerge that supports a unifying model wherein a small group of membrane-tethered enzymes, termed the membrane-type matrix metalloproteinases (MT-MMPs), plays a dominant role in regulating cancer cell, as well as stromal cell, traffic through the extracellular matrix barriers assembled by host tissues in vivo. Understanding the mechanisms that underlie the regulation and function of these metalloenzymes as host cell populations traverse the dynamic extracellular matrix assembled during neoplastic states should provide new and testable theories regarding cancer invasion and metastasis.

Interstitial flow induces MMP-1 expression and vascular SMC migration in collagen I gels via an ERK1/2-dependent and c-Jun-mediated mechanism

The migration of vascular smooth muscle cells (SMCs) and fibroblasts into the intima after vascular injury is a central process in vascular lesion formation. The elevation of transmural interstitial flow is also observed after damage to the vascular endothelium. We have previously shown that interstitial flow upregulates matrix metalloproteinase-1 (MMP-1) expression, which in turn promotes SMC and fibroblast migration in collagen I gels. In this study, we investigated further the mechanism of flow-induced MMP-1 expression. An ERK1/2 inhibitor PD-98059 completely abolished interstitial flow-induced SMC migration and MMP-1 expression. Interstitial flow promoted ERK1/2 phosphorylation, whereas PD-98059 abolished flow-induced activation. Silencing ERK1/2 completely abolished MMP-1 expression and SMC migration. In addition, interstitial flow increased the expression of activator protein-1 transcription factors (c-Jun and c-Fos), whereas PD-98059 attenuated flow-induced expression. Knocking down c-jun completely abolished flow-induced MMP-1 expression, whereas silencing c-fos did not affect MMP-1 expression. Taken together, our data indicate that interstitial flow induces MMP-1 expression and SMC migration in collagen I gels via an ERK1/2-dependent and c-Jun-mediated mechanism and suggest that interstitial flow, ERK1/2 MAPK, c-Jun, and MMP-1 may play important roles in SMC migration and neointima formation after vascular injury.

Computational design of drainage systems for vascularized scaffolds

This computational study analyzes how to design a drainage system for porous scaffolds so that the scaffolds can be vascularized and perfused without collapse of the vessel lumens. We postulate that vascular transmural pressure--the difference between lumenal and interstitial pressures--must exceed a threshold value to avoid collapse. Model geometries consisted of hexagonal arrays of open channels in an isotropic scaffold, in which a small subset of channels was selected for drainage. Fluid flow through the vessels and drainage channel, across the vascular wall, and through the scaffold were governed by Navier-Stokes equations, Starling's Law of Filtration, and Darcy's Law, respectively. We found that each drainage channel could maintain a threshold transmural pressure only in nearby vessels, with a radius-of-action dependent on vascular geometry and the hydraulic properties of the vascular wall and scaffold. We illustrate how these results can be applied to microvascular tissue engineering, and suggest that scaffolds be designed with both perfusion and drainage in mind.

Cell Guidance by 3D-Gradients in Hydrogel Matrices: Importance for Biomedical Applications

Concentration gradients of soluble and matrix-bound guidance cues in the extracellular matrix direct cell growth in native tissues and are of great interest for design of biomedical scaffolds and on implant surfaces. The focus of this review is to demonstrate the importance of gradient guidance for cells as it would be desirable to direct cell growth onto/into biomedical devices. Many studies have been described that illustrate the production and characterization of surface gradients, but three dimensional (3D)-gradients that direct cellular behavior are not well investigated. Hydrogels are considered as synthetic replacements for native extracellular matrices as they share key functions such as 2D- or 3D-solid support, fibrous structure, gas- and nutrition permeability and allow storage and release of biologically active molecules. Therefore this review focuses on current studies that try to implement soluble or covalently-attached gradients of growth factors, cytokines or adhesion sequences into 3D-hydrogel matrices in order to control cell growth, orientation and migration towards a target. Such gradient architectures are especially desirable for wound healing purposes, where defined cell populations need to be recruited from the blood stream and out of the adjacent tissue, in critical bone defects, for vascular implants or neuronal guidance structures where defined cell populations should be guided by appropriate signals to reach their proper positions or target tissues in order to accomplish functional repair.

Simultaneous generation of chemical concentration and mechanical shear stress gradients using microfluidic osmotic flow comparable to interstitial flow

Cells are very sensitive to various microenvironmental cues, including mechanical stress and chemical gradients. Therefore, physiologically relevant models of cells should consider how cells sense and respond to microenvironmental cues. This can be accomplished by using microfluidic systems, in which fluid physics can be realized at a nanoliter scale. Here we describe a simple and versatile method to study the generation of chemical concentration and mechanical shear stress gradients in a single microfluidic chip. Our system uses an osmotic pump that produces very slow (<a few microm/s) and controlled flow, allowing a wide and stable diffusion of specific chemical concentration. We also established a shear stress gradient passively via a circular channel in the interstitial level. For evaluation of the system, we used L929 mouse fibroblast cells and simultaneously exposed them to a mechanical stress gradient and a chemical nutrient gradient. The interstitial shear stress level clearly affected cell alignment, mobility velocity, and attachment. At the same time, cell proliferation reflected nutrient concentration level. Our system, which enables continuous and long-term culture of cells in a combined chemical and mechanical gradient, provides physiologically realistic conditions and will be applicable to studies of cancer metastasis and stem cell differentiation.

Dynamics of different-sized solid-state nanocrystals as tracers for a drug-delivery system in the interstitium of a human tumor xenograft

INTRODUCTION

Recent anticancer drugs have been made larger to pass selectively through tumor vessels and stay in the interstitium. Understanding drug movement in association with its size at the single-molecule level and estimating the time needed to reach the targeted organ is indispensable for optimizing drug delivery because single cell-targeted therapy is the ongoing paradigm. This report describes the tracking of single solid nanoparticles in tumor xenografts and the estimation of arrival time.

METHODS

Different-sized nanoparticles measuring 20, 40, and 100 nm were injected into the tail vein of the female Balb/c nu/nu mice bearing human breast cancer on their backs. The movements of the nanoparticles were visualized through the dorsal skin-fold chamber with the high-speed confocal microscopy that we manufactured.

RESULTS

An analysis of the particle trajectories revealed diffusion to be inversely related to the particle size and position in the tumor, whereas the velocity of the directed movement was related to the position. The difference in the velocity was the greatest for 40-nm particles in the perivascular to the intercellular region: difference = 5.8 nm/s. The arrival time of individual nanoparticles at tumor cells was simulated. The estimated times for the 20-, 40-, and 100-nm particles to reach the tumor cells were 158.0, 218.5, and 389.4 minutes, respectively, after extravasation.

CONCLUSIONS

This result suggests that the particle size can be individually designed for each goal. These data and methods are also important for understanding drug pharmacokinetics. Although this method may be subject to interference by surface molecules attached on the particles, it has the potential to elucidate the pharmacokinetics involved in constructing novel drug-delivery systems involving cell-targeted therapy.

Interstitial flow promotes vascular fibroblast, myofibroblast, and smooth muscle cell motility in 3-D collagen I via upregulation of MMP-1

Neointima formation often occurs in regions where the endothelium has been damaged and the transmural interstitial flow is elevated. Vascular smooth muscle cells (SMCs) and fibroblasts/myofibroblasts (FBs/MFBs) contribute to intimal thickening by migrating from the media and adventitia into the site of injury. In this study, for the first time, the direct effects of interstitial flow on SMC and FB/MFB migration were investigated in an in vitro three-dimensional system. Collagen I gels were used to mimic three-dimensional extracellular matrix (ECM) for rat aortic SMCs and FBs/MFBs. Exposure to interstitial flow induced by 1 cmH(2)O pressure differential (shear stress, approximately 0.05 dyn/cm(2); flow velocity, approximately 0.5 microm/s; and Darcy permeability, approximately 10(-11) cm(2)) substantially enhanced cell motility. Matrix metalloproteinase (MMP) inhibitor (GM-6001) abolished flow-induced migration augmentation, which suggested that the enhanced motility was MMP dependent. The upregulation of MMP-1 played a critical role for the flow-enhanced motility, which was further confirmed by silencing MMP-1 gene expression. Longer exposures to higher flows suppressed the number of migrated cells, although MMP-1 gene expression remained high. This suppression was a result of both flow-induced tissue inhibitor of metalloproteinase-1 upregulation and increased apoptotic and necrotic cell death. Interstitial flow did not affect MMP-2 gene expression or activity in the collagen I gel for any cell type. Our findings shed light on the mechanism by which vascular SMCs and FBs/MFBs contribute to intimal thickening in regions of vascular injury where interstitial flow is elevated.

3D collagen cultures under well-defined dynamic strain: a novel strain device with a porous elastomeric support

The field of mechanobiology has grown tremendously in the past few decades, and it is now well accepted that dynamic stresses and strains can impact cell and tissue organization, cell-cell and cell-matrix communication, matrix remodeling, cell proliferation and apoptosis, cell migration, and many other cell behaviors in both physiological and pathophysiological situations. Natural reconstituted matrices like collagen and fibrin are often used for three-dimensional (3D) mechanobiology studies because they naturally form fibrous architectures and are rich in cell adhesion sites; however, they are physically weak and typically contain >99% water, making it difficult to apply dynamic stresses to them in a truly 3D context. Here we present a composite matrix and strain device that can support natural matrices within a macroporous elastic structure of polyurethane. We characterize this system both in terms of its mechanical behavior and its ability to support the growth and in vivo-like behaviors of primary human lung fibroblasts cultured in collagen. The porous polyurethane was created with highly interconnected pores in the hundreds of microm size scale, so that while it did not affect cell behavior in the collagen gel within the pores, it could control the overall elastic behavior of the entire tissue culture system. In this way, a well-defined dynamic strain could be imposed on the 3D collagen and cells within the collagen for several days (with elastic recoil driven by the polyurethane) without the typical matrix contraction by fibroblasts when cultured in 3D collagen gels. We show lung fibroblast-to-myofibroblast differentiation under 30%, 0.1 Hz dynamic strain to validate the model and demonstrate its usefulness for a wide range of tissue engineering applications.