Pathways for the Degradation of Styrene

Insights into plastic biodegradation: community composition and functional capabilities of the superworm (Zophobas morio) microbiome in styrofoam feeding trials

Plastics are inexpensive and widely used organic polymers, but their high durability hinders biodegradation. Polystyrene, including extruded polystyrene (also known as styrofoam), is among the most commonly produced plastics worldwide and is recalcitrant to microbial degradation. In this study, we assessed changes in the gut microbiome of superworms (Zophobas morio) reared on bran, polystyrene or under starvation conditions over a 3 weeks period. Superworms on all diets were able to complete their life cycle to pupae and imago, although superworms reared on polystyrene had minimal weight gains, resulting in lower pupation rates compared to bran reared worms. The change in microbial gut communities from baseline differed considerably between diet groups, with polystyrene and starvation groups characterized by a loss of microbial diversity and the presence of opportunistic pathogens. Inferred microbial functions enriched in the polystyrene group included transposon movements, membrane restructuring and adaptations to oxidative stress. We detected several encoded enzymes with reported polystyrene and styrene degradation abilities, supporting previous reports of polystyrene-degrading bacteria in the superworm gut. By recovering metagenome-assembled genomes (MAGs) we linked phylogeny and functions and identified genera including Pseudomonas, Rhodococcus and Corynebacterium that possess genes associated with polystyrene degradation. In conclusion, our results provide the first metagenomic insights into the metabolic pathways used by the gut microbiome of superworms to degrade polystyrene. Our results also confirm that superworms can survive on polystyrene feed, but this diet has considerable negative impacts on host gut microbiome diversity and health.

Lessons From Insect Fungiculture: From Microbial Ecology to Plastics Degradation

Anthropogenic activities have extensively transformed the biosphere by extracting and disposing of resources, crossing boundaries of planetary threat while causing a global crisis of waste overload. Despite fundamental differences regarding structure and recalcitrance, lignocellulose and plastic polymers share physical-chemical properties to some extent, that include carbon skeletons with similar chemical bonds, hydrophobic properties, amorphous and crystalline regions. Microbial strategies for metabolizing recalcitrant polymers have been selected and optimized through evolution, thus understanding natural processes for lignocellulose modification could aid the challenge of dealing with the recalcitrant human-made polymers spread worldwide. We propose to look for inspiration in the charismatic fungal-growing insects to understand multipartite degradation of plant polymers. Independently evolved in diverse insect lineages, fungiculture embraces passive or active fungal cultivation for food, protection, and structural purposes. We consider there is much to learn from these symbioses, in special from the community-level degradation of recalcitrant biomass and defensive metabolites. Microbial plant-degrading systems at the core of insect fungicultures could be promising candidates for degrading synthetic plastics. Here, we first compare the degradation of lignocellulose and plastic polymers, with emphasis in the overlapping microbial players and enzymatic activities between these processes. Second, we review the literature on diverse insect fungiculture systems, focusing on features that, while supporting insects' ecology and evolution, could also be applied in biotechnological processes. Third, taking lessons from these microbial communities, we suggest multidisciplinary strategies to identify microbial degraders, degrading enzymes and pathways, as well as microbial interactions and interdependencies. Spanning from multiomics to spectroscopy, microscopy, stable isotopes probing, enrichment microcosmos, and synthetic communities, these strategies would allow for a systemic understanding of the fungiculture ecology, driving to application possibilities. Detailing how the metabolic landscape is entangled to achieve ecological success could inspire sustainable efforts for mitigating the current environmental crisis.

The dissolution and microbial degradation of mobile aromatic hydrocarbons from a Pintsch gas tar DNAPL source zone

Source zones containing tar, a dense non-aqueous phase liquid (DNAPL), can contaminate groundwater for centuries. A common occurrence of tar is at former Pintsch gas factories. Little is known about the composition and fate of contaminants dissolving from Pintsch gas tar DNAPL. In this study, we determined the composition and water-soluble characteristics of mobile aromatic hydrocarbons and their biodegradation metabolites in the DNAPL contaminated groundwater at a former Pintsch gas tar plant. We assessed the factors that determine the fate of observed groundwater contaminants. Measured values of density (1.03-1.06 kg/m³) and viscosity (18.6-39.4 cP) were found to be relatively low compared to common coal tars. Analysis showed that unlike common coal tars phenanthrene is the primary component rather than naphthalene. Moreover, it was found that Pintsch gas tar contains a relatively high amount of light molecular aromatic hydrocarbon compounds, such as benzene, toluene, ethylbenzene and xylenes (BTEX). Less commonly reported components, such as styrene, ethyltoluenes, di-ethylbenzene, 1,2,4,5-tetramethylbenzene, were also detected in water extracts from Pintsch gas tar. Moreover, 46 relatively hydrophilic metabolites were found within the tar samples. Metabolites present within the tar suggest biodegradation of mobile aromatic Pintsch gas tar compounds occurred near the DNAPL. Based on eleven detected suspect metabolites, a novel anaerobic biodegradation pathway is proposed for indene. Overall, our findings indicate that Pintsch gas tar has higher invasive and higher flux properties than most coal tars due to its relatively low density, low viscosity and, high content of water-soluble compounds. The partitioning of contaminants from multi-component DNAPL into the aqueous phase and re-dissolution of their slightly less hydrophobic metabolites back from the aqueous phase into the DNAPL is feasible and demonstrates the complexity of assessing degradation processes within a source zone.

Plastics: Environmental and Biotechnological Perspectives on Microbial Degradation

Plastics are widely used in the global economy, and each year, at least 350 to 400 million tons are being produced. Due to poor recycling and low circular use, millions of tons accumulate annually in terrestrial or marine environments. Today it has become clear that plastic causes adverse effects in all ecosystems and that microplastics are of particular concern to our health. Therefore, recent microbial research has addressed the question of if and to what extent microorganisms can degrade plastics in the environment. This review summarizes current knowledge on microbial plastic degradation. Enzymes available act mainly on the high-molecular-weight polymers of polyethylene terephthalate (PET) and ester-based polyurethane (PUR). Unfortunately, the best PUR- and PET-active enzymes and microorganisms known still have moderate turnover rates. While many reports describing microbial communities degrading chemical additives have been published, no enzymes acting on the high-molecular-weight polymers polystyrene, polyamide, polyvinylchloride, polypropylene, ether-based polyurethane, and polyethylene are known. Together, these polymers comprise more than 80% of annual plastic production. Thus, further research is needed to significantly increase the diversity of enzymes and microorganisms acting on these polymers. This can be achieved by tapping into the global metagenomes of noncultivated microorganisms and dark matter proteins. Only then can novel biocatalysts and organisms be delivered that allow rapid degradation, recycling, or value-added use of the vast majority of most human-made polymers.