Zeolite-based cataluminescence sensor for the selective detection of acetaldehyde

Rapidly detecting the carcinogen acetaldehyde: preparation and application of a flower-like MoS2 cataluminescence sensor at low working temperature

In this paper, a cataluminescence (CTL) gas sensor based on flower-like molybdenum disulfide (MoS2) is developed. The experimental results show that it has high sensitivity and selectivity to acetaldehyde. The CTL sensor has the advantage of fast response; the response time is about 3 s and the recovery time is about 40 s. The optimal working temperature of this sensor is 174 °C, which is lower than that of the CTL sensors used for acetaldehyde detection in many other reports. Under the optimized conditions, the CTL signal intensity shows a good linear relationship with acetaldehyde concentration (R2 = 0.9991) within the concentration range of 40-2000 ppm, and the detection limit (LOD) is 3.75 ppm. The selectivity experiment results show that the sensor has an obvious response to acetaldehyde and a very weak response to acetic acid, and has no response to many other VOCs (ether, cyclohexane, butyl ether, carbon tetrachloride, ethanol, toluene, formaldehyde, glycerol, trichloromethane and xylene). After 8 repeated measurements for four weeks, the relative standard deviation (RSD) of the CTL sensor is 1.03%, indicating that it has good reproducibility and stability, which shows that the CTL sensor has a promising prospect for the detection of acetaldehyde.

Construction of a Turn-off-on Fluorescent System Based On Aggregation Induced Emission of Acetaldehyde Using Carbonized Polymer dots and Tb3

It was the first time to report the aggregation induced emission (AIE) of acetaldehyde (AA) on the surface of carbonized polymer dots (CPDs) with the auxiliary of Tb³⁺. Based on the AIE of AA, a turn-off-on fluorescence method was established for AA detection using the porous CPDs-Tb³⁺ system. The one-pot hydrothermal method was used to obtain CPDs, using milk and polyethyleneimine (PEI) as precursors. In the presence of Tb³⁺, CPDs aggregated immediately and even forming precipitate, and the fluorescence intensity decreased obviously. AA can effectively embed on the surface of CPDs-Tb³⁺ due to the porous structure. AA displayed obviously blue fluorescence with excitation wavelength at 370 nm (emission peak at 460 nm), while there was no fluorescence peak when excited at 460 nm. In the CPDs-Tb³⁺ solution, AA exhibits obvious fluorescence enhancement effect (λ_ex 460 nm, λ_em 545 nm). And then, AA can be determined by the turn-off-on system based on the linear relationship between fluorescence enhancement and the concentration of AA ranging from 0.04 mM to 42.48 mM. The limit of detection (LOD) was 0.02 mM. The turn-off-on system was successfully applied to determine AA in wine samples. The strategy may be exploited to monitor AA in more drinking or foodstuff samples.

Recent advances in selective formaldehyde detection in biological and environmental samples by fluorometric and colorimetric chemodosimeters

Formaldehyde, a highly reactive carbonyl species, has been widely used in day-to-day life owing to its numerous applications in essential commodities, etc.; the extrusion of formaldehyde from these sources basically leads to increased formaldehyde levels in the environment. Additionally, formaldehyde is endogenously produced in the human body via several biological processes. Considering the adverse effects of formaldehyde, it is highly important to develop an efficient and reliable method for monitoring formaldehyde in environmental and biological samples. Several chemodosimeters (reaction-based sensing probes) have been designed and synthesized to selectively detect the presence of formaldehyde utilizing the photophysical properties of molecules. In this review, we have comprehensively discussed the recent advances in the design principles and sensing mechanisms of developed probes and their biological/environmental applications in selective formaldehyde detection and imaging endogenous formaldehyde in cells. We have summarized the literature based on three different categories: (i) the Schiff base reaction, (ii) the 2-aza-Cope sigmatropic rearrangement reaction and (iii) miscellaneous approaches. In all cases, reactions are accompanied by changes in color and/or emission that can be detected by the naked eye.

4-Hydroxy-2-nonenal, a lipid peroxidation product, as a biomarker in diabetes and its complications: challenges and opportunities

Over 30 million Americans are diagnosed with diabetes and this number is only expected to increase. There are various causes that induce complications with diabetes, including oxidative stress. In oxidative stress, lipid peroxidation-derived reactive carbonyl species such as 4-hydroxy-2-nonenal (4-HNE) is shown to cause damage in organs that leads to diabetic complications. We provided evidence to show that 4-HNE or/and 4-HNE-protein adducts are elevated in various organ systems of diabetic patients and animal models. We then discussed the advantages and disadvantages of different methodologies used for the detection of 4-HNE in diabetic tissues. We also discussed how novel approaches such as electrochemistry and nanotechnology can be used for monitoring 4-HNE levels in biological systems in real-time. Thus, this review enlightens the involvement of 4-HNE in the pathogenesis of diabetes and its complications and efficient methods to identify it. Furthermore, the article presents that 4-HNE can be developed as a biomarker for end-organ damage in diabetes such as diabetic cardiac complications.

A Cataluminescence Sensor Based on NiO Nanoparticles for Sensitive Detection of Acetaldehyde

Sensitive and selective detection of harmful gas is an important task in environmental monitoring. In this work, a gas sensor based on cataluminescence (CTL) for detection of acetaldehyde was designed by using nano-NiO as the sensing material. The sensor shows sensitive response to acetaldehyde at a relatively low working temperature of 200 °C. The linear range of CTL intensity versus acetaldehyde concentration is 0.02–2.5 mg/L, with a limit of detection of 0.006 mg/L at a signal-to-noise ratio of three. Mechanism study shows that electronically excited CO₂ is the excited intermediate for CTL emission during the catalytic oxidation of acetaldehyde on the NiO surface. The proposed sensor has promising application in monitoring acetaldehyde in residential buildings and in the workplace.

Nanostructured Semiconducting Metal Oxide Gas Sensors for Acetaldehyde Detection

Volatile organic compounds (VOCs) are among the most abundant air pollutants. Their high concentrations can adversely affect the human body, and therefore, early detection of VOCs is of outmost importance. Among the different VOCs, in this review paper we have focused our attention to the monitoring of acetaldehyde by chemiresistive gas sensors fabricated from nanostructured semiconducting metal oxides. These sensors can not only provide a high sensing signal for detection of acetaldehyde but also high thermal and mechanical stability along with a low price. This review paper is divided into three major sections. First, we will introduce acetaldehyde as an important VOC and the importance of its detection. Then, the fundamentals of chemiresistive gas sensors will be briefly presented, and in the last section, a survey of the literature on acetaldehyde gas sensors will be presented. The working mechanism of acetaldehyde sensors, their structures, and configurations are reviewed. Finally, the future development outlook and potential applications are discussed, giving a complete panoramic view for researchers working and interested in acetaldehyde detection for different purposes in many fundamental and applicative fields.

The Effect of Zeolite Composition and Grain Size on Gas Sensing Properties of SnO₂/Zeolite Sensor

In order to improve the sensing properties of tin dioxide gas sensor, four kinds of different SiO₂/Al₂O₃ ratio, different particle size of MFI type zeolites (ZSM-5) were coated on the SnO₂ to prepared zeolite modified gas sensors, and the gas sensing properties were tested. The measurement results showed that the response values of ZSM-5 zeolite (SiO₂/Al₂O₃ = 70, grain size 300 nm) coated SnO₂ gas sensors to formaldehyde vapor were increased, and the response to acetone decreased compared with that of SnO₂ gas sensor, indicating an improved selectivity property. The other three ZSM-5 zeolites with SiO₂/Al₂O₃ 70, 150 and 470, respectively, and grain sizes all around 1 μm coated SnO₂ sensors did not show much difference with SnO₂ sensor for the response properties to both formaldehyde and acetone. The sensing mechanism of ZSM-5 modified sensors was briefly analyzed.

Recent advances in cataluminescence-based optical sensing systems

Recent advances in the development of cataluminescence focused on oxygen, temperature, catalyst and instrumentation are summarized.

On–off–on fluorescent oligomer as a chemosensor for the detection of manganese(vii), sulfur(ii) and aldehydes based on the inner filter effect

In this article, a sensitive and selective on–off–on fluorescence chemosensor, Tyloxapol (one kind of water soluble oligomer), was developed for the label-free detection of MnO₄⁻ ions in aqueous solution.

Chromogenic Detection of Aqueous Formaldehyde Using Functionalized Silica Nanoparticles

Silica nanoparticles functionalized with thiol reactive units and bulky polar polyamines were used for the selective colorimetric detection of formaldehyde. The reaction of thiols groups in the nanoparticles surface with a squaraine dye resulted in loss of the π-conjugation of the chromophores, and the subsequent bleaching of the solution. However, when formaldehyde was present in the suspension, the thiol-squaraine reaction was inhibited and a chromogenic response was observed. A selective response to formaldehyde was observed only when the thiol and polyamine groups were anchored to the silica surface. The observed selective response was ascribed to the fact that bulky polyamines generate a highly polar environment around thiols, which were only able to react with the small and polar formaldehyde, but not with other aldehydes. The sensing nanoparticles showed a limit of detection (LOD) for formaldehyde of 36 ppb in water.

Gas sensing using porous materials for automotive applications

The use of zeolites and metal–organic frameworks in the sensing of gases emitted from automobile exhausts is reviewed.

Exploitation of unique properties of zeolites in the development of gas sensors

The unique properties of microporous zeolites, including ion-exchange properties, adsorption, molecular sieving, catalysis, conductivity have been exploited in improving the performance of gas sensors. Zeolites have been employed as physical and chemical filters to improve the sensitivity and selectivity of gas sensors. In addition, direct interaction of gas molecules with the extraframework cations in the nanoconfined space of zeolites has been explored as a basis for developing new impedance-type gas/vapor sensors. In this review, we summarize how these properties of zeolites have been used to develop new sensing paradigms. There is a considerable breadth of transduction processes that have been used for zeolite incorporated sensors, including frequency measurements, optical and the entire gamut of electrochemical measurements. It is clear from the published literature that zeolites provide a route to enhance sensor performance, and it is expected that commercial manifestation of some of the approaches discussed here will take place. The future of zeolite-based sensors will continue to exploit its unique properties and use of other microporous frameworks, including metal organic frameworks. Zeolite composites with electronic materials, including metals will lead to new paradigms in sensing. Use of nano-sized zeolite crystals and zeolite membranes will enhance sensor properties and make possible new routes of miniaturized sensors.

In situ infrared molecular detection using palladium-containing zeolite films

In situ IR detection of carbon monoxide in the presence of hydrocarbons (methanol and pentane) using Pd-containing zeolite thin films is reported. The thin films are prepared by spin coating deposition of nanosized LTL and BEA type zeolites suspensions; the palladium clusters are introduced in the nanosized zeolites by ion exchange followed by γ radiolysis of the coating suspensions. The Pd-containing zeolite films with a thickness of 200 nm are exposed to a single gas (either CO or hydrocarbons) or gas mixtures in the presence of water (100 ppm), and the IR spectra are collected continuously at 25, 75, and 100 °C. The fast recognition of very low concentrations of CO (2-100 ppm) in the presence of highly concentrated vapors of methanol or pentane (400-4000 ppm) with the Pd-containing zeolite films is demonstrated. The detection of CO and hydrocarbons is instant, which is a function of the low thickness of the films, small size of the individual zeolite crystals, and regular size and high stability of the Pd clusters in the zeolite films. The heat of adsorption for all experiments is similar (15 kJ.mol(-1)), which is explained with weak interactions between the carbon monoxide and palladium clusters in the zeolite films at temperatures below 100 °C. The nanosized zeolites with homogeneously distributed Pd clusters deposited in thin films demonstrate high molecular recognition capacity toward low concentrations of carbon monoxide under real environmental conditions, i.e., in the presence of water and hydrocarbons.