Two-color multiplexed analysis of eight short tandem repeat loci with an electrophoretic microdevice

Two-Color Capillary Electrophoresis with On-Column Excitation and Wave-Guide Based Fluorescent Detection

An optical wave-guide based two-color capillary electrophoresis laser induced fluorescence (CE-LIF) instrument is described. The wave-guide based approach allows for on column excitation and detection with two-color discrimination. The instrument is designed to allow either electrokinetic or hydrodynamic injections. In its present configuration, the attainable limit of detection (LOD, S/N = 3) was 50 × 10−21 moles of fluorescein with a 488-nm excitation source. This study was designed to test the instrument design for applications in protein analyses. Fluorescent dyes with two different wavelengths were simultaneously separated and detected as were complexes formed by labeled antibodies to NF'B p65 and cdc2p34. Quantification of both proteins in THP-1 cell lysates performed using this approach illustrates a rapid screening application of this instrument.

DNA mutation detection and analysis using miniaturized microfluidic systems

Identification of genetic sequence variations occurring on a population-wide scale is key to unraveling the complex interactions that are the underlying cause of many medical disorders and diseases. A critical need exists, however, for advanced technology to enable DNA mutation analysis to be performed with significantly higher throughput and at significantly lower cost than is currently attainable. Microfluidic systems offer an attractive platform to address these needs by combining the ability to perform rapid analysis with a simplified device format that can be inexpensively mass-produced. This paper will review recent progress toward developing these next-generation systems and discuss challenges associated with adapting these technologies for routine laboratory use.

Disposable polyester-toner electrophoresis microchips for DNA analysis

Microchip electrophoresis has become a powerful tool for DNA separation, offering all of the advantages typically associated with miniaturized techniques: high speed, high resolution, ease of automation, and great versatility for both routine and research applications. Various substrate materials have been used to produce microchips for DNA separations, including conventional (glass, silicon, and quartz) and alternative (polymers) platforms. In this study, we perform DNA separation in a simple and low-cost polyester-toner (PeT)-based electrophoresis microchip. PeT devices were fabricated by a direct-printing process using a 600 dpi-resolution laser printer. DNA separations were performed on PeT chip with channels filled with polymer solutions (0.5% m/v hydroxyethylcellulose or hydroxypropylcellulose) at electric fields ranging from 100 to 300 V cm(-1). Separation of DNA fragments between 100 and 1000 bp, with good correlation of the size of DNA fragments and mobility, was achieved in this system. Although the mobility increased with increasing electric field, separations showed the same profile regardless of the electric field. The system provided good separation efficiency (215,000 plates per m for the 500 bp fragment) and the separation was completed in 4 min for 1000 bp fragment ladder. The cost of a given chip is approximately $0.15 and it takes less than 10 minutes to prepare a single device.

A valveless microfluidic device for integrated solid phase extraction and polymerase chain reaction for short tandem repeat (STR) analysis

A valveless microdevice has been developed for the integration of solid phase extraction (SPE) and polymerase chain reaction (PCR) on a single chip for the short tandem repeat (STR) analysis of DNA from a biological sample. The device consists of two domains--a SPE domain filled with silica beads as a solid phase and a PCR domain with an ~500 nL reaction chamber. DNA from buccal swabs was purified and amplified using the integrated device and a full STR profile (16 loci) resulted. The 16 loci Identifiler® multiplex amplification was performed using a non-contact infrared (IR)-mediated PCR system built in-house, after syringe-driven SPE, providing an ~80-fold and 2.2-fold reduction in sample and reagent volumes consumed, respectively, as well as an ~5-fold reduction in the overall analysis time in comparison to conventional analysis. Results indicate that the SPE-PCR system can be used for many applications requiring genetic analysis, and the future addition of microchip electrophoresis (ME) to the system would allow for the complete processing of biological samples for forensic STR analysis on a single microdevice.

Genotyping of IRGM tetranucleotide promoter oligorepeats by fluorescence resonance energy transfer

Fluorescence resonance energy transfer (FRET) genotyping has been well established for the rapid assessment of single nucleotide polymorphisms (SNPs) and deletions. A design is presented that allows the typing of short tandem oligo repeat sequences using the LightTyper/LightCycler system. The protocol was evaluated and applied to the typing of a tetranucleotide promoter repeat of the human gene encoding the immunity-related GTPase family, M (IRGM) molecule in >2000 individuals from Ghana, West Africa.

AOTF-based multicolor fluorescence detection for short tandem repeat (STR) analysis in an electrophoretic microdevice

An acousto-optic tunable filter (AOTF) has been used to perform multicolor fluorescence detection for four and five-color short tandem repeat (STR) analysis on glass microchips. Matrix files were initially generated by collecting and comparing the laser-induced fluorescence emission of the labels specific to a particular STR kit, and raw data was processed to remove spectral overlap. The AmpFlSTR kits used in this work include Profiler Plus and COfiler, which are four-color kits used in tandem to address the core STR loci, as well as the five-color Identifiler kit, which contains each of the loci. In contrast to previous reports on multicolor detection for STR analysis on microchips, this detection system is characterized by a single filter and detector, and reports the first five-color genotyping application on-chip. This capability matches the portability and reduced scale of the microchip with the state-of-the-art in multicolor STR analysis kits.

High-resolution DNA melting analysis for simple and efficient molecular diagnostics

High-resolution melting of DNA is a simple solution for genotyping, mutation scanning and sequence matching. The melting profile of a PCR product depends on its GC content, length, sequence and heterozygosity and is best monitored with saturating dyes that fluoresce in the presence of double-stranded DNA. Genotyping of most variants is possible by the melting temperature of the PCR products, while all variants can be genotyped with unlabeled probes. Mutation scanning and sequence matching depend on sequence differences that result in heteroduplexes that change the shape of the melting curve. High-resolution DNA melting has several advantages over other genotyping and scanning methods, including an inexpensive closed tube format that is homogenous, accurate and rapid. Owing to its simplicity and speed, the method is a good fit for personalized medicine as a rapid, inexpensive method to predict therapeutic response.

High resolution DNA separations using microchip electrophoresis

Planar microfluidic devices have emerged as effective tools for the electrophoretic separation of a variety of different DNA inputs. The advancement of this miniaturized platform was inspired initially by demands placed on electrophoretic performance metrics by the human genome project and has provided a viable alternative to slab gel and even capillary formats due to its ability to offer high resolution separations of nucleic acid materials in a fraction of the time associated with its predecessors, consumption of substantially less sample and reagents while maintaining the ability to perform many separations in parallel for realizing ultra-high throughputs. Another compelling advantage of this separation platform is that it offers the potential for integrating front-end sample preprocessing steps onto the separation device eliminating the need for manual sample handling. This review aims to compile a recent survey of various electrophoretic separations using either glass or polymer-based microchips in the areas of genotyping and DNA sequencing as well as those involving the growing field of DNA-based forensics.

Forensic DNA Analysis on Microfluidic Devices: A Review

The advent of microfluidic technology for genetic analysis has begun to impact forensic science. Recent advances in microfluidic separation of short-tandem-repeat (STR) fragments has provided unprecedented potential for improving speed and efficiency of DNA typing. In addition, the analytical processes associated with sample preparation--which include cell sorting, DNA extraction, DNA quantitation, and DNA amplification--can all be integrated with the STR separation in a seamless manner. The current state of these microfluidic methods as well as their advantages and potential shortcomings are detailed. Recent advances in microfluidic device technology, as they pertain to forensic DNA typing, are discussed with a focus on the forensic community.

Usefulness of microchip electrophoresis for the analysis of mitochondrial DNA in forensic and ancient DNA studies

We evaluate the usefulness of a commercially available microchip CE (MCE) device in different genetic identification studies performed with mitochondrial DNA (mtDNA) targets, including the haplotype analysis of HVR1 and HVR2 and the study of interspecies diversity of cytochrome b (Cyt b) and 16S ribosomal RNA (16S rRNA) mitochondrial genes in forensic and ancient DNA samples. The MCE commercial system tested in this study proved to be a fast and sensitive detection method of length heteroplasmy in cytosine stretches produced by 16 189T>C transitions in HVR1 and by 309.1 and 309.2 C-insertions in HVR2. Moreover, the quantitative analysis of PCR amplicons performed by LIF allowed normalizing the amplicon input in the sequencing reactions, improving the overall quality of sequence data. These quantitative data in combination with the quantification of genomic mtDNA by real-time PCR has been successfully used to evaluate the PCR efficiency and detection limit of full sequencing methods of different mtDNA targets. The quantification of amplicons also provided a method for the rapid evaluation of PCR efficiency of multiplex-PCR versus singleplex-PCR to amplify short HV1 amplicons (around 100 bp) from severely degraded ancient DNA samples. The combination of human-specific (Cyt b) and universal (16S rRNA) mtDNA primer sets in a single PCR reaction followed by MCE detection offers a very rapid and simple screening test to differentiate between human and nonhuman hair forensic samples. This method was also very efficient with degraded DNA templates from forensic hair and bone samples, because of its applicability to detect small amplicon sizes. Future possibilities of MCE in forensic DNA typing, including nuclear STRs and SNP profiling are suggested.

Multicolor Fluorescence Detection on an Electrophoretic Microdevice Using an Acoustooptic Tunable Filter

An acoustooptic tunable filter (AOTF) is used to detect multiple fluorescent signals on a fluidic microdevice. A confocal laser-induced fluorescence detection setup is used to excite fluorescent dyes in glass microchannels, presenting a streamlined and robust detection system consisting of the narrow-bandwidth AO filter and a single photodetector. The flexibility of the filter is demonstrated by alternating between wavelengths for precise microchannel alignment and sweeping through a range of wavelengths for preliminary spectral characterization of subnanoliter probe volumes of target analytes. The AOTF is also coupled with an electrophoretic separation for the multicolor detection of PCR-amplified DNA against a labeled sizing standard, the discrimination of multiple amplicons overlapped in time, and the identification of amplified biowarfare agents in a fluorescent spiking experiment. Finally, to demonstrate the multicolor capability of the system, 19-wavelength detection is performed during the separation of a three-dye sample mixture.

Fast extraction, amplification and analysis of genes from human blood

In order to shorten the time spent on the sample preparation for gene analysis, a novel method was proposed through the combination of fast DNA extraction and purification by Generation capture disk, amplification by capillary polymerase chain reaction, and confirmation of amplification products by microchip electrophoresis. With this method, 3 microL blood was enough to obtain adequate target fragments in human genes. Under the optimal conditions in each step, the sample preparation for eight fragments in beta-globin gene and four fragments in ras gene could be finished within 20 min. Since all the experiments were performed on commercial instruments, this method showed a wide range of applicability. In addition, other advantages such as fast speed and low consumption of samples were demonstrated. All these merits proved that such a combination method was of great potential for the clinical diagnostics.

Locus-specific brackets for reliable typing of Y-chromosome short tandem repeat markers

Short tandem repeat (STR) loci, widely used as genetic markers in disease diagnostic studies and human identity applications, are traditionally genotyped through comparison of allele sizes to a sequenced allelic ladder. Allelic ladders permit a floating bin allele calling method to be utilized, which enables reliable allele calling across laboratories, instrument platforms, and electrophoretic conditions. Precise sizing methods for STR allele calling involving fixed bins can also be used when a high degree of precision has been demonstrated within an instrument platform and a set of electrophoretic conditions. An alternative method for reliable genotyping of STR markers, locus-specific brackets (LSBs), is introduced here. LSBs are artificial alleles created through molecular biology manipulations to be shorter or longer than alleles commonly seen in populations under investigation. The size and repeat number of measured alleles are interpolated between the two LSB products that are mixed with the polymerase chain reaction-amplified STR alleles. The advantages and limitations of the LSB approach are described along with a concordance study between the LSB typing approach and other STR typing methods. Complete agreement was observed with 162 samples studied at 5 Y-chromosome loci.

Microfabricated systems for nucleic acid analysis

High throughput and automation of nucleic acid analysis are required in order to exploit the information that has been accumulated from the Human Genome Project. Microfabricated analytical systems enable parallel sample processing, reduced analysis-times, low consumption of sample and reagents, portability, integration of various analytical procedures and automation. This review article discusses miniaturized analytical systems for nucleic acid amplification, separation by capillary electrophoresis, sequencing and hybridization. Microarrays are also covered as a new analytical tool for global analysis of gene expression. Thus. instead of studying the expression of a single gene or a few genes at a time we can now obtain the expression profiles of thousands of genes in a single experiment.

A microfluidic platform using molecular beacon-based temperature calibration for thermal dehybridization of surface-bound DNA

This work presents a simple microfluidic device with an integrated thin-film heater for studies of DNA hybridization kinetics and double-stranded DNA melting temperature measurements. The heating characteristics of the device were evaluated with a novel, noninvasive indirect technique using molecular beacons as temperature probes inside reaction chambers. This is the first microfluidic device in which thermal dehybridization of surface-bound oligonucleotides was performed for measurement of double-stranded DNA melting temperatures with +/- 1 degrees C precision. Surface modification and oligonucleotide immobilization were performed by continuously flowing reagents through the microchannels. The resulting reproducibility of oligonucleotide surface densities, at 9% RSD, was better than for the same modification chemistries on glass slides in unstirred reagent solutions (RSD=20%). Moreover, the surface density of immobilized DNA probe molecules could be varied controllably by changing the concentration of the reagent solution used for immobilization. Thus, excellent control of surface characteristics was made possible, something which is often difficult to achieve with larger devices. Solid-phase hybridization reactions, a fundamental aspect of microarray technologies often taking several hours in conventional systems, were reduced to minutes in this device. It was also possible to determine forward rate constants for hybridization, k. These varied from 820,000 to 72,000 M(-1) s(-1), decreasing as surface densities increased. Surface densities could therefore be optimized to obtain rapid hybridization using such an approach. Taken together, this combined microfluidic/small-volume heating approach represents a powerful tool for surface-based DNA analysis.

DNA sequencing and genotyping in miniaturized electrophoresis systems

Advances in microchannel electrophoretic separation systems for DNA analyses have had important impacts on biological and biomedical sciences, as exemplified by the successes of the Human Genome Project (HGP). As we enter a new era in genomic science, further technological innovations promise to provide other far-reaching benefits, many of which will require continual increases in sequencing and genotyping efficiency and throughput, as well as major decreases in the cost per analysis. Since the high-resolution size- and/or conformation-based electrophoretic separation of DNA is the most critical step in many genetic analyses, continual advances in the development of materials and methods for microchannel electrophoretic separations will be needed to meet the massive demand for high-quality, low-cost genomic data. In particular, the development (and commercialization) of miniaturized genotyping platforms is needed to support and enable the future breakthroughs of biomedical science. In this review, we briefly discuss the major sequencing and genotyping techniques in which high-throughput and high-resolution electrophoretic separations of DNA play a significant role. We review recent advances in the development of technology for capillary electrophoresis (CE), including capillary array electrophoresis (CAE) systems. Most of these CE/CAE innovations are equally applicable to implementation on microfabricated electrophoresis chips. Major effort is devoted to discussing various key elements needed for the development of integrated and practical microfluidic sequencing and genotyping platforms, including chip substrate selection, microchannel design and fabrication, microchannel surface modification, sample preparation, analyte detection, DNA sieving matrices, and device integration. Finally, we identify some of the remaining challenges, and some of the possible routes to further advances in high-throughput DNA sequencing and genotyping technologies.

Human genomic DNA analysis using a semi-automated sample preparation, amplification, and electrophoresis separation platform

The growing importance of analyzing the human genome to detect hereditary and infectious diseases associated with specific DNA sequences has motivated us to develop automated devices to integrate sample preparation, real-time PCR, and microchannel electrophoresis (MCE). In this report, we present results from an optimized compact system capable of processing a raw sample of blood, extracting the DNA, and performing a multiplexed PCR reaction. Finally, an innovative electrophoretic separation was performed on the post-PCR products using a unique MCE system. The sample preparation system extracted and lysed white blood cells (WBC) from whole blood, producing DNA of sufficient quantity and quality for a polymerase chain reaction (PCR). Separation of multiple amplicons was achieved in a microfabricated channel 30 microm x 100 microm in cross section and 85 mm in length filled with a replaceable methyl cellulose matrix operated under denaturing conditions at 50 degrees C. By incorporating fluorescent-labeled primers in the PCR, the amplicons were identified by a two-color (multiplexed) fluorescence detection system. Two base-pair resolution of single-stranded DNA (PCR products) was achieved. We believe that this integrated system provides a unique solution for DNA analysis.

Microfabricated electrophoresis systems for DNA sequencing and genotyping applications: current technology and future directions

Many routine genomic-analysis assays rely on gel electrophoresis to perform size-selective fractionation of DNA fragments in the size range below 1 kb in length. Over the past decade, impressive progress has been made towards the development of microfabricated electrophoresis systems to conduct these assays in a microfluidic lab-on-a-chip format. Since these devices are inexpensive, require only nanolitre sample volumes, and do not rely on the availability of a pre-existing laboratory infrastructure, they are readily deployable in remote field locations for use in a variety of medical and biosensing applications. The design and construction of microfabricated electrophoresis devices poses a variety of challenges, including the need to achieve high-resolution separations over distances of a few centimetres or less, and the need to easily interface with additional microfluidic components to produce self-contained integrated DNA-analysis systems. In this paper, we review recent efforts to develop devices to satisfy these requirements and live up to the promise of fulfilling the growing need for inexpensive portable genomic-analysis equipment.

DNA diagnosis by capillary electrophoresis and microfabricated electrophoretic devices

DNA diagnosis is experiencing an impressive progression towards the development of novel technology to identify various clinically relevant categories of genetic changes and to meet the exponential growth of genomics. The introduction of capillary electrophoresis has dramatically accelerated the completion of the first draft of the human DNA sequence in the Human Genome Project, and thus, has become the method of choice for analysis of various genetic variants. The recent development of microfabricated electrophoretic devices has led to the possibility of integrating multiple sample handling with the actual measurement steps required for automation of molecular diagnostics. This review highlights the most recent progress in capillary electrophoresis and electrophoretic microdevices for DNA-based diagnostics, including the important areas of genotyping for point mutation, single nucleotide polymorphisms, short tandem repeats and organism identification. The application of these techniques for infectious and genetic disease diagnosis, as well as forensic identification purpose, are covered. The promising development and the challenges for techinical problems are also discussed.

Microchip electrophoresis-based separation of DNA

Miniaturized instruments have developed very quickly in the last decade. This review is focused on the microchip electrophoresis-based separation of DNA. Fundamentals, including the chip format, substrates and fabrication technologies, fluid control, as well as various detection methods, are summarized. Array electrophoresis microchip and the on-chip integration of electrophoresis with other systems are introduced as well. In addition, the application of microchip electrophoresis in DNA sizing, genetic analysis and DNA sequencing are also presented in this paper.

Microfluidic chips for clinical and forensic analysis

This review gives an overview of developments in the field of microchip analysis for clinical diagnostic and forensic applications. The approach chosen to review the literature is different from that in most microchip reviews to date, in that the information is presented in terms of analytes tested rather than microchip method. Analyte categories for which examples are presented include (i) drugs (quality control, seizures) and explosives residues, (ii) drugs and endogenous small molecules and ions in biofluids, (iii) proteins and peptides, and (iv) analysis of nucleic acids and oligonucleotides. Few cases of microchip analysis of physiological samples or other "real-world" matrices were found. However, many of the examples presented have potential application for these samples, especially with ongoing parallel developments involving integration of sample pretreatment onto chips and the use of fluid propulsion mechanisms other than electrokinetic pumping.

High-speed analysis of multiplexed short tandem repeats with an electrophoretic microdevice

We report the development of a robust and effective method for multiplexed short tandem repeat (STR) analysis within a chip-based microdevice. The method uses a laser-induced fluorescence detection system and simultaneously detects three- and four-color multiplexed polymerase chain reaction (PCR) samples. Analyses of the eight combined DNA index system (CODIS) STR loci were performed in 20 min with single-base-pair resolution ranging from 0.75 to 1. A simultaneous analysis of fifteen loci-ladders and a gender marker Amelogenin based on the PowerPlexTM 16 System was achieved in less than 35 min. The system is capable of repetitive operation and may be extended to high-throughput multilane devices that could be readily interfaced to an automated sample loading system.

Bioanalysis in microfluidic devices

Microfabricated bioanalytical devices (also referred to as laboratory-on-a-chip or micro-TAS) offer highly efficient platforms for simultaneous analysis of a large number of biologically important molecules, possessing great potential for genome, proteome and metabolome studies. Development and implementation of microfluidic-based bioanalytical tools involves both established and evolving technologies, including microlithography, micromachining, micro-electromechanical systems technology and nanotechnology. This article provides an overview of the latest developments in the key device subject areas and the basic interdisciplinary technologies. Important aspects of DNA and protein analysis, interfacing issues and system integration are all thoroughly discussed, along with applications for this novel "synergized" technology in high-throughput separations of biologically important molecules. This review also gives a better understanding of how to utilize these technologies as well as to provide appropriate technical solutions to problems perceived as being more fundamental.

High-throughput genotyping of repeat polymorphism in the regulatory region of serotonin transporter gene by gel microchip electrophoresis

Large-scale genotyping of the repeat polymorphism in the regulatory region of the serotonin transporter gene (5-HTTLPR) was attempted by polymerase chain reaction (PCR) amplification followed by gel microchip electrophoresis analysis. The multilane (96) format of the gel microchip system allowed parallel separation of a large number of samples. The separation and visualization of the PCR amplicons from either the 5-HTTLPR short allele (number of repeats are 14) or the 5-HTTLPR long form (16 repeats) was completed in a few minutes. Genotyping of healthy Caucasian individuals showed that the short allele had a somewhat lower frequency (0.42) than the long form (0.58), and the genotype frequencies fulfilled the criteria of the Hardy-Weinberg equilibrium (chi = 0.012, p = 0.994). Based on these results, gel microchip electrophoresis system proved to be a powerful tool for high throughput genotyping of repeat polymorphism.

Rapid, parallel separations of d1S80 alleles in a plastic microchannel chip

We have performed fast, parallel separations of alleles of the D1S80 locus in a plastic, multi-channel chip, replicated from a microfabricated master and laminated with a plastic film. The array of 16 channels was filled with a replaceable sieving polymer, and a size-dependent, electrophoretic separation of the DNA fragments was performed in all channels in less than 10 min, representing a 30-fold increase in throughput compared to that on a single-capillary instrument. To detect the fragments in all 16 channels in parallel during the run, we designed and built a scanning, confocal, laser-induced fluorescence system. The electropherograms were then used to determine the sample genotype. To demonstrate the use of multiplexed, microchannel arrays for real-life samples, we amplified D1S80 alleles from genomic DNA extracted from whole blood and separated these alleles by electrophoresis in the plastic chip. Evaluation of the electrophoretic data showed that, using a 300- and a 1,000-base pair fragment as internal mobility markers, 83% of the alleles were assigned correctly, using the allele identification from a single capillary instrument as a reference. This work demonstrates that, with improvements in the microchannel electrophoresis system, it is feasible to perform rapid, parallel genotyping in mass-produced, inexpensive, disposable plastic devices for large-scale applications in medicine and the life sciences.

Fast separation of oligonucleotide and triplet repeat DNA on a microfabricated capillary electrophoresis device and capillary electrophoresis

A laser-induced fluorescence detection system coupled with a highly sensitive silicon-intensified target (SIT) camera is successfully applied to the imaging of a band for DNA fragment labeling by fluorescence dye in a microchannel, and to the visualizing of the separation process on a microfabricated chip. We demonstrated that an only 6 mm separation channel is sufficient for the separation of triplet repeat DNA fragment and DNA molecular marker within only 12 s. The separation using the microfabricated capillary electrophoresis device is confirmed to be at least 18 times faster than the same separation carried out by conventional capillary electrophoresis with 24.5 cm effective length. The use of a short capillary with 8.5 cm effective length is also efficient for fast separation of DNA; however, the microchip technology is even faster than capillary electrophoresis using a short capillary.

Ultrafast detection of microsatellite repeat polymorphism in endothelin 1 gene by electrophoresis in short capillaries

The methodology and instrumentation for fast denaturing electrophoresis in short capillaries was developed and exemplified by detection of short tandem repeat polymorphism in the endothelin 1 gene. The resolution of two nucleotides, which is required for the detection of a dinucleotide repeat polymorphism, was achieved in a capillary of an effective length of 2.5 cm at a temperature of 600C and an electric field strength of 600 V/cm in 42 s. Thus, the use of denaturing electrophoresis in short capillaries with laser-induced fluorescence detection resulted in a reduction of analysis time by a factor of 200 when compared to the conventional slab gel electrophoresis. The developed methodology and instrumentation is advantageous for an implementation in clinical diagnostics and genetic population screening where fast analytical instrumentation amenable to automation is of paramount importance.

Toward real-world sequencing by microdevice electrophoresis

We report results using a microdevice for DNA sequencing using samples from chromosome 17, obtained from the Whitehead Institute Center for Genome Research (WICGR) production line. The device had an effective separation distance of 11.5 cm and a lithographically defined injection width of 150 microm. The four-color raw data were processed, base-called by the sequencing software Trout, and compared to the corresponding ABI 377 sequence from WICGR. With a criteria of 99% accuracy, we achieved average continuous reads of 505 bases in 27 min with 3% linear polyacrylamide (LPA) at 150 V/cm, and 460 bases in 22 min with 4% LPA at 200 V/cm at a temperature of 45 degrees C. In the best case, up to 565 bases could be base-called with the same accuracy in <25 min. In some instances, Trout allowed for accurate base-calling down to a resolution R as low as R = 0.35. This may be due in part to the high signal-to-noise ratio of the microdevice. Unlike many results reported on capillary machines, no additional sample cleanup other than ethanol precipitation was required. In addition, DNA fragment biasing (i.e., discrimination against larger fragments) was reduced significantly through the unique sample injection mechanism of the microfabricated device. This led to increased signal strength for long fragments, which is of great importance for the high performance of the microdevice.