Dentin pretreatment with Er:YAG laser and sodium ascorbate to improve the bond strength of glass fiber post

Effect of fit and self-etching adhesive on fiber post retention in endodontically treated teeth

BACKGROUND

Fiber post (FP) reinforced restoration was widespread in endodontically treated teeth, of which the retention was closely related to fit and operation process. However, the question whether the fit and self-etching adhesive (SED) affect the success of FP restoration still remained unclear.

OBJECTIVE

This research aimed to assess how the fit and self-etching adhesive (SED) impact the pull-out bond strength (BS) of glass fiber-reinforced composite posts from the root canal dentin.

METHODS

Eighty lower first premolars underwent simulated endodontic treatment, after which their canals were shaped to accommodate a size three RelyX fiber post (FP) (diameter 1.9 mm). They were then divided into 4 equal groups [Unfit post and no SEA (Group UN), Fit post and no SEA (Group FN), Unfit post with SEA (Group UA) and Fit post with SEA (Group FA)] using two different sized FPs and SEA. Cement thickness was acquired by histological analysis and stereomicroscopy. Each sample was tested for pull-out strength through a universal testing machine. Based on the pull-out test, the failure types were observed and scored by visualizing through a stereomicroscope.

RESULTS

Group FA demonstrated significantly greater BS compared to Group UN and Group UA, with Group UN showing a statistically significant difference at p< 0.01 and Group UA at p< 0.05. Main failure types in Group FA were Type II, which illustrated that the cement detachment mainly occurred from the post-cement interface. Therefore, Group FA possessed the STRONGEST BS and was most suitable for FP-reinforced crown restorations.

CONCLUSIONS

Both the fit and SEA enhanced the pull-out BS. The SEA was critical for BS promotion when the mechanical retention was inadequate.

In Vitro Bond Strength of Dentin Treated with Sodium Hypochlorite: Effects of Antioxidant Solutions

This systematic review aims to evaluate whether the application of antioxidant solutions can enhance the bond strength of resin-based materials to sodium hypochlorite (NaOCl)-treated dentin. This study follows the PICOT strategy: population (sodium hypochlorite-treated dentin), intervention (application of antioxidants), control (distilled water), outcome (bond strength), and type of studies (in vitro studies). The systematic review and meta-analysis were conducted following PRISMA guidelines. Electronic databases were searched for in vitro studies evaluating the effects of antioxidants on bond strength to sodium hypochlorite-treated dentin. Two independent reviewers screened articles, extracted data, and assessed risk of bias. Meta-analyses were performed using a random-effects model to compare standardized mean differences in bond strength between antioxidant pretreatment and control groups. Inclusion criteria consisted of in vitro studies that examined the bond strength of resin-based materials to NaOCl-treated dentin with antioxidant application, while exclusion criteria included studies with incomplete data, those not using a control group, or those that did not directly measure bond strength. From 3041 initial records, 29 studies were included in the qualitative analysis and 25 in the meta-analysis. Ascorbic acid, sodium ascorbate, grape seed extract, green tea, and rosmarinic acid significantly improved bond strength to sodium hypochlorite-treated dentin (p < 0.05). The effectiveness of grape seed extract varied with adhesive system type. Hesperidin, p-toluene sulfonic acid, and sodium thiosulfate did not significantly improve bond strength. Most studies had a high risk of bias. This suggests that the conclusions drawn from these studies should be interpreted with caution, and further research with more robust methodologies may be needed to confirm the findings. In conclusion, this systematic review implies that certain antioxidants can improve bond strength to sodium hypochlorite-treated dentin, with efficacy depending on the specific agent and adhesive system used. Further standardized studies are needed to optimize protocols and confirm these findings.

Glycolic acid on push-out bond strength of fiber post and smear removal: an in vitro study

This study aims to investigate glycolic acid (GA) as a final irrigant on push-out bond strength of fiber post and smear removal. Ninety mandibular premolars were stabilized with a silicone key and photographed, and canal cross-section was calculated by image processing software. Round canal morphology was selected. The specimens were divided into five groups (n = 18); 10%GA, 17%EDTA, NaOCl + 10%GA, NaOCl + 17%EDTA, and the control. Fifteen specimens were used for the push-out. Three specimens were evaluated using a scanning electron microscope after post space preparation. Two-way ANOVA and Chi-square were used for statistics. GA presented higher strength than EDTA (p < 0.05). The NaOCl + GA showed higher strength than the NaOCl + EDTA (p < 0.05). The highest values were observed in cervical and lowest in apical thirds (p < 0.05). The most failure type was between dentin and resin (p < 0.05). GA removed the smear in the post space including the apical third. The NaOCl + GA has superiority to NaOCl + EDTA on push-out strength. Glycolic acid improved the bond strength of fiber post when used as a final post space irrigant. The combination of NaOCl and glycolic acid did not negatively affect the bond strength and was more effective compared to the combination with EDTA. Glycolic acid improved the bond strength of fiber post when used as a final post space irrigant. The combination of NaOCl and glycolic acid did not negatively affect the bond strength and was more effective compared to the combination with EDTA.

Effect of antioxidants after post-space irrigation on the adhesive interface of glass fiber post cementation

OBJECTIVE

This study evaluated the effects of antioxidants, 10% sodium ascorbate (SA) or 20% alpha-tocopherol (AT), after post-space irrigation with 2.5% sodium hypochlorite +17% EDTA (SH) or 1% peracetic acid (PA) on the adhesive interface after glass fiber post cementation.

MATERIALS AND METHODS

Sixty bovine roots were endodontically treated. After preparation, the post-space was irrigated with SH or PA followed or not by the use of antioxidants (SA or AT) (n = 10). Push-out bond strength test, failure mode, and dentin penetrability analysis using confocal laser microscope were performed in the cervical, middle, and apical thirds. Data from bond strength and dentinal penetrability were evaluated by one-way ANOVA and Tukey post hoc test (p < 0.05).

RESULTS

SH showed the lowest bond strength regardless of the third (p < 0.05). In apical third, mixed failure was the most incident in all groups. Only in the cervical third of the post-space, SH-AT provided the greatest tag extension of the cementation system into dentin (p < 0.05). However, in the middle and apical thirds, SH-AT, SH-SA, and PA-SA provided the largest tag extensions (p < 0.05), but similar to each other (p > 0.05).

CONCLUSIONS

The use of antioxidants only favored bond strength when SH was used and dentin penetrability of the adhesive and conventional resin cementation, regardless of the solution used to irrigate the post-space.

CLINICAL SIGNIFICANCE

The use of antioxidants (10% sodium ascorbate and 20% alpha-tocopherol) after post-space irrigation with sodium hypochlorite appears to increase the bond strength favoring the glass fiber post-cementation.

Evaluation of Er:YAG and Er,Cr:YSGG lasers on intraradicular bonding using modified glass fiber tips

The aim of this study was to determine whether erbium laser irradiation emitted by modified glass-fiber tips would improve the intraradicular bonding of fiber posts. Forty human canines were endodontically treated and prepared for fiber-post placement. Roots were divided into five groups (n=8); according to the laser-tip combinations (2,940 nm Er:YAG and 2,780 nm Er,Cr:YSGG). Non-irradiated root canals served as control. Posts were cemented with self-adhesive resin cement and subjected to push-out test. Failure modes were characterized, and intraradicular bonded interfaces were analyzed by SEM and submitted to nanoleakage evaluation. Data were analyzed by two-way ANOVA and Tukey test (α=0.05). No significant differences were observed in cervical and middle sections (p>0.05), while significantly higher bond strengths were observed in apical sections (p<0.05). Laser irradiation reduced adhesive failures, cement-dentin gap formation, and nanoleakage apically. Laser-irradiation protocols employing end- or radial-firing tips improved bonding to apical intraradicular dentin contributing to more uniform bonded interfaces.

The combined treatment of fiber post and root canal by the Er:YAG laser enhances the bond strength of composite reconstruction

Fiber post bonding failure remains an issue during crown restoration procedures. This experiment examines the bonding effect of combined Er:YAG laser treatment on both root canal and fiber post. Sixty extracted mandibular first premolars were randomly selected and divided into 6 groups (n = 10 per group): G1 (control group): root canal with 2.5% NaClO treatment, no treatment of fiber post; G2: root canal with 2.5% NaClO treatment and fiber post with airborne-particle abrasion; G3: root canal with Er:YAG laser treatment and fiber post with airborne-particle abrasion; G4: root canal with Er:YAG laser treatment, no treatment of fiber post; G5: root canal with 2.5% NaClO treatment, fiber post with Er:YAG laser irradiation; G6: combined Er:YAG laser irradiation of both root canal and fiber post. An Er:YAG laser with a wavelength of 2940 nm was used to treat the fiber post (4.5 W, 450 mJ, 10 Hz for 60 s at 100-μs pulse duration with 100% water cooling) and the root canal (1.5 W, 150 mJ, 10 Hz for 60 s at 100-μs pulse duration with 100% water cooling). When the root canal was treated with the laser, the fiber tip was inserted into the root canal to make a spiral reciprocating motion. Bond strength was analyzed by a micro push-out test. Data were analyzed using both the Tukey test and two-way ANOVA (α = 0.05). Failure modes were observed and counted through a stereo microscope. The root canal and fiber post surface analysis was performed using SEM. The bond strength of G3 and G6 were significantly enhanced compared to those of the other groups (p < 0.05). The SEM analysis showed that the smear layers of groups with root canals subjected to Er:YAG laser irradiation were significantly reduced compared to those of the control group (G1). In groups with fiber posts treated with Er:YAG laser irradiation, the surfaces of the fiber posts exhibited greater surface roughness and a certain degree of epoxy matrix removal. Through the combined Er:YAG laser irradiation of both root canal and fiber post, the bond strength between them was significantly enhanced, which was superior to the individual treatment of either fiber posts or root canal.

Effect of nanosecond- and microsecond-pulse Er,Cr:YSGG laser ablation on dentin shear bond strength of universal adhesives

OBJECTIVE

The study aimed to evaluate the bond strength of universal adhesives to dentin after Er,Cr:YSGG laser irradiation with nanosecond-domain and microsecond-domain pulses.

METHODS

Eighty extracted caries-free, sound human molars were divided into eight groups. The enamel was removed until the dentin occlusal flat dentin surface was exposed. Etch-and-rinse followed by adhesive was applied to group 1, and a self-etch adhesive was applied to group 2. Er,Cr:YSGG laser (3 mJ, 100 Hz, 100 ns), (3 mJ, 100 Hz, 150 μs), and (20 mJ, 100 Hz, 150 μs) were applied to groups 3-4, 5-6, and 7-8, respectively. The laser preparation was followed by self-etch adhesives or adhesives treatment. When the composite resin had been built up on the samples, the shear bond strength was tested, and the data were statistically analyzed using analysis of variance (ANOVA).

RESULTS

Groups prepared with nanosecond-pulse laser showed significantly higher bond strength values than the microsecond-pulse laser groups and self-etch mode group, and the SEM photographs also showed more dentinal tubules and no damage in the ablation area. The shear bond strength of long pulse laser ablated was comparable to that of self-etching system when it was combined with a self-etch adhesive at low energy, but higher energy laser degraded shear bond strength.

CONCLUSIONS

The pulse width of Er,Cr:YSGG laser affects the bond strength, nanosecond pulses of laser irradiation without water cooling can enhance bond strength, but microsecond pulses of laser cannot enhance bond strength.

Effect of Er:YAG laser irrigation with different etching modes on the push-out bond strength of fiber posts to the root dentine

The objective of this study was to evaluate the effect of Er:YAG laser irrigation on the push-out bond strength of fiber posts to the root dentine. Sixty extracted human mandibular first premolars were collected and decoronated. The residual roots received endodontic treatment. The treated roots were randomly divided into three groups according to different irrigation protocols: group LAI (Er:YAG laser–activated irrigation), group PUI (passive ultrasonic irrigation, positive control), and group CSI (conventional syringe irrigation, negative control) (n = 20). Each group was divided into two subgroups, either total-etching modes or self-etching modes (n = 10). After fiber post restoration, all roots were sectioned into seven 1.0-mm-thick slices. The slices received a push-out test by a universal test machine. The resin tag on the segments’ bonding interfaces was observed by scanning electron microscope. There were significant differences in the effects of the irrigation method, bonding modes, and root regions on the push-out bond strength among the groups (p < 0.05). The specimens with Er:YAG laser–activated irrigation and self-etching mode showed significantly the highest bonding strength (p < 0.001). The lengths and densities of resin tags in group PUI or group LAI with self-etching modes were longer than those in group CSI with total-etching modes. The laser-activated irrigation with self-etching modes improved the bond strength of fiber post to root dentine compared to the passive ultrasonic irrigation or conventional syringe irrigation with total or self-etching modes.

Effectiveness of photodynamic therapy on bonding strength and failure modes of fiber-posts in c-shaped treated root canals

AIM

The present study aimed to assess the push-out bond strength (PBS) and failure modes of fiber-posts after photodynamic therapy (PDT) and Erbium yttrium scandium gallium garnet (Er,Cr:YSGG) in c-shaped canals.

METHODS

Sixty molars with c-shaped root configuration were studied. The endodontic prepared teeth specimen were equally randomized into four groups: i) photodynamic therapy (PDT); ii) Er,Cr:YSGG; iii) chlorhexidine and; iv) control group. Post root filling, 10 mm space was prepared for insertion of post in the root canals. The push-out bond strength was evaluated using Universal testing machine. Modes of failure were evaluated as adhesive, cohesive and admixed. Mean values were computed between groups using Kruskal-Wallis test followed by Bonferroni post hoc test. Comparison between two thirds of root sections were analyzed using Friedman test. P-value was set at 0.05 or less.

RESULTS

Specimens treated with PDT reported the highest mean PBS (8.56 ± 2.12 MPa), while the lowest PBS was observed in NaOCl group (6.92 ± 2.21 MPa). Thirteen failures were observed at the adhesive post interface, whereas 22 failures were found at the interface forming between the dentin surface and adhesive. Similarly, 9 failures were categorized as mixed. For PDT group, a sum of 3 failures and 4 failures were noted at the apical and cervical points.

CONCLUSION

The specimens treated with PDT showed the highest push out bond strength with least number of failures.in c-shaped root canals.

Efficiency of Erbium-Doped Yttrium Aluminum Garnet Laser in Debonding Cemented Glass Fiber Posts: an in vitro Study

Statement of the Problem:

The efficacy of erbium-doped yttrium aluminum garnet (Er; YAG) laser on the debonding properties of certain post materials has remained largely unexplored.

Purpose:

This study aimed to investigate the effect of Er; YAG laser irradiation on debonding of cemented glass fiber posts in root canal treated teeth.

Materials and Method:

In this in vitro study, forty root canal treated mandibular premolar teeth were used in this study. Glass fiber posts were bonded using Panavia F 2.0 cement in the root canal space, and samples were divided into two groups. In the test group, samples were exposed to laser radiation of 7W, 350mJ, frequency of 20Hz and discontinued washing spray. In the control group, samples were left untouched. In each group, samples were sectioned into 1.5mm thick slices from the coronal, middle, and apical thirds of the root (N=120). Tensile bond strengths were evaluated using the push-out test and the failure patterns were evaluated using scanning electron microscopy (SEM). To compare the laser and non-laser groups at each location, independent sample t test was applied, and to compare bond strength between the locations in each group, one-way ANOVA and Tukey’s HSD post hoc was applied.

Results:

A significant difference in tensile strength was observed between the laser-irradiated group and control group; tensile bond strength was much higher in the control group (p<0.001). The highest frequency of fractures was observed at the cement-dentin interface. Given the used parameters, complete debonding was not achieved in the laser-irradiated group.

Conclusion:

Laser radiation reduced the bond strength of glass fiber posts to resin cement without complete debonding.

Photon-Induced Photoacoustic Streaming Activation of the Postbleaching Antioxidant Application Rapidly Improves Bonding to Pulp Chamber Dentin

Objective: This study explored whether the erbium/yttrium/aluminum/garnet (Er:YAG) laser irradiated through the photon-induced photoacoustic streaming (PIPS) method would impact on the resin bonding to pulp chamber dentin when used to activate bleaching and/or postbleaching antioxidant treatment. Materials and methods: One hundred five dentin samples prepared from freshly extracted human incisors were randomly assigned to seven groups (n = 15): control (no bleaching/antioxidant); CB (conventional bleaching only); MB (modified bleaching only); CB-NI (conventional bleaching+antioxidant with needle irrigation); MB-NI (modified bleaching+antioxidant with needle irrigation); CB-PIPSI (conventional bleaching+antioxidant with PIPS-activated irrigation); and MB-PIPSI (modified bleaching+antioxidant with PIPS-activated irrigation). Bleaching (40% hydrogen peroxide) lasted for 20 min. Modified bleaching groups were irradiated with Er:YAG laser using the PIPS tip (2940 nm, 0.90 W, 30 Hz, 30 mJ/pulse, 50-μsec pulse duration) during the first 60 sec of the procedure. The antioxidant treatment with 10% sodium ascorbate lasted for 60 sec. PIPS-activated antioxidant groups were irradiated with Er:YAG laser using the PIPS tip (2940 nm, 0.30 W, 15 Hz, 20 mJ per pulse, 50-μsec pulse duration) throughout the procedure. After completing the composite restorations, all samples were subjected to 5000 thermocycling and the shear bond strength (SBS) test at a crosshead speed of 1 mm/min. SBS data were analyzed using the Kruskal-Wallis test with Bonferroni correction (α& 0.05). Results: No significant difference was detected among the control, CB-PIPSI, and MB-PIPSI (p > 0.05), which presented a significantly higher SBS compared with the other groups (p < 0.05). Conclusions: Irrespective of the application mode of the initial bleaching, PIPS-activated irrigation of the antioxidant improved SBS to bleached dentin to the level of the control in 1 min. Postbleaching antioxidant treatment combined with the PIPS method might be a promising approach to enable immediate resin restoration of bleached dentin.

The effect of a root-dentin pretreatment technique combining PIPS with MTAD aiming to improve the bond strength of glass fiber post

The aim of this study was to evaluate the combined effect of MTAD and photon-induced photoacoustic streaming (PIPS) technique on the smear layer removal and the bond strength of glass fiber post. Fifty-five human mandibular premolars were chosen. After root canal therapy and post space preparation, the teeth were equally divided to five groups according to the methods of root-dentin pretreatment: G1: distilled water (control); G2: 2.5% NaOCl+17% EDTA; G3: MTAD; G4: PIPS; G5: MTAD+PIPS. One sample was randomly selected from each group, and scanning electron microscope (SEM) was used to observe the microscopic morphology of the coronal, middle and apical level of the root-dentin. The remaining ten samples from each group were glued to glass fiber posts, and the bond strength was assessed by push-out test. SEM evaluation showed that the most complete smear layer removal was found in MTAD + PIPS group, especially in coronal third. Push-out test results exhibited that there was a statistically significant interaction between the experimental groups and root canal third (p < .0005). Significant differences could be found among five groups (p < .05): G5 > G4 > G3 > G2 > G1. G5 had the highest bond strength. In conclusion, post space pretreatments with MTAD or PIPS technique can significantly remove smear layer and improve the bond strength of glass fiber post, and combination of them works best.

The Effect of Diode and Er,Cr:YSGG Lasers on the Bond Strength of Fiber Posts

Background: Laser irradiation modifies the topography and composition of dentin surface aiming to increase the retention of bonded posts. Objective: To assess the effect of dentin irradiation with Er,Cr:YSGG or diode lasers on the bond strength of fiber posts using self-adhesive resin cement. Materials and methods: Sixty bovine root canals were root-canal treated, post spaces were prepared, and subsequently fiber posts were cemented. The samples were distributed according to the surface treatment: distilled water (control), Er,Cr:YSGG (1.5 W, 20 sec), or diode (1.5 W, 20 sec) lasers. Bond strengths were assessed by pull-out (n = 10) or push-out testing (n = 10). Pearson's correlation was calculated. Failure mode after testing and the depth of tags in the dentinal tubules were analyzed by confocal laser microscopy. Data were submitted to analysis of variance and Tukey's test. A p < 0.05 was considered significant. Results: In the push-out test, Er,Cr:YSGG laser had significantly different higher values (5.43 ± 0.10 MPa) compared to the control (4.79 ± 0.05 MPa). Diode laser values were not significantly different from the other groups (5.12 ± 0.27 MPa). In the pull-out test, there were no significant differences between Er,Cr:YSGG (6.86 ± 2.16 MPa) and diode (8.43 ± 1.77 MPa) lasers, and both had significant differences compared to the control (4.18 ± 1.29 MPa). No correlation was found. Adhesive failures were predominant in all groups, and no significant differences in tag penetration among the groups were found. Conclusions: The Er,Cr:YSGG laser increases the bond strength of resin cement and fiber post to dentin in both tests, compared to control group without laser treatment. Diode laser only enhanced bonding for pull-out test.