An analytical method for the simultaneous trace determination of acidic pharmaceuticals and phenolic endocrine disrupting chemicals in wastewater and sewage sludge by gas chromatography-mass spectrometry

Investigating the application of novel filling materials in Vertical Subsurface Flow Constructed Wetlands for the treatment of anaerobic effluents originating from domestic wastewater

Vertical subsurface flow constructed wetlands (VSSF CWs) were employed to investigate the use of biochar that could be produced with local agricultural biomass through pyrolysis, recycled glass from local recycling companies and gel beads with decreased packing volume and shipping cost as substrate alternatives to sand. The materials were assessed in terms of granulometry, porosity, adsorption capacity and hydraulic conductivity and were used for the treatment of an upflow anaerobic sludge blanket (UASB) reactor, treating domestic wastewater, effluent. Granulometry was a major factor impacting TSS removal that ranged from 81% ± 10% to 97% ± 2%. The COD removal was affected by granulometry, porosity and the active biofilm formation, since biochar removal was slightly higher (up to 93% ± 3%) than that of sand and recycled glass (up to 86% ± 4% and 85% ± 5%, respectively) and significantly higher than that of gel beads (up to 68% ± 8%). The higher porosity of biochar affected NH4-N removal in which adsorption had a greater and longer effect. The overall NH4-N removal ranged between 84% ± 11% and 99% ± 1% for all materials. Sand, biochar and glass achieved an 80% average removal of selected contaminants of emerging concern (CECs), including ibuprofen (IBU), naproxen (NPX), triclosan (TCS), bisphenol A (BPA), diclofenac (DCF) and ketoprofen (KFN). The biochar and recycled glass are effective in treating UASB effluent and enable the treated wastewater reuse, since, high compliance rates with the EU Regulation 2020/741 - Class A were achieved (>98% for TSS, >88% for BOD5 and 100% for turbidity).

Comparing the performance of microbial electrochemical assisted and aerated treatment wetlands in pilot-scale: Removal of major pollutants and organic micropollutants

The combination of treatment wetlands (TWs) with microbial electrochemical technologies (MET) is often studied in the lab to improve the performance and decrease the footprint of TWs. In this article we evaluated the long-term performance of four pilot-scale vertical sub-surface flow TWs for major pollutants' and organic micropollutants' removal from domestic wastewater. Three of them were filled with electroconductive material and operated under saturated (MET SAT), unsaturated (MET UNSAT) and unsaturated-saturated (MET HYBRID) conditions while the fourth one was a saturated intensified aerated system (AEW) filled with gravel. The MET-TWs achieved significant removals of COD (>78 %) with no clogging issues at the maximum applied OLR (249 g COD m-3 d-1) while under these loading conditions TSS removal exceeded 84 %. Among all electroactive TWs, UNSAT could remove 25 g NH4-N m-3 d-1 through nitrification when peak ammonium loading rate was applied; however this removal was significantly lower than AEW (35 g NH4-N m-3d-1). No important removal of P was observed in all systems with the exception of MET-SAT were precipitation reactions of P with iron occurred when anaerobic pretreated wastewater was used. The removal of the sum of studied organic micropollutants ranged between 70 ± 18 % (MET UNSAT) to 91 ± 4 % (AEW) and improved with feeding pulses increase. Moderate to high removal of specific microcontaminants was observed depending on the target compound, the studied system and the operational conditions. AEW and MET HYBRID systems complied with the limits set by EU for wastewater discharge to non-sensitive water bodies and for Class B water reuse. Scale-up calculations for a settlement of 500 PE showed that these systems require much less area per PE (0.51 m2 PE-1) comparing to conventional TWs while the operational cost was calculated to 0.07 € m-3 for the AEW and 0.02 € m-3 for the MET HYBRID.

Preparation and evaluation of Fe3O4@C@NiCo-LDH@CDs composites for magnetic solid-phase extraction of trace endocrine disruptors

The widespread use of endocrine disruptors (EDPs) has certain potential hazards to organisms and environments, and it is particularly important to develop effective pretreatment methods before detection of EDPs in complex samples. In this work, a novel magnetic nanocomposite decorated with layered double hydroxides (LDHs) and carbon dots (CDs) was designed and prepared for magnetic solid-phase extraction (MSPE) of EDPs (bisphenol S, bisphenol F, bisphenol A, bisphenol AF, diethylstilbestrol and 4-cumylphenol) combined with high-performance liquid chromatography-ultraviolet (HPLC-UV) detection. The prepared composites were characterized by field emission scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the adsorption mechanism towards these EDPs might be mainly based on hydrogen bonds and π-π conjugation. Under the optimized conditions, the proposed method showed limits of detection within 0.05-0.50 μg L-1 and limits of quantitation within 0.2-2.0 μg L-1, and good linearity (R2 ≥ 0.9975) was presented in the range of 0.2-200 μg L-1. Finally, the Fe3O4@C@NiCo-LDH@CDs composite-based MSPE-HPLC-UV method was applied for enrichment and determination of EDPs in water, milk, and tea beverage samples with recoveries in the range of 81.2-119.8% and relative standard deviations below 9.7%.

Occurrence of selected antibiotics in urban rivers in northwest Pakistan and assessment of ecotoxicological and antimicrobial resistance risks

Antibiotics in aquatic systems of developing countries are a growing concern, particularly with the potential ecological risks and emergence of antimicrobial resistance. In Pakistan, antibiotics are widely consumed and released untreated into rivers, however, there is little information on their occurrence and potential risks. In this study, the concentrations and risk assessment of three commonly consumed antibiotics, ciprofloxacin (CIP), amoxicillin (AMX), and cefixime (CFM) belonging to different classes of fluoroquinolone, penicillin, and cephalosporin respectively were investigated in the Kabul River and its two tributaries, Bara River and Shah Alam River in the northwest region of the country. Composite samples were collected in different sampling campaigns and analyzed using the LC-ESI-MS/MS technique. All three antibiotics were found in higher concentrations ranging from 410 to 1810 ng/L, 180-850 ng/L, and 120-600 ng/L for CIP, AMX, and CFM respectively. The Friedman and Wilcoxon signed-ranked tests revealed insignificant differences in average concentrations of each antibiotic in the three rivers and the Pearson Correlation showed a significant positive correlation of CIP with both AMX and CFM indicating their similar pollution sources. Ecotoxicological risk assessment showed a higher risk to algae and bacteria (P. putida) in the rivers with CIP posing a greater risk. The potential risk of antimicrobial resistance development (ARD) was higher in all the three rivers, particularly in Kabul River where maximum risk quotients (RQARD) of 28.3, 9.4 and 3.4 were noted for CIP, CFM and AMX respectively. The human health (HH) risk was insignificant, though the RQHH was higher for the lower age groups (0-3 months). In addition, the combined flux of the antibiotics in the Kabul River was estimated as 59 tons/year with CIP having a significant flux relative to the other antibiotics.

Evaluating an integrated nano zero-valent iron column system for emerging contaminants removal from different wastewater matrices - Identification of transformation products

The presence of micropollutants in water bodies has become a growing concern due to their persistence, bioaccumulation and potential toxicological effects on aquatic life and humans. In this study, the performance of a column system consisting of zero-valent iron nanoparticles (nZVI) incorporated into a cationic resin and synthesized from green tea extract with the addition of persulfate for the elimination of selected pharmaceuticals and endocrine disruptors from wastewater is evaluated. Ibuprofen, naproxen, diclofenac and ketoprofen were the target pharmaceuticals from non-steroidal anti-inflammatory drugs group, while bisphenol A was the target endocrine disruptor. In this context, different real wastewater effluent matrices were investigated: anaerobic membrane bioreactor (AnMBR), upflow anaerobic sludge blanket reactor (UASB) after microfiltration, tertiary treated by conventional activated sludge system and saturated vertical constructed wetland followed by a sand filtration unit effluent (hybrid). The transformation products of diclofenac and bisphenol A were also identified. The experimental results indicated that the performance of the R-nFe/PS system towards the removal efficiency of the target compounds was enhanced in the order of effluents: tertiary > AnMBR ≈ hybrid > UASB. More than 70% removal was obtained for almost all target compounds when conventional tertiary effluent was used, while the maximum removal efficiency was about 50% in the case of filtered UASB. As far as we know, this is the first time that nZVI has been assessed in combination with persulfate for the removal of micropollutants in a continuous flow system receiving various types of real wastewater with different matrix characteristics.

Simultaneous determination of the free and total forms of nonylphenol, nonylphenol monoethoxylate, and nonylphenol diethoxylate in human urine by gas chromatography-mass spectrometry

Nonylphenol (NP), nonylphenol monoethoxylate (NP1EO), and nonylphenol diethoxylate (NP2EO) are widely used in various daily products and have been cataloged as endocrine-disrupting chemicals. Due to their high lipophilicity and low biodegradability, these compounds remain in the environment and enter the human body through the food chain. Growing concerns regarding the potential negative effects of NP, NP1EO, and NP2EO on human health have raised the need for biomonitoring to investigate human exposure to these compounds. In this study, a simultaneous analysis method using solid-phase extraction (SPE) combined with gas chromatography-mass spectrometry (GC-MS) was established by controlling the background contamination of NP, NP1EO, and NP2EO, which are ubiquitous in laboratory environments. The proposed method showed proper linearity of over 0.999 and a recovery greater than 85.8% for all analytes. Accuracy and precision were verified in ranges of 92.97-116.30% and 0.65-9.29%, respectively. The detection limits for NP, NP1EO, and NP2EO were 0.0363 μg L-1, 0.0401 μg L-1, and 0.0364 μg L-1, respectively, which were suitable for determining the trace analytes in human urine. Therefore, this simple and integrated analytical method was applied to measure the free and total forms of the target analytes in 25 human urine samples collected in Korea. Overall, free NP, NP1EO, and NP2EO were detected with average contents of 3.94 ± 4.14 μg L-1, 4.63 ± 2.62 μg L-1, and 0.293 ± 0.638 μg L-1, respectively, and with total NP, NP1EO, and NP2EO contents of 6.14 ± 8.24 μg L-1, 5.99 ± 2.91 μg L-1, and 0.806 ± 1.10 μg L-1, respectively. These data showed that these compounds are prevalent in human urine, and indicate the need for further studies.

Understanding the role of sorption and biodegradation in the removal of organic micropollutants by membrane aerated biofilm reactor (MABR) with different biofilm thickness

The role of sorption and biodegradation in a membrane aerated biofilm reactor (MABR) were investigated for the removal of 10 organic micropollutants (OMPs) including endocrine disruptors and pharmaceutical active compounds. The influence of the biofilm thickness on the mechanisms of removal was analyzed via kinetic test at three different stages. At all biofilm stages, biodegradation was demonstrated to dominate the removal of selected OMPs. Higher OMPs rates of removal via biodegradation (K_biol) were achieved when biofilm increased its thickness from (stage T1) 0.26 mm, to (stage T2) 0.58 mm and (stage T3) 1.03 mm. At stage T1 of biofilm, heterotrophs contribute predominantly to OMPs degradation. Hydrophilic compounds removal (i.e., acetaminophen) continue to be driven by heterotrophic bacteria at the next stages of biofilm thickness. However, for medium hydrophobic neutral and charged OMPs, the combined action of heterotrophic and enriched nitrifying activity at stages T2 and T3 enhanced the overall removal. A degradation pathway based on heterotrophic activity for acetaminophen and combined action of nitrifiers-heterotrophs for estrone was proposed based on identified metabolites. Although biodegradation dominated the removal of most OMPs, sorption was also observed to be essential in the removal of biologically recalcitrant and lipophilic compounds like triclosan. Furthermore, sorption capacity of apolar compound was enhanced as the biofilm thickness grew and increased in EPS protein fraction. Microbial analysis confirmed the higher abundance of nitrifying and denitrifying activity at stage T3 of biofilm, which not only facilitated near complete ammonium removal but also enhanced degradation of OMPs.

Triclosan and related compounds in the environment: Recent updates on sources, fates, distribution, analytical extraction, analysis, and removal techniques

Triclosan (TCS) has been widely used in daily life because of its broad-spectrum antibacterial activities. The residue of TCS and related compounds in the environment is one of the critical environmental safety problems, and the pandemic of COVID-19 aggravates the accumulation of TCS and related compounds in the environment. Therefore, detecting TCS and related compound residues in the environment is of great significance to human health and environmental safety. The distribution of TCS and related compounds are slightly different worldwide, and the removal methods also have advantages and disadvantages. This paper summarized the research progress on the source, distribution, degradation, analytical extraction, detection, and removal techniques of TCS and related compounds in different environmental samples. The commonly used analytical extraction methods for TCS and related compounds include solid-phase extraction, liquid-liquid extraction, solid-phase microextraction, liquid-phase microextraction, and so on. The determination methods include liquid chromatography coupled with different detectors, gas chromatography and related methods, sensors, electrochemical method, capillary electrophoresis. The removal techniques in various environmental samples mainly include biodegradation, advanced oxidation, and adsorption methods. Besides, both the pros and cons of different techniques have been compared and summarized, and the development and prospect of each technique have been given.

β-cyclodextrin-functionalized magnetic graphene oxide for the efficient enrichment of bisphenols in milk and milk packaging

In this work, β-cyclodextrin-functionalized magnetic graphene oxide (NiFe₂O₄@GO@β-CD) was synthesized and employed as magnetic solid-phase extraction adsorbent for the extraction of bisphenols before high performance liquid chromatography analysis. The modification of β-cyclodextrin could enhance the adsorption performance of NiFe₂O₄@GO@β-CD towards bisphenols through the host-guest interaction and hydrogen-bond interaction. Under the optimal conditions, good linearities between peak area and concentration of bisphenols (1 - 300 μg L^-1, r ≥ 0.9989) were obtained with the limits of detection (S/N = 3) in the range of 0.050 - 0.10 μg L^-1. The recoveries of bisphenols in milk and milk packaging ranged from 78.0% to 101.6%. Moreover, NiFe₂O₄@GO@β-CD showed stable chemical properties and good reusability with the recoveries of bisphenols remained above 80.0% after 12 MSPE cycles. The adsorption characteristics of NiFe₂O₄@GO@β-CD towards bisphenols fitted well with the pseudo-second-order kinetic model and Langmuir model. The hydrogen-bond interaction, π-π interaction, host-guest interaction and electrostatic interaction between sorbent and bisphenols played important role during the adsorption process. The developed method showed potential applications for the analysis of trace bisphenols in milk and milk packaging.

Pharmaceutical pollution of hospital effluents and municipal wastewaters of Eastern Canada

Quantification of drugs residues in wastewaters of different sources could help better understand contamination pathways, eventually leading to effluent regulation. However, limited data are available for hospital-derived wastewaters. Here, an analytical method based on automated on-line solid-phase extraction liquid chromatography tandem mass spectrometry (on-line SPE - UPLC-MS/MS) was developed for the quantification of multi-class pharmaceuticals in wastewaters. Filtrate phase and suspended solids (SPM) were both considered to evaluate the distribution of targeted analytes. Experimental design optimization involved testing different chromatographic columns, on-line SPE columns, and loading conditions for the filtrate phase, and different organic solvents and cleanup strategies for suspended solids. The selected methods were validated with suitable limits of detection, recovery, accuracy, and precision. A total of 30 hospital effluents and 6 wastewater treatment plants were sampled to evaluate concentrations in real field-collected samples. Certain pharmaceuticals were quantified at high levels such as caffeine at 670,000 ng/L in hospital wastewaters and hydroxyibuprofen at 49,000 ng/L in WWTP influents. SPM samples also had high contaminant concentrations such as ibuprofen at 31,000 ng/g in hospital effluents, fluoxetine at 529 ng/g in WWTP influents or clarithromycin at 295 ng/g in WWTP effluents. Distribution coefficients (K_d) and particle-associated fractions (Φ) indicate that pharmaceuticals tend to have better affinity to suspended solids in hospital wastewater than in municipal wastewaters. The results also bring arguments for at source treatment of these specific effluents before their introduction into urban wastewater systems.

Influence of biofilm thickness on the removal of thirteen different organic micropollutants via a Membrane Aerated Biofilm Reactor (MABR)

The presence of organic micropollutants (OMPs) in natural water bodies has become an emerging concern due to their fast dissemination into natural water sources, high persistence, ubiquitous nature, and detrimental impact on the environment and human health. This study evaluated the Membrane Aerated Biofilm Reactor (MABR) efficiency in the removal of 13 OMPs commonly reported in water. Results demonstrated that OMPs removal is dependent on biofilm thickness and bacterial cell density, microbial community composition and physicochemical properties of OMPs. Effective removals of ammonium and organic carbon (COD, >50%), acetaminophen (70%) and triclosan (99%) were obtained even at early stages of biofilm development (thickness < 0.33 mm, 2.9 ×10⁵ cell mL^-1). An increase in biofilm thickness and cell density (1.02 mm, 2.2 ×10⁶ cell mL^-1) enhanced the system performance. MABR achieved over 90% removal of nonpolar, hydrophobic and hydrophilic OMPs and 22-69% removal of negatively charged and acidic OMPs. Relative abundances of Zoogloea, Aquabacterium, Leucobacter, Runella, and Paludilbaculum bacteria correlated with the removal of certain OMPs. In addition, MABR achieved up to 96% nitrification and 80% overall COD removal by the end of the experiment. The findings from this study demonstrated MABRs to be a feasible option to treat municipal wastewater polluted by OMPs.

Assessment of the occurrence of 455 pharmaceutical compounds in sludge according to their physical and chemical properties: A review

Sludge agronomical reuse is of major interest due to the beneficial contribution of nutrients. However, it implies the introduction of unregulated pharmaceuticals into amended-soils and creates a controversial issue about sludge management. To limit their dissemination, it is essential to identify the compounds of interest and understand their attenuation mechanisms through the sludge processes. This paper summarizes the knowledge on 455 investigated pharmaceuticals among 32 therapeutical categories in amendable sludge matrices. It contributes to enlarging the list of commonly quantified compounds to 305 residues including 84 additional compounds compared to previous reviews. It highlights that sorption appears as the main mechanism controlling the occurrence of pharmaceuticals in sludge matrices and shows the considerable residual levels of pharmaceuticals reaching several mg/kg in dry weight. Antibiotics, stimulants, and antidepressants show the highest concentrations up to 232 mg/kg, while diuretics, anti-anxieties or anticoagulants present the lowest concentrations reaching up to 686 µg/kg. Collected data show the increase in investigated compounds as antifungals or antihistamines, and underline emerging categories like antidiabetics, antivirals, or antiarrhythmics. The in-depth analysis of the substantial database guides onto the pharmaceuticals that are the most likely to occur in these amendable matrices to assist future research.

Quadruple isotope dilution gas chromatography-mass spectrometry after simultaneous derivatization and spraying based fine droplet formation liquid phase microextraction method for the accurate and sensitive quantification of chloroquine phosphate in human serum, urine and saliva samples at trace levels

This study presents an accurate and precise analytical strategy for the determination of chloroquine phosphate at trace levels in human body fluids (urine, serum, and saliva). Simultaneous derivatization-spraying based fine droplet formation-liquid phase microextraction (SD-SFDF-LPME) method was used to derivatize and preconcentrate the analyte prior to gas chromatography-mass spectrometry (GC-MS) measurements. Acetic anhydride was employed as derivatizing agent in this study. After optimizing the SD-SFDF-LPME method, the limit of detection (LOD) and limit of quantitation (LOQ) were found to be 0.16 and 0.53 mg/kg, respectively. Quadruple isotope dilution (ID⁴) was coupled to the SD-SFDF-LPME method in order to alleviate matrix effects and promote accuracy/precision of the method. Chloroquine acetamide-d3 was firstly synthesized in our research laboratory and used as the isotopic analogue of the analyte in the ID⁴ experiments. Superior percent recovery results (99.4% - 101.0%) with low standard deviation values were obtained for the spiked samples. This validated the developed SD-SFDF-LPME-ID⁴-GC-MS method as highly accurate and precise for the determination of chloroquine phosphate at trace levels. In addition, the isotopic analogue of the analyte was obtained via the acetamide derivative of the analyte, which is an alternative to obtain isotopic analogues of organic compounds that are not accessible or commercially available.

Ecotoxicity and biodegradation of the bacteriostatic 3,3',4',5-tetrachlorosalicylanilide (TSCA) compared to the structurally similar bactericide triclosan

This article studies the ecotoxicity of 3,3',4',5-tetrachlorosalicylanilide (TCSA) using different bioassays and examines its fate in activated sludge batch experiments. Despite of the common use of TCSA as chemical uncoupler in wastewater treatment systems and as preservative in several products, limited data has been published for its ecotoxicity, while no information is available for its biodegradation. Among different bioassays, the highest toxicity of TSCA was noticed for Daphna magna (48-h LC₅₀: 0.054 mg L^-1), followed by Vibrio fischeri (15-min EC₅₀: 0.392 mg L^-1), Lemna minor, (7-d EC₅₀: 5.74 mg L^-1) and activated sludge respiration rate (3-h EC₅₀: 31.1 mg L^-1). The half-life of TSCA was equal to 7.3 h in biodegradation experiments with activated sludge, while use of mass balances showed that 90% of this compound is expected to be removed in an aerobic activated sludge system, mainly due to biodegradation. A preliminary risk assessment of TSCA using the Risk Quotient methodology showed possible ecological threat in rivers where wastewater is diluted up to 100-fold. Comparison with the structurally similar 5-chloro-2-(2,4-dichlorophenoxy)phenol (triclosan, TCS) showed that both compounds have similar biodegradation potential and seem to cause analogous toxicity to Vibrio fischeri and activated sludge. Specifically, TCS was biodegraded quite rapidly by activated sludge (half-life: 6.2 h), while EC₅₀ values equal to 0.134 mg L^-1 and 39.9 mg L^-1 were calculated for Vibrio fischeri, and activated sludge respiration rate. Future research should focus on monitoring of TSCA concentrations in the environment and study its effects in long-term toxicity and bioaccumulation tests.

Possible overestimation of bisphenol analogues in municipal wastewater analyzed with GC-MS

This work for the first time showed that sulfated BPA could be directly analyzed as BPA with GC-MS after the derivatization with N,O-bis-(trimethylsilyl) trifluoroacetamide (BSTFA)+1% trimethylchlorosilane (TMCS), i.e. the deconjugation step was not necessary. This was because sulfated BPA indeed could be simultaneously deconjugated and derivatized to BPA derivative during derivatization, suggesting that any co-elution of BPA and sulfated BPA during sample extraction led to BPA overestimation in the GC-MS method with BSTFA +1% TMCS as the derivative reagent. Using BPA 4,4'-disulfates (BPA diS) as the pure standard, the co-elution phenomena of sulfated BPA was confirmed with two widely used elution solvents (i.e. methanol and ethyl acetate) or their mixed solutions with different ratios, which further suggested if only sulfated BPA existed in any wastewater sample, BPA was likely over-determined. To further confirm this finding, both influent and effluent samples collected from a local municipal wastewater treatment plant were analyzed, which clearly showed the overestimation of BPA in the two wastewaters due to co-existence of sulfated BPA in the wastewater samples. In addition to BPA, the results also showed the overestimation of other nine bisphenol analogues. As sulfated micropollutants including estrogens, androgens, phytoestrogens, etc., have been widely found in municipal wastewater, the overestimating phenomenon observed in this study may also be extended to determination of other micropollutants, which should be addressed in future.

Fate of Emerging Contaminants in High-Rate Activated Sludge Systems

High-rate activated sludge (HRAS) systems are designed to shift the energy-intensive processes to energy-saving and sustainable technologies for wastewater treatment. The high food-to-microorganism (F/M) ratios and low solid retention times (SRTs) and hydraulic retention times (HRTs) applied in HRAS systems result in the maximization of organic matter diversion to the sludge which can produce large amounts of biogas during anaerobic digestion, thus moving toward energy-neutral (or positive) treatment processes. However, in addition to the energy optimization, the removal of emerging contaminants (ECs) is the new challenge in wastewater treatment. In the context of this study, the removal efficiencies and the fates of selected ECs (three endocrine disruptors (endocrine disrupting chemicals (EDCs))—nonylphenol, bisphenol A and triclosan, and four pharmaceuticals (PhACs)—ibuprofen, naproxen, diclofenac and ketoprofen) in HRAS systems have been studied. According to the results, EDCs occurred in raw wastewater and secondary sludge at higher concentrations compared to PhACs. In HRAS operating schemes, all compounds were poorly (<40%) to moderately (<60%) removed. Regarding removal mechanisms, biotransformation was found to be the dominant process for PhACs, while for EDCs sorption onto sludge is the most significant removal mechanism affecting their fates and their presence in excess sludge.

Construction waste as substrate in vertical subsuperficial constructed wetlands treating organic matter, ibuprofenhene, acetaminophen and ethinylestradiol from low-strength synthetic wastewater

This study aimed to evaluate the removal of chemical oxygen demand (COD), total Kjeldahl nitrogen (TKN), total ammonia nitrogen (TAN), total phosphorus (TP), ibuprofen, acetaminophen and ethinylestradiol of synthetic effluent simulating low-strength sewage by sequencing-batch mode constructed wetlands (CWs). To verify the feasibility of using a floating macrophyte in CWs and compare different substrates, three CWs containing light expanded clay aggregates (CWL), expanded clay with porcelain tiles (CWLP) and bricks (CWB) were planted with Pistia stratiotes. The results showed that CWB achieved the highest removals of TKN (78%), TAN (70%) and TP (46%), and CWLP achieved the highest COD removal (75%). LECA favored the removal of ibuprofen (92%, p < 0.05) when compared to bricks (77%), probably by the combination of biodegradation and sorption in the systems. The highest acetaminophen removal (71% to 96%) was observed in CWL, probably via biodegradation, but no significant differences were found between the CWs (p > 0.05). Ethinylestradiol was removed 76% in CWLP and 73% in CWB, both differing statistically from CWL (p < 0.05), demonstrating that brick and the combination of clay with porcelain were better than just clay in this hormone removal. After 188 days of operation, P. stratiotes was able to uptake nitrogen and phosphorus of approximately 0.28 g and 0.25 g in CWL, 0.33 g and 0.21 g CWLP, and 0.22 g and 0.09 g in CWB of, respectively. Adsorption of nitrogen and phosphorus onto the substrates was 0.48 g and 6.84 g in CWL, 0.53 g and 5.69 g in CWLP, and 0.36 g and 10.18 g in CWB, respectively. The findings on this study suggest that adsorption was possible the main process for TP removal onto the evaluated substrates whereas microbial activity was the most probable mechanism for TN removal in the evaluated CW systems.

A novel technique for simultaneous determination of drugs using magnetic nanoparticles based dispersive micro-solid-phase extraction in biological fluids and wastewaters

In this study, a novel method was developed to measure acidic and basic drugs in biological and wastewater samples. The method used magnetic nanoparticles based on Vortex-Assisted Dispersive Micro-Solid Phase Extraction (SPE) and then identifying with HPLC-UV. The magnetic nanoparticle (Fe₃O₄@SiO₂@Kit-6@NH₂) has been used as an efficient adsorbent for the extraction of acidic and basic drugs ibuprofen (IFB), fenoprofen calcium (FPC), methocarbamol (MTC), and clonazepam (CZP). The magnetic nanoparticle was characterized by techniques including SEM, XRD, EDX, and FT-IR. The effect of various parameters in the V-D-μ-SPE method was studied completely through the design of the response surface methodology (RSM) of the Box–Behnken design (BBD) based response method and the utility function. The parameters affecting the extraction efficiency were optimized including sample pH, adsorbent amount, absorption time, the salt concentration in the sample solution, CTAB of concentration, desorption time, and the volume of an eluent. After optimization, the limit of detection and calibration curve in the linear range were obtained 0.062–0.32 μg L⁻¹ and 0.1–800 μg L⁻¹, respectively. Its linear correlation was R²> 0.9951. The relative standard deviation (n = 5) was between 2.4% and 5.1%. Finally, this method was used to determine target analytes in human serum, urine, and wastewater.•

In this study, for the first time, a novel method for the determination of some drugs from human serum, urine, and wastewater samples.

•

The Synthesized Fe₃O₄@SiO₂@Kit-6@NH₂ NPs based V-D-μ-SPE was characterized by techniques including SEM, XRD, EDX, and FT-IR.

•

The effects of various parameters in the V-D-μ-SPE methods were studied through the design of the RSM of BBD.

Factorial Design Optimisation of Solid Phase Extraction for Preconcentration of Parabens in Wastewater Using Ultra-High Performance Liquid Chromatography Triple Quadrupole Mass Spectrometry

Background:

Parabens are synthetic esters used extensively as preservatives and/or bactericides in personal care personal products.

Objective:

Development and validation of a novel robust chemometric assisted analytical technique with superior analytical performances for the determination of ethylparaben, methylparaben and propylparaben, using simulated wastewater matrix.

Methods:

An automated Solid Phase Extraction (SPE) method coupled with liquid chromatographymass spectrometry was applied in this study. A gradient elution programme comprising of 0.1% formic acid in deionised water (A) and 0.1% formic acid in Methanol (B) was employed on a 100 x 2.1 mm, 3.0 μm a particle size biphenyl column. Two-level (2k) full factorial design coupled with response surface methodology was used for optimisation and investigation of SPE experimental variables that had the most significant outcome of the analytical response.

Results:

According to the analysis of variance (ANOVA), sample pH and eluent volume were statistically the most significant parameters. The method developed was validated for accuracy, precision, Limits of Detection (LOD) and Limit of Quantification (LOQ) and linearity. The LOD and LOQ established under those optimised conditions varied between 0.04-0.12 μgL−1 and 0.14-0.40 μgL−1 respectively. The use of matrix-matched external calibration provided extraction recoveries between 78-128% with relative standard deviations at 2-11% for two spike levels (10 and 100 μgL-1) in three different water matrices (simulated wastewater, influent and effluent water).

Conclusion:

The newly developed method was applied successfully to the analyses of parabens in wastewater samples at different sampling points of a wastewater treatment plant, revealing concentrations of up to 3 μgL−1.

Occurrence, removal and seasonal variation of pharmaceuticals in Brasilian drinking water treatment plants

The presence of pharmaceuticals in aquatic environments has become a major issue of concern for scientific community, since there is a lack of information about risks and impacts to the environment and public health. In the context of Brazil, many cities do not have Wastewater Treatment Plants (WWTPs) and domestic sewage is dumped directly into the water bodies, aggravating the problem. Thus, the present study aimed to evaluate the presence of 28 prescribed pharmaceuticals from different therapeutic classes in six full-scale Drinking Water Treatment Plants (DWTPs) in Minas Gerais state. Samples were collected in twelve field campaigns from August 2016 to August 2017 and water quality were monitored. Analytical methodology was based on solid phase extraction (C18 cartridge) followed by High Performance Liquid Chromatography (Prominence DGU/20A3 - Shimadzu) coupled to Mass Spectrometry (micrOTOF-QII - Bruker). Considering the 28 pharmaceuticals analyzed, 18 were detected in the surface water source at concentrations ranging from Method Quantification Limit (MQL) to 11,960 ng/L. In drinking water, the concentration of the 11 pharmaceuticals detected ranged from <MQL to 6323 ng/L. Betamethasone, Fluconazole, Atorvastatin and Prednisone were the most detected pharmaceuticals. The drinking water monitoring showed a decrease in the concentration of all detected pharmaceuticals, indicating some removal of these compounds by the water treatment processes. The removal efficiency assessed shows a great variation among different compounds, DWTPs and over the year, ranging from an average of 32% ± 6% (Prednisone -DWTP3) to 100% ± 0% for some pharmaceuticals. The highest total concentrations and the maximum concentration values for the most frequently detected pharmaceuticals were related to the winter due, presumably, to lower dilution and temperature. Trace levels of pharmaceuticals were detected in surface and drinking water in Brazil and conventional DWTPs were not able to remove the pharmaceuticals completely.

Analytical and mathematical assessment of emerging pollutants fate in a river system

The fate of several emerging pollutants in a Greek river system was assessed through analytical measurements and mathematical modelling. Target compounds selected in this study consist of five endocrine disrupting chemicals and four non-steroidal anti-inflammatory drugs. Two sampling campaigns were implemented to assess target compounds concentrations along the river system during dry period. Furthermore a mathematical model was developed in order to simulate the spatial distribution of target compounds concentration. The mathematical model describes several abiotic and biotic processes (sorption, photodegradation, biodegradation, biotransformation) in order to account for the removal of target compounds. Following sensitivity analysis, the model was calibrated and validated against measured values. Environmental risk assessment was performed based on both analytical measurements and simulation results. Uncertainty analysis was also conducted by applying Monte Carlo technique. According to the results the simulation data matched very satisfactorily with the analytical measurements, thus confirming the main experimental observations showing that the primary removal mechanism for the photo-sensitive chemicals is photodegradation, the latter being mostly influenced by weather conditions and river general quality characteristics (e.g. chlorophyll, turbidity). Model results demonstrate a gradual increase of uncertainty from the upstream to the downstream of the river system for all target compounds.

Removal of micro-pollutants from urban wastewater by constructed wetlands with Phragmites australis and Salix matsudana

This study assessed the ability to remove micro-pollutants from wastewater using herbaceous species (Phragmites australis L.) and trees (Salix matsudana Koidz.) in constructed wetland (CW) systems. The targets of the study were as follows: (i) pharmaceuticals like diclofenac, ketoprofen, and atenolol; (ii) 4-n-NP (4-n-nonylphenol) and the ethoxylated derivatives monoethoxylated nonylphenol (NP₁EO) and diethoxylated nonylphenol (NP₂EO); (iii) triclosan, a bactericide used in personal care products. The 12 CW systems, filled with clay and gravel, were irrigated with wastewater from municipal area of Pagnana (Tuscany, Italy) and influent and effluent water samples analyzed periodically by gas chromatography-mass spectrometry (GC-MS/MS). The removal efficiency of CWs planted with willow and common red ranged from 8.4 up to 100%, with the higher removal efficiency for triclosan. On the contrary, the removal efficiency of NPs and NPEOs appears lower than pharmaceuticals. Data demonstrated that P. australis efficiently removed NP, diclofenac, and atenolol, while S. matsudana preferentially removed NP₁EO, NP₂EO, ketoprofene, and triclosan. A specific selection of plants used in CWs could be exploited for the removal of specific xenobiotics from wastewater.

Fabrication of calixarene-grafted bio-polymeric magnetic composites for magnetic solid phase extraction of non-steroidal anti-inflammatory drugs in water samples

Calixarene framework functionalized bio-polymeric magnetic composites (MSp-TDI-calix) were synthesized and utilized as magnetic solid-phase extraction (MSPE) sorbent for the extraction of non-steroidal anti-inflammatory drugs (NSAIDs), namely indoprofen (INP), ketoprofen (KTP), ibuprofen (IBP) and fenoprofen (FNP), from environmental water samples. MSp-TDI-calix was characterized by FT-IR, XRD, FESEM, EDX, VSM and BET analysis, and the results were compared with Sp-TDI and Sp-TDI-calix. To maximize the extraction performance of MSp-TDI-calix decisive MSPE affective parameters such as sorbent amount, extraction time, sample volume, type of organic eluent, volume of organic eluent, desorption time and pH were comprehensively optimized prior to HPLC-DAD determination. The analytical validity of the proposed MSPE method was evaluated under optimized conditions and the following figures of merit were acquired: linearity with good determination coefficient (R² ≥ 0.991) over the concentration range of 0.5–500 µg/L, limits of detection (LODs) ranged from 0.06–0.26 µg/L and limits of quantitation (LOQ) between 0.20–0.89 µg/L. Excellent reproducibility and repeatability under harsh environment with inter-day and intra-day relative standard deviations were obtained in the range of 2.5–3.2% and 2.4–3.9% respectively. The proposed method was successfully applied for analysis of NSAIDs in tap water, drinking water and river water with recovery efficiency ranging from 88.1–115.8% with %RSD of 1.6–4.6%.

Assessment of the environmental fate of endocrine disrupting chemicals in rivers

Laboratory tests were conducted with five endocrine disruptors (bishenol A, triclosan. nonylphenol, nonylphenol monoethoxylate and nonylphenol diethoxylate) under different redox conditions (aerobic, anoxic, anaerobic and sulfate-reducing conditions) to assess abiotic and biotic degradation in a river water/sediment system. The river water sample was collected from Spercheios River while the sediment was collected from the banks of a tributary of the river at the point where the discharge point of a wastewater treatment plant is located. To describe quantitatively elimination kinetics of the target compounds, pseudo first-order kinetics were adopted. According to the results from the microcosms studies, it can be stated that the substances are eliminated from the aqueous phase with relatively high rates under aerobic conditions due to both sorption and biotransformation processes. However, when reduced oxygen conditions were established in the microcosms incubations, biotransformation decreased, indicating the almost complete cease of the EDCs microbial degradation, while substances' sorption onto sediments showed no significant differences. All compounds were found to be biodegradable under aerobic conditions, and the low to high order of the calculated dissipation rate constants was 0.064±0.004d^-1 (TCS)→0.067±0.006d^-1 (NP)→0.076±0.009d^-1 (NP2EO)→0.081±0.007d^-1 (NP1EO)→0.103±0.011d^-1 (BPA). Finally, regarding the biotransformation experiments, the elimination of the compounds limited in the absence of oxygen as compared to aerobic.

Greywater characterization and loadings - Physicochemical treatment to promote onsite reuse

Greywater is the wastewater produced in bathtubs, showers, hand basins, kitchen sinks, dishwashers and laundry machines. Segregation of greywater and blackwater and on site greywater treatment in order to promote its reuse for toilet flushing and/or garden irrigation is an interesting option especially in water deficient areas. The objective of this study was to characterize the different greywater sources in Greek households and to evaluate the performance of alternative physicochemical treatment systems to treat several types of greywater. Based on the results average daily greywater production was equal to 98 L per person per day and accounts for approximately 70-75% of the total household wastewater production (135 L per person per day). Among the different sources, laundry and kitchen sink are the main contributors to the total greywater load of organic carbon, suspended solids and surfactants, whereas dishwasher and bathroom greywater are the main sources of phosphorus and endocrine disrupting chemicals respectively. Depending on sources, greywater accounts for as low as 15% of the total wastewater load of organic carbon (in the case of light greywater sources), to as high as 74% of the total load organic load (in the case of the heavy greywater sources). On the other hand, the nutrients load of greywater is limited. The application of a physical treatment system consisting of coagulation, sedimentation, sand filtration, granular activated carbon filtration and disinfection can provide for a final effluent with high quality characteristics for onsite reuse, especially when treating light greywater.

Evaluation of alternative environmentally friendly matrix solid phase dispersion solid supports for the simultaneous extraction of 15 pesticides of different chemical classes from drinking water treatment sludge

This study describes the development, optimization and validation of a method for the extraction of 15 pesticides of different chemical classes in drinking water treatment sludge (DWTS) by vortex-assisted Matrix Solid Phase Dispersion (MSPD) with determination by gas chromatography coupled to mass spectrometry. It focused on the application of alternative and different solid supports to the extraction step of the MSPD. The main parameters that influenced the extraction were studied in order to obtain better recovery responses. Recoveries ranged from 70 to 120% with RSD below 20% for all analytes. Limits of quantification (LOQ) of the method ranged from 5 to 500 μg kg^-1 whereas the analytical curves showed correlation coefficients above 0.997. The method under investigation used low volume of solvent (5 mL), low sample mass (1.5 g) and low mass of chitin (0.5 g), an environmentally friendly support. It has advantages, such as speed, simplicity and low cost material, over other methods. When the method was applied, 4 out of 15 pesticides were detected in the DWTS samples in concentrations below the LOQ.

Environmental fate of non-steroidal anti-inflammatory drugs in river water/sediment systems

Laboratory tests were conducted with four non-steroidal anti-inflammatory drugs (naproxen, ibuprofen, diclofenac and ketoprofen) under different redox conditions (aerobic, anoxic, anaerobic and sulfate-reducing conditions) in order to assess abiotic and biotic degradation in a river water/sediment system. The river water was sampled from Sperchios River and the sediment was collected from the banks of a rural stream where the discharge point of a wastewater treatment plant is located. To quantitatively describe degradation kinetics of the selected compounds, pseudo first-order kinetics were adopted. According to the results, it can be stated that the concentration of the substances remained constant or decreased only marginally (p≥0.05) in the sterile experiments and this excludes abiotic processes such as hydrolysis or sorption as major removal mechanisms of the target compounds from the water phase and assign their removal to microbial action. Results showed that the removal rate of the compounds decreases as dissolved oxygen concentration in the river water/sediment system decreases. All compounds were found to be biodegradable under aerobic conditions at dissipation half-lives between 1.6 and 20.1days, while dissipation half-lives for naproxen and ketoprofen increase by a factor of 2 under all tested conditions in the absence of oxygen.

Detection and quantification of acidic drug residues in South African surface water using gas chromatography-mass spectrometry

A method was optimized for derivatization, separation, detection and quantification of salicylic acid, acetylsalicylic acid, nalidixic acid, ibuprofen, phenacetin, naproxen, ketoprofen, meclofenamic acid and diclofenac in surface water using gas chromatography-mass spectrometry. For most of the acidic drugs, recovery was in the range 60-110% and the percent standard deviation was below 15% for the entire method, with limits of detection ranging from 0.041 to 1.614 μg L^-1. The developed method was applied in the analysis of acidic drugs in Umgeni River system, KwaZulu-Natal South Africa. All of the selected acidic drugs were detected and quantified, their concentration in Umgeni River system ranged from 0.0200 to 68.14 μg L^-1.

Procedures of determining organic trace compounds in municipal sewage sludge-a review

Sewage sludge is the largest by-product generated during the wastewater treatment process. Since large amounts of sludge are being produced, different ways of disposal have been introduced. One tempting option is to use it as fertilizer in agricultural fields due to its high contents of inorganic nutrients. This, however, can be limited by the amount of trace contaminants in the sewage sludge, containing a variety of microbiological pollutants and pathogens but also inorganic and organic contaminants. The bioavailability and the effects of trace contaminants on the microorganisms of soil are still largely unknown as well as their mixture effects. Therefore, there is a need to analyze the sludge to test its suitability before further use. In this article, a variety of sampling, pretreatment, extraction, and analysis methods have been reviewed. Additionally, different organic trace compounds often found in the sewage sludge and their methods of analysis have been compiled. In addition to traditional Soxhlet extraction, the most common extraction methods of organic contaminants in sludge include ultrasonic extraction (USE), supercritical fluid extraction (SFE), microwave-assisted extraction (MAE), and pressurized liquid extraction (PLE) followed by instrumental analysis based on gas or liquid chromatography and mass spectrometry.

Bar adsorptive microextraction technique - application for the determination of pharmaceuticals in real matrices

In the present work, bar adsorptive microextraction using miniaturized devices (7.5 × 3.0 mm) coated with suitable sorbent phases, combined with microliquid desorption (100 μL) followed by high-performance liquid chromatography with diode array detection (BAμE-μLD/HPLC-DAD), is proposed for the determination of trace level of six pharmaceuticals (furosemide, mebeverine, ketoprofen, naproxen, diclofenac and mefenamic acid) in environmental water and urine matrices. By comparing ten distinct sorbent materials (five polymeric and five activated carbons), the polymer P5 proved to be the most suitable to achieve the best selectivity and efficiency. The solvent volume minimization in the liquid desorption stage demonstrated remarkable effectiveness, being more environmentally friendly, and simultaneously increased the microextraction enrichment factor two-fold. Assays performed through BAμE(P5, 0.9 mg)-μLD(100 μL)/HPLC-DAD on 25 mL of ultrapure water samples spiked at the 4.0 μg/L level yielded average recoveries ranging from 91.4% (furosemide) to 101.0% (ketoprofen) with good precision (RSD < 10.6%), under optimized experimental conditions. The analytical performance showed convenient detection limits (25.0 - 120.0 ng/L), good linear dynamic ranges (0.1 to 24.0 μg/L), appropriate determination coefficients (r ² > 0.9983), and excellent repeatability through intraday (RSD < 10.4%)) and interday (RSD < 10.0%) assays. By using the standard addition methodology, the application of the present analytical approach on environmental waters and urine samples revealed the occurrence of trace levels of some pharmaceuticals. The solvent minimization during the back-extraction step associated with the miniaturization of BAμE devices proved to be a very promising analytical technology for static microextraction analysis. Graphical abstract BAμE operating under the floating sampling technology for the determination of pharmaceuticals in aqueous media.

Differential BPA levels in sewage wastewater effluents from metro Detroit communities

The endocrine disruptor Bisphenol A (BPA) is ubiquitous in both aquatic and surface sediment environments because it is continuously released into sewage wastewater effluent. The measurement of BPA at wastewater treatment plants is rarely performed even though the United States Environmental Protection Agency (EPA) states that current levels of environmental BPA could be a threat to aquatic organisms. Therefore, the aims of this study were to measure BPA levels in sewage wastewater at different collection points over a 1-year period and to compare the levels of BPA to 8-isoprostane, a human derived fatty acid, found in sewage wastewater. We analyzed pre-treated sewage samples collected from three source points located in different communities in the metropolitan Detroit area provided by the Detroit Water and Sewerage Department. Human urine samples were also used in the study. BPA and 8-isoprostane were measured using ELISA kits from Detroit R&D, Inc. BPA levels from the same collection point oscillated more than 10-fold over 1 year. Also, BPA levels fluctuated differentially at each collection point. Highly fluctuating BPA values were confirmed by LC/MS/MS. The concentration of BPA in sewage wastewater was ~100-fold higher than the concentration of 8-isoprostane, while urinary concentration was ~20-fold higher. Thus, BPA levels discharged into the sewage network vary among communities, and differences are also observed within communities over time. The difference in BPA and 8-isoprostane levels suggest that most of the BPA discharged to sewage wastewater might be derived from industries rather than from human urine. Therefore, the continuous monitoring of BPA could account for a better regulation of BPA release into a sewage network.

Fractionation of trace elements in agricultural soils using ultrasound assisted sequential extraction prior to inductively coupled plasma mass spectrometric determination

The main objectives of this study were to determine the concentration of fourteen trace elements and to investigate their distribution as well as a contamination levels in selected agricultural soils. An ultrasonic assisted sequential extraction procedure derived from three-step BCR method was used for fractionation of trace elements. The total concentration of trace elements in soil samples was obtained by total digestion method in soil samples with aqua regia. The results of the extractable fractions revealed that most of the target trace elements can be transferred to the human being through the food chain, thus leading to serious human health. Enrichment factor (EF), geo-accumulation index (Igeo), contamination factor (CF), risk assessment code (RAC) and individual contamination factors (ICF) were used to assess the environmental impacts of trace metals in soil samples. The EF revealed that Cd was enriched by 3.1-7.2 (except in Soil 1). The Igeo results showed that the soils in the study area was moderately contaminated with Fe, and heavily to extremely polluted with Cd. The soil samples from the unplanted field was found to have highest contamination factor for Cd and lowest for Pb. Soil 3 showed a high risk for Tl and Cd with RAC values of greater than or equal to 50%. In addition, Fe, Ni, Cu, V, As, Mo (except Soil 2), Sb and Pb posed low environmental risk. The modified BCR sequential extraction method provided more information about mobility and environmental implication of studied trace elements in the study area.

Degradation of emerging contaminants from water under natural sunlight: The effect of season, pH, humic acids and nitrate and identification of photodegradation by-products

Both photodegradation and hydrolysis of non-steroidal anti-inflammatory drugs (NSAIDs) and endocrine disrupting chemicals (EDCs) were investigated in order to evaluate their photochemical fate in aquatic environment and to assess the effect of season and specific characteristics of water (pH, humic acids and nitrate concentration) on the removal of target EDCs and NSAIDs through photodegradation. An additional objective was the identification of the photodegradation by-products of specific NSAIDs and their dependence on irradiation time. Selected compounds' transformation was investigated under natural sunlight radiation while control experiments were conducted in the dark. As expected, most of compounds' degradation rate decreased with decreasing light intensity between two different experimental periods. Most of the tested compounds exhibited different rates of degradation during direct and indirect photolysis. The degradation rate of the selected compounds increased in the presence of NO3(-) and the photodegradation rate was higher for some compounds in alkaline than in acidic solution. The effect of humic acids' presence in the water depends on the absorbance spectrum of the compound and the produced photosensitizers. More specifically, humic acids act as inner filter toward most of the selected NSAIDs and as photosensitizers toward most of the EDCs. The results of the irradiation experiments in the presence of both humic acids and NO3(-), indicate that the direct photolysis is much more efficient than indirect photochemical processes. Finally, several degradation by-products of ketoprofen and diclofenac were identified in the samples, exposed to sunlight. The dependence of these by-products on radiation time is also demonstrated.

An immunoassay for the detection of triclosan-O-glucuronide, a primary human urinary metabolite of triclosan

Triclosan-O-glucuronide (TCSG) is one of the primary urinary metabolites of the antibacterial compound triclosan or TCS that is found in many personal care products and consumer goods. We have developed a competitive, indirect heterologous ELISA for the detection of the target TCSG in urine. Such an ELISA for TCSG could be developed as a useful tool to measure this important biomarker of human exposure to TCS. Immunogens were prepared by conjugating TCSG to thyroglobulin, via heterobifunctional cross-linkers AEDP or 3-[(2-aminoethyl)dithio] propionic acid•hydrochloride and TFCS or N-[ε-trifluoroacetylcaproyloxy]succinimide ester. The coating antigen was prepared by the direct conjugation of TCSG to bovine serum albumin. Antibodies raised in rabbits 2619, 2621 (immunogen TCSG-AEDP-Thy), and 2623 (immunogen TCSG-TFCS-Thy), and the coating antigen were screened and characterized to determine their optimal concentrations. The optimized ELISA, developed with antibody 2621, gave an IC50 value of 2.85 ng/mL, with the linear range (IC20-IC80) determined to be 2.6-24.8 ng/mL. Selectivity of the assay was assessed by measuring cross-reactivity of antibody 2621 to related congeners such as the aglycone TCS, triclosan-O-sulfate, triclocarban, a polybrominated diphenyl ether derivative, and 3-phenoxybenzyl alcohol glucuronide. There was virtually no recognition by antibody 2621 to any of these cross-reactants. Graphical Abstract Urinary biomarker analysis of triclosan glucuronide.

GC/MS analysis of triclosan and its degradation by-products in wastewater and sludge samples from different treatments

A gas chromatography/mass spectrometry (GC/MS)-based method was developed for simultaneous determination of triclosan (TCS) and its degradation products including 2,4-dichlorophenol (2,4-DCP), 2,8-dichlorodibenzo-p-dioxin (2,8-DCDD), and methyl triclosan (MTCS) in wastewater and sludge samples. The method provides satisfactory detection limit, accuracy, precision and recovery especially for samples with complicated matrix such as sewage sludge. Liquid-liquid extraction and accelerated solvent extraction (ASE) methods were applied for the extraction, and column chromatography was employed for the sample cleanup. Analysis was performed by GC/MS in the selected ion monitoring (SIM) mode. The method was successfully applied to wastewater and sludge samples from three different municipal wastewater treatment plants (WWTPs). Satisfactory mean recoveries were obtained as 91(±4)-106(±7)%, 82(±3)-87(±4)%, 86(±6)-87(±8)%, and 88(±4)-105(±3)% in wastewater and 88(±5)-96(±8)%, 84(±2)-87(±3)%, 84(±7)-89(±4)%, and 88(±3)-97(±5)% in sludge samples for TCS, 2,4-DCP, 2,8-DCDD, and MTCS, respectively. TCS degradation products were detected based on the type of the wastewater and sludge treatment. 2,8-DCDD was detected in the plant utilizing UV disinfection at the mean level of 20.3(±4.8) ng/L. 2,4-DCP was identified in chemically enhanced primary treatment (CEPT) applying chlorine disinfection at the mean level of 16.8(±4.5) ng/L). Besides, methyl triclosan (MTCS) was detected in the wastewater collected after biological treatment (10.7 ± 3.3 ng/L) as well as in sludge samples that have undergone aerobic digestion at the mean level of 129.3(±17.2) ng/g dry weight (dw).

Effects of triclosan, diclofenac, and nonylphenol on mesophilic and thermophilic methanogenic activity and on the methanogenic communities

In this study, a toxicity assay using a mesophilic wastewater treatment plant sludge-based (SI) and a thermophilic manure-based inoculum (MI), under different biomass concentrations was performed to define the effects of diclofenac (DCF), triclosan (TCS), and nonylphenol (NP) on anaerobic digestion (AD) process. Additionally, the influence of DCF, TCS, and NP on the relative abundance of the methanogenic populations was investigated. Results obtained demonstrated that, in terms of methane production, SI inoculum was more resistant to the toxicity effect of DCF, TCS, and NP, compared to the MI inoculum. The IC50 values were 546, 35, and 363 mg L(-1) for SI inoculum and 481, 32, and 74 mg L(-1) for MI inoculum for DCF, TCS, and NP, respectively. For both inocula, higher biomass concentrations reduced the toxic effect of TCS (higher methane production up to 64%), contrary to DCF, where higher biomass loads decreased methane yield up to 31%. Fluorescence in situ hybridization analysis showed that hydrogenotrophic methanogens were more resistant to the inhibitory effect of DCF, TCS, and NP compared to aceticlastic methanogens.

Removal of endocrine disruptors and non-steroidal anti-inflammatory drugs through wastewater chlorination: the effect of pH, total suspended solids and humic acids and identification of degradation by-products

Endocrine disrupting chemicals (EDCs) and non-steroidal anti-inflammatory drugs (NSAIDs) are two groups of emerging pollutants the significance of which rests on their persistent detection in the aquatic environment and their possible adverse effects. Wastewater treatment plants are one of the major ways for transporting such chemicals in the aquatic environment. Chlorination is usually the last stage of treatment before wastewater being disposed to the aquatic environment. This work focuses on the evaluation of the effect of chlorine dose and specific wastewater characteristics (pH, total suspended solids and humic acids) on the removal of target EDCs and NSAIDs through chlorination. Another objective of this study is the identification of chlorination by-products of specific EDCs and NSAIDs and their dependence on contact time. Based on the results it is concluded that the effect of chlorine dose and humic acids concentration on the degradation of target compounds during chlorination is minimal. On the contrary, pH is a critical parameter which highly affects process performance. Moreover, it is concluded that not only the free available chlorine species, but also the properties of EDCs and NSAIDs under different pH conditions can affect chlorination process performance. The effect of TSS on the degradation of the target compounds during chlorination is more profound for chemicals with high Kow values and therefore higher affinity to partition to the particulate phase (i.e. nonylphenols, triclosan). Several degradation by-products were identified through chlorination of nonylphenol, bisphenol A and diclofenac. The dependence of these by-products on chlorination contact time is also demonstrated.

Screening of hormone-like activities in bottled waters available in Southern Spain using receptor-specific bioassays

Bottled water consumption is a putative source of human exposure to endocrine-disrupting chemicals (EDCs). Research has been conducted on the presence of chemicals with estrogen-like activity in bottled waters and on their estrogenicity, but few data are available on the presence of hormonal activities associated with other nuclear receptors (NRs). The aim of this study was to determine the presence of endocrine activities dependent on the activation of human estrogen receptor alpha (hERa) and/or androgen receptor (hAR) in water in glass or plastic bottles sold to consumers in Southern Spain. Hormone-like activities were evaluated in 29 bottled waters using receptor-specific bioassays based on reporter gene expression in PALM cells [(anti-)androgenicity] and cell proliferation assessment in MCF-7 cells [(anti-)estrogenicity] after optimized solid phase extraction (SPE). All of the water samples analyzed showed hormonal activity. This was estrogenic in 79.3% and anti-estrogenic in 37.9% of samples and was androgenic in 27.5% and anti-androgenic in 41.3%, with mean concentrations per liter of 0.113pM 17β-estradiol (E2) equivalent units (E2Eq), 11.01pM anti-estrogen (ICI 182780) equivalent units (ICI 182780Eq), 0.33pM methyltrienolone (R1881) equivalent units (R1881Eq), and 0.18nM procymidone equivalent units (ProcEq). Bottled water consumption contributes to EDC exposure. Hormone-like activities observed in waters from both plastic and glass bottles suggest that plastic packaging is not the sole source of contamination and that the source of the water and bottling process may play a role, among other factors. Further research is warranted on the cumulative effects of long-term exposure to low doses of EDCs.

Is there a risk for the aquatic environment due to the existence of emerging organic contaminants in treated domestic wastewater? Greece as a case-study

The ecological threat associated with emerging pollutants detected in wastewater was estimated in country level. Treated wastewater was analyzed for pharmaceuticals and illicit drugs; whereas the concentrations of all emerging contaminants determined in Greek Sewage Treatment Plants were recorded through literature review. Toxicity data was collected after literature review or using ECOSAR and risk quotients (RQs) were calculated for treated wastewater and 25 Greek rivers, for 3 different aquatic organisms (fish, daphnia magna, algae). According to the results, monitoring data was available for 207 micropollutants belonging to 8 different classes. RQ>1 was calculated for 30 compounds in secondary treated wastewater. Triclosan presented RQ>1 (in algae) for all studied rivers; decamethylcyclopentasilane (in daphnia magna), caffeine (in algae) and nonylphenol (in fish) presented RQ>1 in rivers with dilution factors (DF) equal or lower to 1910, 913 and 824, respectively. The class of emerging contaminants that present the greatest threat due to single or mixture toxicity was endocrine disrupters. The mixture of microcontaminants seems to pose significant ecological risk, even in rivers with DF equal to 2388. Future national monitoring programs should include specific microcontaminants that seem to possess environment risk to surface water.