Sutureless end-to-end bowel anastomosis using Nd:YAG and water-soluble intraluminal stent

CO₂ laser welding of corneal cuts with albumin solder using radiometric temperature control

PURPOSE

To examine the efficacy and reproducibility of CO₂ laser soldering of corneal cuts using real-time infrared fiber-optic radiometric control of tissue temperature in bovine eyes (in vitro) and to evaluate the duration of this procedure in rabbit eyes (in vivo).

METHODS

In vitro experiment: a 6-mm central perforating cut was induced in 40 fresh bovine eyes and sealed with a CO₂ laser, with or without albumin soldering, following placement of a single approximating nylon suture. A fiber-optic radiometric temperature control system for the CO₂ laser was used. Leaking pressure and histological findings were analyzed and compared between groups. In vivo experiment: following creation of a central perforation, 6 rabbit eyes were treated with a CO₂ laser with albumin solder and 6 rabbit eyes were treated with 10-0 nylon sutures. The amount of time needed for completion of the procedures was compared.

RESULTS

In vitro experiment: effective sealing was achieved by CO₂ laser soldering. Mean (± SD) leaking pressure was 109 ± 30 mm Hg in the bovine corneas treated by the laser with albumin solder compared to 51 ± 7 mm Hg in the sutured control eyes (n = 10 each; p < 0.001). Mean leaking pressures were much lower in the corneal cuts sealed only with the laser without albumin solder (48 ± 12 mm Hg) and in the cuts sealed only with albumin without laser welding (6.3 ± 4 mm Hg) than in the cuts treated with laser welding and albumin solder. In vivo experiment: mean surgical time was 140 ± 17 s in the laser-treated rabbits compared to 330 ± 30 s in the sutured controls (n = 6; p < 0.001). A histopathological study of the rabbit corneas 1 day after laser soldering revealed sealed corneal edges with a small gap bridged by coagulated albumin. The inflammatory reaction was minimal in contrast to the sutured controls. No thermal damage was detected at the wound edges.

CONCLUSIONS

CO₂ laser soldering combined with the fiber-optic radiometer is an effective, reliable, and rapid tool for the closure of corneal wounds, and holds advantages over conventional suturing in terms of leaking pressure and surgical time.

Laser photoirradiation in digital flexor tendon repair

This study evaluates tendon coaptation using Nd:YAG laser photoirradiation in an in vivo cockerel model. Using the intervinculum segments of the flexor profundus tendons, experimental transactions were performed. Tendon coaptation was then attempted using laser photoirradiation. Tendons were immediately examined for evidence of stable coaptation. After this assessment, specimens were excised and processed for electron microscopic examination and exposure to trypsin digestion. Despite varying multiple laser parameters, tissue welding was not observed. The subsequent functional and ultrastructural observations of irradiated tendon suggest that these changes are those of simple thermal denaturation. The results of this study suggest that when successful tissue welding has been observed in other tissue types, the mechanism is unlikely to be because of formation of intermolecular collagen bonds as hypothesized. An alternative hypothesis is that laser welding reflects photothermal coagulation of cytoplasmic peptides or nucleic acids liberated at the coaptation interface. This may explain the successful welding of cell-rich tissues such as bowel, vas deferens, and arteries and the observed failure of laser welding in collagen-rich but relatively hypocellular tendon.

Retroperitoneoscopic and laparoscopic suturing: tips and strategies for improving efficiency

BACKGROUND

The difficulties of minimally invasive reconstructive surgery, laparoscopically or retroperitoneoscopically, are caused by spatial limitation and fixed trocar positions and, therefore, restricted movement and handling of the instruments. In addition to a standardization of the technique, continual training, and improved instrument technologies, optimization of the geometry of reconstructive surgery, such as angles and distances between the working ports or the camera and needle position, are imperative to providing an optimal clinical performance.

MATERIALS AND METHODS

After designing a standardized suturing technique and conducting an experimental analysis of the geometric factors important in reconstructive surgery, we transferred these results to our clinical setting. A series of 116 reconstructive laparoscopic and retroperitoneoscopic procedures (nephropexy, pyeloplasty, bladder neck suspension, and radical prostatectomy) were analyzed according to the technical realization and quality of reconstruction. Trocar and table positions were adjusted according to our preliminary results, as were the position of the instruments and camera.

RESULTS

The trocar and instrument positions are critical for the clinical outcome of reconstructive surgery. Continual training in a standardized suturing technique, together with the clinical application of the important geometric rules, can reduce surgery time by 50%. The time required for suturing single knots could be decreased even more: as much as 75%, thus ensuring efficient and safe reconstructive surgery.

CONCLUSION

Reconstructive procedures such as pyeloplasty or radical prostatectomy can be standardized and performed in an acceptable amount of time with adequate quality when adhering to a standardized technique and the important geometric rules. Improved performance in terms of time and quality will increase the acceptance of these procedures, which can help to solve the problem associated with a low total number of indications for laparoscopy and retroperitoneoscopy.

Effects of endogenous absorption in human albumin solder for acute laser wound closure

BACKGROUND AND OBJECTIVE

Human albumin is currently being used as a biological solder in laser tissue welding. Experiments were performed to characterize the effects of differing albumin concentrations on wound closure when a 1.32 microm Nd:YAG laser is used to repair skin incisions.

MATERIALS AND METHODS

In vivo comparison of acute tensile strength was made in full thickness porcine skin wounds using different solder concentrations. Histology of the repairs was also completed to evaluate the thermal denaturation of the tissue and solder. Transmission measurements were completed for nondenatured and denatured albumin solders. Finally, the real time denaturation pattern of different solder concentrations during laser irradiation was investigated.

RESULTS

A tissue solder consisting of 50% albumin provides the greatest tensile strength for acute in vivo skin closure. The transmission measurements verify that the primary absorber of 1.32-microm laser light was the solder solvent (water). A significant decrease in power transmission occurs when the 25% albumin solder was denatured. The real time denaturation profiles demonstrate that 1.32-microm laser light denatures 25% albumin solder from the outer surface, while in 50% albumin solder, denaturation occurs from within the solder bulk. Wound histology corroborates the pattern of denaturation seen in vitro.

CONCLUSION

The combination of 1.32-microm laser light and 50% human albumin solder can be used to create a deep tissue weld resulting in higher acute repair tensile strength. This permits a deep to superficial closure of wounds, which may result in an optimal method of acute closure for full-thickness wounds.

Controlled temperature tissue fusion: argon laser welding of rat intestine in vivo. Part one

BACKGROUND AND OBJECTIVE

Thermal denaturation of proteins is recognized as a rate process governed by the local temperature-time response. Since rate processes are exponential with temperature, laser-assisted tissue welding was performed with and without temperature feedback control (TFC) to investigate the efficacy of temperature feedback in enhancing the photothermal welding process in vivo.

STUDY DESIGN/MATERIALS AND METHODS

An automated system was developed for temperature feedback controlled laser irradiation. An experimental device incorporating co-aligned laser delivery and temperature detection was used to perform argon laser welded (with and without TFC) enterotomies. The weld strength and histology of laser welded and control sutured enterotomies were compared in an in vivo rat model. Animals (n = 41) were sacrificed at 1, 3, 7, and 21 days postoperatively, and the anastomotic site was removed for bursting/leaking pressure measurements and histological examination.

RESULTS

Laser-welded (with and without TFC) and control sutured anastomoses in surviving animals healed comparably. Some laser-welded anastomoses without TFC ruptured spontaneously (4 out of 15) leading to the animals' death within the first 24-36 hours postoperatively. None of the animals in the other groups had this problem (control suture 0/6; laser with TFC 1 leak/8). The bursting/leaking pressures of the laser welded anastomoses were not significantly different than those of the sutured controls.

CONCLUSION

TFC improves the quality of laser-welded rat intestinal anastomoses in vivo in the critical first postoperative 36 hours.

Controlled temperature photothermal tissue welding

Photothermal tissue welding has been investigated as an alternative surgical tool to improve bonding of a variety of severed tissues. Yet, after almost two decades of research, inconsistencies in interpretation of experimental reports and, consequently, mechanism of this photothermal process as well as control of dosimetry remain an enigma. Widespread clinical use may greatly depend on full automation of light dosimetry to perform durable and reproducible welds with minimal thermal damage to surrounding and/or underlying tissues. Recognizing photothermal damage as a rate process, radiometrically measured tissue surface temperature has been studied as an indirect marker of tissue status during laser irradiation. Dosimetry control systems and surgical devices were developed to perform controlled temperature tissue welding using surface temperature feedback from the site of laser impact. Nevertheless, end points that mark the completion of a durable and stable weld have not been precisely identified, and subsequently, not incorporated into dosimetry control algorithms. This manuscript reviews thermal dosimetry control systems of the 1990s in an attempt to systematically indicate the difficulties encountered so far and to elaborate on major issues for photothermal tissue welding to become a clinical reality in the new millennium. © 1999 Society of Photo-Optical Instrumentation Engineers.

Carbon dioxide laser tissue welding: an alternative technique for tubal anastomosis?

Microsurgical tubal anastomosis is the gold standard for treatment of tubal occlusion. The present study was performed to establish the feasibility of tubal anastomosis by welding tissue with a defocused CO2-laser beam during laparotomy and with an endoscope. In an animal experiment, 70 white New Zealand rabbits were randomized in 2 study groups (E1, E2) and 3 control groups (C1, C2, C3) as follows: C1, 10 animals, no operation, as controls for the efficiency of the insemination technique; C2, 5 animals, spontaneous healing after tubal segment resection, to quantify spontaneous recanalization of the tube; C3, 15 animals, microsurgical end-to-end adaption after tubal segment resection; E1, 20 animals, laser welded anastomosis after segment resection via laparotomy; E2, 20 animals, laparoscopic laser welded anastomosis after segment resection. The pregnancy rate in C1 was 80%. None of the animals in C2 but 60% of the rabbits in C3 conceived. After sutureless anastomosis by laser welding 50% of the laparotomized, and 40% of the laparoscopically operated group became pregnant. Morphological examination of the oviducts after relaparotomy showed comparable patency rates of 70% in C3, 70% in E1, and 65% in E2. Whereas no dehiscence of anastomoses was observed in C3, 20% of the welded tubes in E1 and 22.5% in E2 were dehiscent. Tubal anastomosis took approximately three times as long laparoscopically as during laparotomy. Thus, laser welding as a sutureless alternative technique of tubal anastomosis should be viewed critically. A reduction of sutures through laser-assisted anastomosis might, however, be considered.

Temperature-controlled CO2 laser tissue welding of ocular tissues

Lasers can be used for binding tissues by welding, but the clinical application of this method has been limited by the difficulties in defining and maintaining the optimal conditions. Fiberoptic radiometry allows accurate remote temperature measurements for control of laser tissue welding. We evaluated the use of a temperature-controlled tissue welding system to close corneal and corneoscleral wounds. Eighty ex vivo bovine eyes were used for the determination of welding parameters optimal for corneal wound closure. A 4 mm central corneal cut was closed with use of a CO2 laser (600 mw, 0.9 mm spot size), with tissue temperatures ranging from 45-70 degrees C and welding time ranging from 1-30 seconds. Wound strength was measured as burst pressure of the sealed wound. The welding parameters found to cause the strongest wound binding were used to weld a limbal incision of 4 mm in 10 adult albino rabbits. The fellow eye of each animal was used as a control, and the same wound was closed with one 10/0 mersilen suture. Two animals were killed immediately after the procedure, and the eyes were sent for histologic examination. Eight rabbits were followed for 1 month. Clinical examination and refraction were done 1 day, 1 week, 2 weeks, and 1 month after the procedure. Corneal topographic evaluations were done 1 week after the procedure. After 1 month the animals were killed and the eyes were examined histologically. The optimal results of wound binding by laser welding in the enucleated bovine eyes were achieved with 55-60 degrees C and at a welding time of 12-20 seconds. At these parameters the burst pressure of corneal wounds was 70 mm Hg. All laser-welded limbal wounds in the rabbits were tightly closed at the end of procedure and during the follow-up period. The refractive results after laser welding were equal to those of the controlled suture-closed wound. Laser tissue welding combined with tissue temperature monitoring can be used to close corneal wounds.

Experimental oesophagogastric anastomosis: preliminary report of a new compression device that also fragments

Fifteen Beagle dogs underwent oesophagogastric anastomosis with a new device which enables a 'sutureless' compression anastomosis. The device fragmented and was passed in bits anally without causing obstruction. Immediate bursting pressure, tested in five dogs, was between 175 and 190 mmHg. The anastomoses of the remaining dogs were examined macroscopically and microscopically from day 6 to day 30. Healing was excellent with good muscular apposition and minimal residual inflammation.

First experimental sutureless laser anastomosis of the large bowel: long-term study

Large bowel anastomoses were successfully performed without sutures on New Zealand white rabbits using 1,064 nm, 0.4-W power pulsating Nd:YAG laser to create tissue welding.

PURPOSE

The aim of this study was to assess long-term results of our experimental data and summarize our experimental work on laser colon anastomosis.

METHODS

This experimental study investigated long-term integrity, degree of narrowing, animal body weight change, visual findings, microscopic appearance, and collagen concentration of laser colon anastomoses, compared with those of conventional sutured anastomoses at thirty and ninety postoperative days.

RESULTS

Two animals in the laser group died without leakage. Postsurgical course in all remaining rabbits studied was uneventful. Bursting pressures in the two groups were equivalent, but the laser group exhibited a consistent narrowing tendency. However, laser anastomoses demonstrated fewer and milder adhesions, and animals showed a better recovery of body weight. Histologically, laser anastomoses showed better layer-to-layer reconstitution without foreign body response and with less fibrosis. Difference in collagen (hydroxyproline) concentration did not reach statistical significance.

CONCLUSION

The nature of tissue welding via laser remains undefined, but there is definitely a future for laser bowel anastomosis.

Controlled temperature tissue fusion: argon laser welding of canine intestine in vitro

BACKGROUND AND OBJECTIVE

Thermal denaturation of proteins is recognized as a rate process governed by the local temperature-time response and is believed to be the principal mechanism for photothermal tissue welding. Since rate processes are exponential with temperature, feedback control of tissue surface temperature is hypothesized to create a quasi-constant rate of denaturation that will enhance the tissue welding process.

STUDY DESIGN, MATERIALS AND METHODS

Controlled temperature tissue welding of severed edges of fresh canine jejunum was performed in vitro by remote sensing of tissue surface temperature with an infrared sensor. A hardware controlled temperature feedback system opened and closed a shutter located in the beam path of an argon ion laser to provide constant temperature welding.

RESULTS

Strong tissue fusion was not possible at or below a surface temperature of 70 degrees C, but was accomplished at 80 degrees, 90 degrees, and 95 degrees, and 100 degrees C. Fusion was achieved with thermal coagulation of the collagenous submucosa and mucosal tissues. The bursting strength of welds created at 90 degrees C and 95 degrees C were significantly stronger than those performed at 80 degrees C.

CONCLUSION

Laser-assisted intestinal anastomoses created in vitro are optimally strong at 90-95 degrees C feedback control temperatures.

Prevention of pharyngocutaneous fistulas by means of laser-weld techniques

Although much has been written on methods of dealing with pharyngocutaneous fistulas once they have formed, there are few reports of methods of preventing fistula formation from occurring. We examined the use of laser-weld techniques with the neodymium:yttrium aluminum garnet (Nd:YAG) and diode lasers to seal pharyngotomy closures. Laser-weld techniques have been used successfully in many other tissues, but reports documenting use in the upper aerodigestive tract are minimal. Indocyanine-green dye-enhanced collagen and fibrinogen were studied as laser solder materials for the diode laser. Twenty-nine experimental animals were studied. Neither the Nd:YAG nor the diode laser was successful in preventing fistula formation. Tensiometric studies documented significant strength of the laser welds ex vivo, but this finding was not clinically significant.

Experimental laser anastomosis of the colon. Long-term results and histologic findings after laser closure of colotomies

PURPOSE

Our previous experimental work showed the feasibility of colon anastomosis using laser; however, it also revealed a narrowing tendency after laser anastomosis. Long-term observation of the postoperative course of laser anastomosis was planned to assess this point.

METHODS

Clinical observation and histologic examination of transverse colotomies (average, 21.2 mm) in New Zealand white rabbits (n = 12) closed with a 1,064-nm neodymiumyttrium aluminum garnet (Nd:YAG) laser were carried out up to the third postoperative month, compared with closure of colotomies using a single layer of interrupted sutures of 5-0 Maxon (Davis & Geck, Pearl River, NY) in a control group (n = 12).

RESULTS

Whereas the narrowing tendency was observed up to one month after the operation in the laser group (P < 0.05), it disappeared at three months following the operation without causing abnormal weight loss during the experiment. Simultaneously, there was again a marked decrease in adhesion formation following laser anastomosis (P < 0.01). Collagen fibers were observed earlier in the laser group.

CONCLUSIONS

An earlier commencement of collagen synthesis after laser anastomosis was proved. A narrowing tendency, which was observed from seven days to one month postoperatively, disappeared at three months after laser anastomosis without exerting any effect on growth.

Silver halide fiber optic radiometric temperature measurement and control of CO2 laser-irradiated tissues and application to tissue welding

Tissue heating by laser irradiation has attained importance in many clinical applications. Accurate temperature measurements of laser-irradiated tissues are difficult to achieve, and experiments have produced conflicting results. Fiber optic radiometry allows temperature measurement of laser-irradiated tissues by remote sensing of the emitted infra red (IR) radiation. We have developed an IR fiber optic radiometer capable of accurate tissue temperature measurements (+/- 0.2 degrees C) and utilized it to monitor and control the heating of tissues by CO2 laser irradiation. Tissue temperature control of +/- 2.5 degrees C was achieved. This system was used to control tissue temperature during CO2 laser-assisted welding of urinary bladders in rats. The strength of the welds was recorded for different welding temperatures. A temperature of 55 degrees C was found to be optimal.

Cellular proliferation at sutured and sutureless colonic anastomoses

Elevated cellular proliferation in the vicinity of an anastomosis may explain the enhanced susceptibility to carcinogens. The aim of this study was to determine whether anastomotic cellular proliferation was altered by different suture materials and whether a rise in cell turnover also occurred after a "sutureless" closure. A transverse descending colon enterotomy was repaired with interrupted sutures of 5/0 silk (n = 20), stainless steel (n = 20), or Vicryl (Ethicon, Inc., Somerville, NJ) (n = 20) or by a sutureless technique (n = 20). Using a stathmokinetic technique, crypt cell production rates (CCPR) were calculated at the anastomosis and in the adjacent colon at varying intervals between one week and six months after treatment. Overall colonic cellular proliferation appeared to be elevated at a sutured colotomy for at least three months (P < 0.05). In contrast, no significant elevation in cellular proliferation was observed at sutureless anastomoses. The duration of elevated proliferative response varied among the sutures.

Experimental carcinogenesis at sutured and sutureless colonic anastomoses

This study explores the role of sutures and the healing colonic wound in experimental carcinogenesis. One hundred sixty rats underwent surgery with colotomy and repair using silk, steel, or Vicryl (Ethicon, Somerville, NJ) sutures or a sutureless technique. Forty rats had a sham procedure. All animals received azoxymethane for 12 weeks at a dose of 10 mg/kg/week. Half the rats commenced carcinogen before surgery, and half commenced it eight weeks after surgery. Animals with anastomotic tumors were found in 46 percent of the sham group (P less than 0.05 cf. sutured), 41 percent of the sutureless group (P less than 0.02 cf. sutured), and 68 percent of the sutured group. The corresponding figures for anastomotic carcinoma were 9 percent (P less than 0.001 cf. sutured), 22 percent, and 38 percent. No significant differences in tumor yield were noted among the different sutures. However, several differences were noted between the two carcinogen models. In those animals that received surgery first, there was a higher incidence of anastomotic tumors (P less than 0.002) and cancers (P less than 0.0001) in the sutured and sutureless groups, and those tumors that occurred in the sutured group were considerably larger than in those that had carcinogen first (15.9 mm cf. 4.9 mm; P less than 0.0001). Overall, all sutures seem to enhance anastomotic tumor formation, and we would suggest that a sutureless anastomosis may diminish this risk.

First experimental sutureless end-to-end laser anastomosis of the large bowel. Short-term results

Completely sutureless end-to-end large bowel anastomoses were successfully created in New Zealand white rabbits (n = 26) by using a low-energy (0.4-W wave of power) Nd:YAG laser to produce welded anastomoses. In this study, the short-term integrity, degree of narrowing, macroscopic appearance, and microscopic findings were compared with those of the conventional interrupted one-layer anastomosis (n = 24) at zero, one, four, and seven days after surgery. Two rabbits in the laser group died from leakage. All remaining animals had an uneventful postoperative course. The bursting pressures in the laser group at zero, one, and four days were lower than those in the control group. The narrowing index of the laser anastomosis was higher than that of the suture anastomosis at four and seven days. However, the laser anastomoses showed fewer adhesions, no instances of bowel obstruction, and histologic healing with less fibrosis. The technique of laser anastomosis presents a promising alternative to suturing in reconstitution of the large bowel.

First sutureless closure of a colotomy: short-term results of experimental laser anastomosis of the colon

To assess the possibility of laser anastomosis of the colon, experimental laser closure of colotomies was performed. Transverse colotomies (average 20.7 mm) in New Zealand white rabbits (n = 20) were closed with a 1,064-nm Nd:YAG laser at a pulsating 0.5-W wave of power, using guy sutures to approximate the tissue edges. The laser energy was applied through a specially designed hand piece and hand-held 600-microns gas-cooled noncontact quartz fiber to produce a satisfactory tissue welding. Similar colotomies were closed using a single layer of interrupted sutures of 5-0 Maxon (Davis & Geck, Pearl River, NY) in a control group (n = 20). Bursting pressure and index of narrowing were recorded immediately after anastomosis and at 1, 4, and 7 days following surgery. Bursting pressure of the laser-welded closure at 1 day was significantly lower than that of the sutured controls (P less than 0.01); however, all rabbits recovered uneventfully. There was a marked decrease in adhesion formation following laser anastomosis (P less than 0.05). Conversely, one control rabbit showed functional stenosis at 4 days. Histologic study revealed an accelerated healing in the laser group. The index of narrowing was significantly higher in the laser group than in the control group (P less than 0.05). The completely water-sealed laser anastomosis reduces adhesions and is comparable to conventional suture anastomosis of the colon.

Sutureless intestinal anastomoses

Sutureless intestinal anastomoses can be achieved either by compression, where two inverted rings of bowel are compressed by a hollow circular device that subsequently sloughs away and is passed anally, or by the use of tissue glues or laser welding. Compression devices used clinically with success are the Valtrac biofragmentable anastomotic ring, the polypropylene rings described by Rosati and the AKA guns. Glued anastomoses have only been used in animals and seem to be unsafe. However, laser-welded intestinal anastomoses appear highly promising in experimental studies and further development of this technique is warranted.