Application of green-synthesized carbon dots for imaging of cancerous cell lines and detection of anthraquinone drugs using silica-coated CdTe quantum dots-based ratiometric fluorescence sensor

Chemotherapy drugs of daunorubicin and doxorubicin treat cancers with many side effects. So, detection of them in the biological system for regulation and controlling of usage is essential. In this study, a ratiometric fluorescent method was introduced for detection of daunorubicin and doxorubicin using bell pepper-based carbon dots, as the variable signal, and silica-coated CdTe quantum dots, as the constant signal. The detection was done based on variations of carbon dots intensity in the presence of drugs in comparison with the constant intensity of silica-coated CdTe quantum dots. The proposed ratiometric fluorescent method was successfully used for detection of daunorubicin and doxorubicin range of 54.37-13594.34 nmolL^-1 and 86.2-17242 nmolL^-1, with a detection limit of 18.53 nmolL^-1 and 29 nmolL^-1, respectively. Also, this method was used for detection of drugs in serum samples with recovery ranges of 86.14-99.62 (RSD 3-1.47%) and 86.32-97.53 (3.38-1.48%), respectively. Finally, after evaluation of carbon dots toxicity by MTT test, carbon dots was applied for imaging of prostate cancer cell lines (PC-3) and breast cancer cell lines (MCF7). The results demonstrated that despite improvement of the repeatability and interferences reduction by ratiometric method, also carbon dots were successfully applied for imaging of cell lines.

An electrochemical daunorubicin sensor based on the use of platinum nanoparticles loaded onto a nanocomposite prepared from nitrogen decorated reduced graphene oxide and single-walled carbon nanotubes

A glassy carbon electrode (GCE) was modified with a nanocomposite prepared from nitrogen-doped reduced graphene oxide (N-rGO) and single walled carbon nanotubes (SWCNTs), and then loaded with platinum nanoparticles (Pt NPs) to obtain a voltammetric sensor for daunorubicin (DNR). Reductive doping of GO and the crystallization of the Pt NPs were carried out in a one-step hydrothermal process. The modified electrode was characterized by cyclic voltammetry and differential pulse voltammetry. It exhibited high sensitivity compared with unmodified electrode. Some experimental parameters which affected sensor response were optimized. Under optimum conditions and at a working voltage of typically -0.56 V (vs. Ag/AgCl), the sensor has a low detection limit (3 ng mL^-1), a wide linear range (0.01-6 μg mL^-1) and good long-term stability. The method was successfully applied to the sensitive and rapid determination of DNR in spiked human serum samples. Graphical abstract Platinum nanoparticles were loaded onto a nanocomposite prepared from nitrogen decorated reduced graphene oxide and single-walled carbon nanotubes (N-rGO-SWCNTs-Pt) and then used for electrochemical determination of daunorubicin (DNR).

Nanobiosensing with Arrays and Ensembles of Nanoelectrodes

Since the first reports dating back to the mid-1990s, ensembles and arrays of nanoelectrodes (NEEs and NEAs, respectively) have gained an important role as advanced electroanalytical tools thank to their unique characteristics which include, among others, dramatically improved signal/noise ratios, enhanced mass transport and suitability for extreme miniaturization. From the year 2000 onward, these properties have been exploited to develop electrochemical biosensors in which the surfaces of NEEs/NEAs have been functionalized with biorecognition layers using immobilization modes able to take the maximum advantage from the special morphology and composite nature of their surface. This paper presents an updated overview of this field. It consists of two parts. In the first, we discuss nanofabrication methods and the principles of functioning of NEEs/NEAs, focusing, in particular, on those features which are important for the development of highly sensitive and miniaturized biosensors. In the second part, we review literature references dealing the bioanalytical and biosensing applications of sensors based on biofunctionalized arrays/ensembles of nanoelectrodes, focusing our attention on the most recent advances, published in the last five years. The goal of this review is both to furnish fundamental knowledge to researchers starting their activity in this field and provide critical information on recent achievements which can stimulate new ideas for future developments to experienced scientists.

Electrochemical synthesis of nanostructured gold film for the study of carbohydrate-lectin interactions using localized surface plasmon resonance spectroscopy

Localized surface plasmon resonance (LSPR) spectroscopy is a label-free chemical and biological molecular sensing technique whose sensitivity depends upon development of nanostructured transducers. Herein, we report an electrodeposition method for fabricating nanostructured gold films (NGFs) that can be used as transducers in LSPR spectroscopy. The NGF was prepared by electrodepositing gold from potassium dicyanoaurate solution onto a flat gold surface using two sequential controlled potential steps. Imaging by scanning electron microscopy reveals a morphology consisting of randomly configured block-like nanostructures. The bulk refractive index sensitivity of the prepared NGF is 100±2 nmRIU(-1) and the initial peak in the reflectance spectrum is at 518±1 nm under N2(g). The figure of merit is 1.7. In addition, we have studied the interaction between carbohydrate (mannose) and lectin (Concanavalin A) on the NGF surface using LSPR spectroscopy by measuring the interaction of 8-mercaptooctyl-α-d-mannopyranoside (αMan-C8-SH) with Concanavalin A by first immobilizing αMan-C8-SH in mixed SAMs with 3,6-dioxa-8-mercaptooctanol (TEG-SH) on the NGF surface. The interaction of Con A with the mixed SAMs is confirmed using electrochemical impedance spectroscopy. Finally, the NGF surface was regenerated to its original sensitivity by removing the SAM and the bound biomolecules. The results from these experiments contribute toward the development of inexpensive LSPR based sensors that could be useful for studying glycan-protein interactions and other bioanalytical purposes.

Electrochemical annealing of nanoporous gold by application of cyclic potential sweeps

An electrochemical method for annealing the pore sizes of nanoporous gold (NPG) is reported. The pore sizes of NPG can be increased by electrochemical cycling with the upper potential limit being just at the onset of gold oxide formation. This study has been performed in electrolyte solutions including potassium chloride, sodium nitrate and sodium perchlorate. Scanning electron microscopy images have been used for ligament and pore size analysis. We examine the modifications of NPG due to annealing using electrochemical impedance spectroscopy, and cyclic voltammetry and offer a comparison of the surface coverage using the gold oxide stripping method as well as the method in which electrochemically accessible surface area is determined by using a diffusing redox probe. The effect of additives adsorbed on the NPG surface when subjected to annealing in different electrolytes as well as the subsequent structural changes in NPG are also reported. The effect of the annealing process on the application of NPG as a substrate for glucose electro-oxidation is briefly examined.

Fabrication and modeling of an ultrasensitive label free impedimetric immunosensor for Aflatoxin B1based on poly(o-phenylenediamine) modified gold 3D nano electrode ensembles

An ultrasensitive label free impedimetric immunosensor for AFB₁detection was fabricated based on poly(o-phenylenediamine) (PoPD) electropolymerized film modified gold three dimensional nanoelectrode ensembles (3DNEEs).

Electrochemical characterization of globotriose-containing self-assembled monolayers on nanoporous gold and their binding of soybean agglutinin

Self-assembled monolayers (SAMs) of α-D-Gal-(1→4)-β-D-Gal-(1→4)-β-D-Glc-mercaptooctane (globotriose, Gb3-C8-SH) were prepared both as single-component SAMs and as mixed SAMs with either octanethiol (OCT) or 8-mercapto-3,6-dioxaoctanol (HO-PEG2-SH), on flat gold and on nanoporous gold (NPG) electrodes. The binding of soybean agglutinin (SBA) to the globotriose (Gb3) unit in the SAMs was then studied using electrochemical impedance spectroscopy (EIS), which is a label free method found to be quite sensitive to SAM composition and to the differences in SAM structure on NPG versus on flat Au. The affinity of SBA to the mixed SAM of HO-PEG2-SH and Gb3-C8-SH on NPG is found to be greater on NPG than on flat gold, and indicates a potential advantage for NPG as a substrate. The SAMs of HO-PEG2-SH were found to resist protein adsorption on either NPG or flat gold. The non-specific adsorption of SBA to OCT SAMs on flat Au was observed in EIS by the increase in charge transfer resistance; whereas, the increase seen on the NPG surface was smaller, and suggests that EIS measurements on NPG are less affected by non-specific protein adsorption. Atomic force microscopy (AFM) images of the SBA binding to mixed SAM of HO-PEG2-SH and Gb3-C8-SH on NPG showed a greater number of proteins on top of the OCT containing SAMs.

Surface area and pore size characteristics of nanoporous gold subjected to thermal, mechanical, or surface modification studied using gas adsorption isotherms, cyclic voltammetry, thermogravimetric analysis, and scanning electron microscopy

Nitrogen adsorption/desorption isotherms are used to investigate the Brunauer, Emmett, and Teller (BET) surface area and Barrett-Joyner-Halenda (BJH) pore size distribution of physically modified, thermally annealed, and octadecanethiol functionalized np-Au monoliths. We present the full adsorption-desorption isotherms for N(2) gas on np-Au, and observe type IV isotherms and type H1 hysteresis loops. The evolution of the np-Au under various thermal annealing treatments was examined using scanning electron microscopy (SEM). The images of both the exterior and interior of the thermally annealed np-Au show that the porosity of all free standing np-Au structures decreases as the heat treatment temperature increases. The modification of the np-Au surface with a self-assembled monolayer (SAM) of C(18)-SH (coverage of 2.94 × 10(14) molecules cm(-2) based from the decomposition of the C(18)-SH using thermogravimetric analysis (TGA)), was found to reduce the strength of the interaction of nitrogen gas with the np-Au surface, as reflected by a decrease in the 'C' parameter of the BET equation. From cyclic voltammetry studies, we found that the surface area of the np-Au monoliths annealed at elevated temperatures followed the same trend with annealing temperature as found in the BET surface area study and SEM morphology characterization. The study highlights the ability to control free-standing nanoporous gold monoliths with high surface area, and well-defined, tunable pore morphology.

Comparative Study of the Binding of Concanavalin A to Self-Assembled Monolayers Containing a Thiolated α-Mannoside on Flat Gold and on Nanoporous Gold

We have prepared SAMs containing 8-mercaptooctyl α-D-mannopyranoside, either as a single component or in mixed SAMs with n-octanethiol on flat gold surfaces and on nanoporous gold. Electrochemical impedance spectroscopy showed that the mixed SAMs on flat gold surfaces showed the highest Con A binding near 1:9 solution molar ratio of thiolatedα-mannoside to n-octanethiol whereas those on NPG showed the highest response at 1:19 solution molar ratio of thiolated α-mannoside to n-octanethiol. Atomic force microscopy was employed to image the monolayers, and also to image the bound Con A protein.

Polycarbonate-based ordered arrays of electrochemical nanoelectrodes obtained by e-beam lithography

Ordered arrays of nanoelectrodes for electrochemical use are prepared by electron beam lithography (EBL) using polycarbonate as a novel e-beam resist. The nanoelectrodes are fabricated by patterning arrays of holes in a thin film of polycarbonate spin-coated on a gold layer on Si/Si(3)N(4) substrate. Experimental parameters for the successful use of polycarbonate as high resolution EBL resist are optimized. The holes can be filled partially or completely by electrochemical deposition of gold. This enables the preparation of arrays of nanoelectrodes with different recession degree and geometrical characteristics. The polycarbonate is kept on-site and used as the insulator that separates the nanoelectrodes. The obtained nanoelectrode arrays (NEAs) exhibit steady state current controlled by pure radial diffusion in cyclic voltammetry for scan rates up to approximately 50 mV s( - 1). Electrochemical results showed satisfactory agreement between experimental voltammograms and suitable theoretical models. Finally, the peculiarities of NEAs versus ensembles of nanoelectrodes, obtained by membrane template synthesis, are critically evaluated.