Cyclic fatigue resistance, torsional resistance, and metallurgical characteristics of V taper 2 and V taper 2H rotary NiTi files

Comparison of five single-file systems in the preparation of severely curved root canals: an ex vivo study

BACKGROUND

The ex vivo study is to compare the root canal preparation outcomes achieved by five nickel-titanium single-file instrumentation systems (M3-L, Reciproc Blue, V-Taper 2H, WaveOne Gold, XP-endo Shaper) in severely curved molar root canals.

METHODS

A total of 60 root canals were selected from extracted human molar teeth with curvatures ranging from 25° to 50° and divided into five groups based on the instrumentation system employed (n = 12). Before and after root canal preparation, a Micro-CT scan was taken, and pre- and post-operative data were analyzed to evaluate the following parameters: volume increment of root canals (VI), untouched root canal areas (UTA), and canal transportation (CT). Apically extruded debris (AD) was collected during preparation. After that, all samples were separated into two parts and examined respectively by scanning electron microscope (SEM) to assess cleaning ability. Data were statistically analyzed with ANOVA (UTA, AD, VI) or Kruskal-Wallis test (CT, SEM-score), the level of significance was set at α = 0.05.

RESULTS

There were no significant differences between the five systems regarding the AD, VI, and UTA parameters (P > 0.05). In terms of CT, no significant difference was noted at the straight section of canal and apical levels, while XP-endo Shaper showed less canal transportation than M3-L at the level of curved vertex (P < 0.05), and the centering ability of V-Taper 2H was significantly better than WaveOne Gold at the initial point of bending (P < 0.05). Debris and smear layers were present on the canal walls of all specimens, the apical thirds of the canal presented higher SEM scores than the coronal thirds in all groups (P < 0.05). Reciproc Blue and XP-endo Shaper showed fewer smear scores than WaveOne Gold in the apical thirds (P < 0.01 and P < 0.05, respectively), and no statistical difference was found between other groups in the middle and coronal thirds.

CONCLUSION

The five single-file systems evaluated performed equally in apically debris extrusion, dentin removal, and untouched root canal areas, while XP-endo Shaper and V-Taper 2H resulted in less canal transportation compared to M3-L and WaveOne Gold. Regarding cleaning ability, Reciproc Blue and XP-endo Shaper were associated with less smear layer than WaveOne Gold in the apical thirds.

Torsional Fracture Resistance of Niti Rotary Glide Path Files under Flexural Stress

This study aimed to evaluate the effects of flexural stress on the torsional fracture resistance of NiTi glide path files. PathFile #16/02, RaCe #15/04, RaCe Evo #15/04, HyFlex EDM #15/03, TruNatomy Glider #17/02, and V Taper 2H #17/04 were examined by scanning electron microscopy (SEM) (n = 3/brand) and subjected to differential scanning calorimetry (n = 2/brand). Torsional fracture resistance testing was performed in straight (ISO 3630-1) and flexural modes (n = 15/brand/mode). Flexural mode testing involved instruments rotating within a stainless-steel artificial double-curved canal. Ultimate strength and distortion angle until failure were recorded, and fractured instruments were examined by SEM. Statistical analyses involved independent sample t-test and one-way analysis of variance with Games–Howell pots hoc test. Austenitic transformation- finishing temperatures of heat-treated files were above body temperature. For RaCe Evo, HyFlex EDM, TruNatomy Glider, and V Taper 2H, the flexural mode resulted in a significantly higher distortion angle compared to the straight mode (p < 0.05). The maximum torque of RaCe Evo, HyFlex EDM increased with the flexural stress (p < 0.05). V taper 2H showed the highest distortion angle and ultimate strength. SEM showed typical patterns of torsional fracture for all tested files. The flexural stress positively affected distortion angle of heat-treated NiTi glide path files.

Nitinol Type Alloys General Characteristics and Applications in Endodontics

A very extensive literature review presents the possibilities and needs of using, in endodontics, the alloys commonly known as nitinol. Nitinol, as the most modern group of engineering materials used to develop root canals, is equilibrium nickel and titanium alloys in terms of the elements’ atomic concentration, or very similar. The main audience of this paper is engineers, tool designers and manufacturers, PhD students, and students of materials and manufacturing engineering but this article can also certainly be used by dentists. The paper aims to present a full material science characterization of the structure and properties of nitinol alloys and to discuss all structural phenomena that determine the performance properties of these alloys, including those applied to manufacture the endodontic tools. The paper presents the selection of these alloys’ chemical composition and processing conditions and their importance in the endodontic treatment of teeth. The results of laboratory studies on the analysis of changes during the sterilization of endodontic instruments made of nitinol alloys are also included. The summary of all the literature analyses is an SWOT analysis of strengths, weaknesses, opportunities, and threats, and is a forecast of the development strategy of this material in a specific application such as endodontics.

Assessment of Real-Time Operative Torque during Nickel–Titanium Instrumentation with Different Lubricants

The aim of the present study is twofold: to assess ex vivo the role of different lubricants on real-time torque generated during intracanal instrumentation and to check whether two different kinds of torque parameters, operative torque (OT) and average peak torque (APT), could produce similar results. Forty extracted single-rooted teeth were selected for the present study and divided into four equal groups (n = 10): Group A, NaCl 0.2%; Group B, NaOCl 5%; Group C, ethylenediaminetetraacetate (EDTA), and Group D, EDTA and hydrogen peroxide. Afterwards, Edge Taper F2 (Edge Endo, Albuquerque, New Mexico) were rotated clockwise at 300 rpm with 3 Ncm maximum torque by an endodontic torque recording motor. In each sample, mean OT and mean APT were recorded and statistically analyzed with one-way ANOVA and a post hoc Bonferroni between groups (p < 0.05). EDTA (12.11 ± 4.45 Ncm) showed statistically significant (p < 0.05) lower values compared with the other tested irrigant for both parameters. Overall, the two different parameters were both able to differentiate between the influence of lubricants on torsional loads.

Torsional and Bending Properties of V Taper 2H, ProTaper NEXT, NRT, and One Shape

Nickel-titanium (NiTi) rotary files have enabled efficient root canal preparations that maintain the canal center with fewer aberrations compared to hand files. However, NiTi rotary files are susceptible to fracture, which can thereby compromise root canal treatment. Therefore, NiTi files have been developed to enhance fracture resistance by modifying design and thermal treatment. The objective of this study was to compare the torsional fatigue resistance and bending resistance of NiTi files manufactured from different alloys and treatments. ProTaper NEXT X2 (PTN; M-wire), V taper 2H (V2H; controlled memory wire), NRT (heat-treated), and One Shape (OS; conventional alloy) instruments of tip size #25 were compared. Torsional fatigue was evaluated by embedding the 3 mm tip of each instrument (N = 10/brand) in resin and the repetitive application of torsional stress (300 rpm, 1.0 N·cm) by an endodontic motor with autostop when the file fractured. The number of loading cycles to fracture was recorded and analyzed by Kruskal–Wallis and Mann–Whitney U tests with Bonferroni's correction. Bending resistance of the instruments was tested using a cantilever bending test to the 3 mm point from the tip (N = 10/brand). The stress was measured when deflection of 3 mm was subjected and statistically analyzed with a one-way analysis of variance and Tukey's honest significance difference test (α = 0.05). V2H withstood the highest number of load applications during torsional fatigue testing (p < 0.05), followed by NRT, PTN, and OS, where the differences between NRT and PTN (p=0.035) and between PTN and OS (p=0.143) were not statistically significant. V2H showed the lowest bending stiffness, followed by NRT, PTN, and OS (p < 0.001). Thermal treatment of NiTi wire resulted in improved mechanical properties, and controlled memory wire provided improved flexibility and torsional fatigue resistance.

Cyclic fatigue resistance of M-Pro and RaCe Ni-Ti rotary endodontic instruments in artificial curved canals: a comparative in vitro study

Objectives

To compare the flexural cyclic fatigue resistance and the length of the fractured segments (FLs) of recently introduced M-Pro rotary files with that of RaCe rotary files in curved canals and to evaluate the fracture surface by scanning electron microscopy (SEM).

Materials and Methods

Thirty-six endodontic files with the same tip size and taper (size 25, 0.06 taper) were used. The samples were classified into 2 groups (n = 18): the M-Pro group (M-Pro IMD) and the RaCe group (FKG). A custom-made simulated canal model was fabricated to evaluate the total number of cycles to failure and the FL. SEM was used to examine the fracture surfaces of the fragmented segments. The data were statistically analyzed and comparisons between the 2 groups for normally distributed numerical variables were carried out using the independent Student's t-test. A p value less than 0.05 was considered to indicate statistical significance.

Results

The M-Pro group showed significantly higher resistance to flexural cyclic fatigue than the RaCe group (p < 0.05), but there was no significant difference in the FLs between the 2 groups (p ≥ 0.05).

Conclusions

Thermal treatment of nickel-titanium instruments can improve the flexural cyclic fatigue resistance of rotary endodontic files, and the M-Pro rotary system seems to be a promising rotary endodontic file.

Cyclic fatigue resistance, torsional resistance, and metallurgical characteristics of M3 Rotary and M3 Pro Gold NiTi files

Objectives

To evaluate the mechanical properties and metallurgical characteristics of the M3 Rotary and M3 Pro Gold files (United Dental).

Materials and Methods

One hundred and sixty new M3 Rotary and M3 Pro Gold files (sizes 20/0.04 and 25/0.04) were used. Torque and angle of rotation at failure (n = 20) were measured according to ISO 3630-1. Cyclic fatigue resistance was tested by measuring the number of cycles to failure in an artificial stainless steel canal (60° angle of curvature and a 5-mm radius). The metallurgical characteristics were investigated by differential scanning calorimetry. Data were analyzed using analysis of variance and the Student-Newman-Keuls test.

Results

Comparing the same size of the 2 different instruments, cyclic fatigue resistance was significantly higher in the M3 Pro Gold files than in the M3 Rotary files (p < 0.001). No significant difference was observed between the files in the maximum torque load, while a significantly higher angular rotation to fracture was observed for M3 Pro Gold (p < 0.05). In the DSC analysis, the M3 Pro Gold files showed one prominent peak on the heating curve and 2 prominent peaks on the cooling curve. In contrast, the M3 Rotary files showed 1 small peak on the heating curve and 1 small peak on the cooling curve.

Conclusions

The M3 Pro Gold files showed greater flexibility and angular rotation than the M3 Rotary files, without decrement of their torque resistance. The superior flexibility of M3 Pro Gold files can be attributed to their martensite phase.

Microscopic Features of Fractured Fragment of Nickel-Titanium Endodontic Instruments by Two Different Modes of Torsional Loading

This study compared the microscopic features of the fractured endodontic nickel-titanium (NiTi) rotary instruments by two different torsional loadings: repetitive torsional loading (RTL) and single torsional loading (STL) based on the International Organization for Standardization (ISO). ProTaper Next, HyFlex EDM, and V-Taper 2 were compared in this study. In the STL method, the torsional load was applied after fixing the 3 mm tip of the file, by continuous clockwise rotation (2 rpm) until fracture. In the RTL method, a preset rotational loading (0.5 N·cm) was applied and the clockwise loading to the preset torque and counterclockwise unloading to original position were repeated at 50 rpm until the file fractured. Fractured fragments by two methods were compared under a scanning electron microscope (SEM) to examine the topographic features of the fractured surfaces and longitudinal aspects. SEM examinations showed significantly different features according to the loading methods. Specimens from the RTL method showed ruptured aspects on cross sections, with multiple areas of initiated cracks while the STL method showed the typical features of torsional failure, such as circular abrasion marks and fatigue dimples. This study suggested a new repetitive torsional loading method which is much more clinically relevant and may result in a different fracture feature from STL method.

Evaluation of dynamic and static torsional resistances of nickel-titanium rotary instruments

Background/purpose

This study evaluated the torsional resistances of nickel-titanium rotary instruments by two methods: i) dynamic resistance: repetitive torsional loading (RTL) and ii) static resistance: single torsional loading (STL) based on the International Organization for Standardization.

Materials and methods

In RTL method, a pre-set rotational loading (0.5 N cm) was applied after fixing the 3-mm tip of the file, and this clockwise loading to the pre-set torque and counter-clockwise unloading to original position was repeated at 50 rpm until the file fractured. The number of repetition cycles until fracture was counted. In STL method, the torsional strength was determined by continuous clockwise rotation (2 rpm) until fracture. Results from both methods were compared after testing the torsional resistances of four instrument systems (n = 15): Hyflex CM, HyFlex EDM, V-Taper2, and V-Taper2H. A scanning electron microscope (SEM) was used to examine the topographic features of the fractured surfaces and longitudinal aspects (n = 5) from both methods.

Results

The RTL and STL methods had similar results: V-Taper2 had the highest resistance and the Hyflex CM had the lowest (P < 0.05). Spearman correlation test showed the results from two methods were strongly correlated (coefficient = 1). Under the SEM, specimens from the RTL showed ruptured aspects on cross-sections with multiple areas of crack propagation, while the STL showed the typical features of torsional failure such as circular abrasion marks and fatigue dimples.

Conclusions

This study suggests the clinically relevant torsional test (RTL) method yield similar results with the STL method, but they have different topographic findings.

Various heat-treated nickel-titanium rotary instruments evaluated in S-shaped simulated resin canals

Background/purpose

Heat treatment of nickel–titanium (NiTi) alloy produces a better arrangement of the crystal structure, thereby leading to increased flexibility and improved fatigue resistance or plastic behavior. This study aimed to assess the performance of various heat-treated NiTi rotary instruments in S-shaped resin canals.

Materials and methods

Forty S-shaped resin canals were instrumented (10/group) with either Twisted Files (R-phase), WaveOne (M-wire), Hyflex CM, or V Taper 2H (CM-wire) with the same apical size and taper (25/0.08). Each S-shaped resin canal was scanned both before and after instrumentation with microcomputed tomography. Changes in canal volume and transportation were evaluated at regular intervals (0.5 mm). Differences between instruments at the apical curve, coronal curve, and straight portion of the canals were analyzed statistically.

Results

All tested instruments caused more transportation at the coronal rather than apical curvatures, with the exception of Twisted Files for which apical transportation was the highest for any instrument or location (P < 0.05). The transportation was mostly influenced by the alloy type rather than their cross-sectional characteristics (P < 0.05). The volumetric increase after instrumentation was similar for all tested instruments at the apical curve (P > 0.05), whereas Hyflex CM created the most conservative preparations at the coronal curve (P < 0.05). At the straight portion, volumetric changes were largest for Twisted Files and smallest for V Taper 2H (P < 0.05).

Conclusion

Amongst heat-treated NiTi instruments, the CM-wire based instruments created the most favorable preparations in S-shaped resin canals.