A Versatile Strategy to Synthesize Perfluoropolyether-Based Thermoplastic Fluoropolymers by Alkyne-Azide Step-Growth Polymerization

Fabrication of a High Proton-Conducting Sulfonated Fe-Metal Organic Framework-Polytriazole Composite Membranes: Study of Proton Exchange Membrane Properties

A series of hybrid composite membranes including polymer-metal-organic frameworks (MOFs), are synthesized using sulfonated Fe-MOF and sulfonated polytriazole (PTSF). After being post-modified by 1,3-propane sultone, the obtained Fe-S MOF is incorporated into the polytriazole polymer matrix through the solution blending method. Additionally, a series of polytriazole with a degree of sulfonation of 60 is prepared, with the percentage of the Fe-S MOF ranging from 3 to 9 weight percent. A comparison is made between the properties of these hybrid membranes and those of the pristine membranes. The hybrid membranes demonstrate a high degree of solubility in every solvent that is employed. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) confirm that the MOF is distributed uniformly throughout the polymer matrix. Moreover, well-separated morphologies are confirmed by transmission electron microscopy (TEM). The prepared hybrid membranes demonstrate enhanced proton conductivities, water absorption, and swelling, all of which are accomplished without influencing the oxidative stability values.

Polysiloxane-Based Liquid-like Layers for Reducing Polymer and Wax Fouling

Surface fouling occurs when undesired matter adheres and accumulates on a surface, resulting in a decrease or loss of functionality. Polymer and wax fouling can cause costly blockages to crude oil pipelines, clog jet fuel injectors, foul chemical reaction vessels, and significantly decrease the efficiency of heat exchangers. Fouling occurs in many forms but can be segmented based on adherent size, modulus, and chemical functionality. Depending on the foulant, surface design strategies can vary greatly. Few strategies exist to prevent the buildup of wax and polymers on surfaces. In this report, we investigate the potential of highly disordered, siloxane liquid-like layers as a strategy for reducing wax and polymer deposition. In our tests, it was found that the liquid-like layers developed here were able to reduce postadsorption roughness for polymer and wax by as much as 35- and 47-fold, respectively, when compared to the control. SFG was utilized to investigate the molecular-level interfacial properties for each of the modified surfaces to help understand the antifouling mechanism. The data showed that the likely higher grafting density and a large degree of random conformational freedom at the liquid-surface interface make the developed siloxane-covered surfaces energetically unfavorable for polymer and wax accretion.

Mesoscale Modeling of Agglomeration of Molecular Bottlebrushes: Focus on Conformations and Clustering Criteria

Using dissipative particle dynamics, we characterize dynamics of aggregation of molecular bottlebrushes in solvents of various qualities by tracking the number of clusters, the size of the largest cluster, and an average aggregation number. We focus on a low volume fraction of bottlebrushes in a range of solvents and probe three different cutoff criteria to identify bottlebrushes belonging to the same cluster. We demonstrate that the cutoff criteria which depend on both the coordination number and the length of the side chain allows one to correlate the agglomeration status with the structural characteristics of bottlebrushes in solvents of various qualities. We characterize conformational changes of the bottlebrush within the agglomerates with respect to those of an isolated bottlebrush in the same solvents. The characterization of bottlebrush conformations within the agglomerates is an important step in understanding the relationship between the bottlebrush architecture and material properties. An analysis of three distinct cutoff criteria to identify bottlebrushes belonging to the same cluster introduces a framework to identify both short-lived transient and long-lived agglomerates; the same approach could be further extended to characterize agglomerates of various macromolecules with complex architectures beyond the specific bottlebrush architecture considered herein.

Novel perfluoropolyalkylethers monomers: synthesis and photo-induced cationic polymerization

Several difunctional oligomers were synthesized by functionalizing perfluoropolyalkylether (PFPAE) chains with different vinyl ethers and epoxides end-groups. Due to their innate synthetic challenges and demanding purification protocols, the PFPAE derivatives were obtained in low yield and with an average functionality lower than 2. However, the functionalized PFPAE oligomers were successful in being used in photo-induced cationic polymerization processes, obtaining transparent and soft films. The influences of the fluorinated chains, and various end-groups on the photopolymerization process were investigated, as well their chemical stability, thermal degradation, and surface properties.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s00396-021-04838-1.

Towards a Long-Chain Perfluoroalkyl Replacement: Water and Oil Repellent Perfluoropolyether-Based Polyurethane Oligomers

Original perfluoropolyether (PFPE)-based oligomeric polyurethanes (FOPUs) with different macromolecular architecture were synthesized (in one step) as low-surface-energy materials. It is demonstrated that the oligomers, especially the ones terminated with CF₃ moieties, can be employed as safer replacements to long-chain perfluoroalkyl substances/additives. The FOPU macromolecules, when added to an engineering thermoplastic (polyethylene terephthalate, PET) film, readily migrate to the film surface and bring significant water and oil repellency to the thermoplastic boundary. The best performing FOPU/PET films have reached the level of oil wettability and surface energy significantly lower than that of polytetrafluoroethylene, a fully perfluorinated polymer. Specifically, the highest level of the repellency is observed with an oligomeric additive, which was made using aromatic diisocyanate as a comonomer and has CF₃ end-group. This semicrystalline oligomer has a glass transition temperature (T_g) well above room temperature, and we associate the superiority of the material in achieving low water and oil wettability with its ability to effectively retain CF₃ and CF₂ moieties in contact with the test wetting liquids.

Perfluoropolyether-benzophenone as a highly durable, broadband anti-reflection, and anti-contamination coating

Anti-reflection and anti-contamination coatings prepared from fluorinated polymers have widespread and important applications, ranging from protective films for corrosion resistance to high-tech microelectronics and medical devices due to their transparency, low refractive index, stain resistance, and antifouling properties. However, the application of existing coatings is hindered by low surface adhesion to the target substrate and weakness when exposed to mechanical stress or damage, resulting in significant limitations to their practical applications. Herein, we incorporate perfluoropolyether (PFPE) with benzophenone (BP) to develop an efficient coating material (PFPE-BP) possessing broadband anti-reflectivity, anti-contamination properties, excellent abrasion resistance, and stability under elevated temperatures and relative humidity. The presence of BP allows the coating materials to be homogeneously mixed with a commercial hard coating solution to uniformly coat the target substrate. Furthermore, UV light irradiation on the coating surface results in excellent adhesion between BP groups of PFPE-BP and the hard coating matrix.

Attainment of Water and Oil Repellency for Engineering Thermoplastics without Long-Chain Perfluoroalkyls: Perfluoropolyether-Based Triblock Polyester Additives

For decades, water and oil repellency of engineering thermoplastics has been achieved with introduction of long-chain perfluoroalkyl substances and moieties (C _nF_{2 n+1}, n ≥ 7). However, their bioaccumulative and toxicological impact is now widely recognized and, consequently, the substances have been phased out of industrial production and applications. To this end, we have synthesized fluorinated oligomeric triblock polyesters (FOPBs), which do not possess the long-chain perfluoroalkyl segments and serve as effective low-surface-energy additives to engineering thermoplastics. More specifically, we obtained original perfluoropolyether (PFPE)-based triblock copolymers, in which two identical fluorinated blocks were separated by a short nonfluorinated polyester block made of poly(ethylene isophthalate) (PEI). It was found that when FOPBs were added to poly(ethylene terephthalate), nylon-6, and poly(methyl methacrylate) films they readily migrate to the film surface and in doing so imparted significant water and oil repellency to the thermoplastic boundary. The water/oil wettability of the films modified with FOPB is considerably lower than the wettability of the films modified with an analogous PFPE-based polyester, which differs from FOPB only by the absence of the short nonfluorinated PEI middle block. We associate the superiority of the triblock copolymers in terms of water and oil repellency with their ability to form brushlike structures on polymer film surfaces.

Synthesis and Characterization of Highly Proton Conducting Sulfonated Polytriazoles

This article describes the synthesis and characterization of highly sulfonated polytriazole copolymers (PTSQSH-I to IV) with IEC_w values ranging from 2.41 to 3.49 mequiv g^-1. The copolymers were synthesized by click reaction between equimolar amount of a dialkyne monomer, potassium 2,5-bis(2-propyn-1-yloxy)benzenesulfonate, and a mixture of two different diazide monomers, 4,4-bis[3'-trifluoromethyl-4'(4-azidobenzoxy)benzyl]biphenyl and 4,4'-diazido-2,2'-stilbene disulfonic acid disodium salt. The copolymers were characterized by Fourier transform infrared and NMR spectroscopy techniques. The membranes were prepared by dissolving the salt form of the copolymers in dimethyl sulfoxide. The copolymers showed high thermal, mechanical, and oxidative stabilities, and the acidified membranes showed very high proton conductivity (43-173 and 132-304 mS cm^-1 at 30 and 80 °C, respectively). Transmission electron microscopy images confirmed the formation of well-phase-separated morphology with interconnected hydrophilic domains (20-150 nm).

Light-Induced Step-Growth Polymerization of AB-Type Photo-Monomers at Ambient Temperature

We introduce two AB-type monomers able to undergo a facile catalyst-free photoinduced polycycloaddition of photocaged dienes, enabling rapid Diels-Alder ligations under UV-irradiation (λ_max = 350 nm) at ambient temperature, closely adhering to Carother's equation established by a careful kinetic study (17800 g mol^-1 < M_w < 24700 g mol^-1). The resulting macromolecules were in-depth analyzed via size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. Additionally, SEC hyphenated to high resolution-electrospray ionization-mass spectrometry (HR-ESI-MS) enabled the careful mapping of the end group structure of the generated polymers. Furthermore, we demonstrate that both monomer systems can be readily copolymerized. The study thus demonstrates that Diels-Alder ligation resting upon photocaged dienes is a powerful tool for accessing step-growth polymers.

Toward a Long-Chain Perfluoroalkyl Replacement: Water and Oil Repellency of Polyethylene Terephthalate (PET) Films Modified with Perfluoropolyether-Based Polyesters

Original perfluoropolyethers (PFPE)-based oligomeric polyesters (FOPs) of different macromolecular architecture were synthesized via polycondensation as low surface energy additives to engineering thermoplastics. The oligomers do not contain long-chain perfluoroalkyl segments, which are known to yield environmentally unsafe perfluoroalkyl carboxylic acids. To improve the compatibility of the materials with polyethylene terephthalate (PET) we introduced isophthalate segments into the polyesters and targeted the synthesis of lower molecular weight oligomeric macromolecules. The surface properties such as morphology, composition, and wettability of PET/FOP films fabricated from solution were investigated using atomic force microscopy, X-ray photoelectron spectroscopy, and contact angle measurements. It was demonstrated that FOPs, when added to PET film, readily migrate to the film surface and bring significant water and oil repellency to the thermoplastic boundary. We have established that the wettability of PET/FOP films depends on three main parameters: (i) end-groups of fluorinated polyesters, (ii) the concentration of fluorinated polyesters in the films, and (iii) equilibration via annealing. The most effective water/oil repellency FOP has two C₄F₉-PFPE-tails. The addition of this oligomeric polyester to PET allows (even at relatively low concentrations) reaching a level of oil repellency and surface energy comparable to that of polytetrafluorethylene (PTFE/Teflon). Therefore, the materials can be considered suitable replacements for additives containing long-chain perfluoroalkyl substances.

Sequence-Controlled Glycopolymers via Step-Growth Polymerization of Precision Glycomacromolecules for Lectin Receptor Clustering

A versatile approach for the synthesis of sequence-controlled multiblock copolymers, using a combination of solid phase synthesis and step-growth polymerization by photoinduced thiol-ene coupling (TEC) is presented. Following this strategy, a series of sequence-controlled glycopolymers is derived from the polymerization of a hydrophilic spacer macromonomer and different glycomacromonomers bearing between one to five α-d-Mannose (Man) ligands. Through the solid phase assembly of the macromonomers, the number and positioning of spacer and sugar moieties is controlled and translates into the sequence-control of the final polymer. A maximum M̅_n of 16 kDa, corresponding to a X̅_n of 10, for the applied macromonomers is accessible with optimized polymerization conditions. The binding behavior of the resulting multiblock glycopolymers toward the model lectin Concanavalin A (ConA) is studied via turbidity assays and surface plasmon resonance (SPR) measurements, comparing the ability of precision glycomacromolecules and glycopolymers to bind to and cross-link ConA in dependence of the number of sugar moieties and overall molecular weight. The results show that there is a clear correlation between number of Man ligands and Con A binding and clustering, whereas the length of the glycooligomer- or polymer backbone seems to have no effect.

Kinetic and mechanistic aspects of the iodine transfer copolymerization of vinylidene fluoride with 2,3,3,3-tetrafluoro-1-propene and functionalization into ω-hydroxy fluorinated copolymers

ω-Hydroxy functionalized poly(vinylidene fluoride) prepared in a water-based non-fluorinated solvent by iodine transfer copolymerization VDF and 1234yf.