A Near-Infrared Photothermal-Responsive Underwater Adhesive with Tough Adhesion and Antibacterial Properties

Developing tunable underwater adhesives that possess tough adhesion in service and easy detachment when required remains challenging. Herein, a strategy is proposed to design a near infrared (NIR) photothermal-responsive underwater adhesive by incorporating MXene (Ti3C2Tx)-based nanoparticles within isocyanate-modified polydimethylsiloxane (PDMS) polymer chains. The developed adhesive exhibits long-term and tough adhesion with an underwater adhesion strength reaching 5.478 MPa. Such strong adhesion is mainly attributed to the covalent bonds and hydrogen bonds at the adhesive-substrate interface. By making use of the photothermal-response of MXene-based nanoparticles and the thermal response of PDMS-based chains, the adhesive possesses photothermal-responsive performance, exhibiting sharply diminished adhesion under NIR irradiation. Such NIR-triggered tunable adhesion allows for easy and active detachment of the adhesive when needed. Moreover, the underwater adhesive exhibits photothermal antibacterial property, making it highly desirable for underwater applications. This work enhances the understanding of photothermal-responsive underwater adhesion, enabling the design of tunable underwater adhesives for biomedical and engineering applications.

Hydrophobic Recovery of Plasma-Hydrophilized Polyethylene Terephthalate Polymers

Oxygen plasma is widely used for enhancing the wettability of numerous polymers, including polyethylene terephthalate (PET). The treatment with plasma containing oxygen will cause surface functionalization with polar functional groups, which will, in turn, improve the wettability. However, the exact mechanisms leading to the hydrophilic or even super-hydrophilic surface finish are still insufficiently explored. The wettability obtained by plasma treatment is not permanent, since the hydrophobic recovery is usually reported. The mechanisms of hydrophobic recovery are reviewed and explained. Methods for suppressing this effect are disclosed and explained. The recommended treatment which assures stable hydrophilicity of PET samples is the treatment with energetic ions and/or vacuum ultraviolet radiation (VUV). The influence of various plasma species on the formation of the highly hydrophilic surface finish and stability of adequate wettability of PET materials is discussed.

Porphyrin-Based Supramolecular Flags in the Thermal Gradients' Wind: What Breaks the Symmetry, How and Why

The Spontaneous Symmetry Breaking (SSB) phenomenon is a natural event in which a system changes its symmetric state, apparently reasonless, in an asymmetrical one. Nevertheless, this occurrence could be hiding unknown inductive forces. An intriguing investigation pathway uses supramolecular aggregates of suitable achiral porphyrins, useful to mimic the natural light-harvesting systems (as chlorophyll). Using as SSB probe supramolecular aggregates of 5,10,15,20-tetrakis[p(ω-methoxypolyethyleneoxy)phenyl]porphyrin (StarP), a non-ionic achiral PEGylated porphyrin, we explore here its interaction with weak asymmetric thermal gradients fields. The cross-correlation of the experimental data (circular dichroism, confocal microscopy, atomic force microscopy, and cryo-transmission electron microscopy) revealed that the used building blocks aggregate spontaneously, organizing in flag-like structures whose thermally-induced circular dichroism depends on their features. Finally, thermal gradient-induced enantioselectivity of the supramolecular flag-like aggregates has been shown and linked to their size-dependence mesoscopic deformation, which could be visualized as waving flags in the wind.

Facile Fabrication of Microwrinkled Poly(3,4-Ethylenedioxythiophene) Films that Promote Neural Differentiation under Electrical Stimulation

Although conductive bioelectronic interfaces (BEIs) can allow neural cell culturing while providing electrical stimulation (ES) to the nervous system, there are few simple approaches for the preparation of conductive BEIs with topographical features designed for cell manipulation. In this study, we developed a facile method for fabricating microwrinkled poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) films through spin-coating onto pre-elongated polydimethylsiloxane substrates. The microwrinkles of our PEDOT:PSS films pre-elongated by 20 and 40% had average widths of 6.47 ± 1.49 and 5.39 ± 1.53 μm, respectively. These microwrinkled PEDOT:PSS films promoted the directional ordering of neurite outgrowth of PC12 cells and displayed favorable biocompatibility and outstanding electrochemical properties for long-term ES treatment. When using this BEI platform, the level of PC12 gene expression of Neun was enhanced significantly after 5 days of culturing in differentiation media and under ES, in line with the decreased expression of early phase markers. Therefore, such readily fabricated microwrinkled PEDOT:PSS films are promising candidates for use as BEIs for tissue regenerative medicine.

Impact of Plasma Pre-Treatment on the Tribological Properties of DLC Coatings on PDMS Substrates

The processes of the deposition of carbon coatings on PDMS (polydimethylsiloxane) substrates using plasma techniques are widely used in a large number of studies, in applications ranging from electronic to biological. That is why the potential improvement of their functional properties, including tribological properties, seems very interesting. This paper presents an analysis of the impact of plasma pre-treatment on the properties of the produced diamond-like carbon (DLC) coatings, including changes in the coefficients of friction and wear rates. The initial modification processes were performed using two different techniques based on low-pressure plasma (RF PACVD, radio-frequency plasma-assisted chemical vapour deposition) and dielectric barrier discharge (DBD) plasma. The effects of the above-mentioned treatments on the geometric structure of the PDMS surface and its water contact angles and stability over time were determined. The basic properties of the DLC coatings produced on unmodified substrates were compared to those of the coatings subjected to plasma pre-treatment. The most interesting effects in terms of tribological properties were achieved after the DBD process and production of DLC coatings, achieving a decrease in wear rates to 2.45 × 10⁻⁸ mm³/Nm. The tests demonstrate that the cross-linking of the polymer substrate occurs during plasma pre-treatment.

Preparation of Twisted Bilayer Graphene via the Wetting Transfer Method

Assembling monolayers into a bilayer system unlocks the rotational free degree of van der Waals (vdW) homo/heterostructure, enabling the building of twisted bilayer graphene (tBLG) which possesses novel electronic, optical, and mechanical properties. Previous methods for preparation of homo/heterstructures inevitably leave the polymer residue or hexagonal boron nitride (h-BN) mask, which usually obstructs the measurement of intrinsic mechanical and surface properties of tBLG. Undoubtedly, to fabricate the designable tBLG with clean interface and surface is necessary but challenging. Here, we propose a simple and handy method to prepare atomically clean twisted bilayer graphene with controllable twist angles based on wetting-induced delamination. This method can transfer tBLG onto a patterned substrate, which offers an excellent platform for the observation of physical phenomena such as relaxation of moiré pattern in marginally tBLG. These findings and insight should ultimately guide the designable packaging and atomic characterization of the two-dimensional (2D) materials.

Adhesive-free adhesion between heat-assisted plasma-treated fluoropolymers (PTFE, PFA) and plasma-jet-treated polydimethylsiloxane (PDMS) and its application

Conventional low-temperature plasma treatment was reported to minimally improve the adhesion property of polytetrafluoroethylene (PTFE), whereas heat-assisted plasma (HAP) treatment significantly improved the same. An unvulcanized rubber was previously used as an adherent for PTFE. This study aimed to achieve strong adhesive-free adhesion between PTFE and vulcanized polydimethylsiloxane (PDMS) rubber. As-received vulcanized PDMS rubber did not adhere to HAP-treated PTFE, and as-received PTFE did not adhere to vulcanized rubber of plasma-jet (PJ) treated PDMS rubber; however, HAP-treated PTFE strongly adhered to vulcanized PJ-treated PDMS rubber, and both PTFE and PDMS exhibited cohesion failure in the T-peel test. The surface chemical compositions of the PTFE and PDMS sides were determined using X-ray photoelectron spectroscopy. The strong PTFE/PDMS adhesion was explained via hydrogen and covalent bond formation (C–O–Si and/or C(=O)–O–Si) between hydroxyl (C–OH) or carboxyl (C(=O)–OH) groups of the HAP-treated PTFE. This process was also applied to adhesive-free adhesion between a tetrafluoroethylene–perfluoroalkylvinylether copolymer (PFA) and PDMS; subsequently, a translucent PFA/PDMS assembly with strong adhesion was realized together with the PTFE/PDMS assembly. Strong adhesive-free adhesion between fluoropolymers (PTFE, PFA) and vulcanized PDMS rubber without using any adhesives and graft polymer was successfully realized upon plasma treatment of both the fluoropolymer and PDMS sides. Additionally, a PDMS sheet, which was PJ-treated on both sides, was applied to strongly adhere fluoropolymers (PTFE, PFA) to materials such as metal and glass. PJ-treated PDMS was used as an intermediate layer rather than a strong adhesive, achieving PTFE/PDMS/metal and PTFE/PDMS/glass assemblies. The PTFE/PDMS, PDMS/metal, and PDMS/glass adhesion strengths exceeded 2 N/mm.

Microcapillary-like structures prompted by phospholipase A2 activation in endothelial cells and pericytes co-cultures on a polyhydroxymethylsiloxane thin film

A thin film of poly(hydroxymethylsiloxane) (PHMS) has been deposited on glass dishes and tested as artificial support material for vascularization from mixed cultures of endothelial cells (EC) and pericytes (PC). The EC/PC co-cultures adhered massively on PHMS, with the formation of net-like microcapillary structures. Such evidence was not found on control glass substrates in the same co-culture conditions neither on PHMS for EC and PC in monocultures. The physicochemical characterization of PHMS and control glass surface by time-of-flight secondary ion mass spectrometry, X-ray photoelectron spectroscopy, water contact angle and atomic force microscopy, pointed to the main role of the polymer hydrophobilicy to explain the observed cellular behavior. Moreover, enhanced intercellular cross-talk was evidenced by the up-regulation and activation of cytoplasmic and Ca(2+)-independent phospholipase A(2) (cPLA(2) and iPLA(2)) expression and cPLA(2) phosphorylation, leading to the cell proliferation and microcapillary formation on the PHMS surface, as evidenced by confocal microscopy analyses. Co-cultures, established with growth-arrested PCs by treatment with mitomycin C, showed an increase in EC proliferation on PHMS. AACOCF(3) or co-transfection with cPLA(2) and iPLA(2)siRNA reduced cell proliferation. The results highlight the major role played by EC/PC cross-talk as well as the hydrophobic character of the substrate surface, to promote microcapillary formation. Our findings suggest an attractive strategy for vascular tissue engineering and provide new details on the interplay of artificial substrates and capillary formation.

Plasma oxidized polyhydroxymethylsiloxane--a new smooth surface for supported lipid bilayer formation

A novel substrate for preparation of supported lipid bilayers (SLBs), smooth at the subnanometer scale and of variable thickness from ten to several hundred nanometers, was developed by surface oxidation of spin-coated poly(hydroxymethylsiloxane) (PHMS) films. The deposited polymeric thin films were modified by a combination of oxygen plasma and thermal treatment (PHMS(ox)), in order to convert the outermost surface layer of the polymer film to a stable SiO(2) film, suitable for SLB formation. The hydrophilic, SiO(2)-like surfaces were characterized by XPS, wetting angle, ellipsometry, and AFM. Lipid bilayers were formed on this surface using the well-known vesicle adsorption-rupture-fusion process, usually performed on glass or vapor-deposited SiO(2). Reproducible formation of homogeneous SLBs of different compositions (POPC, DOEPC, and POPC/DOPS) was demonstrated on the new SiO(2) surface by quartz crystal microbalance with dissipation (QCM-D), surface plasmon resonance (SPR), and optical reflectometry measurements. The SLB formation kinetics on the PHMS(ox)-coated sensors showed very similar characteristics, for all investigated PHMS thicknesses, as on reference sensors coated with vapor-deposited SiO(2). The good adhesive properties of the PHMS to gold allows for the preparation of thin PHMS(ox) layers compatible with SPR. The much smaller roughness at the nanometer scale of the PHMS(ox) surfaces, compared to standard vapor-deposited SiO(2)-coated sensors, makes them advantageous for AFM and optical experiments and promising for patterning. To benefit optical experiments with the PHMS(ox) surfaces, it was also investigated how the PHMS film thickness influences the SPR and reflectometry responses upon SLB formation.