Wound morphology in contact shots from blank cartridge handguns: a study on composite models

Assessment of injuries patterns produced by a 9mm P.A.K "rubber ball" blank firing weapon: porcine model

The use of less lethal weapons aims to mitigate civilian casualties caused by firearm use. However, due to numerous cases in which these weapons caused serious injuries, even lethal injuries, both legislation and the forensic field are interested in characterizing and regulating them better. In the forensic field, there is a lack of strong research about injury patterns of these weapons which makes it difficult to identify the type of weapon employed. In this study, the main objective was to characterize the injury pattern produced by the impact of the 9 mm P.A.K. projectile. A porcine model was used. Four different distances were studied: firm contact, 10 cm, 60 cm and 110 cm, using 3 of the more representative anatomical sites: the head, the hind leg and the ribs. The average measurement of the entrance orifice varied according to the anatomical site, being 6.67 mm wide and 6.25 mm long in the thorax, 7.3 mm wide and 8.8 mm long in the hind legs, and 7.62 mm wide and 7.54 mm long in the head. The variation in width and length measurements was not found to be directly related to the shot distance. The gunshot residues had similar characteristics to those of conventional lead projectiles, however there was more unburned powder deposit near the wounds, with a less dense soot and more dense powder tattoo. Depth varied widely regardless of tissue and firing distance, although loss of penetrating power and injury is observed as one moves away from the target.

Skin simulants for wound ballistic investigation - an experimental study

Gunshot wound analysis is an important part of medicolegal practice, in both autopsies and examinations of living persons. Well-established and studied simulants exist that exhibit both physical and biomechanical properties of soft-tissues and bones. Current research literature on ballistic wounds focuses on the biomechanical properties of skin simulants. In our extensive experimental study, we tested numerous synthetic and natural materials, regarding their macromorphological bullet impact characteristics, and compared these data with those from real bullet injuries gathered from medicolegal practice. Over thirty varieties of potential skin simulants were shot perpendicularly, and at 45°, at a distance of 10 m and 0.3 m, using full metal jacket (FMJ) projectiles (9 × 19 mm Luger). Simulants included ballistic gelatine at various concentrations, dental silicones with several degrees of hardness, alginates, latex, chamois leather, suture trainers for medical training purposes and various material compound models. In addition to complying to the general requirements for a synthetic simulant, results obtained from dental silicones shore hardness 70 (backed with 20 % by mass gelatine), were especially highly comparable to gunshot entry wounds in skin from real cases. Based on these results, particularly focusing on the macroscopically detectable criteria, we can strongly recommend dental silicone shore hardness 70 as a skin simulant for wound ballistics examinations.

Survival of a Blank Cartridge Gunshot Injury to the Soft Palate in a Soldier

ABSTRACT

The authors report a case of a soldier who survived after shooting a blank round from a K2 rifle into the oral cavity.For committing suicide, a 22-year-old male soldier shot a K2 rifle into his oral cavity. Because the first shot was a blank fire, he received an injury to his oral cavity, especially to his palate. On arrival hospital via air evacuation, the patient's vital signs were relatively stable and Glasgow Coma Scale score was 15. Profound epistaxis was noted from both nostrils, and his mouth was filled with blood. Intubation was performed immediately, followed by tracheostomy. On computed tomography scan, the palate was injured and laryngeal edema was seen.On operative field, severe swelling of the larynx was observed. Gunpowder remained present throughout nearly the entire palate. His palate was burned, and there was a 3-cm-diameter mucosal defect. The bleeding point was cauterized, and bleeding was controlled using oral packing. The packing was changed every morning for the first 2 days, and finally removed on the third day of hospitalization. On the eighth day of hospitalization, the defect of his soft palate showed healing by secondary intention, and a planned reconstructive operation was not needed. Tracheostomy was removed on the 45th day. He was able to eat and speak at the time of discharge (93rd day).The authors cannot overemphasize the importance of the airway in oral injuries. Packing for bleeding control under a safe airway should be followed as a routine part of the protocol for similar cases.

Nothing but hot air?-On the molecular ballistic analysis of backspatter generated by and the hazard potential of blank guns

Blank cartridge guns are prevalent especially in countries with laws restricting access to conventional firearms, and it is a common misconception that these weapons are harmless and only used as toys or for intimidation. However, although their harming potential is well-documented by numerous reports of accidents, suicides, and homicides, a systematic molecular biological investigation of traces generated by shots from blank cartridges at biological targets has not been done so far. Herein, we investigate the occurrence and analyzability of backspatter generated by shots of different types of blank cartridge guns firing different types of blank ammunition at ballistic gelatin model cubes doped with human blood and radiological contrast agent soaked into a spongious matrix and covered with three different variants of skin simulants. All skin simulants were penetrated, and backspatter was created in 100% of the shots in amounts sufficient for forensic short tandem repeat (STR) typing that resulted in the correct identification of the respective blood donor. Visible backspatter was documented on the muzzle and/or inside the barrel in all cases, and in 75% of cases also on the outer surfaces and on the shooter’s hand(s). Wound cavities were measured and ranged between 1 and 4.5 cm in depth. Discussing our findings, we provide recommendations for finding, recovering, and analyzing trace material from blank guns, and we demonstrate the considerable hazard potential of these devices, which is further emphasized by the presentation of a comprehensive overview of the pertinent literature on injuries inflicted by blank guns.

Interpol review of forensic firearm examination 2016-2019

This review paper covers the relevant literature on forensic firearm examination from 2016 to 2019 as a part of the 19th Interpol International Forensic Science Managers Symposium. The review papers are also available at the Interpol website at: https://www.interpol.int/content/download/14458/file/Interpol%20Review%20Papers%202019.pdf.

Rearward movement of the slide in semi-automatic pistols: a factor potentially influencing the configuration of muzzle imprint marks in contact shots

A muzzle imprint mark is a highly diagnostic finding, which indicates a contact shot. In many cases, it also provides additional information on the type of the weapon used and on the way in which it was held at the time of firing. In semi-automatic pistols, some constructional elements constituting the muzzle plane move to the rear together with the slide, which may prevent them from causing a corresponding imprint close to the bullet entrance hole. The present study comprises 30 consecutive autopsy cases of fatal contact shots to the head inflicted with semi-automatic pistols. The imprint marks accompanying the entrance wounds were compared with the muzzle ends of the respective weapons both before and after retracting the slide. It turned out that in a considerable number of cases (3 out of 30), the retractable parts were not depicted or only to a minor degree as components of the imprint mark. In order to validate the presumed correlation, experimental shots were fired to composite models using pistols in which the movable and the stationary parts forming the muzzle plane were dyed with different paints. Thus, it could be demonstrated that the muzzle imprint preferentially mirrors the front sides of the stationary parts such as the barrel end, the recoil guide, and the gun housing. Immediately after discharge, the slide and the ballooning skin of the bullet entrance site move in the same direction. The stationary parts of the weapon block the expansion of the skin bulging towards the muzzle, so that the skin gets firmly pressed against them. The dynamic interaction between the gun and the entrance region resulting in a characteristic imprint mark could be visualized by the use of a high-speed motion camera recording test shots to different composite models.