Performance and emission analysis on blends of diesel, restaurant yellow grease and n-pentanol in direct-injection diesel engine

Mitigating carcinogenic smoke opacity in a light-duty diesel engine by utilizing cyclohexanol, polyethylene glycol, and 2-methoxyethanol

Diesel fuel reformulation is an attractive method to reduce hazardous smoke emissions because it does not require modifications to the existing engine infrastructure. As the concerns about global warming and air pollution are mounting, high-efficiency diesel engines with low smoke emissions have become more attractive. This study demonstrates that three alcohols, viz. cyclohexanol, polyethylene glycol, and 2-methoxyethanol, can be added to fossil diesel up to 3% by vol. to reduce carcinogenic smoke emissions in a one-cylinder, common rail direct injection (CRDI) diesel engine. The experimental investigations revealed that smoke could be reduced by up to 66.2%, 39.6% and 14% using 3% by vol. addition of cyclohexanol, polyethylene glycol, and 2-methoxyethanol to diesel, respectively, when compared to pure diesel operation. 1% addition by vol. of cyclohexanol and 2-methoxyethanol could reduce NOx and smoke emissions under all load conditions. CO emissions are slightly higher for all alcohol at high load conditions. HC emissions for the test fuels are lower than pure diesel operation at low load conditions, increasing at high loads. These emissions, however, can be reduced by using suitable after-treatment devices.

Study of the effects of bio-silica nanoparticle additives on the performance, combustion, and emission characteristics of biodiesel produced from waste fat

Numerous countries are investigating alternative fuel sources in response to the escalating issue of energy inadequacy. Using environmentally sustainable biodiesel as a potential alternative to fossil fuels, particularly from waste sources, is a developing prospect. This study aims to examine the feasibility of utilizing industry leather waste as a diesel fuel substitute. Traditional transesterification was used to obtain methyl ester out of leather waste. After processing, 81.93% of methyl ester was produced. Bio-silica (Bio-Si) is used as a fuel additive to enhance combustion and decrease emissions. This work utilized a leather industry waste fat biodiesel (LIWFB), LIWFB blend (B50), LIWFB blend with Bio-Si nanoparticles (B50Bio-Si50, B50Bio-Si75, and B50Bio-Si100 ppm) to analyze the engine outcome parameters at standard operating conditions. Experimental results revealed that adding Bio-Si in the biodiesel blend increased thermal brake efficiency (BTE) but was lower in diesel fuel. The biodiesel blends reduced NOx emissions more than Bio-Si nanoparticle blends. Furthermore, the smoke opacity was reduced by 31.87%, hydrocarbon (HC) emissions were reduced by 34.14%, carbon monoxide (CO) emissions were decreased by 43.97%, and oxides of nitrogen (NOx) emissions were slightly increased by 4.45% for B50Bio-Si100 blend compared to neat diesel. This investigation determined that all the emissions remained lower for all combinations than neat diesel, with a small increase in NOx emissions. Therefore, the LIWFB blend with Bio-Si nanoparticles was a viable diesel fuel alternative in diesel engines.

Experimental evaluation of soapberry seed oil biodiesel performance in CRDI diesel engine

Due to the ongoing demand for alternative fuels for CI engines, biodiesel-based research has received support globally. In this study, soapberry seed oil produced by transesterification process to creates biodiesel. It is referred to as BDSS (Biodiesel of Soapberry Seed). According to criteria, the oil qualities are recognized, hence, three different blends and pure diesel were tested in CRDI (Common Rail Direct Injection) engines. The blends descriptions are: 10BDSS (10% BDSS + 90% diesel), 20BDSS (20% BDSS + 80% diesel), and 30BDSS (30% BDSS + 70% diesel). The outcomes of the related tests for combustion, performance, and pollution were contrasted with those achieved using 100% diesel fuel. In this case, the mixing has resulted in worse braking thermal efficiency than diesel and lower residual emissions with greater NOx emissions. The superior results were obtained by 30BDSS, which had BTE of 27.82%, NOx emissions of 1348 ppm, peak pressure of 78.93 bar, heat release rate (HRR) of 61.15 J/deg, emissions of CO (0.81%), HC (11 ppm), and smoke opacity of 15.38%.

Influence of antioxidant additives on performance and emission characteristics of beef tallow biodiesel-fuelled C.I engine

This work analyses the performance and emission characteristics of biofuelled compression ignition (C.I) engine with the implementation of an antioxidant. Using the transesterification process with sodium hydroxide as a catalyst, the beef tallow methyl ester (BTME) was obtained from the beef tallow oil. Poor physical properties of biodiesel (beef tallow oil (BTO)) namely high viscosity and density cause atomization problems leading to higher smoke, hydrocarbon and carbon monoxide emissions. The purpose of this work is to enhance the performance aspects, to limit smoke emissions from BTO operation and to examine the possibility of direct use of neat BTO in CI engine. This research paves a way of investing the impact of binary blends of BHA and BTO on the research engine. The experiments were conducted on a single-cylinder four-stroke C.I engine using the following fuel compositions: 20% of BTME mixed with 80% diesel (B20), 1000 ppm mono-phenolic antioxidant (butylated hydroxyanisole (BHA)) mixed with the blends of B20 (B20 + BHA), and 100% diesel. Based on the experimental results, it was found that the brake thermal efficiency (BTE) increases by 1.8% and the brake specific fuel consumption (BSFC) decreases by 2.5% for the fuel blend B20 + BHA when compared with that for B20 fuel blend. Compared with the B20 blend, the blend B20 + BHA emits 12.2% lesser nitrogen oxide due to breaking chain reactions, scavenging the initiating radicals and reducing the concentration of reactive radicals.

A comprehensive study on emission and performance characteristics of a diesel engine fueled with nanoparticle-blended biodiesel

The present work is aimed to analyze the performance and emission characteristics of mahua biodiesel-fueled diesel engine with copper oxide nanoparticle at various particle sizes (10 and 20 nm) and the results compared with conventional diesel fuel (BD). Experiments were conducted in a four-stroke, single-cylinder, constant speed, and naturally aspirated research diesel engine with an eddy current dynamometer. Conventional transesterification process is carried out to convert the raw mahua oil into mahua oil biodiesel (BD100). Copper oxide (CuO) was chosen as a nanoparticle; the mass fraction of 100 ppm and the particle sizes of 10 and 20 nm were blended with mahua oil methyl ester using an ultrasonicator, and the physicochemical properties were measured. The physicochemical properties of BD100 and nanoparticle-included BD100 are at par with EN14214 limits. Brake-specific fuel consumption (BSFC) of BD100 is higher than that of diesel, and brake thermal efficiency (BTE) is lower than that of diesel (D100). The inclusion of 10-nm particle size of CuO nanoparticle in BD100 improves the BSFC and BTE by 1.3 and 0.7%, respectively, when compared with BD100. The CuO nanoparticle inclusion at 20-nm nanoparticle in biodiesel further improves the performance parameters than those at 10-nm nanoparticle. Further, the BD100 promotes a lower level of smoke emissions, carbon monoxide (CO), and hydrocarbon (HC) and with a prominent increase in oxides of nitrogen (NO_x) emissions. The inclusion of 10-nm particle size of CuO nanoparticle in BD100 reduces the NO_x, HC, CO, and smoke emission by 3.9, 5.6, 4.9, and 2.8%, respectively, at peak load condition when compared with BD100. The addition of CuO nanoparticle at 20-nm nanoparticle in biodiesel further reduces the NO_x, HC, CO, and smoke emissions.

Effect of lower and higher alcohol fuel synergies in biofuel blends and exhaust treatment system on emissions from CI engine

The present study deals with performance, emission and combustion studies in a single cylinder CI engine with lower and higher alcohol fuel synergies with biofuel blends and exhaust treatment system. Karanja oil methyl ester (KOME), widely available biofuel in India, and orange oil (ORG), a low carbon biofuel, were taken for this study, and equal volume blend was prepared for testing. Methanol (M) and n-pentanol (P) was taken as lower and higher alcohol and blended 20% by volume with KOME-ORG blend. Activated carbon-based exhaust treatment indigenous system was designed and tested with KOME-ORG + M20 and KOME-ORG + P20 blend. The tests were carried out at various load conditions at a constant speed of 1500 rpm. The study revealed that considering performance, emission and combustion studies, KOME-ORG + M20 + activated carbon are found optimum in reducing NO, smoke and CO₂ emission. Compared to KOME, for KOME-ORG + M20 + activated carbon, NO emission is reduced from 10.25 to 7.85 g/kWh, the smoke emission is reduced from 49.4 to 28.9%, and CO₂ emission is reduced from 1098.84 to 580.68 g/kWh. However, with exhaust treatment system, an increase in HC and CO emissions and reduced thermal efficiency is observed due to backpressure effects.