Aspirin and paracetamol removal using a commercial micro-sized TiO2 catalyst in deionized and tap water

Visible Light Photocatalytic Degradation of Methylene Blue Dye and Pharmaceutical Wastes over Ternary NiO/Ag/TiO2 Heterojunction

Ternary NiO/Ag/TiO2 heterojunction photocatalyst was prepared by deposition coprecipitation for visible light photocatalytic applications. Physicochemical properties of the synthesized NiO/Ag/TiO2 composite were characterized by X-ray diffraction, Brunauer-Emmett-Teller surface area measurement method, transmission electron microscopy, energy-dispersive X-ray spectroscopy techniques, X-ray photoelectron spectroscopy technique, and ultraviolet-visible absorption spectroscopy. The results suggest that the well-dispersed small metallic silver nanoparticles (<3 nm) facilitate electron transfer and bridge nickel oxide and titanium oxide. The photocatalytic degradation and the methylene blue (MB) dye kinetics were carried out on a ternary NiO/Ag/TiO2 composite and compared to bare TiO2 under visible light irradiation. The results indicate that NiO/Ag/TiO2 has superior MB photodegradation efficiency with a high reaction rate constant and low degradation time (93.15% within 60 min) compared to Ag/TiO2, NiO/TiO2, and bare TiO2. NiO/Ag/TiO2 nanocomposite was also investigated for the most common pharmaceutical waste degradation and exhibited excellent degradation efficiency. The enhancement of the composite's performance could be attributed to the surface plasmonic resonance of the Ag nanoparticles, the formation of Schottky junctions at the Ag-TiO2 and Ag-NiO interface, and the p-n heterojunction between NiO and TiO2. Ag NPs act as a photosynthesizer and a photocatalyst, facilitate electron transfer, shift the absorption to the visible light region, reduce the band gap of TiO2, suppress the electron-hole recombination, and enhance the photocatalytic activity and stability as a result.

Stochastic Dynamic Mass Spectrometric Quantitative and Structural Analyses of Pharmaceutics and Biocides in Biota and Sewage Sludge

Mass spectrometric innovations in analytical instrumentation tend to be accompanied by the development of a data-processing methodology, expecting to gain molecular-level insights into real-life objects. Qualitative and semi-quantitative methods have been replaced routinely by precise, accurate, selective, and sensitive quantitative ones. Currently, mass spectrometric 3D molecular structural methods are attractive. As an attempt to establish a reliable link between quantitative and 3D structural analyses, there has been developed an innovative formula [DSD″,tot=∑inDSD″,i=∑in2.6388.10−17×Ii2¯−Ii¯2] capable of the exact determination of the analyte amount and its 3D structure. It processed, herein, ultra-high resolution mass spectrometric variables of paracetamol, atenolol, propranolol, and benzalkonium chlorides in biota, using mussel tissue and sewage sludge. Quantum chemistry and chemometrics were also used. Results: Data on mixtures of antibiotics and surfactants in biota and the linear dynamic range of concentrations 2–80 ng.(mL)−1 and collision energy CE = 5–60 V are provided. Quantitative analysis of surfactants in biota via calibration equation ln[D″SD] = f(conc.) yields the exact parameter |r| = 0.99991, examining the peaks of BAC-C12 at m/z 212.209 ± 0.1 and 211.75 ± 0.15 for tautomers of fragmentation ions. Exact parameter |r| = 1 has been obtained, correlating the theory and experiments in determining the 3D molecular structures of ions of paracetamol at m/z 152, 158, 174, 301, and 325 in biota.

Photocatalytic degradation of triclocarban in aqueous solution using a modified zeolite/TiO2 composite: kinetic, mechanism study and toxicity assessment

The current work aimed to investigate the degradation of the triclocarban (TCC) in aqueous solution using a modified zeolite/TiO₂ composite (MZTC) synthesized by applying the electrochemical anodization (ECA). The synthesis process was conducted at different voltages (10, 40, and 60) V in 1 h and using electrophoresis deposition (EPD) in doping zeolite. The MZTC was covered with the array ordered, smooth and optimum elongated nanotubes with 5.1 μm of the length, 120.3 nm of the inner diameter 14.5 nm of the wall thickness with pure titanium and crystalline titania as determined by FESEM/EDS, and XRD. The kinetic study by following Langmuir-Hinshelwood(L-H) model and pseudo first order, the significant constant rate was obtained at pH 11 which was 0.079 ppm/min, 0.75 cm² of MZTC catalyst loading size achieved 0.076 ppm/min and 5 ppm of TCC initial concentration reached 0.162 ppm/min. The high-performance liquid chromatography (HPLC) analysis for mechanism study of TCC photocatalytic degradation revealed eleven intermediate products after the whole process of photocatalysis. In regard of toxicology assessment by the bacteria which is Photobacterium phosphoreum, the obtained concentration of TCC at minute 60 was less satisfied with remained 0.36 ppm of TCC was detected indicates that the concentration was above allowable level. Where the allowable level of TCC in stream is 0.1 ppm.

Nanomaterials for Photocatalytic Degradations of Analgesic, Mucolytic and Anti-Biotic/Viral/Inflammatory Drugs Widely Used in Controlling SARS-CoV-2

The COVID-19 pandemic has been transformed into one of the main worldwide challenges, in recent years. For controlling symptoms that are caused by this disease (e.g., chills or fever, shortness of breath and/or difficulty in breathing, cough, sore throat, fatigue, headache, muscle aches, the new loss of tastes and/or smells, congestion or runny nose, nausea, vomiting and/or diarrhea), lots of medicines including analgesics, mucolytics, and anti-biotic/viral/inflammatory drugs have been frequently prescribed. As these medicines finally contaminate terrestrial and aquatic habitats by entering surface waterways through pharmaceutical production and excreting trace amounts of waste after human usage, they have negative impacts on wildlife’s health and ecosystem. Residual drugs in water have the potential to harm aquatic creatures and disrupt their food chain as well as the breeding cycle. Therefore, proper degradation of these broadly used medicines is highly crucial. In this work, the use of nanomaterials applicable in photocatalytic degradations of analgesics (e.g., acetaminophen, aspirin, ibuprofen, and naproxen), mucolytics (e.g., ambroxol), antibiotics (e.g., azithromycin and quinolones including hydroxychloroquine and chloroquine phosphate), anti-inflammatory glucocorticoids (e.g., dexamethasone and cortisone acetate), antihistamines (e.g., diphenhydramine), H2 blockers (e.g., famotidine), anthelmintics (e.g., praziquantel), and finally antivirals (e.g., ivermectin, acyclovir, lopinavir/ritonavir, favipiravir, nitazoxanide, and remdesivir) which widely used in controlling/treating the coronavirus have been reviewed and discussed.

An organometallic approach for the preparation of Au-TiO2 and Au-g-C3N4 nanohybrids: improving the depletion of paracetamol under visible light

The photocatalytic degradation of paracetamol (a common analgesic also known as acetaminophen) in ultrapure water with different photocatalytic systems was performed under ultraviolet or visible irradiation. The photocatalysts employed were: commercial Degussa-P25 TiO₂ and Au-TiO₂ under UVA irradiation (365 nm) and g-C₃N₄ and Au-g-C₃N₄ under visible light irradiation (low-power (4 × 10 W) white light LEDs), improving the effectiveness of degradation rates when the gold nanoparticles (Au NPs) were combined with the semiconductors. The nanostructured photocatalysts were synthesised and characterised by transmission electron microscope (TEM), UV-vis diffuse reflectance spectroscopy and, in the case of g-C₃N₄ photocatalysts by X-ray photoelectron spectroscopy (XPS). The influence of the pH in the depletion of paracetamol with g-C₃N₄ and visible light was evaluated. In addition, the stability and lifetime of the photocatalyst g-C₃N₄ in the degradation of paracetamol were studied.

Nanoscale water spray assisted synthesis of CAs@B-TiO2core-shell nanospheres with enhanced visible-light photocatalytic activity

Increasing photoactive areas and oxygen vacancy to improve the separation and utilization of electrons and holes in a photocatalytic process are a guarantee for highly photocatalysis efficiency. In this work, we report a CAs@B-TiO₂core-shell nanospheres via a nanoscale water spray assisted method to deposit of black titanium dioxide (B-TiO₂) on carbon aerogel sphere (CAs) though slowly hydrolyzing of butyl titanate (e.g. TBOT) in an ethanol-water system. On this basis, furthermore, a facile one-step N₂H₄ · H₂O treatment was used to introduces oxygen vacancies on the surface of TiO₂coating layer forming black TiO₂. Oxygen vacancies can extend the optical response range of the TiO₂shell from the ultraviolet to the visible region, and increase conductivity and charge transport on the interface of core-shell structure. This study reveals the importance of surface oxygen vacancies for reducing band gaps and developing highly active photocatalysts under visible light.

Comparative Photo-Electrochemical and Photocatalytic Studies with Nanosized TiO2 Photocatalysts towards Organic Pollutants Oxidation

The size of TiO2 can significantly affect both its photocatalytic and photo-electrochemical properties, thus altering the photooxidation of organic pollutants in air or water. In this work, we give an account of the photo-electrochemical and photocatalytic features of some nanosized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulate electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the larger-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction. Finally, a direct correlation between the photocatalytic measurements in gas phase and the photo-electrochemical measurements in aqueous phase is given, thus evincing the important role of the substrate-surface interaction with similar acetone concentrations.

Design of Multifunctional Titania-Based Photocatalysts by Controlled Redox Reactions

This work aims at the preparation of multifunctional titania-based photocatalysts with inherent capabilities for thermal co-activation and stabilisation of anatase polymorph, by designing the phase composition and microstructure of rutile-silicon carbide mixture. The processing involved a conventional solid state route, including partial pre-reduction of rutile by SiC in inert Ar atmosphere, followed by post-oxidation in air. The impacts of processing conditions on the phase composition and photocatalytic activity were evaluated using Taguchi planning. The XRD studies confirmed the presence of rutile/anatase mixtures in the post-oxidised samples. The results emphasise that pre-reduction and post-oxidation temperatures are critical in defining the phase composition, while post-oxidation time is relevant for the photocatalytic performance. Microstructural studies revealed the formation of core-shell particles, which can suppress the photocatalytic activity. The highest apparent reaction rate of the photodegradation of methylene blue was observed for the sample pre-reduced in Ar at 1300 °C for 5 h and then calcined in air at 400 °C for 25 h. Though its performance was ~1.6-times lower than that for the same amount of nanostructured industrial P25 photocatalyst, it was achieved in the material possessing 2–3 times lower surface area and containing ~50 mol% of SiO₂ and SiC, thus demonstrating excellent prospects for further improvements.

Metabolic activity and pathway study of aspirin biodegradation using a microbial electrochemical system supplied by an alternating current

The main aim of this study is to investigate the biodegradation of highly concentrated aspirin as an emerging pollutant from aqueous solution using an alternating current microbial electrochemical system. A single-chamber Plexiglas cylindrical reactor equipped with stainless steel mesh electrodes (18 cm height × 16 cm diameter) was applied as the bioreactor in batch mode with an effective volume of 5 L, height of 20 cm, and the diameter about 20 cm by AMPL = 2 V_pp, OFST = 0.1 V, waveform = sinusoidal, frequency = 10 Hz, and pH = 7. The process parameters including initial concentration (100-400 mg L^-1), chemical oxygen demand (COD), activity of enzymes, biokinetic and pathway studies at very low voltage and very low frequency alternating current were investigated. The specific biodegradation rate of aspirin was calculated based on Michaelis-Menten model. The complete aspirin removal efficiency and the maximum enzymatic activity were achieved at 250 mg L^-1 aspirin, voltage of 2 V_pp and applied current = 3 mA during 6 h. The bioassay of aspirin concentrations in biofilm of the system using flow cytometry analysis resulted in the live and necrotic cells shares of 96.2%, and 0.44%, respectively. Moreover, the LC and GC-MS analysis showed low molecular weight acids such as oxalic and acetic acid at 6 h time under the optimal conditions using very low applied voltage and frequency. Obtaining low reaction time for degradation, high potential in biodegradation, oxidation and mineralization ability were the novelty of treatment system with high concentration aspirin in the study.

Micro-TiO2 coated glass surfaces safely abate drugs in surface water

The ingredients of Pharmaceuticals and Personal Care Products (PPCPs) persist in water and conventional treatment plants are not able to remove them efficiently. Sonochemical treatment is insufficient to mineralize organics such as ibuprofen into CO₂ and H₂O. TiO₂ degrades ibuprofen (IBP) under UV light; however, it does not reach a high grade of conversion. Here, we investigated the mineralization of ibuprofen to CO₂ by TiO₂ UV-C photocatalysis. We replaced nano-sized P25 (the standard catalyst) with a micro-sized commercial sample of TiO₂ to preclude the use of nanoparticles which are dangerous for human health and because typical filtration systems are expensive and inefficient. We deposited micro-TiO₂ on glass Raschig rings to ensure an easy recovery and reuse of the photocatalyst and we studied its performance both with a batch and a continuous reactor. Micro-TiO₂ mineralized 100% of IBP in 24 h. TiO₂-coated glass Raschig rings degraded 87% of IBP in 6 h of UV-C irradiation in a continuous reactor, with a mineralization of 25%. Electronspray ionization mass spectrometer (ESI-MS, positive mode) analyses identified 13 different byproducts and we hypothised a degradration pathway for IBP degradation.

Sub-lethal effects induced by a mixture of different pharmaceutical drugs in predicted environmentally relevant concentrations on Lithobates catesbeianus (Shaw, 1802) (Anura, ranidae) tadpoles

The increasing consumption of medications by humans has negative effects such as the increased disposal of these compounds in the environment. Little is known about how the disposal of a "drug mix" (DM) in aquatic ecosystems can affect their biota. Thus, we evaluated whether the exposure of Lithobates casteibeianus tadpoles to a DM composed of different medication classes (antibiotic, anti-inflammatory, antidepressant, anxiolytic, analgesic, and antacid drugs)-at environmentally relevant concentrations-may change their oral morphology, trigger behavioral disorders, and have mutagenic effects on erythrocyte cells. Based on our data, animals exposed to the DM showed changes in mandibular sheath pigmentation, dentition, and swimming activity, as well as atypical behavior in the social aggregation test [with co-specific and interspecific (Physalaemus cuvieri) individuals] and antipredatory defensive response deficit (chemical stimulus from Odonata larvae), after 15 exposure days. The mutagenic analysis revealed higher frequency of nuclear abnormalities in the erythrocytes of tadpoles exposed to the DM (e.g., multilobulated, blebbed, kidney-shaped, notched nucleus, binuclear, and micronucleated erythrocytes). Given the chemical complexity of the DM, we assumed that several organic functions may have been affected, either by the isolated, synergistic, antagonistic, or additive action of DM compounds. Finally, our study confirms the toxicological potential of DM in L. catesbeianus tadpoles, with emphasis to impacts that can affect the fitness of individuals and their natural populations. Thus, we suggest that more attention should be given to the disposal of medications in the environment and reinforce the need of improving water and sewage treatment systems.

Advanced oxidation process-mediated removal of pharmaceuticals from water: A review

Pharmaceuticals, which are frequently detected in natural and wastewater bodies as well as drinking water have attracted considerable attention, because they do not readily biodegrade and may persist and remain toxic. As a result, pharmaceutical residues pose on-going and potential health and environmental risks. To tackle these emerging contaminants, advanced oxidation processes (AOPs) such as photo-Fenton, sonolysis, electrochemical oxidation, radiation and ozonation etc. have been applied to remove pharmaceuticals. These processes utilize the high reactivity of hydroxyl radicals to progressively oxidize organic compounds to innocuous products. This review provides an overview of the findings from recent studies, which have applied AOPs to degrade pharmaceutical compounds. Included is a discussion that links various factors of TiO₂-mediated photocatalytic treatment to its effectiveness in degrading pharmaceutical residues. This review furthermore highlights the success of AOPs in the removal of pharmaceuticals from different water matrices and recommendations for future studies are outlined.

Micro-sized TiO2 as photoactive catalyst coated on industrial porcelain grès tiles to photodegrade drugs in water

Pharmaceutical compounds and their metabolites raise worrying questions because of their continuous release and lack of efficient removal by conventional wastewater treatments; therefore, they are being detected in groundwater, surface water and drinking water in increasing concentrations. Paracetamol and aspirin are two of the most commonly used drugs employed as fever reducer, analgesic and anti-inflammatory. They and their metabolites are very often found in river water, so their degradation is necessary in order to render water suitable for human consumption. The present work is focused on the comparison of the photocatalytic performance of industrial active grés porcelain tiles covered with a commercial micro-sized TiO₂ by industrial process using either conventional spray deposition or innovative digital printing methods. The photodegradation of two commonly used drugs, namely aspirin and paracetamol, was investigated both individually and as a mixture, in both deionized and tap water. The results reveal the full conversion of the drugs and the significant role of the photocatalytic tiles in the mineralization processes leading to harmless inorganic species. In particular, the digitally printed tiles exhibited better photodegradation performance for both drugs compared to the spray deposited tiles. No deactivation was observed on both photocatalytic tiles.

Degradation of acetaminophen in aqueous solution under visible light irradiation by Bi-modified titanate nanomaterials: morphology effect, kinetics and mechanism

Three morphologies of Bi-modified titanate nanomaterials were prepared using the hydrothermal method and controlled parameters to degrade acetaminophen.