An Investigation of PS-b-PEO Polymersomes for the Oral Treatment and Diagnosis of Hyperammonemia

Portable Near-Infrared Fluorometer for a Liposomal Blood Lactate Assay

In sepsis, plasma lactate is a key biomarker of disease severity, prognosis, and treatment success. However, the median time to result for clinical lactate tests is 3 h. We recently reported a near-infrared fluorescent (NIRF) blood lactate assay that relies on a two-step enzymatic reaction in a liposomal reaction compartment. This assay was optimized in human blood and was capable of quantifying lactate in fresh capillary blood from human volunteers at clinically relevant concentrations in 2 min. However, these studies were performed with a tabletop fluorescence plate reader. For translation to the point of care, the liposomal lactate assay needs to be combined with a small portable NIR fluorometer. Portable NIR fluorometers were successfully used for the analysis of skin and soil samples, but reports for blood metabolite assays are scarce. We aimed at testing the performance of the liposomal lactate assay in combination with a commercial small portable NIR fluorometer. First, we tested the fluorophore of the liposomal lactate assay using the NIR dye sulfo-cyanine 7; we observed strong fluorescence signals and high linearity. Second, we performed the liposomal lactate assay in lactate-spiked human arterial blood using the portable fluorometer as the detector and observed strong and highly linear lactate sensing at clinically relevant lactate concentrations after 2 min. Finally, spiking fresh mouse blood with three clinically relevant lactate concentrations led to a significantly different response to all three concentrations after 5 min. These results highlight the usefulness of the tested portable NIR fluorometer for the liposomal lactate assay and motivate a clinical evaluation of this rapid and easy-to-use lactate assay.

Vesicular Diagnostics: A Spotlight on Lactate- and Ammonia-Sensing Systems

Liposomes are a highly successful drug delivery system with over 15 FDA-approved formulations. Beyond delivering drugs, lipid and polymer vesicles have successfully been used for diagnostic applications. These applications range from more traditional uses, such as releasing diagnostic agents in a controlled manner, to leveraging the unique membrane properties to separate analytes and provide isolated reaction compartments in complex biological matrices. In this Spotlight on Applications, I highlight the complexities in the development and translation of diagnostic vesicles with two case studies, a liposomal reaction compartment for lactate sensing and a transmembrane pH-gradient polymersome for ammonia sensing.

Next-Generation Diagnostic Wound Dressings for Diabetic Wounds

Chronic lower extremity wounds (diabetic foot ulcers) are a serious and prevalent complication of diabetes. These wounds exhibit low healing rates and present a high risk of amputation. Current diagnostic options for foot ulcers are limited to macroscopic wound analysis such as wound depth, implicated tissues, and infection. Molecular diagnostics promises to improve foot ulcer diagnosis, staging, and assessment of the treatment response. In this perspective, we report recent progress in understanding the pathophysiology of diabetic wound healing and point to recently emerged novel molecular targets for wound diagnostics. We discuss selected diagnostic wound dressings under preclinical development that detect one or several inflammatory markers, bacterial secretions, hyperglycemia, and mechanical stress. We also highlight key translational challenges of investigational diagnostic bandages for diabetic foot ulcers.

Current Perspectives on Synthetic Compartments for Biomedical Applications

Nano- and micrometer-sized compartments composed of synthetic polymers are designed to mimic spatial and temporal divisions found in nature. Self-assembly of polymers into compartments such as polymersomes, giant unilamellar vesicles (GUVs), layer-by-layer (LbL) capsules, capsosomes, or polyion complex vesicles (PICsomes) allows for the separation of defined environments from the exterior. These compartments can be further engineered through the incorporation of (bio)molecules within the lumen or into the membrane, while the membrane can be decorated with functional moieties to produce catalytic compartments with defined structures and functions. Nanometer-sized compartments are used for imaging, theranostic, and therapeutic applications as a more mechanically stable alternative to liposomes, and through the encapsulation of catalytic molecules, i.e., enzymes, catalytic compartments can localize and act in vivo. On the micrometer scale, such biohybrid systems are used to encapsulate model proteins and form multicompartmentalized structures through the combination of multiple compartments, reaching closer to the creation of artificial organelles and cells. Significant progress in therapeutic applications and modeling strategies has been achieved through both the creation of polymers with tailored properties and functionalizations and novel techniques for their assembly.

Recent Trends in Advanced Photoinitiators for Vat Photopolymerization 3D Printing

3D printing has revolutionized the way of manufacturing with a huge impact on various fields, in particular biomedicine. Vat photopolymerization-based 3D printing techniques such as stereolithography (SLA) and digital light processing (DLP) attracted considerable attention owing to their superior print resolution, relatively high speed, low cost and flexibility in resin material design. As one key element of the SLA/DLP resin, photoinitiators or photoinitiating systems have experienced significant development in recent years, in parallel with the exploration of 3D printing (macro)monomers. The design of new photoinitiating systems can not only offer faster 3D printing speed and enable low-energy visible light fabrication, but also can bring new functions to the 3D printed products and even generate new printing methods in combination with advanced optics. This review evaluates recent trends in the development and application of advanced photoinitiators and photoinitiating systems for vat photopolymerization 3D printing, with a wide range of small molecules, polymers and nanoassemblies involved. Personal perspectives on the current limitations and future directions are eventually provided. This article is protected by copyright. All rights reserved.

Polymersomes: Soft Nanoparticles from Miktoarm Stars for Applications in Drug Delivery

Self-assembly of amphiphilic macromolecules has provided an advantageous platform to address significant issues in a variety of areas, including biology. Such soft nanoparticles with a hydrophobic core and hydrophilic corona, referred to as micelles, have been extensively investigated for delivering lipophilic therapeutics by physical encapsulation. Polymeric vesicles or polymersomes with similarities in morphology to liposomes continue to play an essential role in understanding the behavior of cell membranes and, in addition, have offered opportunities in designing smart nanoformulations. With the evolution in synthetic methodologies to macromolecular precursors, the construction of such assemblies can now be modulated to tailor their properties to match desired needs. This review brings into focus the current state-of-the-art in the design of polymersomes using amphiphilic miktoarm star polymers through a detailed analysis of the synthesis of miktoarm star polymers with tuned lengths of varied polymeric arms, their self-assembly, and applications in drug delivery.

Optimization of an ammonia assay based on transmembrane pH-gradient polymersomes

Reliable ammonia quantification assays are essential for monitoring ammonemia in patients with liver diseases. In this study, we describe the development process of a microplate-based assay for accurate, precise, and robust ammonia quantification in biological fluids, following regulatory guidelines on bioanalytical method validation. The assay is based on transmembrane pH-gradient polymersomes that encapsulate a pH-sensitive ratiometric fluorophore, the fluorescence signal of which correlates with the ammonia concentration in the sample. Using a four-parameter logistic regression, the assay had a large quantification range (30–800 μM ammonia). As for selectivity, the presence of amino acids or pyruvate (up to clinically relevant concentrations) showed no assay interference. In samples with low bilirubin levels, polymersomes containing the fluorophore pyranine provided accurate ammonia quantification. In samples with high bilirubin concentrations, billirubin’s optical interference was alleviated when replacing pyranine with a close to near-infrared hemicyanine fluorophore. Finally, the assay could correctly retrieve the ammonia concentration in ammonia-spiked human plasma samples, which was confirmed by comparing our measurements with the data obtained using a commercially available point-of-care device for ammonia.

Just add water: hydratable, morphologically diverse nanocarrier powders for targeted delivery

Two major obstacles that limit the widespread usage of polymeric nanocarriers include the complexity of formulation methods and their stability during storage. To address both of these issues, here we present morphologically complex nanocarriers in a hydratable powder form, which bypasses the need for expensive, harsh, and/or time-consuming nanocarrier fabrication techniques. The powders are composed of carbohydrates and self-assembling polymer amphiphiles having a low glass transition temperature. Hydration requires less than one minute and only involves the addition of aqueous media (water or saline) to rapidly obtain self-assembled micelles, worm-like micelles (i.e. filomicelles), or polymersomes from poly(ethylene glycol)-b-poly(propylene sulfide) (PEG-b-PPS) polymers. The formulated powders are highly stable, achieving hydration into monodisperse nanocarriers following >6 months of storage. Diverse drug cargoes were efficiently encapsulated during hydration, including hydrophobic small molecules for micellar morphologies, as well as individual and concurrent loading of both hydrophobic and hydrophilic molecules for vesicular morphologies. Hydrated polymersomes are shown to load hydrophilic biological macromolecules, and encapsulated enzymes retain bioactivity. Furthermore, we demonstrate that inclusion of lipid-anchored ligands in powder form permits the surface-display of targeting ligands and enhances target cell uptake, thereby extending this technology to targeted drug delivery applications. Our powder-based formulation strategy was extendable to commercially available polymer amphiphiles, including PEG-b-polystyrene and PEG-b-polycaprolactone. The formulated nanotechnologies described herein are highly modular, require minimal preparation, and remain stable in ambient long-term storage (bypassing cold chain requirements), which will enable their use in medicine (human and veterinary), research, and commercial applications from cosmetics to agriculture.

pH-Responsive nanocomposite fibres allowing MRI monitoring of drug release

Magnetic resonance imaging (MRI) is one of the most widely-used non-invasive clinical imaging tools, producing detailed anatomical images whilst avoiding side effects such as trauma or X-ray radiation exposure. In this article, a new approach to non-invasive monitoring of drug release from a delivery vehicle via MRI was developed, using pH-responsive Eudragit L100 and S100 fibres encapsulating superparamagnetic iron oxide nanoparticles (SPIONs) and carmofur (a drug used in the treatment of colon cancer). Fibres were prepared by electrospinning, and found to be smooth and cylindrical with diameters of 645 ± 225 nm for L100 and 454 ± 133 nm for S100. The fibres exhibited pH responsive dissolution behaviour. Around the physiological pH range, clear pH-responsive proton relaxation rate changes due to matrix swelling/dissolution can be observed: r2 values of L100 fibres increase from 29.3 ± 8.3 to 69.8 ± 2.5 mM-1 s-1 over 3 h immersion in a pH 7.4 medium, and from 13.5 ± 2.0 mM-1 s-1 to 42.1 ± 3.0 mM-1 s-1 at pH 6.5. The r2 values of S100 fibres grow from 30.4 ± 4.4 to 64.7 ± 1.0 mM-1 s-1 at pH 7.4, but at pH 6.5, where the S100 fibres are not soluble, r2 remains very low (< 4 mM-1 s-1). These dramatic changes in relaxivity demonstrate that pH-responsive dissolution results in SPION release. In vitro drug release studies showed the formulations gave rapid release of carmofur at physiological pH values (pH 6.5 and 7.4), and acid stability studies revealed that they can protect the SPIONs from digestion in acid environments, giving the fibres potential for oral administration. Exploration of the relationship between relaxivity and carmofur release suggests a linear correlation (R2 > 0.94) between the two. Mathematical equations were developed to predict carmofur release in vitro, with very similar experimental and predicted release profiles obtained. Therefore, the formulations developed herein have the potential to be used for non-invasive monitoring of drug release in vivo, and could ultimately result in dramatic reductions to off-target side effects from interventions such as chemotherapy.

Factors affecting the morphology of some organic and inorganic nanostructures for drug delivery: characterization, modifications, and toxicological perspectives

Introduction: In this review, we aim to highlight the impact of various processes and formulation variables influencing the characteristics of certain surfactant-based nanoconstructs for drug delivery. Areas covered: The review includes the discussion on processing parameters for the preparation of nanoconstructs, especially those made up of surfactants. Articles published in last 15 years (437) were reviewed, 381 articles were selected for data review and most appropriate articles (215) were included in article. Effect of variables such as surfactant concentration and type, membrane additives, temperature, and pH-dependent transitions on morphology has been highlighted along with effect of shape on nanoparticle uptake by cells. Various characterization techniques explored for these nanostructures with respect to size, morphology, lamellarity, distribution, etc., and a separate section on polymeric vesicles and the influence of block copolymers, type of block copolymer, control of block length, interaction of multiple block copolymers on the structure of polymersomes and chimeric nanostructures have been discussed. Finally, applications, modification, degradation, and toxicological aspects of these drug delivery systems have been highlighted. Expert opinion: Parameters influencing the morphology of micelles and vesicles can directly or indirectly affect the efficacy of small molecule cellular internalization as well as uptake in the case of biologicals.[Figure: see text].

Preclinical evaluation of liposome-supported peritoneal dialysis for the treatment of hyperammonemic crises

Liposome-supported peritoneal dialysis (LSPD) with transmembrane pH-gradient liposomes was previously shown to enhance ammonia removal in cirrhotic rats and holds promise for the treatment of hyperammonemic crises-associated disorders. The main objective of this work was to conduct the preclinical evaluation of LSPD in terms of pharmacokinetics, ammonia uptake, and toxicology to seek regulatory approval for a first-in-human study. The formulation containing citric acid-loaded liposomes was administered intraperitoneally at two different doses once daily for ten days to healthy minipigs. It was also tested in a domestic pig model of hyperammonemia. The pharmacokinetics of citric acid and 1,2-dipalmitoyl-sn-glycero-3-phosphocholine was linear following intraperitoneal administration of medium and high dose. There was no systemic accumulation following daily doses over ten days. The systemic exposure to phospholipids remained low. Furthermore, the liposome-containing peritoneal fluid contained significantly higher ammonia levels than the liposome-free control, demonstrating efficient ammonia sequestration in the peritoneal space. This was indeed confirmed by the ability of LSPD to decrease plasmatic ammonia levels in artificially induced hyperammonemic pigs. LSPD was well tolerated, and no complement activation-related pseudoallergy reactions were observed. The safety profile, the linear pharmacokinetics of citric acid following repeated administrations of LSPD as well as the linear dose-dependent ammonia sequestration in the peritoneal space provide a strong basis for the clinical investigation of LSPD.

Periphery-confined particulate systems for the management of neurodegenerative diseases and toxicity: Avoiding the blood-brain-barrier challenge

The blood-brain barrier prevents passage of large and hydrophilic molecules, undermining efforts to deliver most active molecules, proteins and other macromolecules. To date, nanoparticle-assisted delivery has been extensively studied to overcome this challenge but with limited success. On the other hand, for certain brain therapeutic applications, periphery-confined particles could be of immediate therapeutic usefulness. The modulation of CNS dysfunctions from the peripheral compartment is a promising approach, as it does not involve invasive interventions. From recent studies, three main roles could be identified for periphery-confined particles: brain tissue detoxification via the "sink-effect"; a "circulating drug-reservoir" effect to improve drug delivery to brain tissues, and finally, brain vascular endothelium targeting to diagnose or heal vascular-related dysfunctions. These applications are much easier to implement as they do not involve complex therapeutic and targeting strategies and do not require crossing biological barriers. Micro/nano-devices required for such applications will likely be simpler to synthesize and will involve fewer complex materials. Moreover, peripheral particles are expected to be less prone to neurotoxicity and issues related to their diffusion in confined space.

Emerging era of “somes”: polymersomes as versatile drug delivery carrier for cancer diagnostics and therapy

Over the past two decades, polymersomes have been widely investigated for the delivery of diagnostic and therapeutic agents in cancer therapy. Polymersomes are stable polymeric vesicles, which are prepared using amphiphilic block polymers of different molecular weights. The use of high molecular weight amphiphilic copolymers allows for possible manipulation of membrane characteristics, which in turn enhances the efficiency of drug delivery. Polymersomes are more stable in comparison with liposomes and show less toxicity in vivo. Furthermore, their ability to encapsulate both hydrophilic and hydrophobic drugs, significant biocompatibility, robustness, high colloidal stability, and simple methods for ligands conjugation make polymersomes a promising candidate for therapeutic drug delivery in cancer therapy. This review is focused on current development in the application of polymersomes for cancer therapy and diagnosis. Graphical abstract.

Near-Infrared Fluorescence Hydrogen Peroxide Assay for Versatile Metabolite Biosensing in Whole Blood

In emergency medicine, blood lactate levels are commonly measured to assess the severity and response to treatment of hypoperfusion-related diseases (e.g., sepsis, trauma, cardiac arrest). Clinical blood lactate testing is conducted with laboratory analyzers, leading to a delay of 3 h between triage and lactate result. Here, a fluorescence-based blood lactate assay, which can be utilized for bedside testing, based on measuring the hydrogen peroxide generated by the enzymatic oxidation of lactate is described. To establish a hydrogen peroxide assay, near-infrared cyanine derivatives are screened and sulfo-cyanine 7 is identified as a new horseradish peroxidase (HRP) substrate, which loses its fluorescence in presence of HRP and hydrogen peroxide. As hydrogen peroxide is rapidly cleared by erythrocytic catalase and glutathione peroxidase, sulfo-cyanine 7, HRP, and lactate oxidase are encapsulated in a liposomal reaction compartment. In lactate-spiked bovine whole blood, the newly developed lactate assay exhibits a linear response in a clinically relevant range after 10 min. Substituting lactate oxidase with glucose and alcohol oxidase allows for blood glucose, ethanol, and methanol biosensing, respectively. This easy-to-use, rapid, and versatile assay may be useful for the quantification of a variety of enzymatically oxidizable metabolites, drugs, and toxic substances in blood and potentially other biological fluids.

Engineered Polymersomes for the Treatment of Fish Odor Syndrome: A First Randomized Double Blind Olfactory Study

Trimethylamine (TMA) is a metabolite overtly present in patients suffering from trimethylaminuria (TMAU), a rare genetic disorder characterized by a strong "fishy" body odor. To date, no approved pharmacological treatment to sequester excess TMA on the skin of patients exists. Here, transmembrane pH gradient poly(isoprene)-block-poly(ethylene glycol) (PI-b-PEG) polymersomes are investigated for the topical removal of TMA. PI-b-PEG amphiphiles of varying chain length are synthesized and evaluated for their ability to form vesicular structures in aqueous media. The optimization of the PI/PEG ratio of transmembrane pH gradient polymersomes allows for the rapid and efficient capture of TMA both in solution and after incorporation into a topical hydrogel matrix at the pH of the skin. A subsequent double blind olfactory study reveals a significant decrease in perceived odor intensity after application of the polymersome-based formulation on artificial skin substrates that has been incubated in TMA-containing medium. This simple and novel approach has the potential to ease the burden of people suffering from TMAU.

Ammonia uptake by transmembrane pH gradient poly(isoprene)-block-poly(ethylene glycol) polymersomes

Transmembrane pH gradient poly(isoprene)-block-poly(ethylene glycol) (PI-b-PEG) polymersomes were investigated for their potential use in the detoxification of ammonia, a metabolite that is excessively present in patients suffering from urea cycle disorders and advanced liver diseases, and which causes neurotoxic effects (e.g., hepatic encephalopathy). Polymers varying in PI and PEG block length were synthesized via nitroxide-mediated polymerization and screened for their ability to self-assemble into polymersomes in aqueous media. Ammonia sequestration by the polymersomes was investigated in vitro. While most vesicular systems were able to capture ammonia in simulated intestinal fluids, uptake was lost in partially dehydrated medium mimicking conditions in the colon. Polymeric crosslinking of residual olefinic bonds in the PI block increased polymersome stability, partially preserving the ammonia capture capacity in the simulated colon environment. These more stable vesicular systems hold promise for the chronic oral treatment of hyperammonemia.

Fluorescent chemosensors based on conjugated polymers with N-heterocyclic moieties: two decades of progress

A brief summary of representative fluorescent chemosensors based on conjugated polymers with N-heterocyclic moieties, followed by a discussion on the limitations and challenges of current systems, as well as possible future research directions.