Irreversible electroporation for the ablation of pancreatic malignancies: A patient-specific methodology

Integrated Time Nanosecond Pulse Irreversible Electroporation (INSPIRE): Assessment of Dose, Temperature, and Voltage on Experimental and Clinical Treatment Outcomes

OBJECTIVE

This study sought to investigate a novel strategy using temperature-controlled delivery of nanosecond pulsed electric fields as an alternative to the 50-100 microsecond pulses used for irreversible electroporation.

METHODS

INSPIRE treatments were carried out at two temperatures in 3D tumor models using doses between 0.001 s and 0.1 s. The resulting treatment zones were quantified using viability staining and lethal electric field intensities were determined numerically. Computational modeling was then used to determine parameters necessary for INSPIRE treatments to achieve equivalent treatment zones to clinical electroporation treatments and evaluate the potential for these treatments to induce deleterious thermal damage.

RESULTS

Lethal thresholds between 1109 and 709 V/cm were found for nominal 0.01 s treatments with pulses between 350 ns and 2000 ns at physiological temperatures. Further increases in dose resulted in significant decreases in lethal thresholds. Given these experimental results, treatment zones comparable to clinical electroporation are possible by increasing the dose and voltage used with nanosecond duration pulses. Temperature-controlled simulations indicate minimal thermal cell death while achieving equivalent treatment volumes to clinical electroporation.

CONCLUSION

Nanosecond electrical pulses can achieve comparable outcomes to traditional electroporation provided sufficient electrical doses or voltages are applied. The use of temperature-controlled delivery may minimize thermal damage during treatment.

SIGNIFICANCE

Intense muscle stimulation and the need for cardiac gating have limited irreversible electroporation. Nanosecond pulses can alleviate these challenges, but traditionally have produced significantly smaller treatment zones. This study suggests that larger ablation volumes may be possible with the INSPIRE approach and that future in vivo studies are warranted.

An overview of the irreversible electroporation for the treatment of liver metastases: When to use it

Tumour ablation is an established therapy for local treatment of liver metastases and hepatocellular carcinoma. Most commonly two different kind of thermic ablation, radiofrequency ablation and microwave ablation, are used in clinical practice. The aim of both is to induce thermic damage to the malignant cells in order to obtain coagulative necrosis of the neoplastic lesions. Our main concerns about these procedures are the collateral thermic damage to adjacent structures and heat-sink effect. Irreversible electroporation (IRE) is a recently developed, non-thermal ablation procedure which works applying short pulses of direct current that generate an electric field in the lesion area. The electric field increase the transmembrane potential, changing its permeability to ions.Irreversible electroporation does not generate heat, giving the chance to avoid the heat-sink effect and opening the path to a better treatment of all the lesions located in close proximity to big vessels and bile ducts. Electric fields produced by the IRE may affect endothelial cells and cholangiocytes but they spare the collagen matrix, preserving re-epithelization process as well as the function of the damaged structures. Purpose of the authors is to identify the different scenarios where CT-guided percutaneous IRE of the liver should be preferred to other ablative techniques and why.

Improving Prediction of the Potential Distribution Induced by Cylindrical Electrodes within a Homogeneous Rectangular Grid during Irreversible Electroporation

Background: Irreversible electroporation (IRE) is an ablation technique based on the application of short, high-voltage pulses between needle electrodes (diameter: ~1.0 × 10−3 m). A Finite Difference-based software simulating IRE treatment generally uses rectangular grids, yielding discretization issues when modeling cylindrical electrodes and potentially affecting the validity of treatment planning simulations. Aim: Develop an Electric-Potential Estimation (EPE) method for accurate prediction of the electric-potential distribution in the vicinity of cylindrical electrodes. Methods: The electric-potential values in the voxels neighboring the cylindrical electrode voxels were corrected based on analytical solutions derived for coaxial/cylindrical electrodes. Simulations at varying grid resolutions were validated using analytical models. Low-resolution heterogeneous simulations at 2.0 × 10−3 m excluding/including EPE were compared with high-resolution results at 0.25 × 10−3 m. Results: EPE significantly reduced maximal errors compared to analytical results for the electric-potential distributions (26.6–71.8%→0.4%) and for the electrical resistance (30%→1–6%) at 3.0 × 10−3 m voxel-size. EPE significantly improved the mean-deviation (43.1–52.8%→13.0–24.3%) and the calculation-time gain (>15,000×) of low-resolution compared to high-resolution heterogeneous simulations. Conclusions: EPE can accurately predict the potential distribution of neighboring cylindrical electrodes, regardless of size, position, and orientation in a rectangular grid. The simulation time of treatment planning can therefore be shortened by using large voxel-sized models without affecting accuracy of the electric-field distribution, enabling real-time clinical IRE treatment planning.

Polymer Nanoparticles Enhance Irreversible Electroporation In Vitro

Expanding the volume of an irreversible electroporation treatment typically necessitates an increase in pulse voltage, number, duration, or repetition. This study investigates the addition of polyethylenimine nanoparticles (PEI-NP) to pulsed electric field treatments, determining their combined effect on ablation size and voltages. U118 cells in an in vitro 3D cell culture model were treated with one of three pulse parameters (with and without PEI-NPs) which are representative of irreversible electroporation (IRE), high frequency irreversible electroporation (H-FIRE), or nanosecond pulsed electric fields (nsPEF). The size of the ablations were compared and mapped onto an electric field model to describe the electric field required to induce cell death. Analysis was conducted to determine the role of PEI-NPs in altering media conductivity, the potential for PEI-NP degradation following pulsed electric field treatment, and PEI-NP uptake. Results show there was a statistically significant increase in ablation diameter for IRE and H-FIRE pulses with PEI-NPs. There was no increase in ablation size for nsPEF with PEI-NPs. This all occurs with no change in cell media conductivity, no observable degradation of PEI-NPs, and moderate particle uptake. These results demonstrate the synergy of a combined cationic polymer nanoparticle and pulsed electric field treatment for the ablation of cancer cells. These results set the foundation for polymer nanoparticles engineered specifically for irreversible electroporation.

Local ablation of pancreatic tumors: State of the art and future perspectives

BACKGROUND

Currently, the technologies most commonly used to treat locally advanced pancreatic cancer are radiofrequency ablation (RFA), microwave ablation, and irreversible (IRE) or reversible electroporation combined with low doses of chemotherapeutic drugs.

AIM

To report an overview and updates on ablative techniques in pancreatic cancer.

METHODS

Several electronic databases were searched. The search covered the years from January 2000 to January 2021. Moreover, the reference lists of the found papers were analysed for papers not indexed in the electronic databases. All titles and abstracts were analysed.

RESULTS

We found 30 studies (14 studies for RFA, 3 for microwave therapy, 10 for IRE, and 3 for electrochemotherapy), comprising 1047 patients, which were analysed further. Two randomized trials were found for IRE. Percutaneous and laparotomy approaches were performed. In the assessed patients, the median maximal diameter of the lesions was in the range of 2.8 to 4.5 cm. All series included patients unfit for surgical treatment, but Martin et al assessed a subgroup of patients with borderline resectable tumours who underwent resection with margin attenuation with IRE. Most studies administered chemotherapy prior to ablative therapies. However, several studies suggest that the key determinant of improved survival is attributable to ablative treatment alone. Nevertheless, the authors suggested chemotherapy before local therapies for several reasons. This strategy may not only downstage a subgroup of patients to curative-intent surgery but also support to recognize patients with biologically unfavourable tumours who would likely not benefit from ablation treatments. Ablation therapies seem safe based on the 1047 patients assessed in this review. The mortality rate ranged from 1.8% to 2%. However, despite the low mortality, the reported rates of severe post procedural complications ranged from 0%-42%. Most reported complications have been self-limiting and manageable. Median overall survival varied between 6.0 and 33 mo. Regarding the technical success rate, assessed papers reported an estimated rate in the range of 85% to 100%. However, the authors reported early recurrence after treatment. A distinct consideration should be made on whether local treatments induce an immune response in the ablated area. Preclinical and clinical studies have shown that RFA is a promising mechanism for inducing antigen-presenting cell infiltration and enhancing the systemic antitumour T-cell immune response and tumour regression.

CONCLUSION

In the management of patients with pancreatic cancer, the possibility of a multimodal approach should be considered, and conceptually, the combination of RFA with immunotherapy represents a novel angle of attack against this tumour.

EView: An electric field visualization web platform for electroporation-based therapies

BACKGROUND AND OBJECTIVES

Electroporation is the phenomenon by which cell membrane permeability to ions and macromolecules is increased when the cell is briefly exposed to high electric fields. In electroporation-based treatments, such exposure is typically performed by delivering high voltage pulses across needle electrodes in tissue. For a given tissue and pulsing protocol, an electric field magnitude threshold exists that must be overreached for treatment efficacy. However, it is hard to preoperatively infer the treatment volume because the electric field distribution intricately depends on the electrodes' positioning and length, the applied voltage, and the electric conductivity of the treated tissues. For illustrating such dependencies, we have created EView (https://eview.upf.edu), a web platform that estimates the electric field distribution for arbitrary needle electrode locations and orientations and overlays it on 3D medical images.

METHODS

A client-server approach has been implemented to let the user set the electrode configuration easily on the web browser, whereas the simulation is computed on a dedicated server. By means of the finite element method, the electric field is solved in a 3D volume. For the sake of simplicity, only a homogeneous tissue is modeled, assuming the same properties for healthy and pathologic tissues. The non-linear dependence of tissue conductivity on the electric field due to the electroporation effect is modeled. The implemented model has been validated against a state of the art finite element solver, and the server has undergone a heavy load test to ensure reliability and to report execution times.

RESULTS

The electric field is rapidly computed for any electrode and tissue configuration, and alternative setups can be easily compared. The platform provides the same results as the state of the art finite element solver (Dice = 98.3 ± 0.4%). During the high load test, the server remained responsive. Simulations are computed in less than 2 min for simple cases consisting of two electrodes and take up to 40 min for complex scenarios consisting of 6 electrodes.

CONCLUSIONS

With this free platform we provide expert and non-expert electroporation users a way to rapidly model the electric field distribution for arbitrary electrode configurations.

Temperature Dependence of High Frequency Irreversible Electroporation Evaluated in a 3D Tumor Model

Electroporation is a bioelectric phenomenon used to deliver target molecules into cells in vitro and irreversible electroporation (IRE) is an emerging cancer therapy used to treat inoperable tumors in situ. These phenomena are generally considered to be non-thermal in nature. In this study, a 3D tumor model was used to investigate the correlation between temperature and the effectiveness of standard clinical IRE and high frequency (H-FIRE) protocols. It was found for human glioblastoma cells that in the range of 2 to 37 °C the H-FIRE lethal electric field threshold value, which describes the minimum electric field to cause cell death, is highly dependent on temperature. Increasing the initial temperature from 2 to 37 °C resulted in a significant decrease in lethal electric field threshold from 1168 to 507 V/cm and a 139% increase in ablation size for H-FIRE burst treatments. Standard clinical protocol IRE treatments resulted in a decrease in lethal threshold from 485 to 453 V/cm and a 7% increase in ablation size over the same temperature range. Similar results were found for pancreatic cancer cells which indicate that tissue temperature may be a significant factor affecting H-FIRE ablation size and treatment planning in vivo while lower temperatures may be useful in maintaining cell viability for transfection applications.

High-Frequency Irreversible Electroporation for Treatment of Primary Liver Cancer: A Proof-of-Principle Study in Canine Hepatocellular Carcinoma

PURPOSE

To determine the safety and feasibility of percutaneous high-frequency irreversible electroporation (HFIRE) for primary liver cancer and evaluate the HFIRE-induced local immune response.

MATERIALS AND METHODS

HFIRE therapy was delivered percutaneously in 3 canine patients with resectable hepatocellular carcinoma (HCC) in the absence of intraoperative paralytic agents or cardiac synchronization. Pre- and post-HFIRE biopsy samples were processed with histopathology and immunohistochemistry for CD3, CD4, CD8, and CD79a. Blood was collected on days 0, 2, and 4 for complete blood count and chemistry. Numeric models were developed to determine the treatment-specific lethal thresholds for malignant canine liver tissue and healthy porcine liver tissue.

RESULTS

HFIRE resulted in predictable ablation volumes as assessed by posttreatment CT. No detectable cardiac interference and minimal muscle contraction occurred during HFIRE. No clinically significant adverse events occurred secondary to HFIRE. Microscopically, a well-defined ablation zone surrounded by a reactive zone was evident in the majority of samples. This zone was composed primarily of maturing collagen interspersed with CD3+/CD4-/CD8- lymphocytes in a proinflammatory microenvironment. The average ablation volumes for the canine HCC patients and the healthy porcine tissue were 3.89 cm3 ± 0.74 and 1.56 cm3 ± 0.16, respectively (P = .03), and the respective average lethal thresholds were 710 V/cm ± 28.2 and 957 V/cm ± 24.4 V/cm (P = .0004).

CONCLUSIONS

HFIRE can safely and effectively be delivered percutaneously, results in a predictable ablation volume, and is associated with lymphocytic tumor infiltration. This is the first step toward the use of HFIRE for treatment of unresectable liver tumors.

Post-treatment analysis of irreversible electroporation waveforms delivered to human pancreatic cancer patients

Irreversible electroporation (IRE) is a focal ablation therapy that uses high voltage, short electrical pulses to destroy tumor tissue. The success of treatment directly depends on exposure of the entire tumor to a lethal electric field magnitude. However, this exposure is difficult to predict ahead of time and it is challenging for clinicians to determine optimal treatment parameters. One method clinicians rely upon for the cessation of pulse delivery is to monitor the resistance value of the tissue, as the cells within the tissue will undergo changes during electroporation. This work presents a computational model which incorporates human pancreatic tumor conductivity, and compares predicted and measured output currents from IRE treatments of human patients. The measured currents vary widely from patient to patient, suggesting there may areas of high local conductivity in the treatment area.

Irreversible Electroporation: Background, Theory, and Review of Recent Developments in Clinical Oncology

Irreversible electroporation (IRE) has established a clinical niche as an alternative to thermal ablation for the eradication of unresectable tumors, particularly those near critical vascular structures. IRE has been used in over 50 independent clinical trials and has shown clinical success when used as a standalone treatment and as a single component within combinatorial treatment paradigms. Recently, many studies evaluating IRE in larger patient cohorts and alongside other novel therapies have been reported. Here, we present the basic principles of reversible electroporation and IRE followed by a review of preclinical and clinical data with a focus on tumors in three organ systems in which IRE has shown great promise: the prostate, pancreas, and liver. Finally, we discuss alternative and future developments, which will likely further advance the use of IRE in the clinic.

Temporal Characterization of Blood-Brain Barrier Disruption with High-Frequency Electroporation

Treatment of intracranial disorders suffers from the inability to accumulate therapeutic drug concentrations due to protection from the blood–brain barrier (BBB). Electroporation-based therapies have demonstrated the capability of permeating the BBB, but knowledge of the longevity of BBB disruption (BBBD) is limited. In this study, we quantify the temporal, high-frequency electroporation (HFE)-mediated BBBD in an in vivo healthy rat brain model. 40 male Fisher rats underwent HFE treatment; two blunt tipped monopolar electrodes were advanced into the brain and 200 bursts of HFE were delivered at a voltage-to-distance ratio of 600 V/cm. BBBD was verified with contrast enhanced T1W MRI (gadopentetate dimeglumine) and pathologically (Evans blue dye) at time points of 1, 24, 48, 72, and 96 h after HFE. Contrast enhanced T1W scans demonstrated BBBD for 1 to 72 h after HFE but intact BBB at 96 h. Histologically, tissue damage was restricted to electrode insertion tracks. BBBD was induced with minimal muscle contractions and minimal cell death attributed to HFE. Numerical modeling indicated that brief BBBD was induced with low magnitude electric fields, and BBBD duration increased with field strength. These data suggest the spatiotemporal characteristics of HFE-mediated BBBD may be modulated with the locally applied electric field.

Reduction of Muscle Contractions during Irreversible Electroporation Therapy Using High-Frequency Bursts of Alternating Polarity Pulses: A Laboratory Investigation in an Ex Vivo Swine Model

PURPOSE

To compare the intensity of muscle contractions in irreversible electroporation (IRE) treatments when traditional IRE and high-frequency IRE (H-FIRE) waveforms are used in combination with a single applicator and distal grounding pad (A+GP) configuration.

MATERIALS AND METHODS

An ex vivo in situ porcine model was used to compare muscle contractions induced by traditional monopolar IRE waveforms vs high-frequency bipolar IRE waveforms. Pulses with voltages between 200 and 5,000 V were investigated, and muscle contractions were recorded by using accelerometers placed on or near the applicators.

RESULTS

H-FIRE waveforms reduced the intensity of muscle contractions in comparison with traditional monopolar IRE pulses. A high-energy burst of 2-μs alternating-polarity pulses energized for 200 μs at 4,500 V produced less intense muscle contractions than traditional IRE pulses, which were 25-100 μs in duration at 3,000 V.

CONCLUSIONS

H-FIRE appears to be an effective technique to mitigate the muscle contractions associated with traditional IRE pulses. This may enable the use of voltages greater than 3,000 V necessary for the creation of large ablations in vivo.

18F-FDG PET Biomarkers Help Detect Early Metabolic Response to Irreversible Electroporation and Predict Therapeutic Outcomes in a Rat Liver Tumor Model

Purpose To test the hypothesis that biomarkers of fluorine 18 (¹⁸F) fluorodeoxyglucose (FDG) positron emission tomography (PET) can be used for the early detection of therapeutic response to irreversible electroporation (IRE) of liver tumor in a rodent liver tumor model. Materials and Methods The institutional animal care and use committee approved this study. Rats were inoculated with McA-RH7777 liver tumor cells in the left median and left lateral lobes. Tumors were allowed to grow for 7 days to reach a size typically at least 5 mm in longest diameter, as verified with magnetic resonance (MR) imaging. IRE electrodes were inserted, and eight 100-μsec, 2000-V pulses were applied to ablate the tumor tissue in the left median lobe. Tumor in the left lateral lobe served as a control in each animal. PET/computed tomography (CT) and MR imaging measurements were performed at baseline and 3 days after IRE for each animal. Additional MR imaging measurements were obtained 14 days after IRE. After 14-day follow-up MR imaging, rats were euthanized and tumors harvested for hematoxylin-eosin, CD34, and caspase-3 staining. Change in the maximum standardized uptake value (ΔSUV_max) was calculated 3 days after IRE. The maximum lesion diameter change (ΔD_max) was measured 14 days after IRE by using axial T2-weighted imaging. ΔSUV_max and ΔD_max were compared. The apoptosis index was calculated by using caspase-3-stained slices of apoptotic tumor cells. Pearson correlation coefficients were calculated to assess the relationship between ΔSUV_max at 3 days and ΔD_max (or apoptosis index) at 14 days after IRE treatment. Results ΔSUV_max, ΔD_max, and apoptosis index significantly differed between treated and untreated tumors (P < .001 for all). In treated tumors, there was a strong correlation between ΔSUV_max 3 days after IRE and ΔD_max 14 days after IRE (R = 0.66, P = .01) and between ΔSUV_max 3 days after IRE and apoptosis index 14 days after IRE (R = 0.57, P = .04). Conclusion ¹⁸F-FDG PET imaging biomarkers can be used for the early detection of therapeutic response to IRE treatment of liver tumors in a rodent model. ^© RSNA, 2017.

Physical and Chemical Enhancement of and Adaptive Resistance to Irreversible Electroporation of Pancreatic Cancer

Irreversible electroporation (IRE) can be used to treat cancer by electrical pulses, with advantages over traditional thermal approaches. Here we assess for the first time the IRE response of pancreatic cancer, one of the deadliest forms of cancer, both in vitro and in vivo. We demonstrate that both established and primary cancer cell lines can be destroyed by IRE, but with differential susceptibility and thresholds. We further demonstrate in vitro that viability for a given IRE dose can vary with the local chemistry as outcomes were shown to depend on suspending medium and reduction of glucose in the media significantly improved IRE destruction. Data here also demonstrate that repeated IRE treatments can lead to adaptive resistance in pancreatic carcinoma cells thereby reducing subsequent treatment efficacy. In addition, we demonstrate that physical enhancement of IRE, by re-arranging the pulse sequences without increasing the electrical energy delivered, achieve reduced viability in vitro and decreased tumor growth in an in vivo xenograft model. Together, these results show that IRE can destroy pancreatic cancer in vitro and in vivo, that there are both chemical and physical enhancements that can improve tumor destruction, and that one should guard against adaptive resistance when performing repeated treatments.

Predicting irreversible electroporation-induced tissue damage by means of magnetic resonance electrical impedance tomography

Irreversible electroporation (IRE) is gaining importance in routine clinical practice for nonthermal ablation of solid tumors. For its success, it is extremely important that the coverage and exposure time of the treated tumor to the electric field is within the specified range. Measurement of electric field distribution during the electroporation treatment can be achieved using magnetic resonance electrical impedance tomography (MREIT). Here, we show improved MREIT-enabled electroporation monitoring of IRE-treated tumors by predicting IRE-ablated tumor areas during IRE of mouse tumors in vivo. The in situ prediction is enabled by coupling MREIT with a corresponding Peleg-Fermi mathematical model to obtain more informative monitoring of IRE tissue ablation by providing cell death probability in the IRE-treated tumors. This technique can potentially be used in electroporation-based clinical applications, such as IRE tissue ablation and electrochemotherapy, to improve and assure the desired treatment outcome.

Treatment of Cancer In Vitro Using Radiation and High-Frequency Bursts of Submicrosecond Electrical Pulses

High-frequency irreversible electroporation (H-FIRE) is an emerging cancer therapy, which uses bursts of short duration, alternating polarity, high-voltage electrical pulses to focally ablate tumors. Here, we present a preliminary investigation of the combinatorial effects of H-FIRE and ionizing radiation. In vitro cell cultures were exposed to bursts of 500 ns pulses and single radiation doses of 2 or 20 Gy then analyzed for 14 days. H-FIRE and radiation therapy (RT) appear to induce different delayed cell death mechanisms and in all treatment groups combinatorial therapy resulted in lower overall viabilities. These results indicate that in vivo investigation of the antitumor efficacy of combined H-FIRE and RT is warranted.