Influence of environmental conditions in bovine bone ablation by ultrafast laser

Orthopedics-Related Applications of Ultrafast Laser and Its Recent Advances

The potential of ultrafast lasers (pico- to femtosecond) in orthopedics-related procedures has been studied extensively for clinical adoption. As compared to conventional laser systems with continuous wave or longer wave pulse, ultrafast lasers provide advantages such as higher precision and minimal collateral thermal damages. Translation to surgical applications in the clinic has been restrained by limitations of material removal rate and pulse average power, whereas the use in surface texturing of implants has become more refined to greatly improve bioactivation and osteointegration within bone matrices. With recent advances, we review the advantages and limitations of ultrafast lasers, specifically in orthopedic bone ablation as well as bone implant laser texturing, and consider the difficulties encountered within orthopedic surgical applications where ultrafast lasers could provide a benefit. We conclude by proposing our perspectives on applications where ultrafast lasers could be of advantage, specifically due to the non-thermal nature of ablation and control of cutting.

Effects of water cooling on laser‐induced thermal damage in rat hepatectomy

Purpose

High‐powered lasers are commonly used for tissue resection in surgeries, including liver resection, medically known as hepatectomy; however, such lasers inevitably induce thermal damage that causes postoperative complications. This study aims to explore the effects of water cooling and different laser output modes on laser‐induced thermal damage during hepatectomy.

Methods

To avoid the influence of superposition, a 980‐nm diode laser was used for a single‐point hepatectomy. Eighteen Sprague–Dawley rats were used to explore the effects of water cooling and different laser output modes. A constant energy 10‐J laser was used to cut the liver tissue with a power of 10 W and time of 1 second. The rats were randomly divided into six groups. The first three groups were assigned as test subjects for different laser output modes. Group 1 was operated with a continuous laser output for a duration of 1 second. Groups 2 and 3 were operated with a pulsed laser output for a duration of 1 second and a pulse width of 0.5 and 0.25 seconds, respectively. Groups 4, 5, and 6 were assigned for the water cooling test. Water cooling was performed based on the parameters of the first three groups. Medical saline (0.9% NaCl) was used for water cooling. The main observation indicators were resection efficiency and thermal damage, including the area of the thermal damage zone. Resection efficiency is calculated by dividing the resection area by the total thermal damage area.

Results

In the three water cooling groups, the area of the resection, carbonized, sub‐boiling coagulated, and total thermal damage zones were 0.0677, 0.00, 1.7293, and 2.2982 mm² in Group 4; 0.0465, 0.00, 1.3205, and 1.8414 mm² in Group 5; and 0.0565, 0.00, 1.4301, and 1.9650 mm² in Group 6, respectively. Compared with the first three groups, the water cooling groups exhibited significantly reduced thermal damage areas of in the carbonized, sub‐boiling coagulated, and total thermal damage zones (p < 0.001 for all). In addition, there was no statistical difference in the resection area, vacuolated area, and resection efficiency. Furthermore, there was no statistical difference in the area of each thermal damage zone between the continuous and pulsed output groups. The resection efficiencies were 4.82%, 3.34%, 3.73%, 3.93%, 3.36%, and 3.01% in Groups 1 to 6, respectively. Moreover, there was no statistical difference (p > 0.05) in the resection efficiencies.

Conclusion

Water cooling can reduce the total laser‐induced thermal damage area and prevent tissue carbonization. Therefore, this cooling method can be used as a simple and safe strategy for controlling thermal damage during hepatectomy.

In vitro evaluation of ultrafast laser drilling large-size holes on sheepshank bone

Bone drilling has been widely used in medical surgeries such as repair and fixation in orthopedics. Traditional drilling method using drill-bits inevitably causes significant thermal and mechanical trauma in the adjacent bone tissues. This paper demonstrates the feasibility of femtosecond laser drilling in vitro large-size holes on the sheepshank bone with high efficiency and minimal collateral damage. A Yb:KGW femtosecond laser was utilized to drill millimeter-scale holes on the bone under different cooling conditions including gas- and water-assisted processes. Scanning electron microscopy, confocal laser scanning microscopy and infrared thermographic imaging system were used to investigate the residual debris, removal rate, bone temperature variation and hole morphology. Histological examination, Fourier transform infrared spectroscopy and Raman spectroscopy were employed to study thermal damage. Results show that a 4 mm hole with smooth and clean surface was successfully drilled on the bone, and the highest removal rate of 0.99 mm³/s was achieved, which was twenty times higher than the previous study of 0.05 mm³/s. Moreover, bone and bone marrow were distinguished by real-time monitoring system during laser drilling. This work demonstrates the potential for clinical applications using an ultrafast laser to produce crack-free large-size bone holes.