Surface Characterization of Biopolymer Micropatterns Processed by Ion-Beam Modification and PECVD

High-resolution, high-throughput, positive-tone patterning of poly(ethylene glycol) by helium beam exposure through stencil masks

In this work, a collimated helium beam was used to activate a thiol-poly(ethylene glycol) (SH-PEG) monolayer on gold to selectively capture proteins in the exposed regions. Protein patterns were formed at high throughput by exposing a stencil mask placed in proximity to the PEG-coated surface to a broad beam of helium particles, followed by incubation in a protein solution. Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR) spectra showed that SH-PEG molecules remain attached to gold after exposure to beam doses of 1.5-60 µC/cm(2) and incubation in PBS buffer for one hour, as evidenced by the presence of characteristic ether and methoxy peaks at 1120 cm(-1) and 2870 cm(-1), respectively. X-ray Photoelectron Spectroscopy (XPS) spectra showed that increasing beam doses destroy ether (C-O) bonds in PEG molecules as evidenced by the decrease in carbon C1s peak at 286.6 eV and increased alkyl (C-C) signal at 284.6 eV. XPS spectra also demonstrated protein capture on beam-exposed PEG regions through the appearance of a nitrogen N1s peak at 400 eV and carbon C1s peak at 288 eV binding energies, while the unexposed PEG areas remained protein-free. The characteristic activities of avidin and horseradish peroxidase were preserved after attachment on beam-exposed regions. Protein patterns created using a 35 µm mesh mask were visualized by localized formation of insoluble diformazan precipitates by alkaline phosphatase conversion of its substrate bromochloroindoyl phosphate-nitroblue tetrazolium (BCIP-NBT) and by avidin binding of biotinylated antibodies conjugated on 100 nm gold nanoparticles (AuNP). Patterns created using a mask with smaller 300 nm openings were detected by specific binding of 40 nm AuNP probes and by localized HRP-mediated deposition of silver nanoparticles. Corresponding BSA-passivated negative controls showed very few bound AuNP probes and little to no enzymatic formation of diformazan precipitates or silver nanoparticles.

Physical vs photolithographic patterning of plasma polymers: an investigation by ToF-SSIMS and multivariate analysis

Physical and photolithographic techniques are commonly used to create chemical patterns for a range of technologies including cell culture studies, bioarrays and other biomedical applications. In this paper, we describe the fabrication of chemical micropatterns from commonly used plasma polymers. Atomic force microscopy (AFM) imaging, time-of-flight static secondary ion mass spectrometry (ToF-SSIMS) imaging, and multivariate analysis have been employed to visualize the chemical boundaries created by these patterning techniques and assess the spatial and chemical resolution of the patterns. ToF-SSIMS analysis demonstrated that well-defined chemical and spatial boundaries were obtained from photolithographic patterning, while the resolution of physical patterning via a transmission electron microscopy (TEM) grid varied depending on the properties of the plasma system including the substrate material. In general, physical masking allowed diffusion of the plasma species below the mask and bleeding of the surface chemistries. Multivariate analysis techniques including principal component analysis (PCA) and region of interest (ROI) assessment were used to investigate the ToF-SSIMS images of a range of different plasma polymer patterns. In the most challenging case, where two strongly reacting polymers, allylamine and acrylic acid were deposited, PCA confirmed the fabrication of micropatterns with defined spatial resolution. ROI analysis allowed for the identification of an interface between the two plasma polymers for patterns fabricated using the photolithographic technique which has been previously overlooked. This study clearly demonstrated the versatility of photolithographic patterning for the production of multichemistry plasma polymer arrays and highlighted the need for complementary characterization and analytical techniques during the fabrication plasma polymer micropatterns.

Immobilization of poly (ethylene imine) on poly (L-lactide) promotes MG63 cell proliferation and function

Poly (ethylene imine) (PEI) is a polycation widely used for DNA transfection to cells but also applied as primary polycation for layer-by-layer (LBL) assembly of polyelectrolytes. The aim of the present study was to investigate the effect of modification with PEI on the biocompatibility of poly (L-lactide) (PLLA) films. PEI with different molecular weight was immobilized on PLLA by either adsorption or covalent binding. Cell morphologies, immuno-fluorescence staining, cell proliferation by lactate dehydrogenase assay and cell differentiation by alkaline phosphatase assay were utilized to assess the biocompatibility of the modified PLLA using osteoblast cell line MG63. Results revealed that PEI modification remarkably improved cell adhesion, viability, proliferation and function compared with plain PLLA. Hence, PEI-modified PLLA is acceptable as transfection vehicle for engineering of bone and other tissues, or as primary layer to allow LBL assembly to generate biomimetic surface coatings.