Cetyltrimethylammonium bromide-treated Phragmites australis powder as novel polymeric adsorbent for hazardous Eriochrome Black T removal from aqueous solutions

Powdered silk: A promising biopolymer for the treatment of dye contaminated water

Discharge of textile dye effluents into water bodies is creating stress to aquatic life and contaminating water resources. In this study, a new biopolymer adsorbent silk fibroin (SF) was prepared from Bombyx mori silk fibroin (SF) and used for removal of Solochrome Black-T (SB-T) from water. This innovative adsorbent exhibits an exceptional adsorption capacity of 20.08 mg/g, achieving a removal efficiency of approximately 98.6 % within 60 min. Notably, the powdered SF adsorbent demonstrates rapid kinetics, surpassing the performance of previously reported similar adsorbents in adsorption capacity and reaction speed. The molecular weight and particle diameter of the material were observed to be > 1.243 kDa and 3 μm, respectively. The experimental investigations were performed on different parameters, viz., adsorbent dosage, contact time, repeatability, and desorption-adsorption study. The experimental data well fit for the Langmuir model (R2 = 0.937, qmax = 20.08 mg/g) and the pseudo-second-order kinetics (R2 = 0.921 and qe = 1.496 mg/g). Compared to the adsorbents reported in the literature, the newly prepared SF showed high adsorption capacity and faster kinetics to address real-life situations. The novelty of this work extends beyond its remarkable adsorption capabilities. The SF adsorbent offers a cost-effective, sustainable solution and regenerable adsorption material with minimal negative environmental impacts. This regenerability, with its versatility and broad applicability, positions powdered SF fibroin as a transformative technology in water treatment and environmental protection.

Cellulose nanofibers decorated with SiO2 nanoparticles: Green adsorbents for removal of cationic and anionic dyes; kinetics, isotherms, and thermodynamic studies

Cellulose nanofibers decorated with SiO2 nanoparticles (SiO2-CNF) were prepared by the extraction of cellulose nanofibers from Yucca leaves, followed by modification with SiO2 nanoparticles, and used as efficient materials for the removal of both anionic and cationic dyes from the aqueous solution. Prepared nanostructures were characterized using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction powder (XRD), Thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), and transmission electron microscopy (TEM) analysis. The adsorption capacity of the nanostructures was investigated for the removal of both cationic (Methylene Blue, MB, and Crystal Violet, CV) and anionic (Eriochrome Black-T, EB) dyes. The kinetics of adsorption were investigated using some well-known models, including intraparticular diffusion (IPD), pseudo-first-order (PFO), pseudo-second-order (PSO), and Elovich. The adsorption isotherms were also explored using the Langmuir, Freundlich, Temkin, and Redlich-Peterson models. The obtained results revealed that the adsorption processes follow PSO kinetic and Langmuir isotherm models. Thermodynamic parameters of the adsorption were measured at different temperatures, indicating the feasibility and spontaneity of the adsorption. The pH and salt effects on adsorption were also explored. Finally, according to the reusability tests, the prepared adsorbents showed high recoverability without considerable loss in adsorption efficiency after five repeated runs.

Green solid-liquid extraction of cactus (Opuntia ficus-indica) cladode dietary fibers. I- optimization, pilot-scale production, and characterization

In this research work, an optimization of an environment friendly extraction method of cactus (Opuntia ficus indica) cladode dietary fibers was conducted. For this purpose, a central composite experimental design with two factors (temperature and time) and five levels was established. The basic objective of this optimization was to maximize fiber yield using hot water as an extraction eco-solvent. The optimum extraction time (330 min) and temperature (100 °C) were determined with a constant medium agitation rate. Additionally, this study also aimed at establishing the validation of the statistical model to carry out the extrapolation of the extraction process at the pilot scale. The fibers extracted at the pilot scale showed yields (45.2 ± 0.01%) in agreement with those obtained through the optimization and validation lab-scale steps (44.97 ± 0.02). Fourier Transform Infrared (FTIR) spectroscopy, X-ray Diffraction (XRD) and Scanning electron microscopy (SEM) analysis were conducted to investigate the structure and microstructure of pilot scale-produced fibers. FTIR spectrum and XRD pattern were typical to lignocellulosic fibers results. Sharp and thin peaks characteristic of cellulose were detected. Pure and crystallized phases were recorded with a 45% crystallinity index. SEM analysis presented elongated and organized cells with a uniform structure comparable to cellulosic fibers microstructure.

Construction of an egg-like DTAB/SiO2 composite for the enhanced removal of uranium

For the past few years, the environmental safety problems of radioactive nuclides caused wide public concern. In this work, the dodecyl trimethyl ammonium bromide-modified silicon dioxide composite (DTAB/SiO₂) was synthesized for the elimination of uranium. The dodecyl trimethyl ammonium bromide can decorate the surface of the silicon dioxide and change its surface topography, which can offer more active sites and functional groups for the combination of U(VI). The removal capacity of U(VI) on DTAB/SiO₂ reached 78.1 mg/g, which was greater than that of the silicon dioxide nanopowder. In the adsorption process, the surface oxygen-containing functional groups formed surface complexation with uranium. The results may provide helpful content to eliminate U(VI) and expand the application of surfactant in radioactive nuclide cleanup.

Optimization of synergistic biosorption of oxytetracycline and cadmium from binary mixtures on reed-based beads: modeling study using Brouers-Sotolongo models

The first aim of this study was to synthesize and characterize reed-based-beads (BBR), an enhanced adsorbent from Tunisian reed. The second purpose was to evaluate and optimize the BBR efficiency for the simultaneous removal of oxytetracycline (OTC) and cadmium (Cd(II)), using central composite design under response surface methodology. The third goal was to elucidate the biosorption mechanisms taking place. It was shown that under optimum conditions (4.19 g L^-1 of BBR, 165.54 μmol L^-1 of OTC, 362.16 μmol L^-1 of Cd(II), pH of 6, and 25.14-h contact time) the highest adsorption percentages (63.66% for OTC and 99.99% for Cd(II)) were obtained. It was revealed that OTC adsorption mechanism was better described by Brouers-Sotolongo fractal equation, with regression coefficient (R²) of 0.99876, and a Person's chi-square (χ²) of 0.01132. The Weibull kinetic equation better explained Cd(II) biosorption (R² = 0.99959 and χ² = 0.00194). FTIR and isotherm studies confirmed that the BBR surface was heterogeneous, and that adsorption mechanisms were better described by the Freundlich/Jovanovich equation (R² = 0.99276 and χ² = 0.04864) for OTC adsorption, and by the Brouers-Sotolongo model (R² = 0.9851 and χ² = 0.77547) for Cd(II) biosorption. Overall results indicate that, at last, the BBR lignocellulosic biocomposite beads could be considered as cost-effective and efficient adsorbent, which could be of socioeconomic and environmental relevance. Graphical abstract.

Development of novel and ecological keratin/cellulose-based composites for absorption of oils and organic solvents

Keratin/cellulose cryogels were successfully fabricated using chicken feathers (CF) and cardboard (C) from environmental waste for the first time, to be exploited in oil/solvent absorption. The keratin/cellulose-based composites were obtained by combining the dissolution of CF and C waste in 1-butyl-3-methylimidazolium chloride (Bmim^-Cl⁺) ionic liquid green solvent via regeneration, simply by the freeze-drying method. The characterization analysis of the synthesized keratin/cellulose-based composites was performed using Fourier transform infrared spectrometry, X-ray diffractometry, scanning electron microscopy, and thermogravimetry. The as-prepared cryogel can absorb various oils and organic solvents. Moreover, its sorption capacity can reach up to 6.9-17.7 times the weight of the initial cryogel. This kind of CF/C cryogel revealed good and fast absorption efficiency. It could also be reused by simple absorption/distillation and absorption/desorption methods. Through the kinetic analysis, it was found that the pseudo-second-order model was more appropriate for the keratin/cellulose cryogel oil absorption process. Besides, owing to its low cost, good absorption capacity, and excellent reusability, this cryogel has potential for spill cleanup of oils and organic solvents.

Enhanced Cu(II) adsorption using sodium trimetaphosphate-modified cellulose beads: equilibrium, kinetics, adsorption mechanisms, and reusability

The current study is focused on the simple synthesis of two novel biosorbent beads: BASB/STMP and CNFB/STMP, derived respectively from bleached almond shell (BAS) and cellulose nanofiber from almond shell (CNF) by means of chemical crosslinking with sodium trimetaphosphate (STMP). These biosorbents were thoroughly characterized in terms of structure (FTIR), texture (N₂ adsorption-desorption), thermal behavior (TGA/DTG), morphology (SEM), and surface properties (XPS). The adsorption kinetics of Cu(II) ions onto BASB/STMP and CNFB/STMP materials proved the chemisorption interaction between Cu(II) ions and the STMP functionalized beads. The BASB/STMP equilibrium data were successfully described by the Redlich-Peterson model and the CNFB/STMP data by the Sips model which disclosed maximum adsorption capacities of 141.44 mg g^-1 and 147.90 mg g^-1, respectively. Furthermore, the BASB/STMP bioadsorbent offers easy regeneration and better reusability with high efficiency (> 83%). This study sheds light on the preparation of low-cost adsorbents for wastewater treatment in order to improve the competitiveness and eco-friendliness of agrowaste-based processes.

Adsorption Characteristics of Polymer Solutions on Media Surfaces and Their Main Influencing Factors

In practical applications, the chemical and physical adsorption of a polymer solution greatly affects its action mode and effect. Understanding the adsorption mechanism and its influencing factors can help to optimize the application mode and ensure application efficiency. Three types of polymer solutions-partially hydrolyzed polyacrylamide (HPAM), hydrophobically associating polymer (AP-P4), and dendrimer hydrophobically associating polymer (DHAP), which are viscoelastic liquids-were used as sorbates to study their adsorption by a sorbent such as quartz sand. The effects of the solution concentration, contact time, particle size of quartz sand, solid-liquid ratio, and fluid movement on the adsorption capacity of the polymer solutions were examined. The results showed that HPAM presents a typical Langmuir monolayer adsorption characteristic, and its adsorption capacity (per unit area) is 1.17-1.62 μg/cm2. The association enhances the interactions of the AP-P4 and DHAP solutions, and they present multilayer characteristics of first-order chemical adsorption and secondary physical molecule adsorption. Moreover, the dendrite structure further increases the adsorption thickness of DHAP. Hence, the adsorption thicknesses of AP-P4 and DHAP are four and six times that of HPAM, respectively. The adsorption of the three polymers is consistent with the influence of fluid motion and decreases with increasing fluid velocity. However, the larger the thickness of the adsorption layer, the clearer the influence of the flow, and the higher the decrease in adsorption capacity. Optimizing the injection rate is an effective method to control the applications of a polymer in porous media.