The Effects of Trace Yb Doping on the Electrochemical Performance of Li-Rich Layered Oxides

Stabilized Li-Rich Layered Oxide Cathode by a Spontaneously Formed Yb and Oxygen-Vacancy Rich Layer on the Surface

Li-rich layered oxides (LLOs) are among the most promising cathode materials with high theoretical specific capacity (>250 mAh g-1 ). However, capacity decay and voltage hysteresis due tostructural degradation during cycling impede the commercial application of LLOs. Surface engineering and element doping are two methods widely applied tomitigate the structural degradation. Here, it is found that trace amount lanthanide element Yb doping can spontaneously form a surficial Yb-rich layer with high density of oxygen vacancy on the LLO-0.3% Yb (Li1.2 Mn0.54 Co0.13-x Ybx Ni0.13 O2 where x = 0.003) cathodes, which mitigating lattice oxygen loss and the non-preferred layered-to-spinel-to-rock salt tri-phase transition. Meanwhile, there are also some Yb ions doped into the lattice of LLO, which enhance the binding energy with oxygen and stabilize the lattice in grain interior during cycling. The dual effects of Yb doping greatly mitigate the structure degradation during cycling, and facilitate fast diffusion of lithium ions. As a result, the LLO-0.3% Yb sample achieves significantly improved cycling stability, with a capacity retention of 84.69% after 100 cycles at 0.2 C and 84.3% after 200 cycles at 1 C. These finding shighlight the promising rare element doping strategy that can have both surface engineering and doping effects in preparing LLO cathodes with high stability.

Surface Modification Driven Initial Coulombic Efficiency and Rate Performance Enhancement of Li1.2 Mn0.54 Ni0.13 Co0.13 O2 Cathode

Due to its high energy density and low cost, Li-rich Mn-based layered oxides are considered potential cathode materials for next generation Li-ion batteries. However, they still suffer from the serious obstacle of low initial Coulombic efficiency, which is detrimental to their practical application. Here, an efficient surface modification method via NH4 H2 PO4 assisted pyrolysis is performed to improve the Coulombic efficiency of Li1.2 Mn0.54 Ni0.13 Co0.13 O2 , where appropriate oxygen vacancies, Li3 PO4 and spinel phase are synchronously generated in the surface layer of LMR microspheres. Under the synergistic effect of the oxygen vacancies and spinel phase, the unavoidable oxygen release in the cycling process was effectively suppressed. Moreover, the induced Li3 PO4 nanolayer could boost the lithium-ion diffusion and mitigate the dissolution of transition metal ions, especially manganese ions, in the material. The optimally modified sample yielded an impressive initial Coulombic efficiency and outstanding rate performance.

Dual Strategies with Anion/Cation Co-Doping and Lithium Carbonate Coating to Enhance the Electrochemical Performance of Lithium-Rich Layered Oxides

Lithium-rich layered oxides (LLOs, Li1.2 Mn0.54 Ni0.13 Co0.13 O2 ) are widely used as cathode materials for lithium-ion batteries due to its high specific capacity, high operating voltage and low cost. However, the LLOs are faced with rapid decay of charge/discharge capacity and voltage, as well as interface side reactions, which limit its electrochemical performance. Herein, the dual strategies of sulfite/sodium ion co-doping and lithium carbonate coating were used to improve it. It founds that modified LLOs achieve 88.74 % initial coulomb efficiency, 295.3 mAh g-1 first turn discharge capacity, in addition to 216.9 mAh g-1 at 1 C, and 87.23 % capacity retention after 100 cycles. Mechanism research indicated that the excellent electrochemical performance benefits from the doping of both Na+ and SO3 2- , and it could significantly reduce the migration energy barrier of Li+ and promote Li+ migration. Meanwhile, anion and cation are co-doped greatly reduces the band gap of LLOs and increase its electrical conductivity, and its binding effect on Li+ is weakened, making it easier for Li+ to shuttle through the material. In addition, the lithium carbonate coating significantly inhibits the occurrence of interfacial side reactions of LLOs. This work provides a theoretical basis and practical guidance for the further development of LLOs with higher electrochemical performance.

Recent advances in lithium-rich manganese-based cathodes for high energy density lithium-ion batteries

The development of society challenges the limit of lithium-ion batteries (LIBs) in terms of energy density and safety. Lithium-rich manganese oxide (LRMO) is regarded as one of the most promising cathode materials owing to its advantages of high voltage and specific capacity (more than 250 mA h g^-1) as well as low cost. However, the problems of fast voltage/capacity fading, poor rate performance and the low initial Coulombic efficiency severely hinder its practical application. In this paper, we review the latest research advances of LRMO cathode materials, including crystal structure, electrochemical reaction mechanism, existing problems and modification strategies. In this review, we pay more attention to recent progress in modification methods, including surface modification, doping, morphology and structure design, binder and electrolyte additives, and integration strategies. It not only includes widely studied strategies such as composition and process optimization, coating, defect engineering, and surface treatment, but also introduces many relatively novel modification methods, such as novel coatings, grain boundary coating, gradient design, single crystal, ion exchange method, solid-state batteries and entropy stabilization strategy. Finally, we summarize the existing problems in the development of LRMO and put forward some perspectives on the further research.

Dual Substitution Strategy in Co-Free Layered Cathode Materials for Superior Lithium Ion Batteries

A dual substitution strategy is introduced to Co-free layered material LiNi_0.5Mn_0.5O₂ by partially replacing Li and Ni with Na and Al, respectively, to achieve a superior cathode material for lithium ion batteries. Na⁺ ion functions as a "pillar" and a " cationic barrier" in the lithium layer while Al³⁺ ion plays an auxiliary role in stabilizing structure and lattice oxygen to improve the electrochemical performance and safety. The stability of lattice oxygen comes from the binding energy between the Ni and O, which is larger due to higher valences of Ni ions, along with a stronger Al-O bond in the crystal structure and the "cationic barrier" effect of Na⁺ ion at the high-charge. The more stable lattice oxygen reduces the cation disorder in cycling, and Na⁺ in the Li layer squeezes the pathway of the transition metal from the LiM₂ (M = metal) layer to the Li layer, stabilizing the layered crystal structure by inhibiting the electrochemical-driven cation disorder. Moreover, the cathode with Na-Al dual-substitution displays a smaller volume change, yielding a more stable structure. This study unravels the influence of Na-Al dual-substitution on the discharge capacity, midpoint potential, and cyclic stability of Co-free layered cathode materials, which is crucial for the development of lithium ion batteries.

New Insights into the Mechanism of Enhanced Performance of Li[Ni0.8Co0.1Mn0.1]O2 with a Polyacrylic Acid-Modified Binder

A binder is an important component in lithium-ion batteries and plays a significant role in maintaining the properties of active substances. Most studies in the field of binders have only focussed on physical properties such as bonding performance. Here, a polyacrylic acid-modified binder was designed and adapted to Li[Ni_0.8Co_0.1Mn_0.1]O₂, which enhanced the electrochemical stability of Li[Ni_0.8Co_0.1Mn_0.1]O₂ from 30.2 to 66.6% (300 cycles at 1 C). We for the first time discovered that this was caused by a chemical reaction between polyacrylic acid and the residual lithium on the surface during the cycling, which formed a lithium propionic acid coating layer and maintained the stability of the layered structure.