Isothermal Crystallization Kinetics Study of Fully Aliphatic PA6 Copolyamides: Effect of Novel Long-Chain Polyamide Salt as a Comonomer

N¹, N⁶-bis (4-aminobutyl) adipamide (BABA) diamine and sebacic acid (SA), also called BABA/SA polyamide salt, were used in a typical melt polymerization processes of polyamide 6 (PA6) to form a series of PA6-BABA/SA copolyamides. The effects of BABA/SA on the isothermal crystallization kinetics of PA6-BABA/SA were studied for the first time. An isothermal crystallization analysis demonstrates that the PA6-BABA/SA matrix provided a higher crystallization rate and shorter half-crystallization time than virgin PA6 did. The degree of crystallization of the PA6-BABA/SA₃₀ matrix was also the lowest among all of the samples considered herein. This result is attributed to the high nucleation efficacy of a small amount of BABA/SA in the crystallization of PA6. Values of the Avrami exponent (n) from 1.84 to 3.91 were observed for all of the polyamide samples, suggesting that the crystallization was involved via a two- to three-dimensional growth mechanism. These findings deepen our understanding of the structure–property relationship of PA6-BABA/SA copolyamides, favoring their practical application.

Effect of Multiwalled Carbon Nanotubes on the Mechanical Properties of Carbon Fiber-Reinforced Polyamide-6/Polypropylene Composites for Lightweight Automotive Parts

The development of lightweight automotive parts is an important issue for improving the efficiency of vehicles. Polymer composites have been widely applied to reduce weight and improve mechanical properties by mixing polymers with carbon fibers, glass fibers, and carbon nanotubes. Polypropylene (PP) has been added to carbon fiber-reinforced nylon-6 (CF/PA6) composite to achieve further weight reduction and water resistance. However, the mechanical properties were reduced by the addition of PP. In this research, multiwalled carbon nanotubes (CNTs) were added to compensate for the reduced mechanical properties experienced when adding PP. Tensile testing and bending tests were carried out to evaluate the mechanical properties. A small amount of CNTs improved the mechanical properties of carbon fiber-reinforced PA6/PP composites. For example, the density of CF/PA6 was reduced from 1.214 to 1.131 g/cm³ (6.8%) by adding 30 wt % PP, and the tensile strength of 30 wt % PP composite was improved from 168 to 173 MPa (3.0%) by adding 0.5 wt % CNTs with small increase of density (1.135 g/cm³). The developed composite will be widely used for lightweight automotive parts with improved mechanical properties.

Structure–property relationships in super-toughened polypropylene-based ternary blends of core–shell morphology

A specific “percolated/interconnected” morphology of PA6/EPDM-g-MA core–shell modifier particles in PP matrix resulted in a tremendous enhancement of impact strength. Fracture behavior and toughening mechanisms were studied and proposed.

Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR FT-IR) Mapping Coupled with Multivariate Curve Resolution (MCR) for Studying the Miscibility of Chlorobutyl Rubber/Polyamide-12 Blends

A series of chlorobutyl rubber/polyamide-12 (CIIR/PA-12) blends compatibilized by different amounts of maleic anhydride (MAH) grafted polypropylene (PP-g-MAH) were investigated by attenuated total reflection Fourier transform infrared spectroscopy (ATR FT-IR) mapping. Multivariate curve resolution (MCR) was used to process the FT-IR images. Both the spectra of pure components in the blends and their concentration distributions in a micro-region were acquired. Our results demonstrated that the blend with 15 parts per hundred rubber PP-g-MAH showed the best miscibility. An amide interphase and an imide interphase were inferred by analyzing the spectra of MCR component 3 of the blends with and without PP-g-MAH, respectively. Correspondingly, two different compatibilizing mechanisms were proposed for these blends.

Morphology development of PP/POE blends with high loading of magnesium hydroxide

A co-continuous structure of PP/POE was maintained even after a large amount of Mg(OH)₂ was added, which was the key factor for tolerating high loading of additives and retaining acceptable tensile properties.