Popliteus impingement after TKA may occur with well-sized prostheses

Evaluation of 3D Footprint Morphology of Knee-Related Muscle Attachments Based on CT Data Reconstruction: A Feasibility Study

A three-dimensional (3D) understanding of muscle attachment footprints became increasingly relevant for musculoskeletal modeling. The established method to project attachments as points ignores patient-specific individuality. Research focuses on investigating certain muscle groups rather than comprehensively studying all muscles spanning a joint. Therefore, we present a reliable method to study several muscle attachments in order to reconstruct the attachment sites in 3D based on CT imaging for future applications in musculoskeletal modeling. For the present feasibility study, 23 knee-related muscle attachments were CT-scanned postmortem from four nonadipose male specimens. For this, the specific muscle attachments were dissected and marked with a barium sulfate containing paint (60 g BaSO4 in 30 mL water and 10 mL acrylic paint). Subsequently, bone geometries and muscle attachments were reconstructed and evaluated from CT datasets. Bone morphology and footprint variations were studied. Exemplarily, variations were high for pes anserinus insertions (mean 56%) and the origins of M. biceps femoris (mean 54%). In contrast, the origins of the vastus muscles as well as the insertion of the Achilles tendon showed low variation (mean 9% and 13%, respectively). Most attachment sites showed variation exceeding the individuality of bone morphology. In summary, the present data were consistent with the few published studies of specific muscle footprints. Our data shed light on the high variability of muscle attachments, which need to be addressed when studying muscle forces and movements through musculoskeletal modeling. This is the first step to achieving a more profound understanding of muscle morphology to be utilized in numerical simulations.

Which method for femoral component sizing when performing kinematic alignment TKA? An in silico study

INTRODUCTION

The kinematically alignment (KA) technique for TKA aims to reproduce the pre-arthritic knee anatomy, including both the femoro-tibial and femoro-patellar joints. An in silico study was conducted to compare 3 different femoral component sizing techniques to identify the anatomical landmark which allows closest restoration of the native trochlear anatomy. Our study's question was: what was the best method for sizing the femoral component when performing KA-TKA? It was hypothesized that sizing the femoral component by aiming to restore the groove height would be the best method to restore the native trochlear anatomy.

METHODS

GMK sphere® (Medacta) femoral component 3D models were virtually kinematically aligned on 30 tri-dimensional (3D) bony osteoarthritis knee models. The femoral component was mediolaterally positioned to match distal native and prosthetic grooves. Three methods were used to size the femoral component: a conventional method with the anterior femoral cut flush to the femoral cortex (C-KATKA) and two alternative personalized methods aiming to recreate either the medial facet's height (ATM-KATKA) or the groove's height (ATG-KATKA). In-house analysis software was used to compare native and prosthetic trochlear articular surfaces and mediolateral implant overhangs.

RESULTS

Compared with the C-KATKA, ATG-KATKA and ATM-KATKA techniques increased the component size by a mean of 0.90 (SD 0.31, min 0.5 to max 1.5) (p<0.001) and 1.02 (SD 0.31, min 0.5 to max 1.5) (p<0.001), respectively. C-KATKA technique substantially proximally understuffed the trochleae with maximum values of 7.11mm (SD 1.39, min 3.93mm to max 10.57mm) in the medial facet, 4.72mm (SD 1.27, min 1.46mm to max 6.86mm) in the lateral facet and 4.51mm (SD 1.40, min 1.92mm to max 7.30mm) in the groove, respectively. Alternative techniques understuffed medial facet with maximum values of 5.07mm (SD 1.29, min 2.83mm to max 8.34mm) and 4.70mm (SD 1.52, min 0.83mm to max 8.04mm) for ATG-KATKA and ATM-KATKA techniques, respectively. There was no significant understuffing of the groove or lateral facet for alternative techniques (ATM and ATG). The ATM-KATKA and ATG-KATKA techniques generated mediolateral implant overhang, mainly postero-lateral, with a rate of 90.0% and 86.7%, respectively. In this study, no mediolateral implant overhang was found for C-KATKA.

DISCUSSION/CONCLUSION

The C-KATKA technique substantially understuffs the native trochlear articular surfaces in medial, lateral and groove parts. Alternative techniques (ATM-KATKA and ATG-KATKA) for sizing the femoral component better restore the native trochlear anatomy but also generate a high rate of postero-lateral implant overhangs. Would this postero-lateral implant overhang be clinically deleterious remains unknown? The aspect ratio of contemporary femoral TKA implants can probably be optimized to allow a better anatomical restoration of the anterior femoral compartment.

LEVEL OF EVIDENCE

II, in silico study.

Isolated lateral-sided knee pain in total knee arthroplasty. A review

Isolated lateral-sided knee pain is a unique problem following total knee arthroplasty (TKA). Reported causes include soft tissue impingement against extruded cement, an overhanging tibial tray, remnant osteophytes rubbing against the iliotibial band (ITB), popliteal tendon impingement, fabella syndrome, and synovial tissue impingement in the lateral gutter. In addition, iliotibial band traction syndrome secondary to guided motion Bi-cruciate stabilizing knee arthroplasty has been recognized as a new clinical entity. Initial work up should include ruling out the most common causes of painful TKA including infection, aseptic loosening, and instability. Radiographs and CT scan are utilized to identify potential source of pain. Ultrasound evaluation (with elicited probe tenderness) can increase diagnostic accuracy. Ultrasound guided local anesthetic injections can confirm the source of pain. Anti-inflammatory medications, physical therapy with ITB stretches, and therapeutic local steroid injections are initial treatment modalities. Satisfactory resolution of symptoms may require surgical intervention directed at the specific cause and may avoid the morbidity associated with revision TKA.

The popliteal eminence shows that the intra-articular popliteal tendon supports posterolateral knee stability

The intra-articular popliteal tendon (iPT) is responsible for the dynamic stability of the posterolateral part of the knee joint. In this study, the involvement of the iPT in posterolateral stability in response to knee flexion was investigated anatomically. Thirty-one knees from thirty formalin-fixed room cadavers (17 male knees, 14 female knees; average age 86.9 years) were used. The knee was prepared with the distal 1/3 of the lower femur and crus and was flexed at 0°, 30°, 60°, and 90° in a special jig to limit knee rotation. The series of movements was plotted on the coordinate system using the Quadrant method. The iPT was in strong contact with a thick cartilage area, which we called the "popliteal eminence", at the lateral condyle of the femur. The average iPT angles with respect to the femoral axis were 28.78°, 49.79°, 77.74°, and 115.44° at knee flexion of 0°, 30°, 60°, and 90°, respectively. The iPT was strongly associated with the popliteal eminence at 29.5° in Type I and 27.09° in Type II knee flexion. The iPT has been conventionally regarded as a secondary restraint of posterior movement, acting as a stabilizer. However, the iPT appears to work more positively on knee joint stability because it was in strong enough contact to create the popliteal eminence. The iPT supports the femur in the posterolateral region in mild knee flexion.

Popliteal tendon impingement as a cause of pain following total knee arthroplasty: a systematic review

INTRODUCTION

Popliteal tendon impingement (PTI) is an under-recognized cause of persistent pain following total knee arthroplasty (TKA). The purpose of the systematic review was to summarize and outline successful strategies in the diagnosis and management of PTI.

METHODS

A systematic review following the PRISMA guidelines was performed for four databases: MEDLINE (Pubmed), Ovid EMBASE, Web of Science, and Cochrane Database. It was registered in the International Prospective Register for Systematic Reviews and Meta-analysis (PROSPERO) under the registration number: CRD42023398723. The risk of bias assessment was performed using the criteria of the methodological index for non-randomized studies (MINORS).

RESULTS

A total of 8 studies were included. There were 2 retrospective case series and 6 case reports. The follow-up ranged from 6 to 30 months. Two studies described PTI as an intraoperative phenomenon during TKA with "snapping"; whilst 6 studies described indications and outcomes for arthroscopic tenotomy for PTI following TKA. In making the diagnosis, there was concurrence that the posterolateral pain should be focal and that dynamic ultrasonography and diagnostic injection play an important role. Two specific clinical tests have been described. There was no consistency regarding the need for imaging. There were no reports of instability following popliteal tendon tenotomy or other complications.

CONCLUSION

PTI should be suspected as a cause for persistent focal pain at the posterolateral knee following TKA. The diagnosis can be suspected on imaging and should be confirmed with dynamic ultrasonography and an ultrasound-guided diagnostic injection. An arthroscopic complete tenotomy of the tendon can reliably alleviate pain and relies on correct diagnosis. There is no evidence for clinically relevant negative biomechanical consequences following tenotomy.

LEVEL OF EVIDENCE

Systematic Review of Level IV and V studies.

Clinical significance of distal femur morphology in a healthy Mongolian youth population

Morphological parameters of knee joint are related to race and nationality. At present, knee prosthesis come from white male population. Due to the mismatch between the prosthesis and other ethnic groups, the prosthesis life span is reduced, revision surgery and the patients' economic burden are increased. There is no data of the Mongolian ethnic group. In order to treat patients more accurately, we measured the Mongolian data of the femoral condyle. A total of 122 knee joints were scanned in 61 volunteers (21 males and 40 females) with an average age of 23.259 ± 1.395 years. The Mimics software was used to reconstruct the 3D image and measure the data of each line. The data were analyzed by statistical methods such as t test, and P < 0.05 was taken as the significant. 122 normal femoral condyle data were obtained. The mean transverse diameter of femoral condyle is 76.472 ± 5.952 mm, medial condyle is 29.259 ± 11.461 mm, and the sagittal diameter of the medial condyle was 56.758 ± 4.163 mm. The transverse diameter of the lateral femoral condyle is 29.388 ± 3.157 mm, the sagittal diameter of the lateral condyle is 58.937 ± 3.527 mm and the femoral plane rate is 1.264 ± 0.072. (1) There was no statistical significance in the left and right knee joint data (P > 0.05). (2) The different genders data of femoral condyle were statistically significant (P < 0.05). (3) Compared with other nationalities and races, the data of femoral condyle are different. (4) There are differences between femoral surface ratio and mainstream prosthesis data.

Diagnostic ultrasound and ultrasound-guided injections for peri-articular pain after knee replacement

OBJECTIVE

The purpose of this technical report is to review the sonographic spectrum of abnormalities accounting for peri-articular pain after knee replacement surgery, as well as to demonstrate the clinical utility of ultrasound in the diagnosis and treatment of this subset of patients.

MATERIALS AND METHODS

Utilizing an imaging report database, we performed a search for ultrasound examinations performed by a single radiologist for knee pain after knee arthroplasty at our institution over a 10-year period. The search yielded 63 patients, whom we have categorized by causative pathology, with representative diagnostic and procedural ultrasound images selected for inclusion.

RESULTS

Our search yielded multiple causes of peri-articular knee pain after arthroplasty, including medial and lateral retinacular impingement and scarring, iliotibial band or conjoined tendon irritation, popliteus tendon impingement, medial collateral ligament impingement, pes anserine bursitis, and scarring of Hoffa's fat pad.

CONCLUSION

While knee arthroplasty is an often-successful procedure, it can be complicated by post-operative peri-articular knee pain. Ultrasound provides a valuable tool for the diagnosis of painful peri-articular knee pathology, as it allows for both static and dynamic evaluation, as well as direct correlation with patient symptoms, and is not confounded by the metal components. In addition to its diagnostic utility, ultrasound can also guide diagnostic and/or therapeutic injections of anesthetic and corticosteroid. Given these advantages, ultrasound is an important tool in managing the painful post-arthroplasty knee.

Arthroscopic popliteal tenotomy grants satisfactory outcomes in total knee arthroplasty with persistent localised posterolateral pain and popliteus tendon impingement

PURPOSE

The purpose was to estimate the prevalence of popliteus tendon impingement following TKA, and to describe the characteristics and the differential diagnosis protocol for this rare condition. The hypothesis was that arthroscopic popliteal tenotomy in TKA patients with suspected popliteus tendon impingement would relieve pain and improve satisfaction.

METHODS

Of 741 TKAs performed over three years, eight (1.1%, all women) had suspected popliteus tendon impingement, of which seven had severe localised posterolateral knee pain and one global knee pain. Upon confirmation of popliteus tendon impingement, arthroscopic popliteal tenotomy was performed, and outcomes (Pain on visual analogue scale (pVAS; best, 0; worst, 10), Oxford Knee Score (OKS; best, 48; worst, 0) and satisfaction (best, 100%; worst, 0%) assessed at mean 18-month follow-up.

RESULTS

At four to 30 months after TKA, arthroscopic exploration revealed popliteus tendon impingement in all eight knees. Six reported complete pain relief (pVAS, 0) the day following arthroscopic popliteal tenotomy, whilst one reported some residual pain (pVAS, 2). The remaining patient with global pain reported no pain relief, and required revision TKA at 12 months. Excluding the revised TKA, OKS was between 19 and 43, and satisfaction was rated ≥ 80% in five of the remaining seven patients.

CONCLUSIONS

Arthroscopic popliteal tenotomy relieved symptoms in TKA patients with persistent localised posterolateral pain and a positive popliteus test. These findings suggest that the popliteus test is reliable to diagnose popliteus tendon impingement following TKA, which could be treated by arthroscopic popliteal tenotomy.

LEVEL OF EVIDENCE

Level IV, Small case series.

Knee Arthroscopy After Prior Total Knee ArthroplastyType of Study: Narrative Review

Total knee arthroplasty (TKA) results in substantial improvement for most patients with end-stage arthritis of the knee; however, approximately 20% of patients have an unsatisfactory result. Although many problems contributing to an unsatisfactory result after TKA are best addressed by revision TKA, some problems may be effectively addressed with arthroscopic treatment. The categories of pathology that can be addressed arthroscopically include peripatellar soft-tissue impingement (patellar clunk syndrome and patellar synovial hyperplasia), arthrofibrosis, and popliteus tendon dysfunction. Recognizing these disease entities and the role of arthroscopic surgery in the treatment of these lesions may be helpful in achieving a good outcome in certain patients who are unsatisfied with their knee arthroplasty.

Medial-lateral translational malalignment of the prosthesis on tibial stress distribution in total knee arthroplasty: A finite element analysis

Background: Poor prosthesis alignment during total knee arthroplasty could cause problems such as polyethylene spacer wear, leading to surgical failure and revision surgery. The problems caused by the malalignment of the tibial plateau prosthesis in the medial and lateral planes are unclear. We aimed to investigate the stress distribution and micromotion of the tibia when the tibial plateau prosthesis is translated 1 and 2 mm medially and laterally, respectively, using finite element analysis (FEA). Method: A non-homogeneous tibia model was created and load conditions when standing on two legs were applied using FEA to simulate the misaligned prosthesis. The stresses, stress distribution, and micromotion of the proximal tibia were analyzed in five positions of the tibial plateau prosthesis: Lateral-2 mm; Lateral-1 mm; Medium; Medial-2 mm; Medial-1 mm. Result: The maximum stress in the five groups with different misalignments of the platform was 47.29 MPa (Lateral-2 mm). The maximum micromotion among the five groups in different positions was 7.215 μm (Lateral-2 mm). Conclusion: When placing the tibial plateau prosthesis during total knee arthroplasty, an error of 2 mm or less is acceptable as long as it does not overhang.

Effect of the posterior sagging control device to the posterior tibial translation during posterior-stabilized total knee arthroplasty with modified gap technique

PURPOSE

In modern total knee arthroplasty (TKA), flexion and extension gaps between the femur and tibia are equilibrated before implanting the final components. Uncontrolled intraoperative posterior tibial translation (PTT) could cause an artifactual widening of the flexion gap, which could lead surgeons to alter the femoral component size. We designed an intraoperative posterior sagging control device to prevent intraoperative PTT. In this study, we investigated whether the use of this device could prevent artifactual widening of the flexion gap.

METHODS

Twenty-five patients, 21 women and four men, aged 74.2 years, were enrolled in this prospective study. All patients underwent postero-stabilized TKA using a navigation system. Intraoperative PTT, flexion and extension gaps with or without using the posterior sagging control device were measured with navigation system. These measurements were compared with or without the posterior sagging control device and after the final implantation also.

RESULTS

There were significant differences between the measurements performed with or without the posterior sagging control device when compared to the post-implantation measurements. The use of the device reduced the number of patients with a >3 mm increase in flexion gap from 7 (28%) to 1 (4%).

CONCLUSION

This study suggests that the posterior sagging control device prevents PTT and artificial flexion gap widening. This could prevent an unnecessary increase in component size.

Arthroscopic Osteophyte Resection for Osteophyte-Induced Popliteal Impingement

Popliteal tendinitis causes lateral knee pain. A cause is impingement of the popliteal tendon by lateral femoral condylar osteophytes. Conservative and surgical treatments have been reported; however, popliteal impingement is a relatively rare disease, and no treatment has been established. Reduction of mechanical stress is important in the treatment of impingement syndromes. The popliteal tendon is an important tissue that contributes to knee stability and, therefore, usually cannot be transected. On the other hand, osteophyte resection may allow the reduction of mechanical stress. Therefore, we describe an arthroscopic osteophyte resection technique for the treatment of osteophyte-induced popliteal impingement. In brief, this technique involves confirmation of popliteal impingement, osteophyte resection using an osteotome, smoothening of the resected area, and confirmation of the resolution of popliteal impingement.

Low-Degree Tibial Slope Angle Prevents Component Overhang by Enlarging the Lateral Plateau Surface Area in Total Knee Arthroplasty

This study aimed to investigate whether overhang or underhang around the tibial component that occurs during the placement of tibial baseplates was affected by different slope angles of the tibial plateau and determine the changes in the lateral and medial plateau diameters while changing the slope angle in total knee arthroplasty. Three-dimensional tibia models were reconstructed using the computed tomography scans of 120 tibial dry bones. Tibial plateau slope cuts were performed with 9, 7, 5, 3, and 0 degrees of slope angles 2-mm below the subchondral bone in the deepest point of the medial plateau. Total, lateral, and medial tibial plateau areas and overhang/underhang rates were measured at each cut level. Digital implantations of the asymmetric and symmetric tibial baseplates were made on the tibial plateau with each slope angles. Following the implantations, the slope angle that prevents overhang or underhang at the bone border and the slope angle that has more surface area was identified. A significant increase was noted in the total tibial surface area, lateral plateau surface area, and lateral anteroposterior distance, whereas the slope cut angles were changed from 9 to 0 degrees in both gender groups. It was found that the amount of posteromedial underhang and posterolateral overhang increased in both the asymmetric and symmetric tibial baseplates when the slope angle was changed from 0 to 9 degrees. Although the mediolateral diameter did not change after the proximal tibia cuts at different slope angles, the surface area and anteroposterior diameter of the lateral plateau could change, leading to increased lateral plateau area. Although prosthesis designs are highly compatible with the tibial surface area, it should be noted that the component overhangs, especially beyond the posterolateral edge, it can be prevented by changing the slope cut angle in males and females.

Selective Iliotibial Band Release for Iliotibial Band Traction Syndrome After Second-Generation Motion-Guided Bicruciate Stabilizing Total Knee Arthroplasty and Its Rationale: A Case Report With Review of Literature

Iliotibial band traction syndrome (ITBTS) after total knee arthroplasty (TKA) has been well documented following first-generation guided motion bicruciate substituting (BCS) TKA. The incidence of ITBTS following second-generation BCS has been found to be rare, and surgical release of the IT band has not been reported. A 64-year old male was diagnosed with ITBTS following second-generation guided motion BCS TKA. After a three-month trial of non-surgical treatment, he underwent selective open release of the iliotibial band (ITB), which successfully relieved his symptoms. Orthopedic surgeons should keep ITBTS as a possible differential diagnosis when evaluating the lateral-sided knee pain following guided motion BCS TKA.

Sexual dimorphism and racial diversity render bone-implant mismatch inevitable after off-the-shelf total knee arthroplasty: a systematic review and meta-analysis

PURPOSE

The purpose of this systematic review and meta-analysis was to investigate the variability in femoral geometric ratios among knees of different sexes and races, and to appreciate whether the observed variability is accommodated by commonly implanted total knee arthroplasty (TKA) components. The hypothesis was that the anthropometric studies report considerable variability of femoral geometric ratios among sexes and races.

METHODS

This systematic review and meta-analysis was performed according to the Preferred Reporting Items for Systematic reviews and Meta-analyses (PRISMA) criteria. Two authors independently conducted an electronic search using MEDLINE^® and Embase^® on 6 July 2020 for clinical studies reporting on femoral geometric ratios among sexes and races. Femoral geometric ratios were graphically represented as means and 2 standard deviations, and compared to those of 13 commonly implanted femoral components.

RESULTS

A total of 15 studies were identified that reported on a combined total of 2627 knees; all reported the aspect ratio, and 2 also reported the asymmetry ratio and trapezoidicity ratio. Men had wider knees than women, and compared to Caucasian knees, Arabian and Indian knees were wider, while East Asian were narrower. There were no differences in asymmetry ratio between men and women, nor among Caucasian and East Asian knees. Men had more trapezoidal knees than women, and East Asian knees were more trapezoidal than Caucasian knees. The commonly implanted femoral components accommodated less than a quarter of the geometric variability observed among sexes and races.

CONCLUSION

Anthropometric studies reported considerable sexual dimorphism and racial diversity of femoral geometric ratios. Since a surgeon generally only uses one or a few TKA brands, bone-implant mismatch remains unavoidable in a large proportion of knees. These findings support the drive towards personalized medicine, and accurate bone-implant fit may only be achievable through customisation of implants, though the clinical benefits of custom TKA remain to be confirmed.

LEVEL OF EVIDENCE

IV.

Preliminary Study on Immediate Postoperative CT Images and Values of the Modular Polyetheretherketone Based Total Knee Arthroplasty: An Observational First-in-Human Trial

BACKGROUND

Total knee arthroplasty (TKA) is now frequently performed and is highly successful. However, patient satisfaction after TKA is often difficult to achieve. Because of the presence of metallic prosthetic knee joints, there is a lack of imaging tools that can accurately assess the patient's postoperative prosthetic position, soft tissue impingement, and periprosthetic bone density after TKA. We conducted a clinical trial of the world's first totally modular polyetheretherketone (PEEK) TKA and determined the bone density values in the stress concentration area around the prosthesis based on postoperative computed tomography data to reconstruct a three-dimensional model of the PEEK prosthetic knee joint after implantation. Based on the model, the overhang of the prosthesis was measured at various locations on the prosthesis.

METHODS

All patients who underwent PEEK-based TKA were postoperatively assessed with radiography and computed tomography (CT). Hounsfield units (HUs) for the different components of the quantitative CT assessment were measured separately.

RESULTS

Ten patients (nine female and one male) aged 59-74 (mean 66.9, median 67) years were included. The HU values were as follows: PEEK prosthesis mean 182.95, standard deviation (SD) 4.90, coefficient of variation (CV) 2.68; polyethylene mean -89.41, SD 4.14, CV -4.63; lateral femoral osteochondral mean 192.19, SD 55.05, CV 28.64; lateral tibial osteochondral mean 122.94, SD 62.14, CV 42.86; medial femoral osteophyte mean 180.76, SD 43.48, CV 24.05; and medial tibial osteophyte mean 282.59, SD 69.28, CV 24.52. Analysis of the data at 1, 3, and 6 months showed that the mean PE (p = 0.598) and PEEK (p = 0.916) measurements did not change with the time of measurement. There was a decrease in bone mineral density in the lateral tibia at 3 months (p = 0.044). Otherwise, there was no significant change in bone density in other regions (p = 0.124-0.803). There was no overhang in all femoral prostheses, whereas there were two cases of overhang in tibial prostheses. Overhang measurements do not differ significantly across time points. The overhang measurements were not significantly different at all time points (p = 0.186-0.967).

CONCLUSION

PEEK knee joint prosthesis has excellent CT compatibility. The change in periprosthetic bone volume during the follow-up period can be determined using the HU value after CT scan, while the prosthesis position can be assessed. This assessment may potentially guide future improvements in knee prosthesis alignment techniques and artificial knee prosthesis designs.

Custom TKA: what to expect and where do we stand today?

INTRODUCTION

The concept of custom total knee arthroplasty (TKA) is explored with specific attention to current limitations. Arguments in favor of custom TKA are the anatomic and functional variability we encounter in our patients. The biggest conceptual challenge is to marry the need for correction of deformity with the ambition to stay as close as possible to original anatomy.

MATERIALS AND METHODS

A Pubmed search was performed on the following terms: 'patient specific implant', 'custom made implant', 'custom implant', 'total knee arthroplasty' and 'total knee replacement'. These studies were evaluated for the following intra- and post-operative variables: blood loss, hospital stay, range of motion, patient-reported outcome measures, limb and implant alignment, implant fit, tibiofemoral kinematics, complications and revision rates.

RESULTS

Out of 1117 studies found with the initial search, a total of 17 articles were included in the final analysis. In eight out of the 17 (47%) studies, either the research was commercially funded or one of the authors had a conflict of interest related to the work. 11 out of 17 studies included a control group in their study setup. Of those studies that included a control group, both superior and inferior results compared to off-the-shelf implants have been reported.

CONCLUSION

Custom knee implants are the next step in matching the geometric features of the prosthesis to the anatomy of the individual patient, after several iterations that added asymmetry and sizes in the existing implants. Several companies have proven that it is feasible to produce these implants in a safe way. An overview of current literature reveals the lack of strong methodological studies that prove the value of this new technology. Custom knee implants face conceptual and practical difficulties, some of which might be overcome with technological advances, such as robotics and artificial intelligence.

Lack of small tibial component size availability for females in a highly utilized total knee arthroplasty system

PURPOSE

Surgeons must rely on manufacturers to provide an appropriate distribution of total knee arthroplasty (TKA) sizes. There is a lack of literature regarding current appropriateness of tibial sizing schemes according to sex. As such, a study was devised assessing the adequacy of off-the-shelf tibial component size availability according to sex.

METHODS

A search was conducted to identify all primary TKAs between July 2012 and June 2019 performed using a single implant. Baseline patient characteristics were collected (age, weight, height, BMI, and race). Two cohorts were created according to patient sex. Tibial sizes for each cohort were collected. Tibial component bar graph and histogram were created according to component sizes. Skewness and kurtosis were calculated for each distribution. Overhang was noted and measured radiographically.

RESULTS

A total of 864 patients were identified, 38.7% males and 61.3% females. Most patients were Caucasian, and BMI was similar between cohorts. Tibial size distribution for males was as follows: 0.3% C, 4.8% D, 16.5% E, 40.1% F, 31.4% G, 6.9% H. Tibial size distribution for females was as follows: 30.8% C, 42.8% D, 23.0% E, 2.6% F, 0.8% G, 0.0% H. Histograms and normal curves demonstrated a fairly symmetric distribution of sizes for males (skewness = - 0.31, kurtosis = - 0.03). The distribution for females was positively skewed (skewness = 0.57, kurtosis = 0.12). Overall, overhang was noted in 16.6% of all size C tibias.

CONCLUSIONS

The results of this study highlight an implant-specific discrepancy in size availability affecting female patients which could result in inferior outcomes. The authors urge manufacturers to critically assess current implant size distribution availability to ensure both genders are adequately, and equally represented.

LEVEL OF EVIDENCE

IV.

No significant difference in early clinical outcomes of custom versus off-the-shelf total knee arthroplasty: a systematic review and meta-analysis

PURPOSE

The purpose of this systematic review and meta-analysis was to collect, synthesise and critically appraise findings of clinical studies that report outcomes of custom total knee arthroplasty (TKA). The hypothesis was that, compared to off-the-shelf (OTS) TKA, custom TKA would yield better surgical, clinical and radiographic outcomes.

METHODS

This systematic review and meta-analysis was performed in accordance with the guidelines of Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA). On 8 February 2021, two authors independently searched and screened articles using MEDLINE®, Embase® and the Cochrane Library without restriction on date of publication. Findings from eligible articles were narratively synthesised and tabulated, and when ≥ 3 comparative studies reported the same outcome, results were pooled and summarised in forest plots. Quality assessments of the studies were done according to the guidelines of the Joanna Briggs Institute (JBI) Checklists.

RESULTS

A total of 15 articles were eligible for data extraction, of which 9 were case-control studies reporting on 929 custom versus 998 OTS TKA, 5 were case series reporting on results of 587 custom TKA, and 1 was a cross-sectional study reporting on results of 44 custom versus 132 OTS TKA. Five studies that compared early revision rates found the overall effect in favour of OTS TKA (odds ratio (OR), 0.4; p = n.s.) but the result did not reach statistical significance. Four studies found no statistically significant difference in KSS knee (standardised mean difference (SMD), - 0.10; p = n.s.) and function (SMD, 0.03; p = n.s.), and five studies found no statistically significant difference in range of motion (SMD, 0.02; p = n.s.). One study that compared bone-implant fit between custom and three OTS tibial components found no overhang but revealed under-coverage of up to 18% in knees with custom tibial baseplates.

CONCLUSION

Custom TKA demonstrated no significant benefits compared to OTS TKA in terms of pooled clinical outcomes, but had considerably higher early revision rates. The findings of the present systematic review and meta-analysis suggest the need for studies with better comparable groups and standardisation of reporting outcomes amongst studies, that could increase the quality of evidence and enable pooling of results in future meta-analyses.

LEVEL OF EVIDENCE

Level IV.

Considerable inter-individual variability of tibial geometric ratios renders bone-implant mismatch unavoidable using off-the-shelf total knee arthroplasty: a systematic review and meta-analysis

PURPOSE

The purpose of this systematic review and meta-analysis was to investigate the variability in tibial geometric ratios among knees of different sexes and races to determine whether commercially-available tibial baseplates accommodate the morphologic diversity. The hypothesis was that anthropometric studies report considerable variability of tibial geometric ratios among sexes and races.

METHODS

This systematic review and meta-analysis was performed according to the preferred reporting items for systematic reviews and meta-analyses (PRISMA) criteria. Two authors independently conducted an electronic search using MEDLINE^® and Embase^® on 28 January 2021 for clinical studies reporting on tibial geometric ratios. Tibial geometric ratios, as reported by the clinical studies, were represented by plotting their means and two standard deviations for comparison to two symmetric and two asymmetric commercially-available tibial baseplates.

RESULTS

A total of 27 articles that reported on a combined total of 20,944 knees were eligible for data extraction. Variation in tibial aspect ratios was equal among sexes. The greatest variation in aspect ratio was observed among East Asians, followed by Caucasians, African-Americans, Indian and Middle Easterns. The variation in tibial asymmetry ratio was larger among men compared to women. The greatest variation in asymmetry ratio was observed among African-Americans, followed by Caucasians, East Asians, Indian and Middle Easterns. Bone-implant mismatch of > 3 mm overhang or > 4 mm under-coverage with four commercially-available tibial baseplates occurred in large proportions of knees due to variations in aspect ratio (in 17-100% of knees) and asymmetry ratio (in 7-100% of knees).

CONCLUSION

Anthropometric studies reported considerable inter-individual variability of tibial geometric ratios, which exceeded effects of sexual dimorphism and racial diversity. Bone-implant mismatch may be unavoidable in a large proportion of knees, when considering that a surgeon generally only uses one or a few TKA brands. These findings support the drive towards patient-specific implants to potentially achieve accurate bone-implant fit by implant customisation.

LEVEL OF EVIDENCE

IV.

Mismatched knee implants in Indonesian and Dutch patients: a need for increasing the size

PURPOSE

The aim of this study was to evaluate the anthropometric differences between knees of Indonesian Asians and Dutch Caucasians and the fit of nine different knee implant systems.

METHODS

A total of 268 anteroposterior (AP) and lateral knee preoperative radiographs from 134 consecutive patients scheduled for total knee arthroplasty at two different centres in Jakarta and Leiden were included. Both patient groups were matched according to age and sex and included 67 Asians and 67 Caucasians. We assessed the radiographic differences between the Asian and Caucasian anthropometric data. The dimensions of the nine knee implant designs (Vanguard, Genesis II, Persona Standard, Persona Narrow, GK Sphere, Gemini, Attune Standard, Attune Narrow, and Sigma PFC) were compared with the patients' anthropometric (distal femur and proximal tibia) measurements.

RESULTS

The Dutch Caucasian patients had larger mediolateral (ML) and AP femoral and tibial dimensions than the Indonesian Asians. The aspect ratios of the distal femur and tibia were larger in Asians than in Caucasians. The AP and ML dimensions were mismatched between the tibial components of the nine knee systems and the Asian anthropometric data. Both groups had larger ML distal femoral dimensions than the knee systems.

CONCLUSION

Absolute and relative differences in knee dimensions exist not only between Asian and Caucasian knees but also within both groups. Not all TKA systems had a good fit with the Asian and Caucasian knee phenotypes. An increase in the range of available knee component sizes would be beneficial, although TKA remains an adequate compromise.

LEVEL OF EVIDENCE

III.

Soft-tissue penetration of the oscillating saw during tibial resection in total knee arthroplasty

AIMS

Inadvertent soft tissue damage caused by the oscillating saw during total knee arthroplasty (TKA) occurs when the sawblade passes beyond the bony boundaries into the soft tissue. The primary objective of this study is to assess the risk of inadvertent soft tissue damage during jig-based TKA by evaluating the excursion of the oscillating saw past the bony boundaries. The second objective is the investigation of the relation between this excursion and the surgeon's experience level.

METHODS

A conventional jig-based TKA procedure with medial parapatellar approach was performed on 12 cadaveric knees by three experienced surgeons and three residents. During the proximal tibial resection, the motion of the oscillating saw with respect to the tibia was recorded. The distance of the outer point of this cutting portion to the edge of the bone was defined as the excursion of the oscillating saw. The excursion of the sawblade was evaluated in six zones containing the following structures: medial collateral ligament (MCL), posteromedial corner (PMC), iliotibial band (ITB), lateral collateral ligament (LCL), popliteus tendon (PopT), and neurovascular bundle (NVB).

RESULTS

The mean 75^th percentile value of the excursion of all cases was mean 2.8 mm (SD 2.9) for the MCL zone, mean 4.8 mm (SD 5.9) for the PMC zone, mean 3.4 mm (SD 2.0) for the ITB zone, mean 6.3 mm (SD 4.8) for the LCL zone, mean 4.9 mm (SD 5.7) for the PopT zone, and mean 6.1 mm (SD 3.9) for the NVB zone. Experienced surgeons had a significantly lower excursion than residents.

CONCLUSION

This study showed that the oscillating saw significantly passes the edge of the bone during the tibial resection in TKA, even in experienced hands. While reported neurovascular complications in TKA are rare, direct injury to the capsule and stabilizing structures around the knee is a consequence of the use of a hand-held oscillating saw when making the tibial cut. Cite this article: Bone Joint J 2020;102-B(10):1324-1330.

Why Reintervention After Total Knee Arthroplasty Fails? A Consecutive Cohort of 1170 Surgeries

BACKGROUND

The aim of this study was to analyze why contemporary reintervention after total knee arthroplasty (RiTKA) fails.

METHODS

Between January 2006 and December 2010, from a multicenter cohort of 1170 RiTKAs, we assessed all failures of RiTKA requiring additional surgery. All indications for the index reintervention were included. The minimum follow-up period was 3 years.

RESULTS

A total of 192 (16.4%) patients required additional surgery after RiTKA (re-reintervention). The mean follow-up period was 7.7 years. Mean age was 69.2 years. The mean time to re-reintervention was 9.6 months with 90.1% of rTKA failure occurring within the first two years. Infection was the main cause of new surgery after RiTKA (47.9%; n = 92/192). Other causes included extensor mechanism pathology (14.6%), stiffness (13.5%), pain (6.8%), aseptic loosening (5.2%), laxity (5.2%), periprosthetic fracture (3.6%), and wound pathology (3.1%). In four groups, the main indication for re-reintervention was recurrence of the pathology leading to the first reintervention: RiTKA for infection (59/355, 16.6%, P < .05), stiffness (18/174, 10.3%, P < .05), extensor mechanism failure (9/167, 5.4%, P < .05), and RiTKA for pain (4/137, 2.9%, P = .003). Global survival curve analysis found 87.9% survivorship without re-reintervention at one year and 83% at eight years.

CONCLUSION

Contemporary RiTKA failures mainly occur in the first two postoperative years. Infection is the main cause of failure in RiTKA. Recurrence of the initial pathology occurs in four groups of RiTKA and is the main indication for re-reintervention in these groups; infection (16.6%), stiffness (10.3%), extensor mechanism failure (5.4%), and pain (2.9%).

A landmark-based 3D analysis reveals a narrower tibial plateau and patella in trochlear dysplastic knees

PURPOSE

The trochlear dysplastic femur has a specific morphotype previously characterised by not only dysplastic features of the trochlea but also by specific features of the notch and posterior femur. In this study the morphology of the tibia and patella was investigated to gain further insight in the complete geometrical complexity of the trochlear dysplastic knee.

METHODS

Arthro-CT scan-based 3D models of 20 trochlear dysplastic and 20 normal knees were uniformly scaled and landmarks and landmark-based reference planes were created to quantify a series of morphometric characteristics of the tibia and patella.

RESULTS

In the mediolateral direction, the 3D-analysis revealed a 3% smaller medial tibial plateau (30.4 ± 1.6 mm vs 31.5 ± 1.6 mm), a 3% smaller overall width of the tibial plateau (73.6 ± 2.0 mm vs 75.7 ± 2.0 mm), a 16% smaller medial facet (17.3 ± 2.2 mm vs 20.1 ± 1.3 mm) and a 4% smaller overall width of the patella (41.7 ± 2.5 mm vs 43.4 ± 2.3 mm) in trochlear dysplastic knees. In the anteroposterior direction, the lateral tibial plateau of trochlear dysplastic knees was 5% larger (37.2 ± 2.3 mm vs 35.5 ± 3.1 mm). A correlation test between the width of the femur and the width of the tibia revealed that trochlear dysplastic knees show less correspondence between the femur and tibia compared to normal knees.

CONCLUSION

Significant differences in the morphology of the tibial plateau and patella were detected between trochlear dysplastic and normal knees. Both in the trochlear dysplastic tibial plateau and patella a narrower medial compartment leads to a significant smaller overall mediolateral width. These findings are important for the understanding of knee biomechanics and the design of total knee arthroplasty components.

LEVEL OF EVIDENCE

III.

Increased focal bone tracer uptake at the popliteus muscle origin in primary TKA compared with revision TKA

OBJECTIVE

The purpose of the study was to investigate if the TKA design (cruciate retaining (CR), posterior stabilized (PS), revision prostheses) had an influence on the bone tracer uptake (BTU) pattern at the origin of the popliteus muscle.

MATERIALS AND METHODS

A total of 92 knees (male:female = 46:46) which had undergone prior TKA were included in this retrospective study, comprising the following 3 groups: (i) CR primary TKA (n = 45); (ii) PS primary TKA (n = 24); (iii) revision TKA (n = 23). All patients received a SPECT/CT after TKA surgery. SPECT/CT images were reviewed for the presence of BTU in the lateral femoral condyle (origin of the popliteus muscle) by two observers using Syngo.via software (Siemens Healthcare, Erlangen, Germany). The observers recorded the BTU pattern qualitatively in the lateral femoral condyle as either (i) absent; (ii) present and diffuse; and (iii) present and focal in the region of the popliteus muscle origin.

RESULTS

In patients with a CR and PS design, focal increased BTU at the origin of the popliteus muscle was found in 80.0% and 83.3% respectively. Diffuse BTU was the predominant finding in patients with revision TKA (60.9%). The patterns of BTU did not show significant differences between the CR and the PS design. However, patterns of BTU differed significantly between primary TKA designs and revision TKA (p < 0.001).

CONCLUSION

Differences in patterns of BTU at the popliteus muscle origin between primary TKA and revision prosthesis may be the result of decreased insertional tensile forces of the popliteus muscle after revision surgery due to increased stability provided by the revision design.

Radiographs are not sufficient for evaluation of component fit in subtle knee pain after total knee arthroplasty

PURPOSE

To determine the component fit by radiography or computed tomography after total knee arthroplasty and the relation of imaging with clinical examination of residual knee pain.

METHODS

The study was conducted in 172 patients with residual knee pain after total knee arthroplasty. The patients were examined to determine whether they experienced pain upon palpation at nine regions surrounding the tibial and femoral components, and the results were noted. The Knee Society Clinical Rating System and The Western Ontario and McMaster Universities Arthritis Index pain scale score forms were completed for all patients. Radiologic evaluation was performed using computed tomography and anteroposterior, lateral, and oblique radiographs to determine component overhang/underhang status at these nine regions. Overhang, underhang, and cortical fit groups were created based on the position of the component at the bone margin. A statistical relationship was sought between the clinical scores and the values measured to determine which imaging method showed the best correlation with clinical scores. Consistency of CT and Rx measurements was compared using the McNemar-Bowker test. Comparisons between groups were made using Student's t test for normally distributed data, and the Mann-Whitney U test.

RESULTS

Computed tomography and radiographic measurements were similar in the medial, anterior, and lateral tibial regions. However, no similarities were observed in the anteromedial, anterolateral, posteromedial, and posterolateral tibial regions, and in the distal-medial and distal-lateral aspects of the femur. Statistical relationships among decreased clinical scores, pain with palpation, and the presence of overhang/underhang were only observed in the medial tibial region for imaging using radiography. A statistically significant relationship was observed in the medial, posteromedial, and posterolateral tibial regions, and in the distal-medial region of the femur for imaging based on computed tomography.

CONCLUSIONS

Radiography could only aid in assessing the component fit in the anteromedial, medial, and lateral regions of the tibia in patients with residual knee pain following knee arthroplasty, but it was not sufficient in comparison with computed tomography in six other regions.

LEVEL OF EVIDENCE

Prospective study, level of evidence II.

Biomechanical comparison of Thiel embalmed and fresh frozen nerve tissue

The aim of this study was to determine the effect of Thiel embalming on the biomechanical properties of nerve tissue, to validate the use of Thiel embalmed bodies as a reliable model system for obtaining biomechanical data to supplement neurodynamic models, for anesthesiological and neurosurgical training and for future preclinical test set-ups involving nerve tissue. Upon the arrival of a body at the anatomy department, a fresh median nerve was harvested, the harvest site was sutured and following the Thiel embalming procedure the Thiel embalmed median nerve of the opposing wrist was harvested. Micro CT was performed to establish the cross-sectional area and biomechanical tensile testing was performed to compare the Young's modulus/elasticity of fresh frozen and Thiel embalmed nerves. Thiel embalming did not cause a significant difference in elasticity when comparing Thiel embalmed and fresh frozen specimens. A correlation was found between the cross-sectional area of Thiel embalmed nerve specimens and their Young's modulus. Thiel embalming does not significantly alter the elasticity of nerve tissue compared to fresh frozen nerve tissue. Similar shapes were observed when comparing the stress/strain curves of both specimen types. This indicates that Thiel embalmed nerve tissue is a viable alternative for using fresh frozen specimens when investigating biomechanical principles/mechanisms. Some specimens showed a reversed trend in Young's modulus that could be related to slight differences in embalming outcome, so caution is advised when Thiel embalmed specimens are used to obtain raw numerical data for direct application in the clinic.

Iliotibial band friction syndrome after knee arthroplasty

Iliotibial band (ITB) friction syndrome is known to be one of the main causes of lateral knee pain related to an overuse injury. In the field of knee arthroplasty, ITB traction syndrome has been reported following guided motion total knee arthroplasty, due to posterior femoral translation and internal tibial rotation during knee flexion. However, ITB friction syndrome following conventional knee arthroplasty has not been reported. This paper reports four cases of this syndrome following conventional knee arthroplasty, mainly caused by an obstruction just under the ITB. Cases 1 and 2 presented extruded cement at the femoral component's lateral side after total knee arthroplasty. Case 3 presented a highly sharp-edged bearing at the lateral compartment after bicompartmental knee arthroplasty. Case 4 presented an osteophyte at the femoral component's lateral side after total knee arthroplasty. Although none of the cases responded well to conservative treatment, ITB friction syndrome was completely relieved just after excising the obstruction. Excision of an obstruction should be considered for ITB friction syndrome caused by obstruction just under the ITB following knee arthroplasty.

Sexual and ethnic polymorphism render prosthetic overhang and under-coverage inevitable using off-the shelf TKA implants

PURPOSE

Unexplained pain and stiffness after total knee arthroplasty (TKA) often result from mismatch between implant geometry and knee morphology, which depends on patient size, sex, and ethnicity. This study aimed to determine whether size, sex, or ethnicity are independently associated with distal femoral morphology in healthy Caucasian and Asian knees, and to compare anatomic ratios to those of commercially available TKA implants.

METHODS

Two series of computed tomography (CT) angiograms from France (264 knees) and China (259 knees) were used to digitize osteometric landmarks at the level of the femoral epicondyles, to measure anteroposterior (AP) and mediolateral (ML) dimensions at the anterior, posterior, medial, and lateral zones. The aspect (ML/AP), trapezoidicity (MLp/MLa), and asymmetry (APl/APm) ratios, as well as the sulcus angle were calculated and compared to those of 9 TKA models. Multivariable analyses were performed to determine whether anatomic ratios were independently associated with sex, origin, or size.

RESULTS

Multivariable analyses revealed that, independently from size, female knees were narrower (β = - 0.03; p < 0.001) and more asymmetric (β = 0.02; p < 0.001), while Chinese knees were more trapezoidal (β = 0.04; p = 0.002) and asymmetric (β = 0.02; p < 0.001) with shallower trochleae (β = 6.4°; p < 0.001). Compared to native knees, most implants were too wide, and many of the recent models too 'trapezoidal'. Most prosthetic trochleae were too shallow compared to French knees, but within the third quartile of Chinese knees.

CONCLUSIONS

The morphology of the distal femur depends on sex and ethnicity independently from size. The wide spectrum of morphotypes observed cannot be covered by 'off-the-shelf' TKA models, and until customized implants become more accessible, prosthetic overhang, and under-coverage remain inevitable.

LEVEL OF EVIDENCE

III, Retrospective comparative study.

Over-voluming predicted by pre-operative planning in 24% of total knee arthroplasty

PURPOSE

Numerous studies demonstrated that prosthetic overhang and over-sizing cause pain and stiffness following total knee arthroplasty (TKA), but none considered volume changes within the joint capsule. This study was designed to investigate differences in volumes of resected bone compared to implanted components in TKA, and to determine the incidence and factors related to 'over-voluming'.

METHODS

Three-dimensional reconstructions were created from 100 magnetic resonance imaging scans taken to design patient-specific instruments for TKA. The preoperative simulations were used to calculate the volume ratio (VR) by dividing volume of planned components by that of planned bone resections. Uni- and multi-variable linear regressions were performed to determine associations between 'over-voluming' (VR > 1.0) and gender, implant size and version (standard versus narrow), osteophytes, resection levels, external rotation of the femoral component, hip-knee-ankle (HKA) angle, mechanical lateral distal femoral angle (mLDFA), and mechanical medial proximal tibial angle (mMPTA).

RESULTS

The overall implant/bone volume ratio was 0.91 ± 0.11 (range 0.63-1.16) with 'over-voluming' observed in 24 knees. Multi-variable regression confirmed over-voluming to be associated with lower mLDFA (OR 0.66; CI 0.45-0.93; p = 0.026) and extensive osteophytes (OR 0.14; CI 0.03-0.61; p = 0.014), but not HKA angle (OR 0.98; CI 0.76-1.26; p = n.s.).

CONCLUSIONS

Over-voluming was observed in 24% of knees, in which the implant volume exceeded the resected volume by up to 16%. Over-voluming was associated with intra-articular femoral valgus (low mLDFA), but not directly associated with tibial deformity (mMPTA) or HKA angle. Over-voluming could be associated with prosthetic overhang or excessive tensions within the joint capsule, and, therefore, contribute to unexplained pain and stiffness following TKA.

LEVEL OF EVIDENCE

IV, Retrospective cohort study.

The original Akagi line is the most reliable: a systematic review of landmarks for rotational alignment of the tibial component in TKA

PURPOSE

There is no present consensus on the most reliable anatomical landmarks or axes for tibial rotational alignment in total knee arthroplasty (TKA). The goal was therefore to review the literature and compare accuracy and repeatability of different axes for tibial baseplate rotation in TKA.

METHODS

Medline and Embase were searched for articles that reported accuracy in terms of error or discrepancy from the trans-epicondylar axes (TEA), and/or repeatability in terms of intraclass correlation coefficient, of one or more axes used for tibial baseplate rotation in TKA. Twenty-one articles met criteria, and their data were extracted and tabulated.

RESULTS

The selected articles evaluated 15 different axes, 13 for reliability, 12 for repeatability. The lowest errors or discrepancies from the projected TEA were reported for the original 'Akagi line' (posterior cruciate ligament posteriorly to medial border of tibial tuberosity), its variant using the sulcus of the tibial spines as anterior landmark, as well as the anterior tibial border and the curve-on-curve technique. The best inter-observer repeatabilities were reported for 'Akagi line' variants that use the geometric centre of the tibial plateau posteriorly and the medial border of the tibial tuberosity, or the medial sixth of the patellar tendon anteriorly. Considering accuracy and repeatability simultaneously, only two axes were found to satisfy both criteria consistently: the original 'Akagi line' and the anterior tibial border.

CONCLUSIONS

Because of the small number of studies found, the collected evidence remains insufficient to recommend reference axes for intra-operative rotational alignment of the tibial baseplate in TKA. A combination of two or more anatomical landmarks or projected axes could be used to ensure adequate tibial baseplate rotation, while considering individual patient morphology and implant design to optimize knee kinematics and prevent prosthetic overhang.

LEVEL OF EVIDENCE

Level IV, systematic review of level III and IV studies.

Posterolateral overhang affects patient quality of life after total knee arthroplasty

PURPOSE

To investigate the appropriate mediolateral placement of symmetrical tibial components and the amount of overhang expected from the posterolateral of tibial components implanted to give ideal coverage and the subsequent incidence of residual knee pain and reduction in functional capacity.

METHOD

A retrospective evaluation was made of 146 consecutive total knee arthroplasties. The posterolateral overhang, rotational alignment and coverage of the tibial component were measured on a post-operative CT scan and the effect of posterolateral overhang on clinical outcomes was analysed 3 years after surgery.

RESULTS

Complaints of local pain in the posterolateral corner were determined in 76 (52.1%) patients. At the Posterolateral corner, overhang was determined in 111 (76%) patients, in the cortical border in 11 (7.6%) patients and underhang in 24 (16.4%) patients. In 71 (48.6%) patients, pain was determined together with oversize and in the evaluation of the overhang of the tibial component in the posterolateral region and the rotation status, there was determined to be overhang in 75 (96.2%) patients where the tibial component was placed in ideal rotation, in 25 (100%) where placement was in external rotation and in 11 (25.6%) where placement was in internal rotation. The mean KSS, KSS-F and WOMAC-P scores were 83.9 ± 6.3, 83.3 ± 7.8 and 4.6 ± 2.9, respectively, in those with posterolateral overhang of the tibial component .The mean KSS, KSS-F and WOMAC-P scores were 86.6 ± 8.4, 89.5 ± 7.8 and 2.8 ± 2.1, respectively, in those with no overhang and the difference was determined to be statistically significant. The amount of overhang was determined as mean 3.6 ± 2.0 mm in those with posterolateral pain and 0.02 ± 3.4 mm in those without pain and the difference was statistically significant.

CONCLUSIONS

This study demonstrated that overhang in the posterolateral region is surprisingly high and negatively affects the clinical results following TKA, thereby presenting a danger to the success of TKA. The risk of posterolateral oversizing can increase with placement of the tibial component in external rotation.