Monitoring biofilm thickness using a non-destructive, on-line, electrical capacitance technique

An Effective Sanitizer for Fresh Produce Production: In Situ Plasma-Activated Water Treatment Inactivates Pathogenic Bacteria and Maintains the Quality of Cucurbit Fruit

The effect of plasma-activated water (PAW) generated with a dielectric barrier discharge diffusor (DBDD) system on microbial load and organoleptic quality of cucamelons was investigated and compared to the established sanitizer, sodium hypochlorite (NaOCl). Pathogenic serotypes of Escherichia coli, Salmonella enterica, and Listeria monocytogenes were inoculated onto the surface of cucamelons (6.5 log CFU g-1) and into the wash water (6 log CFU mL-1). PAW treatment involved 2 min in situ with water activated at 1,500 Hz and 120 V and air as the feed gas; NaOCl treatment was a wash with 100 ppm total chlorine; control treatment was a wash with tap water. PAW treatment produced a 3-log CFU g-1 reduction of pathogens on the cucamelon surface without negatively impacting quality or shelf life. NaOCl treatment reduced the pathogenic bacteria on the cucamelon surface by 3 to 4 log CFU g-1; however, this treatment also reduced fruit shelf life and quality. Both systems reduced 6-log CFU mL-1 pathogens in the wash water to below detectable limits. The critical role of superoxide anion radical (·O2-) in the antimicrobial power of DBDD-PAW was demonstrated through a Tiron scavenger assay, and chemistry modeling confirmed that ·O2- generation readily occurs in DBDD-PAW generated with the employed settings. Modeling of the physical forces produced during plasma treatment showed that bacteria likely experience strong local electric fields and polarization. We hypothesize that these physical effects synergize with reactive chemical species to produce the acute antimicrobial activity seen with the in situ PAW system. IMPORTANCE Plasma-activated water (PAW) is an emerging sanitizer in the fresh food industry, where food safety must be achieved without a thermal kill step. Here, we demonstrate PAW generated in situ to be a competitive sanitizer technology, providing a significant reduction of pathogenic and spoilage microorganisms while maintaining the quality and shelf life of the produce item. Our experimental results are supported by modeling of the plasma chemistry and applied physical forces, which show that the system can generate highly reactive ·O2- and strong electric fields that combine to produce potent antimicrobial power. In situ PAW has promise in industrial applications as it requires only low power (12 W), tap water, and air. Moreover, it does not produce toxic by-products or hazardous effluent waste, making it a sustainable solution for fresh food safety.

Real-Time Monitoring of Biofilm Formation Using a Noninvasive Impedance-Based Method

Biofilms are complex three-dimensional microbial communities that adhere to a variety of surfaces and interact with their surroundings. Because of the dynamic nature of biofilm formation, establishing a uniform technique for quantifying and monitoring biofilm volume, shape, and features in real-time is challenging. Herein, we describe a noninvasive electrochemical impedance approach for real-time monitoring of dental plaque-derived multispecies biofilm growth on a range of substrates. A working equation relating electrochemical impedance to live biofilm volume has been developed that is applicable to all three surfaces examined, including glass, dental filling resin, and Ca2+-releasing resin composites. Impedance changes of 2.5, 35, 50, and 65% correlated to biofilm volumes of 0.10 ± 0.01, 16.9 ± 2.2, 29.7 ± 2.3, and 38.6 ± 2.8 μm3/μm2, respectively. We discovered that glass, dental filling resin, and Ca2+-releasing dental composites required approximately 3.5, 4.5, and 6 days, respectively, to achieve a 50% change in impedance. The local pH change at the biofilm-substrate interfaces also monitored with potentiometry pH microsensor, and pH change varied according to biofilm volume. This impedance-based technique can be a useful analytical method for monitoring the growth of biofilms on a variety of substrates in real-time. Therefore, this technique may be beneficial for examining antibacterial properties of novel biomaterials.

Silicone Oil Decreases Biofilm Formation in a Capacitance-Based Automatic Urine Measurement System

Capacitance-based automatic urine measurement is a validated technique already implemented in clinical practice. However, albuminuria and free hemoglobinuria cause progressive biofilm buildup on the capacitance sensors of the urinometers. The aim of this experimental study is to investigate the influence of albumin and free hemoglobin on the capacitance signal of an automatic urinometer with and without the addition of silicone oil. A solution of Ringer’s acetate mixed with either albumin or free hemoglobin was run through an automatic urinometer containing either a water-soluble capsule with silicone oil or not. In total, around 500 capacitance measurements were retrieved from the albumin and free hemoglobin group, respectively. The mean increase in capacitance in the albumin 3 g/L group was 257 ± 100 pF without and 105 ± 30 pF with silicone oil, respectively, during 24 h. After ten hours of recording, differences between the two albumin groups reached statistical significance. For the free hemoglobin groups (0.01 g/L), the mean increase in capacitance was 190 ± 170 pF with silicone oil, and 324 ± 80 pF without, with a significant difference between the groups after 20 h and onwards. Coating of the capacitance measurement membrane of the automatic urinometer by albumin or free hemoglobin was significantly decreased by silicone oil, prolonging the functionality of the device.

A Novel Method to Reveal a Ureolytic Biofilm Attachment and In Situ Growth Monitoring by Electrochemical Impedance Spectroscopy

The formation of biofilms capable of efficiently carrying out ureolysis is of fundamental importance in several biotechnological systems such as urinary tract infections, building materials and municipal wastewater treatment. This work proposes a straightforward method for the formation of a ureolytic biofilm attached to graphite. The proposed strategy reduced the time needed to complete ureolysis to 3 days instead of 16 days required in suspension culture. To confirm the formation of a ureolytic biofilm, scanning electron microscopy and confocal laser scanning microscopy studies were employed ex situ. However, it is imperative to analyse the biofilm by direct non-invasive techniques. Accordingly, open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) were used as in situ monitoring techniques. The reduction in OCP from - 0.01 to - 0.2 V vs. Ag/AgCl and the increase in capacitance from 200 to 260 μF cm^-2 were related to biofilm attachment. To the best of our knowledge, this is the first time in which a ureolytic biofilm attachment has been analysed by EIS. The increase in the biomass from 0.04 to 2.81 μm³ μm^-2 and in average thickness from 10.19 to 32.78 μm was related to biofilm maturation.

Monitoring of biofilm aging in a Sphingomonas sp. strain from public drinking water sites through changes in capacitance

This study reports the applicability of a capacitance-based technique for evaluating the biofilm progression of Sphingomonas sp. One hundred and forty isolates of Sphingomonas were screened from public drinking water sites, and one potential strain with biofilm-forming ability was used for the study. The biofilm production by this strain was established in microtiter plates and aluminum coupons. The standard biofilm-forming strain Sphingomonas terrae MTCC 7766 was used for comparison. Changes in biofilm were analyzed by energy-dispersive X-ray spectroscopy (EDX) and scanning electron microscope (SEM). Capacitance values were measured at 1, 100 and 200 kHz frequency; however, 1 kHz was selected since resulted in reproducible values, which could be correlated to biofilm age measured as dry weight over a time of 96 h (4 days) depicting the biofilm growth/progression over time. The EDX, SEM and capacitance values obtained in parallel indicated the related physiological profile usually displayed by biofilms upon growth, suggesting authenticity to the observed capacitance profile. The results of this study demonstrated the feasibility of a capacitance-based method for analyzing biofilm development/progression by Sphingomonas sp. and suggested a simple approach for developing an online system to detect biofilms by this opportunistic pathogen of concern in drinking water.

Biodegradation or simple adsorption to the support material? Development of a simple, fast and low-cost technique

Biofilms are present in several areas and are studied in microbiology, medical sciences, biology and, of course, sanitary engineering. Biofilms are used for the treatment of municipal wastewater, and their application was even before the invention of the activated sludge process. The main objective of this work was to develop a simple, fast and low-cost technique to evaluate the nature of the first decay in the concentration of an organic compound in the presence of a solid material. Though simple, the technique developed has allowed the clarification of whether the initial concentration decay is due to adsorption to the support material or a result of biodegradation. The results show that, with two different support materials, adsorption does not take place, and the biodegradation processes are responsible for the first decay in the organic concentration. The technique used offers a fast and low-cost way of studying the existence of adsorption. Two feed concentration solutions and two different support materials were used.

Biofilm thickness measurement using an ultrasound method in a liquid phase

In this report, the development of an online, noninvasive, measurement method of the biofilm thickness in a liquid phase is presented. The method is based in the analysis of the ultrasound wave pulse-echo behavior in a liquid phase reproducing the real reactor conditions. It does not imply the removal of the biomass from the support or any kind of intervention in the support (pipes) to detect and perform the measurements (non-invasiveness). The developed method allows for its sensor to be easily and quickly mounted and unmounted in any location along a pipe or reactor wall. Finally, this method is an important innovation because it allows the thickness measurement of a biofilm, in liquid phase conditions that can be used in monitoring programs, to help in scheduling cleaning actions to remove the unwanted biofilm, in several application areas, namely in potable water supply pipes.

CO2 production as an indicator of biofilm metabolism

Biofilms are important in aquatic nutrient cycling and microbial proliferation. In these structures, nutrients like carbon are channeled into the production of extracellular polymeric substances or cell division; both are vital for microbial survival and propagation. The aim of this study was to assess carbon channeling into cellular or noncellular fractions in biofilms. Growing in tubular reactors, biofilms of our model strain Pseudomonas sp. strain CT07 produced cells to the planktonic phase from the early stages of biofilm development, reaching pseudo steady state with a consistent yield of approximately 10(7) cells.cm(-2).h(-1) within 72 h. Total direct counts and image analysis showed that most of the converted carbon occurred in the noncellular fraction, with the released and sessile cells accounting for <10% and <2% of inflowing carbon, respectively. A CO(2) evolution measurement system (CEMS) that monitored CO(2) in the gas phase was developed to perform a complete carbon balance across the biofilm. The measurement system was able to determine whole-biofilm CO(2) production rates in real time and showed that gaseous CO(2) production accounted for 25% of inflowing carbon. In addition, the CEMS made it possible to measure biofilm response to changing environmental conditions; changes in temperature or inflowing carbon concentration were followed by a rapid response in biofilm metabolism and the establishment of new steady-state conditions.