Turn-on fluorometric immunosensor for diethylstilbestrol based on the use of air-stable polydopamine-functionalized black phosphorus and upconversion nanoparticles

Development of a monoclonal antibody-based indirect competitive enzyme-linked immunosorbent assay for screening of diethylstilbestrol in animal-derived foods

Diethylstilbestrol (DES), a synthetic non-steroid estrogen, it has been prohibited from being added to animal feed for any purposes. Herein, an indirect competitive enzyme-linked immunosorbent assay (ic-ELISA) based on a specific monoclonal antibody (mAb) was developed for the rapid screening of DES. Primarily, conjugates of mono-O-3-carboxypropyl diethylstilbestrol with keyhole limpet hemocyanin were used to raise a specific mAb, 1B7, which had IC50 value for DES of 213.0 ng L-1. The limits of detection and limits of quantification value for DES in animal-derived foods ranged from 68.1 to 103.1 ng L-1 and 100.8-192.7 ng L-1, respectively. The DES recovery ranged from 70.1 % to 103.1 %, with coefficients of variation below 13.9 %. A positive correlation (R2 = 0.997) was observed between the results of ic-ELISA and HPLC-MS/MS for milk. In order to inspect its detection effect, milk and animal-derived foods were chosen as the testing object. The results showed that this ic-ELISA method (specific mAb, 1B7) can effectively examine for DES residues.

Functional black phosphorus-based sensors for food safety applications: A review

Food safety has garnered global attention, necessitating advanced methods for the quick and accurate detection of contaminants. Sensors, notable for their ease of use, high sensitivity, and fast analysis, are prominent. Two-dimensional (2D) nanomaterials have been employed to improve sensor performance. Particularly, black phosphorus (BP) stands out with its multifunctional capabilities, attributed to unique layered structure, ultra-high charge mobility, easy surface functionalization, enhanced optical absorption, and tunable direct bandgap. These characteristics suggest that BP could significantly enhance sensor selectivity, sensitivity, and response speed for contaminant detection. Despite numerous studies on BP-based sensors in food safety, few reviews have been comprehensively summarized. Moreover, challenges in BP's preparation and stability restrict its wider use. This paper reviews recent research on BP's role in food safety, covering preparation, passivation, and applications. Through analysis of challenges and prospects, this review aims to provide insightful guidance for upcoming research in this area.

PDA-BPs integrated mussel-inspired multifunctional hydrogel coating on PPENK implants for anti-tumor therapy, antibacterial infection and bone regeneration

Currently, many cancer patients with bone defects are still threatened by tumor recurrence, postoperative bacterial infection, and massive bone loss. Many methods have been studied to endow bone implants with biocompatibility, but it is difficult to find an implant material that can simultaneously solve the problems of anticancer, antibacterial and bone promotion. Here, a multifunctional gelatin methacrylate/dopamine methacrylate adhesive hydrogel coating containing 2D black phosphorus (BP) nanoparticle protected by polydopamine (pBP) is prepared by photocrosslinking to modify the surface of poly (aryl ether nitrile ketone) containing phthalazinone (PPENK) implant. The multifunctional hydrogel coating works in conjunction with pBP, which can deliver drug through photothermal mediation and kill bacteria through photodynamic therapy at the initial phase followed by promotion of osteointegration. In this design, photothermal effect of pBP control the release of doxorubicin hydrochloride loaded via electrostatic attraction. Meanwhile, pBP can generate reactive oxygen species (ROS) to eliminate bacterial infection under 808 nm laser. In the slow degradation process, pBP not only effectively consumes excess ROS and avoid apoptosis induced by ROS in normal cells, but also degrade into PO₄^3- to promote osteogenesis. In summary, nanocomposite hydrogel coatings provide a promising strategy for treatment of cancer patients with bone defects.

Recent Progress on Techniques in the Detection of Aflatoxin B1 in Edible Oil: A Mini Review

Contamination of agricultural products and foods by aflatoxin B1 (AFB1) is becoming a serious global problem, and the presence of AFB1 in edible oil is frequent and has become inevitable, especially in underdeveloped countries and regions. As AFB1 results from a possible degradation of aflatoxins and the interaction of the resulting toxic compound with food components, it could cause chronic disease or severe cancers, increasing morbidity and mortality. Therefore, rapid and reliable detection methods are essential for checking AFB1 occurrence in foodstuffs to ensure food safety. Recently, new biosensor technologies have become a research hotspot due to their characteristics of speed and accuracy. This review describes various technologies such as chromatographic and spectroscopic techniques, ELISA techniques, and biosensing techniques, along with their advantages and weaknesses, for AFB1 control in edible oil and provides new insight into AFB1 detection for future work. Although compared with other technologies, biosensor technology involves the cross integration of multiple technologies, such as spectral technology and new nano materials, and has great potential, some challenges regarding their stability, cost, etc., need further studies.

Advances in fluorescence sensing enabled by lanthanide-doped upconversion nanophosphors

Lanthanide-doped upconversion nanoparticles (UCNPs), characterized by converting low-energy excitation to high-energy emission, have attracted considerable interest due to their inherent advantages of large anti-Stokes shifts, sharp and narrow multicolor emissions, negligible autofluorescence background interference, and excellent chemical- and photo-stability. These features make them promising luminophores for sensing applications. In this review, we give a comprehensive overview of lanthanide-doped upconversion nanophosphors including the fundamental principle for the construction of UCNPs with efficient upconversion luminescence (UCL), followed by state-of-the-art strategies for the synthesis and surface modification of UCNPs, and finally describing current advances in the sensing application of upconversion-based probes for the quantitative analysis of various analytes including pH, ions, molecules, bacteria, reactive species, temperature, and pressure. In addition, emerging sensing applications like photodetection, velocimetry, electromagnetic field, and voltage sensing are highlighted.

Lanthanide ion (Ln3+ )-based upconversion sensor for quantification of food contaminants: A review

The food safety issue has gradually become the focus of attention in modern society. The presence of food contaminants poses a threat to human health and there are a number of interesting researches on the detection of food contaminants. Upconversion nanoparticles (UCNPs) are superior to other fluorescence materials, considering the benefits of large anti-Stokes shifts, high chemical stability, non-autofluorescence, good light penetration ability, and low toxicity. These properties render UCNPs promising candidates as luminescent labels in biodetection, which provides opportunities as a sensitive, accurate, and rapid detection method. This paper intended to review the research progress of food contaminants detection by UCNPs-based sensors. We have proposed the key criteria for UCNPs in the detection of food contaminants. Additionally, it highlighted the construction process of the UCNPs-based sensors, which includes the synthesis and modification of UCNPs, selection of the recognition elements, and consideration of the detection principle. Moreover, six kinds of food contaminants detected by UCNPs technology in the past 5 years have been summarized and discussed fairly. Last but not least, it is outlined that UCNPs have great potential to be applied in food safety detection and threw new insight into the challenges ahead.

Biosensing based on upconversion nanoparticles for food quality and safety applications

Food safety and quality regulations inevitably call for sensitive and accurate analytical methods to detect harmful contaminants in food and to ensure safe food for the consumer. Both novel and well-established biorecognition elements, together with different transduction schemes, enable the simple and rapid analysis of various food contaminants. Upconversion nanoparticles (UCNPs) are inorganic nanocrystals that convert near-infrared light into shorter wavelength emission. This unique photophysical feature, along with narrow emission bandwidths and large anti-Stokes shift, render UCNPs excellent optical labels for biosensing because they can be detected without optical background interferences from the sample matrix. In this review, we show how this exciting technique has evolved into biosensing platforms for food quality and safety monitoring and highlight recent applications in the field.

Simultaneous electrochemical aptasensing of patulin and ochratoxin A in apple juice based on gold nanoparticles decorated black phosphorus nanomaterial

Simultaneous detection of patulin (PAT) and ochratoxin A (OTA) in food products is in great demand, which can prevent toxins from being exposed to human and animal bodies. However, simultaneous detection of multiple targets still faces a challenge. Herein, we developed a novel electrochemical aptasensor for the simultaneous detection of PAT and OTA in apple juice based on gold nanoparticles decorated black phosphorus (AuNPs-BP) nanomaterial. AuNPs-BP function?/work? as a sensing platform for loading much different electrochemical signal molecules functionalized aptamers. In this context, methylene blue functionalized PAT aptamers (Mb-PAT-aptamers) and ferrocene functionalized OTA aptamers (Fc-OTA-aptamers) have been introduced here to fabricate the aptasensor. Fc close to electrode surface showed a strong signal, whereas Mb was far away from electrode surface so exhibited a weak signal in the absence of OTA and PAT. Two kinds of electrochemical signal changes have been recorded dependent on target of OTA and PAT concentrations. So, simultaneous detection of OTA and PAT is achieved. Under the optimum conditions, using this developed biosensor, PAT and OTA can be quantified at a linearity range of 0.01 × 10^-7 μg·mL^-1 ~ 0.10 μg·mL^-1. In addition, it also has good selectivity, stability and repeatability. For the practical application, it shows promising performance for the simultaneous detection of PAT and OTA in apple juice.

Development of a fast and ultrasensitive black phosphorus-based colorimetric/photothermal dual-readout immunochromatography for determination of norfloxacin in tap water and river water

A rapid and ultrasensitive method for colourimetric/photothermal dual-readout detection was developed using an 808 nm NIR laser and a thermal imaging app on mobile phone. Norfloxacin was used as a model contaminant to demonstrate this universal rapid detection method. It is innovatively, to use the advanced two-dimensional material black phosphorus as a colourimetric/photothermal reagent for the first time. The samples were added to the strip, and the analytes were selectively captured on the conjugate pad by monoclonal antibody-modified magnetic/upconversion nanocomposites. The samples flowed through the strips by capillary action until reaching the control line, where immune complex formation occurred due to the presence of secondary antibody. The added black phosphorus could be captured by the the antigens which were directly exposed to the test line and a brown band could be observed by naked eye. Upon illumination by NIR light for 1 min, the real-time temperature is obtained for quantitative analysis through the thermal imaging performed by mobile phone camera. This method can achieve the detection of norfloxacin in water samples within 20 min, and the detection limits of colorimetric and photothermal readout can reach 45 pg mL^-1. Compared with conventional strips, this method provided an increased sensitivity by about two orders of magnitude, with a integrated portable laser and a mobile phone. It is a valuable method for rapid detection and can be applied to other environmental contaminants as well.

Sensors/nanosensors based on upconversion materials for the determination of pharmaceuticals and biomolecules: An overview

Upconversion materials have been the focus of a large body of research in analytical and clinical fields in the last two decades owing to their ability to convert light between various spectral regions and their particular photophysical features. They emit efficient and sharp ultraviolet (UV) or visible luminescence after excitation with near-infrared (NIR) light. These features overcome some of the disadvantages reported for conventional fluorescent materials and provide opportunities for high sensitivity chemo-and bio-sensing. Here, we review studies that used upconversion materials as sensors for the determination of pharmaceuticals and biomolecules in the last two decades. The articles included in this review were retrieved from the SCOPUS database using the search phrases: "upconversion nanoparticles for determination of pharmaceutical compounds", and "upconversion nanoparticles for determination of biomolecules". Details of each developed upconversion nanoparticles based sensor along with their relevant analytical parameters are reported and carefully explained.

Synthesis of a CuNP/chitosan/black phosphorus nanocomposite for non-enzymatic hydrogen peroxide sensing

A copper-chitosan-black phosphorus nanocomposite (CuNPs-Chit-BP) was fabricated by electrochemically depositing copper nanoparticles onto a black phosphorus-modified glassy carbon electrode in chitosan solution. CuNPs demonstrated a uniform distribution on the Chit-BP modified GCE with an average size of 20 nm. Electrochemical methods were used to study the catalytic activity of the CuNPs-Chit-BP nanocomposite toward hydrogen peroxide. The results showed that the synthesized nanocomposite exhibited excellent electrical conductivity, good biocompatibility and highly efficient electrocatalytic activity toward hydrogen peroxide reduction in the range of 10 μM-10.3 mM with a detection limit of 0.390 μM. The present work proposed a new strategy to explore novel BP-based non-enzymatic biosensing platforms.

Calcium-cation-doped polydopamine-modified 2D black phosphorus nanosheets as a robust platform for sensitive and specific biomolecule sensing

Many polymer decorated/modified 2D nanomaterials have been developed as enhanced drug delivery systems and photothermal theranostic nanoagents. However, few reports describe the use of these novel nanomaterials as nanoplatforms for biomolecule sensing. Herein, we used calcium-cation-doped polydopamine-modified (PDA-modified) 2D black phosphorus (BP) nanosheets (BP@PDA) as a sensing nanoplatform for the detection of nucleic acids and proteins in complex biological samples. Fluorescent-dye-labeled single-strand DNA aptamer/probes are adsorbed by the Ca²⁺-doped BP@PDA mediated by calcium-cation coordination. The PDA coating enhances the stability of the inner BP, provides binding sites to DNA nucleobases, and quenches fluorescence. Without any chemical conjugation, this sensing nanoplatform selectively and specifically detects protein (human thrombin, linear range: 10-25 nM, detection limit: 0.02 nM), single-strand DNA (linear range: 1-10 nM, detection limit: 0.52 nM) in 1% serum diluted samples, and senses intracellular mRNAs (C-myc, and actin) in living cells. The nanoplatform exhibits the advantages of both the 2D nanomaterial (BP) and the coating polymer (PDA), naturally enters living cells unaided by transfection agents, resists enzymatic lysis and shows high biocompatibility. This nanoplatform design contributes towards future biomolecule analytical method development based on polymer decorated/modified 2D nanomaterials.

SERS-based immunoassay using gold-patterned array chips for rapid and sensitive detection of dual cardiac biomarkers

Cardiac troponin I (cTnI) and creatine kinase-MB (CK-MB) are important diagnostic biomarkers for acute myocardial infarction (AMI). Many efforts have been undertaken to develop highly sensitive detection methods for the quantitative analysis of these dual targets. However, current immunoassay methods are inadequate for accurate measurement of cTnI and CK-MB, due to their limited detection sensitivity. Thus, there is still an urgent demand for a new technique that will enable ultrahigh sensitive detection of these biomarkers. In this study, we developed a surface-enhanced Raman scattering (SERS)-based sandwich immunoassay platform for the ultrasensitive detection of cTnI and CK-MB. In this study, a monoclonal-antibody-immobilized gold-patterned chip was used as a SERS active template. Target samples and polyclonal-antibody-conjugated Au@Ag core-shell nanoparticles were then added. Using this SERS platform, the concentration of biomarkers could be quantified by monitoring the characteristic Raman peak intensity of Raman reporter molecules. Under optimized conditions, the limits of detection (LODs) were estimated to be 8.9 pg mL-1 and 9.7 pg mL-1 for cTnI and CK-MB, respectively. Thus, the proposed SERS-based immunoassay has great potential to be an effective diagnostic tool for the rapid and accurate detection of cTnI and CK-MB.

Upconversion fluorescent aptasensor for bisphenol A and 17β-estradiol based on a nanohybrid composed of black phosphorus and gold, and making use of signal amplification via DNA tetrahedrons

This study describes an upconversion fluorescent aptasensor based on black phosphorus nanohybrids and self-assembled DNA tetrahedrons dual-amplification strategy for rapid detection of the environmental estrogens bisphenol A (BPA) and 17β-estradiol (E2). Tetrahedron complementary DNAs (T-cDNAs) were self-assembled in an oriented fashion on a 2D nanohybrid composed of black phosphorus (BP) and gold to give a materials of architecture BP-Au@T-cDNAs. In parallel, core-shell upconversion nanoparticles were modified with aptamers (UCNPs@apts) and used as capture probes. On complementary pairing, the BP-Au@T-cDNA quench the fluorescence of UCNPs@apts (measured at an excitation wavelength 808 nm and at main emission peaks at 545 nm and 805 nm.) Compared with single-stranded probes based on black phosphorus and gold, the dual-amplification strategy increases quenching efficiency by nearly 25%-30% and reduces capture time to 10 min. This is due to the higher optical absorption of 2D nanohybrid and the reduction of steric hindrance by T-cDNAs. Exposure to BPA or E2 cause the release of UCNPs@apts from the BP-Au@T-cDNAs due to stronger binding between aptamer and analyte. Hence, fluorescence recovers at 545 nm for BPA and 805 nm for E2. Based on these findings, a dually amplified aptamer assay was constructed that covers the 0.01 to 100 ng mL^-1 BPA concentration range, and the 0.1 to 100 ng mL^-1 E2 concentration range. The detection limits are 7.8 pg mL^-1 and 92 pg mL^-1, respectively. This method was applied to the simultaneous determination of BPA and E2 in spiked samples of water, food, serum and urine. Graphical abstract Schematic presentation of novel quenching probes designed by tetrahedron complementary DNAs oriented self-assembled on the surface of black phosphorus/gold nanohybrids. Combined with aptamer-modified upconversion nanoparticles, a dual-amplification self-assembled fluorescence nanoprobe was constructed for simultaneous detection of BPA and E2.