Preparation of PCL Electrospun Fibers Loaded with Cisplatin and Their Potential Application for the Treatment of Prostate Cancer

Prostate cancer is a global fatal type of cancer. It is a type of cancer that affect men. Signs and symptoms of the disease include blood in the urine, pain when one micturates, and difficulties in penis erection. Cisplatin chemotherapy is a principal treatment normally given to the prostate cancer patients. Nonetheless, on its own, cisplatin loses efficacy once administered due to liver pass effects and other biochemical attacks. In this paper, we looked at preparation of PCL nanoparticles loaded with cisplatin and their potential for the treatment of prostate cancer. PCL nanoparticles protect cisplatin from biochemical attack, thus increasing drug efficacy. Incorporation of P-glycoprotein inhibitors in PCL nanoparticles (NPs) loaded with cisplatin could improve prostate cancer treatment even more.

Enhanced Li-Ion Rate Capability and Stable Efficiency Enabled by MoSe2 Nanosheets in Polymer-Derived Silicon Oxycarbide Fiber Electrodes

Transition metal dichalcogenides (TMDs) such as MoSe2 have continued to generate interest in the engineering community because of their unique layered morphology-the strong in-plane chemical bonding between transition metal atoms sandwiched between two chalcogen atoms and the weak physical attraction between adjacent TMD layers provides them with not only chemical versatility but also a range of electronic, optical, and chemical properties that can be unlocked upon exfoliation into individual TMD layers. Such a layered morphology is particularly suitable for ion intercalation as well as for conversion chemistry with alkali metal ions for electrochemical energy storage applications. Nonetheless, host of issues including fast capacity decay arising due to volume changes and from TMD's degradation reaction with electrolyte at low discharge potentials have restricted use in commercial batteries. One approach to overcome barriers associated with TMDs' chemical stability functionalization of TMD surfaces by chemically robust precursor-derived ceramics or PDC materials, such as silicon oxycarbide (SiOC). SiOC-functionalized TMDs have shown to curb capacity degradation in TMD and improve long term cycling as Li-ion battery (LIBs) electrodes. Herein, we report synthesis of such a composite in which MoSe2 nanosheets are in SiOC matrix in a self-standing fiber mat configuration. This was achieved via electrospinning of TMD nanosheets suspended in pre-ceramic polymer followed by high temperature pyrolysis. Morphology and chemical composition of synthesized material was established by use of electron microscopy and spectroscopic technique. When tested as LIB electrode, the SiOC/MoSe2 fiber mats showed improved cycling stability over neat MoSe2 and neat SiOC electrodes. The freestanding composite electrode delivered a high charge capacity of 586 mAh g-1electrode with an initial coulombic efficiency of 58%. The composite electrode also showed good cycling stability over SiOC fiber mat electrode for over 100 cycles.

New Strategies for Safe Cancer Therapy Using Electrospun Nanofibers: A Short Review

Electrospun nanofibers regarding their special features, including high drug loading capacity, high surface to volume area, flexibility, and ease of production and operation, are of great interest for being used in tissue engineering, and drug delivery approaches. In this context, several studies have been done for the production of biodegradable and biocompatible scaffolds containing different anticancer agents for fighting with solid tumors. Surprisingly, these scaffolds are able to deliver different combinations of drugs and agents, such as nanoparticles and release them in a time dependent manner. Here in this review, we summarize the principles of electrospinning and their uses in entrapment of drugs and anti-proliferative agents suitable for cancer therapy. The latest studies performed on treating cancer using electrospinning are mentioned and their advantages and disadvantages over conventional treatment methods are discussed.

Electrospun Nanofibrous Scaffolds: Review of Current Progress in the Properties and Manufacturing Process, and Possible Applications for COVID-19

Over the last twenty years, researchers have focused on the potential applications of electrospinning, especially its scalability and versatility. Specifically, electrospun nanofiber scaffolds are considered an emergent technology and a promising approach that can be applied to biosensing, drug delivery, soft and hard tissue repair and regeneration, and wound healing. Several parameters control the functional scaffolds, such as fiber geometrical characteristics and alignment, architecture, etc. As it is based on nanotechnology, the concept of this approach has shown a strong evolution in terms of the forms of the materials used (aerogels, microspheres, etc.), the incorporated microorganisms used to treat diseases (cells, proteins, nuclei acids, etc.), and the manufacturing process in relation to the control of adhesion, proliferation, and differentiation of the mimetic nanofibers. However, several difficulties are still considered as huge challenges for scientists to overcome in relation to scaffolds design and properties (hydrophilicity, biodegradability, and biocompatibility) but also in relation to transferring biological nanofibers products into practical industrial use by way of a highly efficient bio-solution. In this article, the authors review current progress in the materials and processes used by the electrospinning technique to develop novel fibrous scaffolds with suitable design and that more closely mimic structure. A specific interest will be given to the use of this approach as an emergent technology for the treatment of bacteria and viruses such as COVID-19.

Self-supporting carbon-rich SiOC ceramic electrodes for lithium-ion batteries and aqueous supercapacitors

Fabrication of precursor-derived ceramic fibers as electrodes for energy storage applications remains largely unexplored. Within this work, three little known polymer-derived ceramic (PDC)-based fibers are being studied systemically as potential high-capacity electrode materials for electrochemical energy devices. We report fabrication of precursor-derived SiOC fibermats via one-step spinning from various compositions of siloxane oligomers followed by stabilization and pyrolysis at 800 °C. Electron microscopy, Raman, FTIR, XPS, and NMR spectroscopies reveal transformation from polymer to ceramic stages of the various SiOC ceramic fibers. The ceramic samples are a few microns in diameter with a free carbon phase embedded in the amorphous Si–O–C structure. The free carbon phase improves the electronic conductivity and provides major sites for ion storage, whereas the Si–O–C structure contributes to high efficiency. The self-standing electrodes in lithium-ion battery half-cells deliver a charge capacity of 866 mA h g_electrode⁻¹ with a high initial coulombic efficiency of 72%. As supercapacitor electrode, SiOC fibers maintain 100% capacitance over 5000 cycles at a current density of 3 A g⁻¹.

Fabrication of precursor-derived ceramic fibers as electrodes for energy storage applications remains largely unexplored.

Progress in the use of electrospun nanofiber electrodes for solid oxide fuel cells: a review

The application of one-dimensional nanofibers in the fabrication of an electrode greatly improves the performance of solid oxide fuel cells (SOFCs) due to its advantages on electron transfer and mass transport. Various mixed ionic-electronic conducting materials with perovskites and Ruddlesden-Popper-type metal oxide structures are successfully electrospun into nanofibers in recent years mostly in solvent solution and some in melt forms, which are used as anode and cathode electrodes for SOFCs. This paper presents a comprehensive review of the structure, electrochemical performance, and development of anode and cathode nanofiber electrodes including processing, structure, and property characterization. The focuses are first on the precursor, applied voltage, and polymer in the material electrospinning process, the performance of the fiber, potential limitation and drawbacks, and factors affecting fiber morphology, and sintering temperature for impurity-free fibers. Information on relevant methodologies for cell fabrication and stability issues, polarization resistances, area specific resistance, conductivity, and power densities are summarized in the paper, and technology limitations, research challenges, and future trends are also discussed. The concluded information benefits improvement of the material properties and optimization of microstructure of the electrodes for SOFCs.

The miscibility and spatial distribution of the components in electrospun polymer–protein mats

Biodegradable blended electrospun mats are promising for biomedical applications such as wound dressing, tissue engineering, and drug delivery. Electrospun mats based on polyesters can be modified by the addition of other polymers or proteins to accelerate the degradation, improve mechanical properties or biocompatibility. However, relatively little is known about the distribution of the components throughout the blended mats. In the present work, we prepared polylactide (PLA), bovine serum albumin (BSA), and the blended PLA–BSA electrospun mats. We demonstrated that PLA and BSA are miscible in a common solvent HFIP (1,1,1,3,3,3-hexafluoro-2-propanol) at concentrations below 3%, but become immiscible as concentration increases. We used three methods (fluorescence microscopy, EDX, and Raman microspectroscopy) to validate that PLA and BSA can be blended in a single electrospun fiber despite the phase separation in the blend. The homogeneity of the blend influences on the homogeneity of the distribution of PLA and BSA components throughout the electrospun mat, as measured by Raman microspectroscopy. When the blended electrospun mats were incubated in water, they demonstrated the prolonged release of BSA. The presented results show a step-by-step approach for manufacturing blended electrospun mats made of immiscible components, which involves the analysis of component miscibility, the mat morphology, and composition. This approach can be used for the rational design of multicomponent electrospun mats.

Polylactide and bovine serum albumin can be combined in a single electrospun fiber, despite the phase separation.

Sputtering of Electrospun Polymer-Based Nanofibers for Biomedical Applications: A Perspective

Electrospinning has gained wide attention recently in biomedical applications. Electrospun biocompatible scaffolds are well-known for biomedical applications such as drug delivery, wound dressing, and tissue engineering applications. In this review, the synthesis of polymer-based fiber composites using an electrospinning technique is discussed. Formerly, metal particles were then deposited on the surface of electrospun fibers using sputtering technology. Key nanometals for biomedical applications including silver and copper nanoparticles are discussed throughout this review. The formulated scaffolds were found to be suitable candidates for biomedical uses such as antibacterial coatings, surface modification for improving biocompatibility, and tissue engineering. This review briefly mentions the characteristics of the nanostructures while focusing on how nanostructures hold potential for a wide range of biomedical applications.

Biomedical Applications of Electrospun Nanofibers: Drug and Nanoparticle Delivery

The electrospinning process has gained popularity due to its ease of use, simplicity and diverse applications. The properties of electrospun fibers can be controlled by modifying either process variables (e.g., applied voltage, solution flow rate, and distance between charged capillary and collector) or polymeric solution properties (e.g., concentration, molecular weight, viscosity, surface tension, solvent volatility, conductivity, and surface charge density). However, many variables affecting electrospinning are interdependent. An optimized electrospinning process is one in which these parameters remain constant and continuously produce nanofibers consistent in physicochemical properties. In addition, nozzle configurations, such as single nozzle, coaxial, multi-jet electrospinning, have an impact on the fiber characteristics. The polymeric solution could be aqueous, a polymeric melt or an emulsion, which in turn leads to different types of nanofiber formation. Nanofiber properties can also be modified by polarity inversion and by varying the collector design. The active moiety is incorporated into polymeric fibers by blending, surface modification or emulsion formation. The nanofibers can be further modified to deliver multiple drugs, and multilayer polymer coating allows sustained release of the incorporated active moiety. Electrospun nanofibers prepared from polymers are used to deliver antibiotic and anticancer agents, DNA, RNA, proteins and growth factors. This review provides a compilation of studies involving the use of electrospun fibers in biomedical applications with emphasis on nanoparticle-impregnated nanofibers.

Physicomechanical and antibacterial properties of experimental resin-based dental sealants modified with nylon-6 and chitosan nanofibers

This study aimed to develop and evaluate resin-based experimental dental sealants containing electrospun nylon-6 (N6) and chitosan (CH) fibers in an attempt to improve the physicomechanical properties and provide an antibacterial protective effect, respectively. Electrospun N6 and CH mats were immersed into a resin mixture, light-cured, and then cryomilled to obtain micron-sized resin-modified fiber particles. Different levels of the novel cryomilled particles (i.e. 1, 2.5, and 5% relative to the resin mixture, % by weight) were used to prepare the N6- and CH-containing sealants. A commercial sealant and the experimental resin mixture (unfilled) were used as controls. Flexural strength (FS), Vickers microhardness (VH), and agar diffusion tests were performed. The data were analyzed at the 5% significance level. No significant difference in fiber diameter of N6 (503 ± 31 nm) and CH (595 ± 38 nm) was observed. Upon cryomilling, the resin-modified CH and N6 mats led to the formation of irregularly-shaped particles, with an average diameter of 14.24 µm and 15.87 µm, respectively. CH-5% had significantly higher FS (115.3 ± 1.3 MPa) than all the other groups. CH-1% had significantly higher hardness values (38.3 ± 0.3 VHN) than all the other groups. Collectively, the results indicated that CH-containing sealants presented the highest FS and hardness; however, none of the CH-containing sealants displayed antimicrobial properties.

Fabrication of porous synthetic polymer scaffolds for tissue engineering

Tissue engineering provides a novel and promising approach to replace damaged tissue with an artificial substitute. Porous synthetic biodegradable polymers are the preferred materials for this substitution due to their microstructure, biocompatibility, biodegradability, and low cost. As a crucial element in tissue engineering, a scaffold acts as an artificial extracellular matrix (ECM) and provides support for cell migration, differentiation, and reproduction. The fabrication of viable scaffolds, however, has been a challenge in both clinical and academic settings. Methods such as solvent casting/particle leaching, thermally induced phase separation (TIPS), electrospinning, gas foaming, and rapid prototyping (additive manufacturing) have been developed or introduced for scaffold fabrication. Each method has its own advantages and disadvantages. In this review, the commonly used synthetic polymer scaffold fabrication methods will be introduced and discussed in detail, and recent progress regarding scaffold fabrication—such as combining different scaffold fabrication methods, combining various materials, and improving current scaffold fabrication methods—will be reviewed as well.

A facile approach to fabricate porous nanocomposite gels based on partially hydrolyzed polyacrylamide and cellulose nanocrystals for adsorbing methylene blue at low concentrations

Porous nanocomposite gels were fabricated by a facile method consisting of the electrospinning and subsequent heat treatment based on partially hydrolyzed polyacrylamide (HPAM) of ultra-high molecular weight, with cellulose nanocrystals (CNCs) as crosslinker. The effects of three electrospinning parameters (i.e., solution concentration, composition of solvent mixture, and CNC loading level) on morphology and diameter of electrospun fibers were systematically investigated. The swelling properties of porous gels and their application in the removal of methylene blue dye (as a compound representative of contaminants) were evaluated. Electrospun fiber morphologies without beads, branches, and ribbons were achieved by optimizing the electrospinning solutions. The thermal crosslinking between HPAM and CNCs was realized through esterification, rendering the product nanocomposite membranes insoluble in water. Electrospun fibers of approximately 220 nm in diameter comprised the 3D porous nanocomposite gels, with porosity greater than 50%. The porous nanocomposite gels displayed a rapid swelling rate and an efficient adsorption capacity in removing methylene blue at low concentrations from aqueous solutions.

One-dimensional composite nanomaterials: synthesis by electrospinning and their applications

This Review provides an overview of the synthesis of one-dimensional (1D) composite nanomaterials by electrospinning and their applications. After a brief description of the development of the electrospinning technique, the transformation of an inorganic nanocomponent or polymer into another kind of polymer or inorganic matrix is discussed in terms of the electrospinning process, including the direct-dispersed method, gas-solid reaction, in situ photoreduction, sol-gel method, emulsion electrospinning method, solvent evaporation, and coaxial electrospinning. In addition, various applications of such 1D composite nanomaterials are highlighted in terms of electronic and optical nanodevices, chemical and biological sensors, catalysis and electrocatalysis, superhydrophobic surfaces, environment, energy, and biomedical fields. An increasing number of investigations show that electrospinning has been not only a focus of academic study in the laboratory but is also being applied in a great many technological fields.

Preparation and Surface Modification of Poly(acrylonitrile-co-acrylic acid) Electrospun Nanofibrous Membranes

Poly(acrylonitrile-co-acrylic acid) (PANCAA) was synthesized and fabricated into nanofibrous membranes by an electrospinning technique. Scanning electron microscopy revealed that membranes composed of uniformly thin and smooth nanofibres were obtained under optimized processing parameters. Surface modification with chitosan on these nanofibrous membranes was accomplished by a coupling reaction between the carboxylic groups of PANCAA and the primary amino groups of chitosan. Fluorescent labelling, weight measurement, FT-IR/ATR spectroscopy, and X-ray photoelectron spectroscopy (XPS) were used to confirm the modification process and determine the immobilization degree of chitosan. Platelet adhesion experiments were further carried out to evaluate the hemocompatibility of the studied nanofibrous membranes. Preliminary results indicated that the immobilization of chitosan on the PANCAA nanofibrous membranes was favourable for platelet adhesion.