Selected electrochemical properties of Pd–Au alloys: hydrogen absorption and surface oxidation

Towards High Efficacy of Pd-Au/C Catalyst for Tetrachloromethane Hydrodechlorination

We present an efficient strategy for synthesising the PdAu catalysts with a homogeneous PdAu alloy phase for environmentally important hydrodechlorination of tetrachloromethane in the gas phase. The synthesis of carbon-supported catalysts involved two major steps: (i) incorporation of palladium and gold nanoparticles into carbon support and (ii) activation of the catalysts. The critical part of this work was to find the optimal conditions for both steps. Thus, the incorporation of the nanoparticles was carried out in two ways, by impregnation and direct redox reaction method using acetone solutions of metal precursor salts. The activation was performed either by a conventional thermal reduction in hydrogen or flash irradiation in a microwave oven. The homogeneity and structure of the PdAu alloy were found to depend on the catalyst activation method critically. In all cases, we observed better homogeneity for catalysts that were subject to microwave irradiation. Moreover, the flash microwave irradiation of prepared catalysts provided catalysts of better stability and selectivity towards the desired products (hydrocarbons) in the hydrodechlorination of tetrachloromethane as compared to the catalyst obtained by conventional thermal activation in hydrogen.

Tailorable Electrocatalytic 5-Hydroxymethylfurfural Oxidation and H2 Production: Architecture-Performance Relationship in Bifunctional Multilayer Electrodes

Water electrocatalytic splitting is considered as an ideal process for generating H₂ without byproducts. However, in the water-splitting reaction, a high overpotential is needed to overcome the high-energy barrier due to the slow kinetics of the oxygen evolution reaction (OER). In this study, we selected the 5-hydroxymethylfurfural (HMF) oxidation reaction, which is thermodynamically favored, to replace the OER in the water-splitting process. We fabricated three-dimensional hybrid electrocatalytic electrodes via layer-by-layer (LbL) assembly for simultaneous HMF conversion and hydrogen evolution reaction (HER) to investigate the effect of the nanoarchitecture of the electrode on the electrocatalytic activity. Nanosized graphene oxide was used as a negatively charged building block for LbL assembly to immobilize the two electroactive components: positively charged Au and Pd nanoparticles (NPs). The internal architecture of the LbL-assembled multilayer electrodes could be precisely controlled and their electrocatalytic performance could be modified by changing the nanoarchitecture of the electrode, including the thickness and position of the metal NPs. Even with a composition of the identical constituent NPs, the electrodes exhibited highly tunable electrocatalytic performance depending on the reaction kinetics as well as a diffusion-controlled process due to the sequential HMF oxidation and the HER. Furthermore, a bifunctional two-electrode electrolyzer for both the anodic HMF oxidation and the cathodic HER, which had an optimized LbL-assembled electrode for each reaction, exhibited the best full-cell electrocatalytic activity.

Electrochemistry at Bimetallic Pd/Au Thin Film Surfaces for Selective Detection of Reactive Oxygen Species and Reactive Nitrogen Species

In this work, we designed and fabricated Pd/Au bimetallic thin film electrodes with isolated Pd nanoparticles via underpotential deposition of copper on a gold substrate followed by in situ redox replace reaction in a Pd salt solution. The Pd/Au electrode was characterized by AFM and XPS as well as multiple electrochemical techniques including CV and electrochemical quartz crystal microbalance (EQCM) in sulfuric acid and phosphate buffer electrolytes. Results show that the reduction reactions of the analytes (i.e., H₂O₂ and 3-nitrotyrosine (3-NT)) at the Pd/Au thin film surfaces affect the nature and reactivity of Pd/Au surface electrochemistry including the adsorbed/absorbed hydrogen and/or the premonolayer palladium oxide redox processes at Pd. The EQCM experiment supports the arrangement of small size Pd nanoparticles in the Pd thin film in the presence of gold exhibits unusual properties, acting as a new physicochemical dimension between the electrode and target H₂O₂ and 3-NT molecules. The Pd/Au thin film was demonstrated as an extremely sensitive and selective probe for detection of common ROS and RNS (i.e., H₂O₂ and 3-NT). The integration of two different metallic species, Pd and Au, into a surface structure on nanoscale by exploiting their unique surface electrochemistry establishes an innovative analytical method for highly sensitive and selective detection of H₂O₂ and 3-NT simultaneously. This method has a general scope for detecting a broad range of redox active and nonredox active species simultaneously, which opens up new opportunities to develop new electrocatalytic materials and innovative sensing approaches.

Tuning Catalytic Properties of Supported Bimetallic Pd/Ir Systems in the Hydrogenation of Cinnamaldehyde by Using the “Water-in-Oil” Microemulsion Method

Supported Pd/Ir bimetallic catalysts were synthesized by the “water-in-oil” microemulsion method at different precursor concentrations and characterized by XRD, XPS, SEM, TEM, and cyclic voltammetry. Depending on the preparation conditions, formation of bimetallic catalysts with different metal segregation and surface composition can be easily obtained, thus tuning the bimetallic structure of catalysts as well as their relative catalytic properties. Bimetallic Pd/Ir systems were efficiently tested in the hydrogenation of cinnamaldehyde showing a better performance than analogous monometallic catalysts.

Three-Dimensional Nanostructured Palladium with Single Diamond Architecture for Enhanced Catalytic Activity

Fuel cells are a key new green technology that have applications in both transport and portable power generation. Carbon-supported platinum (Pt) is used as an anode and cathode electrocatalyst in low-temperature fuel cells fueled with hydrogen or low-molecular-weight alcohols. The cost of Pt and the limited world supply are significant barriers to the widespread use of these types of fuel cells. Comparatively, palladium has a 3 times higher abundance in the Earth's crust. Here, a facile, low-temperature, and scalable synthetic route toward three-dimensional nanostructured palladium (Pd) employing electrochemical templating from inverse lyotropic lipid phases is presented. The obtained single diamond morphology Pd nanostructures exhibited excellent catalytic activity and stability toward methanol, ethanol, and glycerol oxidation compared to commercial Pd black, and the nanostructure was verified by small-angle X-ray scattering, scanning tunneling electron microscopy, and cyclic voltammetry.

Asymmetric Au-core Pd-shell nanoparticles supported on reduced graphene oxide for enhanced electrocatalytic activity

Asymmetric Au-core Pd-shell nanoparticles supported on rGO simply prepared by a GRR-like technique exhibit superior ORR performance compared to commercial Pt/C.

Spongelike nanoporous Pd and Pd/Au structures: facile synthesis and enhanced electrocatalytic activity

This paper reports the facile synthesis and characterization of spongelike nanoporous Pd (snPd) and Pd/Au (snPd/Au) prepared by a tailored galvanic replacement reaction (GRR). Initially, a large amount of Co particles as sacrificial templates was electrodeposited onto the glassy carbon surface using a cyclic voltammetric method. This is the key step to the subsequent fabrication of the snPd/Au (or snPd) architectures by a surface replacement reaction. Using Co films as sacrificial templates, snPd/Au catalysts were prepared through a two-step GRR technique. In the first step, the Pd metal precursor (at different concentrations), K2PdCl4, reacted spontaneously to the formed Co frames through the GRR, resulting in a snPd series. snPd/Au was then prepared via the second GRR between snPd (prepared with 27.5 mM Pd precursor) and Au precursor (10 mM HAuCl4). The morphology and surface area of the prepared snPd series and snPd/Au were characterized using spectroscopic and electrochemical methods. Rotating disk electrode (RDE) experiments for oxygen reduction in 0.1 M NaOH showed that the snPd/Au has higher catalytic activity than snPd and the commercial Pd-20/C and Pt-20/C catalysts. Rotating ring-disk electrode (RRDE) experiments reconfirmed that four electrons were involved in the electrocatalytic reduction of oxygen at the snPd/Au. Furthermore, RDE voltammetry for the H2O2 oxidation/reduction was used to monitor the catalytic activity of snPd/Au. The amperometric i-t curves of the snPd/Au catalyst for a H2O2 electrochemical reaction revealed the possibility of applications as a H2O2 oxidation/reduction sensor with high sensitivity (0.98 mA mM(-1) cm(-2) (r = 0.9997) for H2O2 oxidation and -0.95 mA mM(-1) cm(-2) (r = 0.9997) for H2O2 reduction), low detection limit (1.0 μM), and a rapid response (<∼1.5 s).

Hydrogen electrosorption into Pd-Cd nanostructures

Hydrogen-absorbing materials are crucial for both the purification and storage of hydrogen. Pd and Pd-based alloys have been studied extensively for their use as both hydrogen dissociation catalysts and hydrogen selective membrane materials. It is known that incorporating metal atoms of different sizes into the Pd lattice has a major impact on the hydrogen absorption process. In this paper, hydrogen electrosorption into nanostructured Pd-Cd alloys has been studied for different compositions of Cd that varied from 0 to 15 at. %. The low cost of Cd makes it an attractive material to combine with Pd for hydrogen sorption. A combination of chronoamperometry and cyclic voltammetric experiments was used to determine the ratio of the H/(Pd + Cd) and the kinetics of hydrogen sorption into these Pd-Cd alloys at different potentials. It was found that the maximum H/(Pd + Cd) value was 0.66 for pure Pd, and this decreased with increasing the amount of Cd. Also, the alpha (solid solution) to beta phase (metal hydride) hydrogen transition was determined to be the slowest step in the absorption process and was practically eliminated when an optimum amount of Cd atoms was doped (i.e., Pd-Cd(15%)). With increasing the amount of Cd, more hydrogen was absorbed into the Pd-Cd nanostructures at the higher potentials (the alpha phase region). The faster kinetics, along with the decrease in the phase transition of hydrogen sorption into the Pd-Cd nanostructures when compared to pure Pd, makes the Pd-Cd nanostructures attractive for use as a hydrogen dissociation catalytic capping layer for other metal hydrides or as a hydrogen selective membrane.