Solvent-cast three-dimensional printing of multifunctional microsystems

Comparative evaluation of melt- vs. solution-printed poly(ε-caprolactone)/hydroxyapatite scaffolds for bone tissue engineering applications

Material extrusion-based three-dimensional (3D) printing is a widely used manufacturing technology for fabricating scaffolds and devices in bone tissue engineering (BTE). This technique involves two fundamentally different extrusion approaches: solution-based and melt-based printing. In solution-based printing, a polymer solution is extruded and solidifies via solvent evaporation, whereas in melt-based printing, the polymer is melted at elevated temperatures and solidifies as it cools post-extrusion. Solution-based printing can also be enhanced to generate micro/nano-scale porosity through phase separation by printing the solution into a nonsolvent bath. The choice of the printing method directly affects scaffold properties and the biological response of stem cells. In this study, we selected polycaprolactone (PCL), a biodegradable polymer frequently used in BTE, blended with hydroxyapatite (HA) nanoparticles, a bioceramic known for promoting bone formation, to investigate the effects of the printing approach on scaffold properties and performance in vitro using human mesenchymal stem cells (hMSCs). Our results showed that while both printing methods produced scaffolds with similar strut and overall scaffold dimensions, solvent-based printing resulted in porous struts, higher surface roughness, lower stiffness, and increased crystallinity compared to melt-based printing. Although stem cell viability and proliferation were not significantly influenced by the printing approach, melt-printed scaffolds promoted a more spread morphology and exhibited pronounced vinculin staining. Furthermore, composite scaffolds outperformed their neat counterparts, with melt-printed composite scaffolds significantly enhancing bone formation. This study highlights the critical role of the printing process in determining scaffold properties and performance, providing valuable insights for optimizing scaffold design in BTE.

Polymer microsphere inks for semi-solid extrusion 3D printing at ambient conditions

Extrusion-based 3D printing methods have great potential for manufacturing of personalized polymer-based drug-releasing systems. However, traditional melt-based extrusion techniques are often unsuitable for processing thermally labile molecules. Consequently, methods that utilize the extrusion of semi-solid inks under mild conditions are frequently employed. The rheological properties of the semi-solid inks have a substantial impact on the 3D printability, making it necessary to evaluate and tailor these properties. Here, we report a novel semi-solid extrusion 3D printing method based on utilization of a Carbopol gel matrix containing various concentrations of polymeric microspheres. We also demonstrate the use of a solvent vapor-based post-processing method for enhancing the mechanical strength of the printed objects. As our approach enables room-temperature processing of polymers typically used in the pharmaceutical industry, it may also facilitate the broader application of 3D printing and microsphere technologies in preparation of personalized medicine.

Solvent-cast 3D printing with molecular weight polymer blends to decouple effects of scaffold architecture and mechanical properties on mesenchymal stromal cell fate

The biochemical and physical properties of a scaffold can be tailored to elicit specific cellular responses. However, it is challenging to decouple their individual effects on cell-material interactions. Here, we solvent-cast 3D printed different ratios of high and low molecular weight (MW) poly(caprolactone) (PCL) to fabricate scaffolds with significantly different stiffnesses without affecting other properties. Ink viscosity was used to match processing conditions between inks and generate scaffolds with the same surface chemistry, crystallinity, filament diameter, and architecture. Increasing the ratio of low MW PCL resulted in a significant decrease in modulus. Scaffold modulus did not affect human mesenchymal stromal cell (hMSC) differentiation under osteogenic conditions. However, hMSC response was significantly affected by scaffold stiffness in chondrogenic media. Low stiffness promoted more stable chondrogenesis whereas high stiffness drove hMSC progression toward hypertrophy. These data illustrate how this versatile platform can be used to independently modify biochemical and physical cues in a single scaffold to synergistically enhance desired cellular response.

Additive Manufacturing of Poly(phenylene Sulfide) Aerogels via Simultaneous Material Extrusion and Thermally Induced Phase Separation

Additive manufacturing (AM) of aerogels increases the achievable geometric complexity, and affords fabrication of hierarchically porous structures. In this work, a custom heated material extrusion (MEX) device prints aerogels of poly(phenylene sulfide) (PPS), an engineering thermoplastic, via in situ thermally induced phase separation (TIPS). First, pre-prepared solid gel inks are dissolved at high temperatures in the heated extruder barrel to form a homogeneous polymer solution. Solutions are then extruded onto a room-temperature substrate, where printed roads maintain their bead shape and rapidly solidify via TIPS, thus enabling layer-wise MEX AM. Printed gels are converted to aerogels via postprocessing solvent exchange and freeze-drying. This work explores the effect of ink composition on printed aerogel morphology and thermomechanical properties. Scanning electron microscopy micrographs reveal complex hierarchical microstructures that are compositionally dependent. Printed aerogels demonstrate tailorable porosities (50.0-74.8%) and densities (0.345-0.684 g cm-3), which align well with cast aerogel analogs. Differential scanning calorimetry thermograms indicate printed aerogels are highly crystalline (≈43%), suggesting that printing does not inhibit the solidification process occurring during TIPS (polymer crystallization). Uniaxial compression testing reveals that compositionally dependent microstructure governs aerogel mechanical behavior, with compressive moduli ranging from 33.0 to 106.5 MPa.

Intelligent Vascularized 3D/4D/5D/6D-Printed Tissue Scaffolds

Blood vessels are essential for nutrient and oxygen delivery and waste removal. Scaffold-repairing materials with functional vascular networks are widely used in bone tissue engineering. Additive manufacturing is a manufacturing technology that creates three-dimensional solids by stacking substances layer by layer, mainly including but not limited to 3D printing, but also 4D printing, 5D printing and 6D printing. It can be effectively combined with vascularization to meet the needs of vascularized tissue scaffolds by precisely tuning the mechanical structure and biological properties of smart vascular scaffolds. Herein, the development of neovascularization to vascularization to bone tissue engineering is systematically discussed in terms of the importance of vascularization to the tissue. Additionally, the research progress and future prospects of vascularized 3D printed scaffold materials are highlighted and presented in four categories: functional vascularized 3D printed scaffolds, cell-based vascularized 3D printed scaffolds, vascularized 3D printed scaffolds loaded with specific carriers and bionic vascularized 3D printed scaffolds. Finally, a brief review of vascularized additive manufacturing-tissue scaffolds in related tissues such as the vascular tissue engineering, cardiovascular system, skeletal muscle, soft tissue and a discussion of the challenges and development efforts leading to significant advances in intelligent vascularized tissue regeneration is presented.

Characterizing properties of scaffolds 3D printed with peptide-polymer conjugates

Three-dimensional (3D) printing is a popular biomaterials fabrication technique because it enables scaffold composition and architecture to be tuned for different applications. Modifying these properties can also alter mechanical properties, making it challenging to decouple biochemical and physical properties. In this study, inks containing peptide-poly(caprolactone) (PCL) conjugates were solvent-cast 3D printed to create peptide-functionalized scaffolds. We characterized how different concentrations of hyaluronic acid-binding (HAbind-PCL) or mineralizing (E3-PCL) conjugates influenced properties of the resulting 3D-printed constructs. The peptide sequences CGGGRYPISRPRKR (HAbind-PCL; positively charged) and CGGGAAAEEE (E3-PCL; negatively charged) enabled us to evaluate how conjugate chemistry, charge, and concentration affected 3D-printed architecture, conjugate location, and mechanical properties. For both HAbind-PCL and E3-PCL, conjugate addition did not affect ink viscosity, filament diameter, scaffold architecture, or scaffold compressive modulus. Increasing conjugate concentration in the ink prior to printing correlated with an increase in peptide concentration on the scaffold surface. Interestingly, conjugate type affected final conjugate location within the 3D-printed filament cross-section. HAbind-PCL conjugates remained within the filament bulk while E3-PCL conjugates were located closer to the filament surface. E3-PCL at all concentrations did not affect mechanical properties, but an intermediate HAbind-PCL concentration resulted in a moderate decrease in filament tensile modulus. These data suggest final conjugate location within the filament bulk may influence mechanical properties. However, no significant differences were observed between PCL filaments printed without conjugates and filaments printed with higher HAbind-PCL concentrations. These results demonstrate that this 3D printing platform can be used to functionalize the surface without significant changes to the physical properties of the scaffold. The downstream potential of this strategy will enable decoupling of biochemical and physical properties to fine-tune cellular responses and support functional tissue regeneration.

Antibacterial 3D-Printed Silver Nanoparticle/Poly Lactic-Co-Glycolic Acid (PLGA) Scaffolds for Bone Tissue Engineering

Infectious bone defects present a major challenge in the clinical setting currently. In order to address this issue, it is imperative to explore the development of bone tissue engineering scaffolds that are equipped with both antibacterial and bone regenerative capabilities. In this study, we fabricated antibacterial scaffolds using a silver nanoparticle/poly lactic-co-glycolic acid (AgNP/PLGA) material via a direct ink writing (DIW) 3D printing technique. The scaffolds' microstructure, mechanical properties, and biological attributes were rigorously assessed to determine their fitness for repairing bone defects. The surface pores of the AgNPs/PLGA scaffolds were uniform, and the AgNPs were evenly distributed within the scaffolds, as confirmed via scanning electron microscopy (SEM). Tensile testing confirmed that the addition of AgNPs enhanced the mechanical strength of the scaffolds. The release curves of the silver ions confirmed that the AgNPs/PLGA scaffolds released them continuously after an initial burst. The growth of hydroxyapatite (HAP) was characterized via SEM and X-ray diffraction (XRD). The results showed that HAP was deposited on the scaffolds, and also confirmed that the scaffolds had mixed with the AgNPs. All scaffolds containing AgNPs exhibited antibacterial properties against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). A cytotoxicity assay using mouse embryo osteoblast precursor cells (MC3T3-E1) showed that the scaffolds had excellent biocompatibility and could be used for repairing bone tissue. The study shows that the AgNPs/PLGA scaffolds have exceptional mechanical properties and biocompatibility, effectively inhibiting the growth of S. aureus and E. coli. These results demonstrate the potential application of 3D-printed AgNPs/PLGA scaffolds in bone tissue engineering.

Printability of Poly(lactic acid) Ink by Embedded 3D Printing via Immersion Precipitation

Immersion precipitation three-dimensional printing (ip3DP) and freeform polymer precipitation (FPP) are unique and versatile methods of 3D printing to fabricate 3D structures based on nonsolvent-induced phase separation via direct ink writing (DIW). Immersion precipitation involves complex dynamics among solvents, nonsolvents, and dissolved polymers, and the printability of 3D models in these methods requires further understanding. To this end, we characterized these two methods of 3D printing using polylactide (PLA) dissolved in dichloromethane (7.5-30% w/w) as model inks. We analyzed the rheological properties of the solutions and the effect of printing parameters on solvent-nonsolvent diffusion to achieve printability. The PLA inks exhibited shear-thinning properties, and their viscosities varied over three orders of magnitude (10^-1∼10² Pa·s). A processing map was presented to understand the ideal ranges of the concentration of PLA in inks and the nozzle diameter to ensure printability, and the fabrication of complex 3D structures was fabricated with adequate applied pressure and nozzle speed. The processing map also highlighted the advantages of embedded 3D printing over solvent-cast 3D printing based on solvent evaporation. Lastly, we demonstrated that the porosity of the interface and inner structure of the printed objects was readily tailored by the concentration of the PLA and the porogen added to the ink. The methods presented here offer new perspectives to fabricate micro-to-centimeter objects of thermoplastics with nanometer-scale inner pores and provide guidelines for successful embedded 3D printing based on immersion precipitation.

Vat Photopolymerization Additive Manufacturing of Tough, Fully Recyclable Thermosets

To advance the capabilities of additive manufacturing, novel resin formulations are needed that produce high-fidelity parts with desired mechanical properties that are also amenable to recycling. In this work, a thiol-ene-based system incorporating semicrystallinity and dynamic thioester bonds within polymer networks is presented. It is shown that these materials have ultimate toughness values >16 MJ cm^-3, comparable to high-performance literature precedents. Significantly, the treatment of these networks with excess thiols facilitates thiol-thioester exchange that degrades polymerized networks into functional oligomers. These oligomers are shown to be amenable to repolymerization into constructs with varying thermomechanical properties, including elastomeric networks that recover their shape fully from >100% strain. Using a commercial stereolithographic printer, these resin formulations are printed into functional objects including both stiff (E ∼ 10-100 MPa) and soft (E ∼ 1-10 MPa) lattice structures. Finally, it is shown that the incorporation of both dynamic chemistry and crystallinity further enables advancement in the properties and characteristics of printed parts, including attributes such as self-healing and shape-memory.

Multi-Spiral Laser Patterning of Azopolymer Thin Films for Generation of Orbital Angular Momentum Light

Recently, the realization of the spiral mass transfer of matter has attracted the attention of many researchers. Nano- and microstructures fabricated with such mass transfer can be used for the generation of light with non-zero orbital angular momentum (OAM) or the sensing of chiral molecules. In the case of metals and semiconductors, the chirality of formed spiral-shaped microstructures depends on the topological charge (TC) of the illuminating optical vortex (OV) beam. The situation is quite different with polarization-sensitive materials such as azopolymers, azobenzene-containing polymers. Azopolymers show polarization-sensitive mass transfer both at the meso and macro levels and have huge potential in diffractive optics and photonics. Previously, only one-spiral patterns formed in thin azopolymer films using circularly polarized OV beams and double-spiral patterns formed using linearly polarized OV beams have been demonstrated. In these cases, the TC of the used OV beams did not affect the number of formed spirals. In this study, we propose to use two-beam (an OV and a Gaussian beam with a spherical wavefront) interference lithography for realization spiral mass transfer with the desired number of formed spirals. The TC of the OV beam allows for controlling the number of formed spirals. We show the microstructures fabricated by the laser processing of thin azopolymer films can be used for the generation of OAM light at the microscale with the desired TC. The experimentally obtained results are in good agreement with the numerically obtained results and demonstrate the potential of the use of such techniques for the laser material processing of polarization-sensitive materials.

Magneto-Thermomechanically Reprogrammable Mechanical Metamaterials

Future active metamaterials for reconfigurable structural applications require fast, untethered, reversible, and reprogrammable (multimodal) transformability with shape locking. Magnetic control has a superior advantage for fast and remotely controlled deployment; however, a significant drawback is needed to maintain the magnetic force to hold the transformation, limiting its use in structural applications. The shape-locking property of shape-memory polymers (SMPs) can resolve this issue. However, the intrinsic irreversibility of SMPs may limit their reconfigurability as active metamaterials. Moreover, to date, reprogrammable methods have required high power with laser and arc welding proving to be energy-inefficient control methods. In this work, a magneto-thermomechanical tool is constructed and demonstrated, which enables a single material system to transform with untethered, reversible, low-powered reprogrammable deformations, and shape locking via the application of magneto-thermomechanically triggered prestress on the SMP and structural instability with asymmetric magnetic torque. The mutual assistance of two physics concepts-magnetic control combined with the thermomechanical behavior of SMPs is demonstrated, without requiring new materials synthesis and high-power energy for reprogramming. This approach can open a new path of active metamaterials, flexible yet stiff soft robots, multimodal morphing structures, and mechanical computing devices where it can be designed in reversible and reprogrammable ways.

Direct Ink Writing: A 3D Printing Technology for Diverse Materials

Additive manufacturing (AM) has gained significant attention due to its ability to drive technological development as a sustainable, flexible, and customizable manufacturing scheme. Among the various AM techniques, direct ink writing (DIW) has emerged as the most versatile 3D printing technique for the broadest range of materials. DIW allows printing of practically any material, as long as the precursor ink can be engineered to demonstrate appropriate rheological behavior. This technique acts as a unique pathway to introduce design freedom, multifunctionality, and stability simultaneously into its printed structures. Here, a comprehensive review of DIW of complex 3D structures from various materials, including polymers, ceramics, glass, cement, graphene, metals, and their combinations through multimaterial printing is presented. The review begins with an overview of the fundamentals of ink rheology, followed by an in-depth discussion of the various methods to tailor the ink for DIW of different classes of materials. Then, the diverse applications of DIW ranging from electronics to food to biomedical industries are discussed. Finally, the current challenges and limitations of this technique are highlighted, followed by its prospects as a guideline toward possible futuristic innovations.

3D Printed Biodegradable Polyurethaneurea Elastomer Recapitulates Skeletal Muscle Structure and Function

Effective skeletal muscle tissue engineering relies on control over the scaffold architecture for providing muscle cells with the required directionality, together with a mechanical property match with the surrounding tissue. Although recent advances in 3D printing fulfill the first requirement, the available synthetic polymers either are too rigid or show unfavorable surface and degradation profiles for the latter. In addition, natural polymers that are generally used as hydrogels lack the required mechanical stability to withstand the forces exerted during muscle contraction. Therefore, one of the most important challenges in the 3D printing of soft and elastic tissues such as skeletal muscle is the limitation of the availability of elastic, durable, and biodegradable biomaterials. Herein, we have synthesized novel, biocompatible and biodegradable, elastomeric, segmented polyurethane and polyurethaneurea (TPU) copolymers which are amenable for 3D printing and show high elasticity, low modulus, controlled biodegradability, and improved wettability, compared to conventional polycaprolactone (PCL) and PCL-based TPUs. The degradation profile of the 3D printed TPU scaffold was in line with the potential tissue integration and scaffold replacement process. Even though TPU attracts macrophages in 2D configuration, its 3D printed form showed limited activated macrophage adhesion and induced muscle-like structure formation by C2C12 mouse myoblasts in vitro, while resulting in a significant increase in muscle regeneration in vivo in a tibialis anterior defect in a rat model. Effective muscle regeneration was confirmed with immunohistochemical assessment as well as evaluation of electrical activity produced by regenerated muscle by EMG analysis and its force generation via a custom-made force transducer. Micro-CT evaluation also revealed production of more muscle-like structures in the case of implantation of cell-laden 3D printed scaffolds. These results demonstrate that matching the tissue properties for a given application via use of tailor-made polymers can substantially contribute to the regenerative outcomes of 3D printed tissue engineering scaffolds.

3D Printing-Enabled Nanoparticle Alignment: A Review of Mechanisms and Applications

3D printing (additive manufacturing (AM)) has enormous potential for rapid tooling and mass production due to its design flexibility and significant reduction of the timeline from design to manufacturing. The current state-of-the-art in 3D printing focuses on material manufacturability and engineering applications. However, there still exists the bottleneck of low printing resolution and processing rates, especially when nanomaterials need tailorable orders at different scales. An interesting phenomenon is the preferential alignment of nanoparticles that enhance material properties. Therefore, this review emphasizes the landscape of nanoparticle alignment in the context of 3D printing. Herein, a brief overview of 3D printing is provided, followed by a comprehensive summary of the 3D printing-enabled nanoparticle alignment in well-established and in-house customized 3D printing mechanisms that can lead to selective deposition and preferential orientation of nanoparticles. Subsequently, it is listed that typical applications that utilized the properties of ordered nanoparticles (e.g., structural composites, heat conductors, chemo-resistive sensors, engineered surfaces, tissue scaffolds, and actuators based on structural and functional property improvement). This review's emphasis is on the particle alignment methodology and the performance of composites incorporating aligned nanoparticles. In the end, significant limitations of current 3D printing techniques are identified together with future perspectives.

Fabricating spatially functionalized 3D-printed scaffolds for osteochondral tissue engineering

Three-dimensional (3D) printing of biodegradable polymers has rapidly become a popular approach to create scaffolds for tissue engineering. This technique enables fabrication of complex architectures and layer-by-layer spatial control of multiple components with high resolution. The resulting scaffolds can also present distinct chemical groups or bioactive cues on the surface to guide cell behavior. However, surface functionalization often includes one or more post-fabrication processing steps, which typically produce biomaterials with homogeneously distributed chemistries that fail to mimic the biochemical organization found in native tissues. As an alternative, our laboratory developed a novel method that combines solvent-cast 3D printing with peptide-polymer conjugates to spatially present multiple biochemical cues in a single scaffold without requiring post-fabrication modification. Here, we describe a detailed, stepwise protocol to fabricate peptide-functionalized scaffolds and characterize their physical architecture and biochemical spatial organization. We used these 3D-printed scaffolds to direct human mesenchymal stem cell differentiation and osteochondral tissue formation by controlling the spatial presentation of cartilage-promoting and bone-promoting peptides. This protocol also describes how to seed scaffolds and evaluate matrix deposition driven by peptide organization.

A disc-chip based high-throughput acute toxicity detection system

Acute toxicity assay presents vital significance in modern environmental monitoring, including online detection and in-situ assay for emergency events. Although photobacteria related detection methods were established and verified in the past decades with combination of photomultiplier tube (PMT), the price and size of PMT sensor hampered application of rapid acute toxicity assay and detection system miniaturization, especially in the resource-limited occasions. Wide application of smartphones with great low-light performance cameras could be used in photobacteria-based toxicity assay instead of the PMT methods. Herein a box-type portable detection system had been successfully established, including a disc-chip for detection, detection device, and smartphones with a high-performance camera. The system performed well showing stable temperature and rotation control. Results captured by CMOS-based camera presented a linear relationship with PMT-based detection method. An image progress algorithm was also established and tested by series diluted zinc sulfate solution as a reference substance. The system also performed well for toxicity analysis for real Atmospheric particle matter sample. The system could be used in some environmental monitoring scenarios as an alternative solution.

Functionalization Strategies and Fabrication of Solvent-Cast PLLA for Bioresorbable Stents

Actual polymer bioresorbable stents (BRS) generate a risk of device thrombosis as a consequence of the incomplete endothelialization after stent implantation. The material-tissue interactions are not fully controlled and stent fabrication techniques do not allow personalized medical solutions. This work investigates the effect of different functionalization strategies onto solvent-cast poly(l-lactic acid) (PLLA) surfaces with the capacity to enhance surface endothelial adhesion and the fabrication of 3D printed BRS. PLLA films were obtained by solvent casting and treated thermally to increase mechanical properties. Surface functionalization was performed by oxygen plasma (OP), sodium hydroxide (SH) etching, or cutinase enzyme (ET) hydrolysis, generating hydroxyl and carboxyl groups. A higher amount of carboxyl and hydroxyl groups was determined on OP and ET compared to the SH surfaces, as determined by contact angle and X-ray photoelectron spectroscopy (XPS). Endothelial cells (ECs) adhesion and spreading was higher on OP and ET functionalized surfaces correlated with the increase of functional groups without affecting the degradation. To verify the feasibility of the approach proposed, 3D printed PLLA BRS stents were produced by the solvent-cast direct writing technique.

Additive Manufacturing of Oral Tablets: Technologies, Materials and Printed Tablets

Additive manufacturing (AM), also known as three-dimensional (3D) printing, enables fabrication of custom-designed and personalized 3D constructs with high complexity in shape and composition. AM has a strong potential to fabricate oral tablets with enhanced customization and complexity as compared to tablets manufactured using conventional approaches. Despite these advantages, AM has not yet become the mainstream manufacturing approach for fabrication of oral solid dosage forms mainly due to limitations of AM technologies and lack of diverse printable drug formulations. In this review, AM of oral tablets are summarized with respect to AM technology. A detailed review of AM methods and materials used for the AM of oral tablets is presented. This article also reviews the challenges in AM of pharmaceutical formulations and potential strategies to overcome these challenges.

Dielectric Spectroscopy and Thermal Properties of Poly(lactic) Acid Reinforced with Carbon-Based Particles: Experimental Study and Design Theory

In the present study, polylactic acid (PLA) enriched with carbonaceous particles like multi-walled carbon nanotubes (MWCNTs), graphene nanoplates (GNPs) or a combination of both up 12 wt % of loading are used for producing 3D-printed specimens with fused deposition modeling (FDM) technology which are then experimentally and theoretically investigated. The goal is to propose a non-conventional filaments indicated for additive manufacturing process with improved dielectric and thermal properties, compared to the performances exhibited by the unfilled polymer. In the light of the above, a wide dielectric spectroscopy and a thermal analysis, supported by a morphological investigation, are performed. The results highlight that the introduction of 1-dimensional filler (MWCNTs) are more suitable for improving the dielectric properties of the resulting materials, due to the enhancement of the interfacial polarization and the presence of functionalized groups, whereas 2-dimensional nanoparticles (GNPs) better favor the thermal conduction mechanisms thanks to the lower thermal boundary resistance between the two phases, polymer/filler. In particular, with a loading of 12 wt % of MWCNTs the relative permittivity reaches the value of 5.35 × 10³ much greater than that of 3.7 measured for unfilled PLA while for the thermal conductivity the enhancement with 12 wt % of GNPs is about 261% respect the thermal behavior of the neat polymer. The experimental results are correlated to theoretical findings, whereas a design of experiment (DoE) approach is adopted for investigating how the different fillers influence the dielectric and thermal performances of the 3D-printed parts, thus assisting the design of such innovative materials that appear promising for development and applications in the electromagnetic (EM) field and heat transfer.

Fabrication and evaluation of a chitin whisker/poly(L-lactide) composite scaffold by the direct trisolvent-ink writing method for bone tissue engineering

Although poly(l-lactide) (PLLA) based porous scaffolds have been widely fabricated through 3D printing, their poor mechanical properties and osteogenic activity still do not meet the needs of bone tissue repair. Herein, chitin whiskers (CHWs), having outstanding mechanical properties, excellent cell affinity, osteogenic activity, etc. were designed to introduce into the PLLA matrix. Moreover, a trisolvent system, including dichloromethane (DCM), 2-butoxyethanlol (2-Bu) and dibutyl phthalate (DBP), instead of a single solvent system of DCM was chosen to prepare CHW/PLLA (CP) composite inks. Then, the CP porous composite scaffolds were further fabricated via the direct ink writing method. The as-printed CP composite scaffolds have good 3D porous structures with a pore size of 400 ± 14 μm and a porosity of 80 ± 5%. Compared with the pure PLLA scaffold, the CP composite scaffolds showed significantly superior hydrophilicity and compression performance, and also were more conducive to cell adhesion, proliferation, and up-regulating alkaline phosphate activity and calcium deposition due to the presence of CHWs. Moreover, these promoting effects of CHWs are positively related to the content of the whiskers in the range of 0-20 wt%. However, as the content of CHWs further increased to 40 wt%, the compression performance, cell affinity and osteogenic activity of the corresponding 40%CP composite scaffold decreased, which may be attributed to the different microstructure of the scaffold from other composite scaffolds. Interestingly, compared with these scaffolds containing a lower mass content of CHWs, only the 40%CP composite scaffold exhibited significant anti-inflammatory properties. These robust CP composite scaffolds offer a new route for bone tissue engineering application.

100th Anniversary of Macromolecular Science Viewpoint: Integrating Chemistry and Engineering to Enable Additive Manufacturing with High-Performance Polymers

Additive manufacturing (AM) with high-performance polymers (HPPs) represents simultaneously one of the most desirable and challenging feats in the AM arena. The very properties that make HPPs so attractive in a broad range of applications also make them nearly impossible to process using common AM equipment. Furthermore, when AM is achieved, it often brings the caveat of compromised mechanical properties of the final parts, in comparison with those made via injection molding. The demand to have advanced fabrication methods, rapid prototyping, and customization of parts while maintaining high performance in the finished products has inspired creative innovations that integrate chemical synthesis, materials science, mechanical engineering, and other fields into a multidisciplinary approach to advance AM with the seemingly "unprintable" HPPs. In this Viewpoint, we summarize several standout developments in the area and offer our perspective on future directions and challenges.

Direct Ink Writing Based 4D Printing of Materials and Their Applications

4D printing has attracted academic interest in the recent years because it endows static printed structures with dynamic properties with the change of time. The shapes, functionalities, or properties of the 4D printed objects could alter under various stimuli such as heat, light, electric, and magnetic field. Briefly, 4D printing is the development of 3D printing with the fourth dimension of time. Among the fabrication techniques that have been employed for 4D printing, the direct ink writing technique shows superiority due to its open source for various types of materials. Herein, the state-of-the-art achievements about the topic of 4D printing through direct ink writing are summarized. The types of materials, printing strategies, actuated methods, and their potential applications are discussed in detail. To date, most efforts have been devoted to shape-shifting materials, including shape memory polymers, hydrogels, and liquid crystal elastomers, showing great prospects in areas ranging from the biomedical field to robotics. Finally, the current challenges and outlook toward 4D printing based on direct ink writing are also pointed out to leave open a significant space for future innovation.

FDM-Based 3D Printing of Polymer and Associated Composite: A Review on Mechanical Properties, Defects and Treatments

Fused deposition modelling (FDM) is one of the fastest-growing additive manufacturing methods used in printing fibre-reinforced composites (FRC). The performances of the resulting printed parts are limited compared to those by other manufacturing methods due to their inherent defects. Hence, the effort to develop treatment methods to overcome these drawbacks has accelerated during the past few years. The main focus of this study is to review the impact of those defects on the mechanical performance of FRC and therefore to discuss the available treatment methods to eliminate or minimize them in order to enhance the functional properties of the printed parts. As FRC is a combination of polymer matrix material and continuous or short reinforcing fibres, this review will thoroughly discuss both thermoplastic polymers and FRCs printed via FDM technology, including the effect of printing parameters such as layer thickness, infill pattern, raster angle and fibre orientation. The most common defects on printed parts, in particular, the void formation, surface roughness and poor bonding between fibre and matrix, are explored. An inclusive discussion on the effectiveness of chemical, laser, heat and ultrasound treatments to minimize these drawbacks is provided by this review.

3D Printed Neural Regeneration Devices

Neural regeneration devices interface with the nervous system and can provide flexibility in material choice, implantation without the need for additional surgeries, and the ability to serve as guides augmented with physical, biological (e.g., cellular), and biochemical functionalities. Given the complexity and challenges associated with neural regeneration, a 3D printing approach to the design and manufacturing of neural devices could provide next-generation opportunities for advanced neural regeneration via the production of anatomically accurate geometries, spatial distributions of cellular components, and incorporation of therapeutic biomolecules. A 3D printing-based approach offers compatibility with 3D scanning, computer modeling, choice of input material, and increasing control over hierarchical integration. Therefore, a 3D printed implantable platform could ultimately be used to prepare novel biomimetic scaffolds and model complex tissue architectures for clinical implants in order to treat neurological diseases and injuries. Further, the flexibility and specificity offered by 3D printed in vitro platforms have the potential to be a significant foundational breakthrough with broad research implications in cell signaling and drug screening for personalized healthcare. This progress report examines recent advances in 3D printing strategies for neural regeneration as well as insight into how these approaches can be improved in future studies.

Three dimensional printed degradable and conductive polymer scaffolds promote chondrogenic differentiation of chondroprogenitor cells

We report a conductive and biodegradable 3D printed polymer scaffold that promotes chondrogenic differentiation of chondroprogenitor cells. The conductive material consists of tetraniline-b-polycaprolactone-b-tetraaniline and polycaprolactone.

3D printing with peptide-polymer conjugates for single-step fabrication of spatially functionalized scaffolds

Biodegradable polymer-based scaffolds are widely used to provide support during early stages of regeneration and can be functionalized with various chemical groups or bioactive cues to promote desired cellular behavior. However, these scaffolds are often modified post-fabrication, which can lead to undesired changes and homogeneously distributed chemistries that fail to mimic the spatial biochemical organization found in native tissues. To address these challenges, surface functionalization can be achieved by 3D printing with pre-functionalized biodegradable polymers, such as peptide-modified polymer conjugates, to control the deposition of preferred chemistries. Peptide-PCL conjugates were synthesized with the canonical cell adhesion peptide motif RGDS or its negative control RGES and 3D printed into scaffolds displaying one or both peptides. The peptides were also modified with bioorthogonal groups, biotin and azide, to visualize peptide concentration and location by labeling with complementary fluorophores. Peptide concentration on the scaffold surface increased with increasing peptide-PCL conjugate concentration added to the ink prior to 3D printing, and scaffolds printed with the highest RGDS(biotin)-PCL concentrations showed a significant increase in NIH3T3 fibroblast adhesion. To demonstrate spatial control of peptide functionalization, multiple printer heads were used to print both peptide-PCL conjugates into the same construct in alternating patterns. Cells preferentially attached and spread on RGDS(biotin)-PCL fibers compared to RGES(azide)-PCL fibers, illustrating how spatial functionalization can be used to influence local cell behavior within a single biomaterial. This presents a versatile platform to generate multifunctional biomaterials that can mimic the biochemical organization found in native tissues to support functional regeneration.

Design and applications of stretchable and self-healable conductors for soft electronics

Soft and conformable electronics are emerging rapidly and is envisioned as the future of next-generation electronic devices where devices can be readily deployed in various environments, such as on-body, on-skin or as a biomedical implant. Modern day electronics require electrical conductors as the fundamental building block for stretchable electronic devices and systems. In this review, we will study the various strategies and methods of designing and fabricating materials which are conductive, stretchable and self-healable, and explore relevant applications such as flexible and stretchable sensors, electrodes and energy harvesters.

Bioprinting with human stem cell-laden alginate-gelatin bioink and bioactive glass for tissue engineering

Three-dimensional (3D) bioprinting technologies have shown great potential in the fabrication of 3D models for different human tissues. Stem cells are an attractive cell source in tissue engineering as they can be directed by material and environmental cues to differentiate into multiple cell types for tissue repair and regeneration. In this study, we investigate the viability of human adipose-derived mesenchymal stem cells (ASCs) in alginate-gelatin (Alg-Gel) hydrogel bioprinted with or without bioactive glass. Highly angiogenic borate bioactive glass (13-93B3) in 50 wt% is added to polycaprolactone (PCL) to fabricate scaffolds using a solvent-based extrusion 3D bioprinting technique. The fabricated scaffolds with 12 × 12 × 1 mm3 in overall dimensions are physically characterized, and the glass dissolution from PCL/glass composite over a period of 28 days is studied. Alg-Gel composite hydrogel is used as a bioink to suspend ASCs, and scaffolds are then bioprinted in different configurations: Bioink only, PCL+bioink, and PCL/glass+bioink, to investigate ASC viability. The results indicate the feasibility of the solvent-based bioprinting process to fabricate 3D cellularized scaffolds with more than 80% viability on day 0. The decrease in viability after 7 days due to glass concentration and static culture conditions is discussed. The feasibility of modifying Alg-Gel with 13-93B3 glass for bioprinting is also investigated, and the results are discussed.

Direct 3D Printing of Hybrid Nanofiber-Based Nanocomposites for Highly Conductive and Shape Memory Applications

Three-dimensional (3D) printing with conductive polymer nanocomposites provides an attractive strategy for the "on-demand" fabrication of electrical devices. This paper demonstrates a family of highly conductive multimaterial composites that can be directly printed into ready-to-use multifunctional electrical devices using a flexible solvent-cast 3D printing technique. The new material design leverages the high aspect ratio and low contact resistance of the hybrid silver-coated carbon nanofibers (Ag@CNFs) with the excellent 3D printability of the thermoplastic polymer. The achieved nanocomposites are capable of printing in open air under ambient conditions, meanwhile presenting a low percolation threshold (i.e., <6 vol %) and high electrical conductivity (i.e., >2.1 × 10⁵ S/m) without any post-treatments. We further find that this hybrid Ag@CNF-based nanocomposite shows a quick and low-voltage-triggered electrical-responsive shape memory behavior, making it a great candidate for printing electroactive devices. Multiple different as-printed Ag@CNF-based highly conductive nanocomposite structures used as high-performance electrical devices (e.g., ambient-printable conductive components, microstructured fiber sensors, flexible and lightweight scaffolds for electromagnetic interference shielding, and low-voltage-triggered smart grippers) are successfully demonstrated herein. This simple additive manufacturing approach combined with the synergic effects of the multimaterial nanocomposite paves new ways for further development of advanced and smart electrical devices in areas of soft robotics, sensors, wearable electronics, etc.

Downstream Processing Technologies/Capturing and Final Purification : Opportunities for Innovation, Change, and Improvement. A Review of Downstream Processing Developments in Protein Purification

Increased pressure on upstream processes to maximize productivity has been crowned with great success, although at the cost of shifting the bottleneck to purification. As drivers were economical, focus is on now on debottlenecking downstream processes as the main drivers of high manufacturing cost. Devising a holistically efficient and economical process remains a key challenge. Traditional and emerging protein purification strategies with particular emphasis on methodologies implemented for the production of recombinant proteins of biopharmaceutical importance are reviewed. The breadth of innovation is addressed, as well as the challenges the industry faces today, with an eye to remaining impartial, fair, and balanced. In addition, the scope encompasses both chromatographic and non-chromatographic separations directed at the purification of proteins, with a strong emphasis on antibodies. Complete solutions such as integrated USP/DSP strategies (i.e., continuous processing) are discussed as well as gains in data quantity and quality arising from automation and high-throughput screening (HTS). Best practices and advantages through design of experiments (DOE) to access a complex design space such as multi-modal chromatography are reviewed with an outlook on potential future trends. A discussion of single-use technology, its impact and opportunities for further growth, and the exciting developments in modeling and simulation of DSP rounds out the overview. Lastly, emerging trends such as 3D printing and nanotechnology are covered. Graphical Abstract Workflow of high-throughput screening, design of experiments, and high-throughput analytics to understand design space and design space boundaries quickly. (Reproduced with permission from Gregory Barker, Process Development, Bristol-Myers Squibb).

Materials and Structures toward Soft Electronics

Soft electronics are intensively studied as the integration of electronics with dynamic nonplanar surfaces has become necessary. Here, a discussion of the strategies in materials innovation and structural design to build soft electronic devices and systems is provided. For each strategy, the presentation focuses on the fundamental materials science and mechanics, and example device applications are highlighted where possible. Finally, perspectives on the key challenges and future directions of this field are presented.

Morphological, Rheological and Electromagnetic Properties of Nanocarbon/Poly(lactic) Acid for 3D Printing: Solution Blending vs. Melt Mixing

The limitation of poor mechanical stability and difficulties in printing electrically conductive components can be overcome owing to the recent introduction of nanotechnology into the field of additive manufacturing (AM) and the consequent development of nonconventional polymer nanocomposites suitable for 3D printing. In the present work, different weight percentages (up to 6 wt % in total) of carbon-based nanostructures-multiwalled carbon nanotubes (MWCNTs), graphene nanoplatelets (GNPs), and a combination of both fillers (MWCNTs/GNPs)-were incorporated into poly(lactic) acid (PLA, Ingeo™) in an attempt to overcome several limitations of conventional 3D manufacturing based on insulating materials. Solution blending and melt mixing were the two fabrication methods adopted for preparation of the samples under test. A comparison of the morphological, rheological, and electrical properties of the resulting nanocomposites was carried out. Moreover, for the same weight concentrations, the influence of physical and geometrical features (i.e., functionalization and aspect ratio) of the embedded fillers was also investigated. Rheological methods were applied to control the quality of fillers dispersion in PLA matrix. The rheological percolation threshold was considered as reference in order to evaluate the internal structure of nanodispersions. TEM visualization, combined with rheological characterizations, was used for efficient control of the nanofiller dispersion. DC characterization revealed that lower electrical percolation thresholds and higher values of electrical conductivity were achieved using fillers with a larger aspect ratio and melt mixing, respectively. Moreover, given the possibility of obtaining complex and appropriate shapes for electromagnetic compatibility (EC) applications, electromagnetic (EM) response of the nanocomposites at the highest filler concentration was investigated in GHz and THz regions. It was found that the electromagnetic shielding efficiency (EMI) of nanocomposites strongly depended on the aspect ratio of the nanofillers, whereas the type of processing technique did not have a significant effect. Therefore, a careful choice of methods and materials must be made to address the final application for which these materials and further 3D printed architectures are designed.

Printed Nanocomposite Energy Harvesters with Controlled Alignment of Barium Titanate Nanowires

Piezoelectric nanocomposites are commonly used in the development of self-powered miniaturized electronic devices and sensors. Although the incorporation of one-dimensional (1D) piezoelectric nanomaterials (i.e., nanowires, nanorods, and nanofibers) in a polymer matrix has led to the development of devices with promising energy harvesting and sensing performance, they have not yet reached their ultimate performance due to the challenges in fabrication. Here, a direct-write additive manufacturing technique is utilized to facilitate the fabrication of spatially tailored piezoelectric nanocomposites. High aspect ratio barium titanate (BaTiO₃) nanowires (NWs) are dispersed in a polylactic acid (PLA) solution to produce a printable piezoelectric solution. The BaTiO₃ NWs are arranged in PLA along three different axes of alignment via shear-induced alignment during a controlled printing process. The result of electromechanical characterizations shows that the nanowire alignment significantly affects the energy harvesting performance of the nanocomposites. The optimal power output can be enhanced by as much as eight times for printed nanocomposites with a tailored architecture of the embedded nanostructures. This power generation capacity is 273% higher compared to conventional cast nanocomposites with randomly oriented NWs. The findings of this study suggest that 3D printing of nanowire-based nanocomposites is a feasible, scalable, and rapid methodology to produce high-performance piezoelectric transducers with tailored micro- and nanostructures. This study offers the first demonstration of nanocomposite energy harvesters with spatially controlled filler orientation realized directly from a digital design.

Ultraviolet-Assisted Direct Ink Write to Additively Manufacture All-Aromatic Polyimides

All-aromatic polyimides have degradation temperatures above 500 °C, excellent mechanical strength, and chemical resistance, and are thus ideal polymers for high-temperature applications. However, their all-aromatic structure impedes additive manufacturing (AM) because of the lack of melt processability and insolubility in organic solvents. Recently, our group demonstrated the design of UV-curable polyamic acids (PAA), the precursor of polyimides, to enable their processing using vat photopolymerization AM. This work leverages our previous synthetic strategy and combines it with the high solution viscosity of nonisolated PAA to yield suitable UV-curable inks for UV-assisted direct ink write (UV-DIW). UV-DIW enabled the design of complex three-dimensional structures comprising of thin features, such as truss structures. Dynamic mechanical analysis of printed and imidized specimens confirmed the thermomechanical properties typical of all-aromatic polyimides, showing a storage modulus above 1 GPa up to 400 °C. Processing polyimide precursors via DIW presents opportunity for multimaterial printing of multifunctional components, such as three-dimensional integrated electronics.