Influence of ambient temperature on the CO2 emitted of light-duty vehicle

Because of global warming, people have paid more attention to greenhouse gas emitted by vehicles. To quantify the impact of temperature on vehicle CO2 emissions, this study was conducted using the world light vehicle test cycle on two light-duty E10 gasoline vehicles at ambient temperatures of -10, 0, 23, and 40℃, and found that CO2 emission factors of Vehicle 1 in the low-speed phase were 22.07% and 20.22% higher than those of Vehicle 2 at cold start and hot start under -10℃. The reason was vehicle 1 had a larger displacement and more friction pairs than vehicle 2. There was the highest CO2 emission at the low-speed phase due to low average speed, frequent acceleration, and deceleration. The CO2 temperature factor and the ambient temperature had a strong linear correlation (R2 = 0.99). According to CO2 temperature factors and their relationships, CO2 emission factors of other ambient temperatures could be calculated when the CO2 emission factor of 23℃ was obtained, and the method also could be used to obtain the CO2 temperature factors of different vehicles. To separate the effect of load setting and temperature variation on CO2 emission quantitatively, a method was proposed. And results showed that the load setting was dominant for the CO2 emission variation. Compared with 23℃, the CO2 emission for vehicle 1 caused by load setting variation were 62.83 and 47.42 g/km, respectively at -10 and 0℃, while those for vehicle 2 were 45.01 and 35.63 g/km, respectively.

Impacts of ethanol blended fuels and cold temperature on VOC emissions from gasoline vehicles in China

The Chinese central government has initiated pilot projects to promote the adoption of gasoline containing 10%v ethanol (E10). Vehicle emissions using ethanol blended fuels require investigation to estimate the environmental impacts of the initiative. Five fuel formulations were created using two blending methods (splash blending and match blending) to evaluate the impacts of formulations on speciated volatile organic compounds (VOCs) from exhaust emissions. Seven in-use vehicles covering China 4 to China 6 emission standards were recruited. Vehicle tests were conducted using the Worldwide Harmonized Test Cycle (WLTC) in a temperature-controlled chamber at 23 °C and -7 °C. Splash blended E10 fuels led to significant reductions in VOC emissions by 12%-75%. E10 fuels had a better performance of reducing VOC emissions in older model vehicles than in newer model vehicles. These results suggested that E10 fuel could be an option to mitigate the VOC emissions. Although replacing methyl tert-butyl ether (MTBE) with ethanol in regular gasoline had no significant effects on VOC emissions, the replacement led to lower aromatic emissions by 40%-60%. Alkanes and aromatics dominated approximately 90% of VOC emissions for all vehicle-fuel combinations. Cold temperature increased VOC emissions significantly, by 3-26 folds for all vehicle/fuel combinations at -7 °C. Aromatic emissions were increased by cold temperature, from 2 to 26 mg/km at 23 °C to 33-238 mg/km at -7 °C. OVOC emissions were not significantly affected by E10 fuel or cold temperature. The ozone formation potential (OFP) and secondary organic aerosol formation potential (SOAFP) of splash blended E10 fuels decreased by up to 76% and 81%, respectively, compared with those of E0 fuels. The results are useful to update VOC emission profiles of Chinese vehicles using ethanol blended gasoline and under low-temperature conditions.

Electrification of Transit Buses in the United States Reduces Greenhouse Gas Emissions

The transportation sector is the largest emitter of greenhouse gas emissions (GHGs) in the United States. Increased use of public transit and electrification of public transit could help reduce these emissions. The electrification of public transit systems could also reduce air pollutant emissions in densely populated areas, where air pollution disproportionally burdens vulnerable communities with high health impacts and associated social costs. We analyze the life cycle emissions of transit buses powered by electricity, diesel, gasoline, and compressed natural gas and model GHGs and air pollutants mitigated for a transition to a fully electric U.S. public transit bus fleet using transit agency-level data. The electrification of the U.S. bus fleet would reduce several conventional air pollutants and has the potential to reduce transit bus GHGs by 33-65% within the next 14 years depending on how quickly the transition is made and how quickly the electricity grid decarbonizes. A levelized cost of driving analysis shows that with falling capital costs and an increase in annual passenger-kilometers of battery electric buses, the technology could reach levelized cost parity with diesel buses when electric bus capital costs fall below about $670 000 per bus.

Emission performance evaluation of urban passenger car fleet through field investigation data in a megacity

Continued improvements in living standards and the economic well-being in the megacities have led to a huge surge in vehicular density. The worst environmental outcome of the same has been persistent unsafe urban air quality, thanks to vehicular emission. Further, the existing inspection and maintenance programs, conceived to check such emission remain largely ineffective, particularly in developing countries. This is due to the absence of a thorough assessment of the vehicle's compliance with the in-use emission norms generated through reliable field investigation data. To address this gap, the present comprehensive study collected real-time tailpipe emission data from 2040 cars in Delhi, India. Exhaust emission parameters, namely, CO (carbon monoxide), HC (hydrocarbon), and SE (smoke emission), were recorded from both petrol and diesel-driven cars of private ownership, in collaboration with the emission compliance test centers. The performance of cars was assessed in terms of their compliance with the in-use BS (Bharat Stage) emission norms. The one-of-its-kind study reported the petrol cars to be highly compliant toward the BS IV norm while faring even better toward BS II for both CO and HC emissions (80-90%). The conformance to the HC norm was found to be typically better than that for CO (85-90% versus 75-80%). For the diesel-driven cars, BS III compliance levels were reported relatively better compared to BS IV (90% in the case of the former against 80% in the latter's case). Further, the study puts forward a clear indication that the in-use emission norm and maintenance status of cars have a direct and negative relationship with tailpipe emission parameters. Cars of both overseas and domestic origin have almost equal degrees of compliance with the emission norms (over 80% in any case). The study recommends the incorporation of these two critical vehicular variables, i.e., maintenance status and in-use emission standard in the emission certification policy.

An integrated approach for wastewater treatment and algae cultivation: Nutrient removal analysis, biodiesel extraction, and energy and environmental metrics enhancement

Human urine is rich in nitrogen and phosphorus, and the presence of these elements in wastewater significantly disrupts the biogeochemical cycle. Meanwhile, green algal biomass cultivation is unfeasible without these nutrients. Hence, the present study integrates wastewater treatment and algae cultivation to extract biodiesel and improve its performance through fuel modification. Chlorella vulgaris algae was cultivated in different dilution ratios of water and urine, and the nutrient removal rate was analyzed. Chlorella vulgaris algae biodiesel (CAB) was derived through Bligh and Dyer's method followed by transesterification, and its functional and elemental groups were analyzed. The various volume concentrations of CAB were blended with regular diesel fuel (RDF), and 10% water was added to a 30% CAB blended RDF to evaluate the combustion performance and environmental impacts. The results of the experiments demonstrated that the algae cultivation effectively removed the wastewater nutrients. The functional and elemental groups of CAB are identical to those of RDF. The engine characteristics of test fuels report that the CAB-blend RDF fuel mixtures generate low carbon footprints, whereas negative impacts have been drawn for performance metrics and oxides of nitrogen emissions. The water-emulsified fuel outweighed the unfavorable effects and promoted more efficient and cleaner combustion.

Hydrocarbon adsorption mechanism of modern automobile engines and methods of reducing hydrocarbon emissions during cold start process: A review

With the global emphasis on environmental protection and increasingly stringent emission regulations for internal combustion engines, there is an urgent need to overcome the problem of large hydrocarbon (HC) emissions caused by unstable engine cold starts. Synergistic engine pre-treatment (reducing hydrocarbon production) as well as after-treatment devices (adsorbing and oxidizing hydrocarbons) is the fundamental solution to emissions. In this paper, the improvement of hydrocarbon emissions is summarized from two aspects: pre-treatment and after-treatment. The pre-treatment for engine cold start mainly focuses on summarizing the intake control, fuel, and engine timing parameters. The after-treatment mainly focuses on summarizing different types of adsorbents and modifications (mainly including different molecular sieve structures and sizes, preparation conditions, silicon aluminum ratio, ion exchange modification, and heterogeneity, etc.), adsorptive catalysts (mainly including optimization of catalytic performance and structure), and catalytic devices (mainly including coupling with thermal management equipment and HC trap devices). In this paper, a SWOT (strength, weakness, opportunity, and threat) analysis of pre-treatment and after-treatment measures is conducted. Researchers can obtain relevant research results and seek new research directions and approaches for controlling cold start HC emissions.

Cleaning up while Changing Gears: The Role of Battery Design, Fossil Fuel Power Plants, and Vehicle Policy for Reducing Emissions in the Transition to Electric Vehicles

Plug-in electric vehicles (PEVs) can reduce air emissions when charged with clean power, but prior work estimated that in 2010, PEVs produced 2 to 3 times the consequential air emission externalities of gasoline vehicles in PJM (the largest US regional transmission operator, serving 65 million people) due largely to increased generation from coal-fired power plants to charge the vehicles. We investigate how this situation has changed since 2010, where we are now, and what the largest levers are for reducing PEV consequential life cycle emission externalities in the near future. We estimate that PEV emission externalities have dropped by 17% to 18% in PJM as natural gas replaced coal, but they will remain comparable to gasoline vehicle externalities in base case trajectories through at least 2035. Increased wind and solar power capacity is critical to achieving deep decarbonization in the long run, but through 2035 we estimate that it will primarily shift which fossil generators operate on the margin at times when PEVs charge and can even increase consequential PEV charging emissions in the near term. We find that the largest levers for reducing PEV emissions over the next decade are (1) shifting away from nickel-based batteries to lithium iron phosphate, (2) reducing emissions from fossil generators, and (3) revising vehicle fleet emission standards. While our numerical estimates are regionally specific, key findings apply to most power systems today, in which renewable generators typically produce as much output as possible, regardless of the load, while dispatchable fossil fuel generators respond to the changes in load.

Cow-urine emulsified diesel fuel: preparation, stability, and rheological study for diesel engine application

Water-diesel emulsion fuel has been found as a prominent alternative fuel by various researchers. Alike this technology, cow-urine (Bos indicus urine) emulsified diesel fuel (GMD emulsion) has been explored in this study. Making of homogeneous and stable emulsion is a crucial aspect in this approach while maintaining the diesel standards. Hence, the applicability of this fuel has been examined based on physicochemical properties for diesel engine application. The stability was assessed by creaming index, droplet size, Pdi, and interfacial tension. The minimum droplet size (278 nm) and 0.282 Pdi was obtained with 5.72 HLB value, 4% (v/v) surfactant, and 10% (v/v) of cow-urine through ultra-sonication. The optimized 10% GMD emulsion was found stable for more than 80 days. Viscosity and density of the fuel got increased with cow-urine and surfactant; however, they found within the standard limits. The physicochemical analysis exhibited the feasibility of the GMD emulsion for diesel engine application.

Comparing different methods for olefin quantification in pygas and plastic pyrolysis oils: Gas chromatography-vacuum ultraviolet detection versus comprehensive gas chromatography versus bromine number titration

In steam cracking, upstream pyrolysis oil hydroprocessing, and in many downstream processes, olefinic content is key to assess process performance and process safety risk associated with highly exothermic reactions. When looking to plastic pyrolysis oils as a potential feedstock, as well as downstream products such as pyrolysis gasoline (pygas), these materials contain unsaturated hydrocarbons which are not present in fossil feedstocks. Pygas is a product of pyrolysis and exhibits a large number of chemical structural similarities with plastic pyrolysis oils, especially in terms of olefins structure. Quantification of the unsaturation content (olefins and di-olefins) is extremely important in industry, hence the focus of this manuscript. Detailed hydrocarbon analysis with flame ionization detection is inadequate to fully characterize the hydrocarbon composition of such samples, especially when peaks are closely eluting, or even co-eluting. In this study, the gas chromatography coupled to vacuum ultraviolet (GC-VUV) detection method previously described for the analysis of liquid hydrocarbon streams1 and plastic pyrolysis oils2 has been compared with comprehensive gas chromatography (GC × GC) and the industry standard for olefin quantification (i.e., bromine number titration). Although based on different methodologies, a correlation between the olefin content obtained from GC-VUV and the bromine number titration method is hereby presented.

Will changes in charging and gasoline prices affect electric vehicle sales? Evidence from China

Electric vehicles and gasoline vehicles are substitutes for each other, and the cost of fuel is an important factor when consumers are faced with choices. Understanding the influence of changes in gasoline prices and charging prices on electric vehicle sales is of reference significance for promoting electric vehicles in the private sector. This paper uses data covering 212 prefecture-level cities from January, 2020, to August, 2022, for analysis, and the results show that different income groups have different sensitivities to the difference in oil and electricity prices. Additionally, changes in gasoline prices and charging prices will significantly affect electric vehicle sales in low-income and middle-income cities, electric vehicle sales in high-income cities will not be affected. Compared with nonpilot cities, residents of pilot cities are more sensitive to fuel price changes, indicating that the policy basis has a certain positive effect on the promotion of electric vehicles. It is recommended to consider the income status of regional residents when formulating policies for the use of electric vehicles. At the same time, publicity efforts should be increased to highlight the gap between the cost of fuel vehicles and electric vehicles.

Sex-specific metabolic adaptations from in utero exposure to particulate matter derived from combustion of petrodiesel and biodiesel fuels

Maternal exposure to particulate matter derived from diesel exhaust has been shown to cause metabolic dysregulation, neurological problems, and increased susceptibility to diabetes in the offspring. Diesel exhaust is a major source of air pollution and the use of biodiesel (BD) and its blends have been progressively increasing throughout the world; however, studies on the health impact of BD vs. petrodiesel combustion-generated exhaust have been controversial in part, due to differences in the chemical and physical nature of the associated particulate matter (PM). To explore the long-term impact of prenatal exposure, pregnant mice were exposed to PM generated by combustion of petrodiesel (B0) and a 20% soy BD blend (B20) by intratracheal instillation during embryonic days 9-17 and allowed to deliver. Offspring were then followed for 52 weeks. We found that mother's exposure to B0 and B20 PM manifested in striking sex-specific phenotypes with respect to metabolic adaptation, maintenance of glucose homeostasis, and medial hypothalamic glial cell makeup in the offspring. The data suggest PM exposure limited to a narrower critical developmental window may be compensated for by the mother and/or the fetus by altered metabolic programming in a marked sex-specific and fuel-derived PM-specific manner, leading to sex-specific risk for diseases related to environmental exposure later in life.

Instantaneous CO2 emission modelling for a Euro 6 start-stop vehicle based on portable emission measurement system data and artificial intelligence methods

One of the increasingly common methods to counteract the increased fuel consumption of vehicles is start-stop technology. This paper introduces a methodology which presents the process of measuring and creating a computational model of CO2 emissions using artificial intelligence techniques for a vehicle equipped with start-stop technology. The method requires only measurement data of velocity, acceleration of vehicle, and gradient of road to predict the emission of CO2. In this paper, three methods of machine learning techniques were analyzed, while the best prediction results are shown by the gradient boosting method. For the developed models, the results were validated using the coefficient of determination, the mean squared error, and based on visual evaluation of residual and instantaneous emission plots and CO2 emission maps. The developed models present a novel methodology and can be used for microscale environmental analysis.

Novel insights into the NOx emissions characteristics in PEMS tests of a heavy-duty vehicle under different payloads

Real Drive Emission (RDE) test with Portable Emission Measurement System (PEMS) is a widely adopted way to assess vehicle emission compliance. However, the current NOx emissions calculation method stipulated in the China VI emission standard easily ignores the NOx emissions during cold start and low-power operation. To study the effect of cold start and low-power operation on the calculation of NOx emissions in the PEMS test, in this study, a China VI Heavy-Duty Vehicle (HDV) for urban use was used to conduct PEMS tests under various vehicle payload conditions. The data analysis results show that the increase in vehicle payload is beneficial to reducing the specific NOx emissions and passing the NOx emission compliance test because the increased payload improves the NOx conversion efficiency of the SCR system. Cold start duration has no obvious relationship with vehicle payload, accounting for only about 4∼6% in each test, but contributing more than 30% of NOx emissions. Due to the effect of the power threshold and the 90th cumulative percentile, the cold start data has little influence on the result of the NOx emissions assessment and the maximum variation of the NOx emissions result in this study is an 8% rise. For the HDV for urban use, the variation of the power threshold resulting from vehicle payload is small, no more than 2% in this study. The presence of the power threshold makes almost only the low-power operation in the second half of urban driving have an impact on the NOx emissions calculation, which may make more than 50% of NOx emissions in the PEMS test be neglected. The impact of the low-power operation on NOx emissions calculation result will be significantly enhanced if all windows are considered in the Moving Average Window (MAW) method. In the meantime, the degree of variation is closely related to the NOx emissions level during the first half of urban driving. The maximum deterioration of NOx emission assessment result can be more than 90% in this study.

Improved Spatial Resolution in Modeling of Nitrogen Oxide Concentrations in the Los Angeles Basin

The extent to which emission control technologies and policies have reduced anthropogenic NOx emissions from motor vehicles is large but uncertain. We evaluate a fuel-based emission inventory for southern California during the June 2021 period, coinciding with the Re-Evaluating the Chemistry of Air Pollutants in CAlifornia (RECAP-CA) field campaign. A modified version of the Fuel-based Inventory of Vehicle Emissions (FIVE) is presented, incorporating 1.3 km resolution gridding and a new light-/medium-duty diesel vehicle category. NOx concentrations and weekday-weekend differences were predicted using the WRF-Chem model and evaluated using satellite and aircraft observations. Model performance was similar on weekdays and weekends, indicating appropriate day-of-week scaling of NOx emissions and a reasonable distribution of emissions by sector. Large observed weekend decreases in NOx are mainly due to changes in on-road vehicle emissions. The inventory presented in this study suggests that on-road vehicles were responsible for 55-72% of the NOx emissions in the South Coast Air Basin, compared to the corresponding fraction (43%) in the planning inventory from the South Coast Air Quality Management District. This fuel-based inventory suggests on-road NOx emissions that are 1.5 ± 0.4, 2.8 ± 0.6, and 1.3 ± 0.7 times the reference EMFAC model estimates for on-road gasoline, light- and medium-duty diesel, and heavy-duty diesel, respectively.

Characterization of Biodiesel and Diesel Combustion Particles: Chemical Composition, Lipid Metabolism, and Implications for Health and Environment

Biodiesel, derived from alkyl esters of vegetable oils or animal fats, has gained prominence as a greener alternative to diesel due to its reduced particle mass. However, it remains debatable whether biodiesel exposure has more severe health issues than diesel. This study performed high-resolution mass spectrometry to examine the detailed particle chemical compositions and lipidomics analysis of human lung epithelial cells treated with emissions from biodiesel and diesel fuels. Results show the presence of the peak substances of CHO compounds in biodiesel combustion that contain a phthalate ester (PAEs) structure (e.g., n-amyl isoamyl phthalate and diisobutyl phthalate). PAEs have emerged as persistent organic pollutants across various environmental media and are known to possess endocrine-disrupting properties in the environment. We further observed that biodiesel prevents triglyceride storage compared to diesel and inhibits triglycerides from becoming phospholipids, particularly with increased phosphatidylglycerols (PGs) and phosphatidylethanolamines (PEs), which potentially could lead to a higher probability of cancer metastasis.

Exceedances of Secondary Aerosol Formation from In-Use Natural Gas Heavy-Duty Vehicles Compared to Diesel Heavy-Duty Vehicles

This work, for the first time, assessed the secondary aerosol formation from both in-use diesel and natural gas heavy-duty vehicles of different vocations when they were operated on a chassis dynamometer while the vehicles were exercised on different driving cycles. Testing was performed on natural gas vehicles equipped with three-way catalysts (TWCs) and diesel trucks equipped with diesel oxidation catalysts, diesel particulate filters, and selective catalytic reduction systems. Secondary aerosol was measured after introducing dilute exhaust into a 30 m3 environmental chamber. Particulate matter ranged from 0.18 to 0.53 mg/mile for the diesel vehicles vs 1.4-85 mg/mile for the natural gas vehicles, total particle number ranged from 4.01 × 1012 to 3.61 × 1013 for the diesel vehicles vs 5.68 × 1012-2.75 × 1015 for the natural gas vehicles, and nonmethane organic gas emissions ranged from 0.032 to 0.05 mg/mile for the diesel vehicles vs 0.012-1.35 mg/mile for the natural gas vehicles. Ammonia formation was favored in the TWC and was found in higher concentrations for the natural gas vehicles (ranged from ∼0 to 1.75 g/mile) than diesel vehicles (ranged from ∼0 to 0.4 g/mile), leading to substantial secondary ammonium nitrate formation (ranging from 8.5 to 98.8 mg/mile for the natural gas vehicles). For the diesel vehicles, one had a secondary ammonium nitrate of 18.5 mg/mile, while the other showed essentially no secondary ammonium nitrate formation. The advanced aftertreatment controls in diesel vehicles resulted in almost negligible secondary organic aerosol (SOA) formation (ranging from 0.046 to 2.04 mg/mile), while the natural gas vehicles led to elevated SOA formation that was likely sourced from the engine lubricating oil (ranging from 3.11 to 39.7 mg/mile). For two natural gas vehicles, the contribution of lightly oxidized lubricating oil in the primary organic aerosol was dominant (as shown in the mass spectra analysis), leading to enhanced SOA mass. Heavily oxidized lubricating oil was also observed to contribute to the SOA formation for other natural gas vehicles.

The impact on passenger car emissions associated with the promotion and demise of diesel fuel

The promotion and growth in the use of diesel fuel in passenger cars in the UK and Europe over the past two decades led to considerable adverse air quality impacts in urban areas and more widely. In this work, we construct a multi-decade analysis of passenger car emissions in the UK based on real driving emissions data. An important part of the study is the use of extensive vehicle emission remote sensing data covering multiple measurement locations, time periods, environmental conditions and consisting of over 600,000 measurements. These data are used to consider two scenarios: first, that diesel fuel use was not promoted in the early 2000s for climate mitigation reasons, and second, that there was not a dramatic decline in diesel fuel use following the Dieselgate scandal. The strong growth of diesel fuel use coincided with a time when diesel NOx emissions were high and, conversely, the strong decrease of diesel fuel use coincided with a time when diesel vehicle after-treatment systems for NOx control were effective. We estimate that the growth in diesel car use in the UK results in excess NOx emissions of 721 kt over a three decade period; equivalent to over 7 times total annual passenger car NOx emissions and greater than total UK NOx emissions of 681.8 kt in 2021 and with an associated damage cost of £5.875 billion. However, the sharp move away from diesel fuel post-Dieselgate only reduced NOx emissions by 41 kt owing to the effectiveness of modern diesel aftertreatment systems.

Developing a carbon footprint model and environmental impact analysis of municipal solid waste transportation: A case study of Tehran, Iran

The greenhouse gas emitted due to transportation is the third greatest emitter globally, and its impact has become a threat to the environment, public health, and economic development. Waste transportation is excluded in studies of waste management despite its significant environmental impacts such as global warming and human toxicity. The objective of this study is to develop a quantification model to estimate the carbon footprint of waste transportation and environmental impact assessments in three categories applied in Tehran using IPCC guidelines. In Tehran, light and heavy vehicles ran on diesel fuel. Data on fuel and waste characteristics were provided by Tehran's department of transportation and municipality, respectively. In this study, transport-related emissions are 8.47 k tonCO2eq/y, and the carbon footprint of waste transportation is 93.57 g of CO2 eq per ton of waste transported (t.km), which is relevant to three main parameters: the amount of waste transported annually, the freight shipped from the temporary station to the disposal landfill site, and fossil fuels consumed. Also, an environmental impact assessment in three categories - human health (global warming, abiotic depletion, and ozone layer depletion), resources (fossil fuels), and ecosystem quality (acidification and eutrophication) - using SimaPro, a Life Cycle Assessment (LCA) tool is presented. Global warming (3.49 kg CO2 eq/t MSW), human toxicity (0.95 kg 1,4-DB eq/t MSW), and freshwater aquatic eco-toxicity (0.04 kg 1,4-DB eq/t MSW) have the greatest impact among categories. Sensitivity analysis of the effective parameters allows us to conclude one of the potential implications of this study would be the introduction of natural gas or biogas-based trucks replacing diesel fuel vehicles to improve air quality and mitigate the greenhouse gas emission.Implications: This paper addresses the significant issue of global warming, particularly in Iran, a developing country that ranks among the top contributors to greenhouse gas emissions. The study emphasizes the importance of evaluating emissions across various sectors such as electricity, waste, etc., Specifically, in this paper we focus on developing a model to quantify the environmental impact resulting from the combustion of fossil fuels in vehicles, focus on the metropolitan city of Tehran as a case study. By examining the waste transportation process, we aim to provide decision-makers with effective strategies to mitigate the environmental consequences. In this paper, we develop a simple quantification term of Carbon Footprint to calculate total greenhouse gas emission of waste transportation process. Carbon Footprint is a fraction which, its numerator is total greenhouse gas emission and its denominator is total waste transported in traveled distance. Effective parameters have been investigated and based on parameters and emission factors taken out of IPPC, the carbon footprint model have been developed. The total greenhouse gas emission of this study and the carbon footprint has estimated at 8.47 k tonCO2eq/y and 93.57 g CO2eq/t.km respectively. Furthermore, the paper explores additional environmental impacts beyond global warming, including abiotic depletion, ozone layer depletion, acidification, eutrophication, human toxicity, photochemical oxidation, and freshwater aquatic eco-toxicity. Using SimaPro software these eight impact categories have been estimated. in this study we identify fossil fuel consumption, traveled distance, and mass transported are the primary parameters influencing greenhouse gas emissions and the carbon footprint. To reduce emissions in the waste transportation system, we suggest promoting renewable biofuels, highlighting Iran as a suitable candidate due to its high percentage of biodegradable material in municipal solid waste. Additionally, the study assesses nonrenewable energy and mineral extraction using the IMPACT 2002+ V2.15/IMPACT 2002+ method, revealing that global warming (100 years), human toxicity (100 years), freshwater aquatic eco-toxicity, nonrenewable energy, and mineral extraction have the most significant impacts on the municipal solid waste transportation system. Overall, this research underscores the need for quantifying environmental impacts and recommends strategies to mitigate them in waste transportation processes, particularly in developing countries like Iran.

Exhaust particle number and composition for diesel and gasoline passenger cars under transient driving conditions: Real-world emissions down to 1.5 nm

Recent recommendations given by WHO include systematic measurements of ambient particle number concentration and black carbon (BC) concentrations. In India and several other highly polluted areas, the air quality problems are severe and the need for air quality related information is urgent. This study focuses on particle number emissions and BC emissions of passenger cars that are technologically relevant from an Indian perspective. Particle number and BC were investigated under real-world conditions for driving cycles typical for Indian urban environments. Two mobile laboratories and advanced aerosol and trace gas instrumentation were utilized. Our study shows that passenger cars without exhaust particle filtration can emit in real-world conditions large number of particles, and especially at deceleration a significant fraction of particle number can be even in 1.5-10 nm particle sizes. The mass concentration of exhaust plume particles was dominated by BC that was emitted especially at acceleration conditions. However, exhaust particles contained also organic compounds, indicating the roles of engine oil and fuel in exhaust particle formation. In general, our study was motivated by serious Indian air quality problems, by the recognized lack of emission information related to Indian traffic, and by the recent WHO air quality guidance; our results emphasize the importance of monitoring particle number concentrations and BC also in Indian urban areas and especially in traffic environments where people can be significantly exposed to fresh exhaust emissions.

Mitigating carcinogenic smoke opacity in a light-duty diesel engine by utilizing cyclohexanol, polyethylene glycol, and 2-methoxyethanol

Diesel fuel reformulation is an attractive method to reduce hazardous smoke emissions because it does not require modifications to the existing engine infrastructure. As the concerns about global warming and air pollution are mounting, high-efficiency diesel engines with low smoke emissions have become more attractive. This study demonstrates that three alcohols, viz. cyclohexanol, polyethylene glycol, and 2-methoxyethanol, can be added to fossil diesel up to 3% by vol. to reduce carcinogenic smoke emissions in a one-cylinder, common rail direct injection (CRDI) diesel engine. The experimental investigations revealed that smoke could be reduced by up to 66.2%, 39.6% and 14% using 3% by vol. addition of cyclohexanol, polyethylene glycol, and 2-methoxyethanol to diesel, respectively, when compared to pure diesel operation. 1% addition by vol. of cyclohexanol and 2-methoxyethanol could reduce NOx and smoke emissions under all load conditions. CO emissions are slightly higher for all alcohol at high load conditions. HC emissions for the test fuels are lower than pure diesel operation at low load conditions, increasing at high loads. These emissions, however, can be reduced by using suitable after-treatment devices.

Abatement of photochemical smog precursors through complete hydrocarbon oxidation over commercial Pd catalysts under fuel-lean conditions with NO promoting effect

Currently, severe environmental issues have led to a great transition in the automotive industry from internal combustion engine vehicles to electric vehicles, but this transition will take time more than 10 years, which still requires the use of internal combustion engine vehicles. However, these vehicles emit a significant amount of hydrocarbons, in addition to nitrogen oxides (NOx), due to incomplete fuel combustion. They contribute to the formation of photochemical smog when they react with NOx in the presence of sunlight. To effectively remove these hydrocarbons from the exhaust gas of turbo-gasoline engines or diesel engines, we investigated the abatement of propane and iso-pentane, two typical hydrocarbons. In particular, we studied commercial Pd catalysts and revealed how the Pd loading and aging process simulating 4k and 100k mileage affected hydrocarbon abatement abilities, and their phases were identified using characterization technique, including CO chemisorption, X-ray diffraction (XRD), and high-resolution transmission electron microscopy (HR-TEM). We also suggested the reaction pathway for the complete oxidation of propane over Pd catalyst based on the reaction orders of propane and oxygen: Propane adsorbs on O atoms of PdO, and the kinetically relevant C-H bond cleavage step occurs by the interaction with abundant neighboring O atoms of PdO. Finally, the propane and iso-pentane abatement ability of the Pd catalyst aged for 100k mileage were evaluated under realistic exhaust gas conditions, and the effect of each gas component in the realistic exhaust gas was identified; water inhibits the catalytic reaction of hydrocarbons by occupying the active sites, whereas NO catalyzes the hydrocarbon oxidation reaction by either changing the reaction pathway or active sites under fuel-lean conditions. These findings enable us to effectively reduce environmental pollution and facilitate a smoother transition from internal combustion engine vehicles to electric vehicles.

Should Transportation Be Transitioned to Ethanol with Carbon Capture and Pipelines or Electricity? A Case Study

An important issue today is whether gasoline vehicles should be replaced by flex-fuel vehicles (FFVs) that use ethanol-gasoline blends (e.g., E85), where some carbon dioxide (CO2) from ethanol's production is captured and piped, or battery-electric vehicles (BEVs) powered by wind or solar. This paper compares the options in a case study. It evaluates a proposal to capture fermentation CO2 from 34 ethanol refineries in 5 U.S. states and build an elaborate pipeline to transport the CO2 to an underground storage site. This "ethanol plan" is compared with building wind farms at the same cost to provide electricity for BEVs ("wind plan A"). Compared with the ethanol plan, wind plan A may reduce 2.4-4 times the CO2, save drivers in the five states $40-$66 billion (USD 2023) over 30 years even when BEVs initially cost $21,700 more than FFVs, require 1/400,000th the land footprint and 1/10th-1/20th the spacing area, and decrease air pollution. Even building wind to replace coal ("wind plan B") may avoid 1.5-2.5 times the CO2 as the ethanol plan. Thus, ethanol with carbon capture appears to be an opportunity cost that may damage climate and air quality, occupy land, and saddle consumers with high fuel costs for decades.

Direct identification of total and missing OH reactivities from light-duty gasoline vehicle exhaust in China based on LP-LIF measurement

Considerable efforts have been devoted to characterising the chemical components of vehicle exhaust. However, these components may not accurately reflect the contribution of vehicle exhaust to atmospheric reactivity because of the presence of species not accounted for ("missing species") given the limitations of analytical instruments. In this study, we improved the laser photolysis-laser-induced fluorescence (LP-LIF) technique and applied it to directly measure the total OH reactivity (TOR) in exhaust gas from light-duty gasoline vehicles in China. The TOR for China I to VI-a vehicles was 15.6, 16.3, 8.4, 2.6, 1.5, and 1.6 × 10⁴ sec^-1, respectively, reflecting a notable drop as emission standards were upgraded. The TOR was comparable between cold and warm starts. The missing OH reactivity (MOR) values for China I to IV vehicles were close to zero with a cold start but were much higher with a warm start. The variations in oxygenated volatile organic compounds (OVOCs) under different emission standards and for the two start conditions were similar to those of the MOR, indicating that OVOCs and the missing species may have similar production processes. Online measurement revealed that the duration of the stable driving stage was the primary factor leading to the production of OVOCs and missing species. Our findings underscore the importance of direct measurement of TOR from vehicle exhaust and highlight the necessity of adding OVOCs and other organic reactive gases in future upgrades of emission standards, such that the vehicular contribution to atmospheric reactivity can be more effectively controlled.

China 6 EGR gasoline vehicles without a GPF may struggle to meet the potential SPN10 limit

Particles larger than 10 nm from engine exhaust are gaining global concerns. In light of this, to investigate how EGR affects gasoline vehicle SPN10 (solid particles larger than 10 nm) emissions, seven gasoline vehicles (hybrid or conventional) were studied experimentally. The results revealed that EGR vehicles risk failing the current limit (6 * 1011 #/km) more than those without EGR if the cut-off size was tightened from 23 nm to 10 nm. More specifically, during the WLTC test, EGR increased the SPN10 emission factors by 2 ∼ 3 times depending on vehicle powertrains (conventional or hybrid). Notably, SPN10 emissions increased significantly when EGR was actively engaged but showed a decrease when the EGR rate remained constant. EGR and the enriched fuel-air mixture are the critical reasons for the increased SPN10.

Reduction of life-cycle CO2 emissions by expanding car-sharing services: A case study on Japan

Carbon neutrality is a growing concern for all global economies. We considered the number of new and used cars registered during 2009-2018 in Japan and estimated the total number of private and shared cars, assuming that when owners abandoned their old cars, a certain percentage of the owners chose to use a car-sharing service (i.e., car rental service), instead of buying a new private car. We estimated the CO2 emissions generated during the manufacturing, driving, and disposal stages of cars, to analyze the impact of car sharing on CO2 emissions. Then, we determined the changes in the life-cycle CO2 emissions of all the cars for three car-sharing penetration rates (0, 5, and 100%), assuming that all the cars were gasoline-powered. Additionally, we analyzed how electric vehicles can optimize the proposed strategy. An increase in car-sharing services significantly reduced vehicular CO2 emissions; the decrease in CO2 emissions from private cars when owners switched to car services significantly exceeded the increase in the CO2 emissions associated with the increased number of cars. The proposed model can serve as a reliable framework to analyze the current status of CO2 emissions and simulate the future changes in car-sharing services.

Ultra-low emission power generation utilizing chemically stabilized waste plastics pyrolysis oil in RCCI combustion concept

Emission standards in European Union, designed to reduce the environmental impact of power generation, present a significant challenge for fast-response distributed power generation systems based on internal combustion engines. Regulated emissions, such as NOx and particulate matter present a major concern due to their adverse number of environmental and health effects. Simultaneously, European Union strives towards sustainable management of plastic waste and seeks the ways for its upcycling and production of new fuels and chemicals. As an answer to the presented challenges, the present experimental study addresses the potential for use of chemically stabilized Waste Plastics Oil (WPO), a product of pyrolysis process of waste plastics in a Reactivity Controlled Compression Ignition (RCCI) combustion concept. To establish a reactivity-controlled combustion, the study uses a combination of methane (a model fuel for biomethane) and WPO to a) simultaneously reduce NOx and particulate matter emissions due to low local combustion temperatures and a high degree of charge homogenization and b) address waste and carbon footprint reduction challenges. Through experiments, influence of direct injection timing and energy shares of utilized fuels to in-cylinder thermodynamic parameters and engine emission response were evaluated in engine operating points at constant indicated mean effective pressure. Acquired results were deeply investigated and benchmarked against compression ignition (CI) and RCCI operation with conventional diesel fuel to determine potential for WPO utilization in an advanced low-temperature combustion concept. Results show that chemically stabilized WPO can be efficiently utilized in RCCI combustion concept without adaptation of injection parameters and that with suitable control parameters, ultra-low emissions of NOx and PM can be achieved with utilized fuels. For diesel/methane mix, NOx and PM emissions were reduced compared to conventional CI operation for 82.0% and 93.2%, respectively, whereas for WPO/methane mix, NOx and PM emissions were reduced for 88.7% and 97.6%, respectively, which can be ascribed to favourable chemical characteristics of WPO for the utilized combustion concept. In the least favourable operating point among those studied, indicated mean effective pressure covariance was kept below 2.5%, which is well below 5% being considered the limit for stable engine operation.

Emission Measurements on a Large Sample of Heavy-Duty Diesel Trucks in China by Using Mobile Plume Chasing

Real-world heavy-duty diesel trucks (HDTs) were found to emit far more excess nitrogen oxides (NOX) and black carbon (BC) pollutants than regulation limits. It is essential to systematically evaluate on-road NOX and BC emission levels for mitigating HDT emissions. This study launched 2109 plume chasing campaigns for NOX and BC emissions of HDTs across several regions in China from 2017 to 2020. It was found that NOX emissions had limited reductions from China III to China V, while BC emissions of HDTs exhibited high reductions with stricter emission standard implementation. This paper showed that previous studies underestimated 18% of NOX emissions in China in 2019 and nearly half of the real-world NOX emissions from HDTs (determined by updating the emission trends of HDTs) exceeded the regulation limits. Furthermore, the ambient temperature was identified as a primary driver of NOX emissions for HDTs, and the low-temperature penalty has caused a 9-29% increase in NOX emissions in winter in major regions of China. These results would provide important data support for the precise control of the NOX and BC emissions from HDTs.

The effect of various urea-in-water solution types on exhaust particle number emission

In order to qualitatively evaluate the impact of urea-in-water solution on the particle number emission, five different urea types were chosen under diesel engine bench test. The results show that compared to the instantaneous particle concentrations without injection, the instantaneous particle concentrations with injection increase distinctly, which are larger around 0.3-1.2 times than that without urea-in-water solution. At high speed phase, the instantaneous particle concentrations with urea-in-water solution injection rise obviously, especially for C and E solutions. In addition, the particle size distribution characteristic does not change with the urea-in-water solution dosing. The PN emission factors follow the sequence of C solution > E solution > A solution > B solution > D solution. It is deduced that the metallic element contents in the urea-in-water solution play a key role for the PN emission factor. In the future, the particle formation due to urea-in-water solution injection should be given more attention.

Assessment and usability of Jatropha biodiesel blend with phenolic antioxidant to control NOx emissions of an unmodified diesel engine

The excessive utilization of fossil fuels has worsened global warming and exacerbated the levels of air pollution in the environment, forcing us to consider alternative fuels for compression ignition engines. The current research aims to explore the possibilities of renewable fuels outperforming diesel fuel in terms of combustion, performance, and emission characteristics. Biodiesel is an environmentally friendly and renewable alternative fuel. The major drawback of biodiesel is the significant rise in nitrogen oxide (NOx) emissions. The main novelty and objective of this research is to investigate the performance and emission characteristics of variable compression ratio diesel engine using DPA antioxidant additive. For this investigation, diesel, Jatropha biodiesel (B30) and 100 ppm of phenolic antioxidant diphenylamine (DPA) blended with B30 have been used as fuel named B30+DPA100. From experimental outcomes, the inclusion of diphenylamine to B30 blend resulted in brake-specific fuel consumption (BSFC) and exhaust gas temperature (EGT) being reduced by 8.86% and 4.12%, respectively, compared to B30. Simultaneously, there was a 1.11% increase in brake thermal efficiency (BTHE). The B30+DPA100 fuel blend demonstrates effective control over NOx and other emissions. The emissions of NOx, carbon monoxide (CO), hydrocarbon (HC), and smoke from the B30+DPA100 blend have shown a reduction of 6.8%, 5.34%, 7.86%, and 15.67%, respectively, when compared to diesel. However, there has been an increase in carbon dioxide (CO2) by 7.8%. One notable advantage of the B30+DPA100 blend is the significant decrease in NOx emissions. Additionally, the cylinder pressure for B30+DPA100 has been lowered by 4.93% compared to B30. On the other hand, the net heat release rate (NHR) has experienced a 1.72% increase. The particle size of different elements present in the crankcase oil has been calculated by Zetasizer Nano. The analysis revealed varying particle sizes for different elements in the crankcase oil: aluminum (2.724 μm), chromium (2.78 μm), iron (2.423 μm), and lead (2.587 μm).

Biodiesel production from Mastic oil via electrolytic transesterification: optimization using response surface methodology and engine test

This study aimed to synthesize the biodiesel from Mastic oil by electrolysis method. Mastic gum is a potential and inexpensive feedstock for the biodiesel production. The oil content of Mastic gum was ~ 20% of the total gum weight. The gas chromatography-mass spectrometry (GC-MS) analysis was exploited to measure the oil's fatty acid profile. The response surface methodology (RSM) via Box-Behnken design (BBD) was utilized to specify the best processing condition of the electrolytic transesterification process. According to the RSM-BBD results, the highest predicted biodiesel yield was 95% at the reaction time of 1 h, methanol to oil ratio of 4:1, and catalyst weight of 1.2 wt%. Under these conditions, the produced Mastic oil biodiesel was blended with the neat diesel at different volume ratios of 5:95 (B5), 10:90 (B10), and 15:85 (B15). These fuel mixtures were tested in a single-cylinder engine to assess engine performance and exhaust emissions. The experiments exhibited that blending biodiesel with diesel can slightly improve the engine performance. Moreover, the application of blends with high volumes of biodiesel decreased the exhaust emissions, such as carbon monoxide (CO), carbon dioxide (CO2), and unburned hydrocarbons (UHC) by 54.54%, 41%, and 39.3%, respectively. However, the nitrogen oxide (NOx) emission increased because of the higher oxygen content of the biodiesel. It was also found that the physical and chemical characteristics of the Mastic oil biodiesel are the same as diesel, consistent with the ASTM standard. The Fourier transform infrared (FTIR) analysis also confirmed the biodiesel production.

Differences in compositions and effects of VOCs from vehicle emission detected using various methods

Vehicle exhaust and oil fuel evaporation emit volatile organic compounds (VOCs). The differences in VOC compositions and their effects determined using different methods have not been addressed sufficiently. In this study, VOC samples are obtained from single gasoline and diesel vehicle exhausts using a portable emission measurement system, from a tunnel in Yichang City, and from gasoline and diesel evaporation at gas stations. A total of 107 VOCs are analysed. The calculated VOC source profiles (based on VOC source profiles of single-vehicle type and vehicle fleet composition in the tunnel) and the tested source profiles (from a tunnel test) are compared. The results show that gasoline burning can reduce alkenes from a mass fraction of 53.1% (for evaporation) to 3.6% (for burning), as well as increase the mass fraction of alkenes from 1.3% (for diesel evaporation) to 34.0% (for diesel burning). The calculated VOC source profiles differed from the tested VOC source profiles, with a coefficient of divergence of 0.6. Ethane, ethylene, n-undecane, and n-dodecane are used to distinguish VOCs in gasoline and diesel exhausts. Cis-2-butene, 2-methylpentane, m/p-xylene, o-xylene, and n-decane can be used to separate gasoline from diesel. The xylene/ethylbenzene ratios accurately reveal the photochemical age. Gasoline burning increases health risks associated with VOCs compared with gasoline evaporation. Furthermore, it modifies the main contributor to ozone formation potential. This study is expected to facilitate refined VOC source apportionment and studies pertaining to speciated emission inventories.

Physical properties and structural characteristics of particulate matter emitted from a diesel engine fueled with biodiesel blends

This research explores the influence of renewable fuels, including three kinds of biodiesel along with ethanol on the physical properties and structural characteristics of particulate matter (PM) emitted from a diesel engine in comparison with pure diesel. After adding 10 vol% of grape seed biodiesel, coffee biodiesel and eucalyptus oil into diesel, three biodiesel blended fuels (10% grape seed biodiesel (DGs10), 10% spent coffee ground biodiesel (DC10) and eucalyptus oil biodiesel (DEu10)) were produced and tested in this study. Besides, one ethanol blend containing 9 vol% of ethanol and 1 vol% of biodiesel (blend stabilizer) was also tested to do the comparison. In the present study, scanning transmission electron microscope (STEM) and scanning electron microscope (SEM) were employed for analyzing the microstructure, nanostructure and electron diffraction pattern of PM. Raman spectrometer (RS) was also used for the analysis of structural characterization of PM. In addition, several experimental instruments like microbalance, measuring cup, viscometer, oxygen bomb calorimeter and Gas Chromatography-Mass Spectrometer (GC-MS) were employed to detect the fuel properties, including density, heating value, viscosity, composition and cetane number. A conclusion can be drawn that both biodiesel blends and ethanol blend have a changing effect on the PM properties compared to pure diesel, where biodiesel blends have a slightly weaker influence than ethanol blend. Regarding the biodiesel blends, DGs10 has more impact than DC10 and DEu10 in changes of PM properties, particularly in the reduction of PM mass, making it a good candidate for renewable fuel for diesel engines.

Evaluating vehicular exhaust and evaporative emissions via VOC measurement in an underground parking garage

Vehicular emissions, including both tailpipe exhaust and evaporative emissions, are major anthropogenic sources of volatile organic compounds (VOCs) in urban cities. Current knowledge on vehicle tailpipe and evaporative emissions was mainly obtained via laboratory tests on very few vehicles under experimental conditions. Information on fleet gasoline vehicles emission features under real-world conditions is lacking. Here, VOC measurement was conducted in a large residential underground parking garage in Tianjin, China, to reveal the feature of the exhaust and evaporative emissions from real-world gasoline vehicle fleets. The VOC concentration in the parking garage was on average 362.7 ± 87.7 μg m-3, significantly higher than that in the ambient atmosphere at the same period (63.2 μg m-3). Aromatics and alkanes were the mainly contributors on both weekdays and weekends. A positive correlation between VOCs and traffic flow was observed, especially in the daytime. Source apportionment through the positive matrix factorization model (PMF) revealed that the tailpipe and evaporative emissions accounted for 43.2% and 33.7% of VOCs, respectively. Evaporative emission contributed 69.3% to the VOCs at night due to diurnal breathing loss from numerous parked cars. In contrast, tailpipe emission was most remarkable during morning rush hours. Based on the PMF results, we reconstructed a vehicle-related VOCs profile representing the combination of the tailpipe exhaust and evaporative emission from fleet-average gasoline vehicles, which could benefit future source apportionment studies.

The combined effect of acetone and ZnO with diesel-biodiesel blends on the performance, combustion and emission characteristics of diesel engine

In this experimental study, the performance, combustion and emission analysis of the combined effect of acetone and Zinc Oxide (ZnO) dispersed diesel-biodiesel (B20) blends were done in four-stroke, single-cylinder and water-cooled diesel engine. ZnO was synthesized by the solvothermal method using cow urine as a solvent and reducing agent. The synthesized ZnO was characterized by X-ray diffraction (XRD) and Scanning Electron Microscope (SEM). The biodiesel was produced from waste cooking oil through a trans-esterification process. The synthesized ZnO was dispersed in 10, 20 and 30 ppm with diesel-biodiesel blend along with 10% of acetone to form B20A10Zn10, B20A10Zn20 and B20A10Zn30 test fuels. The experimental results show that adding acetone and ZnO with diesel-biodiesel blend tends to promising physiochemical properties of the test fuels and produced better results in performance and emission. The test fuel, B20A10Zn30, gave a better outcome than all other fuels and recorded a 0.4% increase in Brake Thermal Efficiency (BTE), while there was an 8% increase in Brake Specific Fuel Consumption (BSFC). Compared to diesel, the emissions, such as Carbon Monoxide (CO), Unburned Hydrocarbon (UHC), Oxides of Nitrogen (NOx), and smoke, were 7.97%, 20%, 1.8% and 1.49% lower than the conventional diesel.

Effect of green fuel and green lubricant with metallic nanoparticles on emissions of HC, CO, NOx, and smoke for a compression ignition engine

The United Nations Sustainable Development Goals (SDGs) are imperative from the point of view of protecting the environment by employing sustainable options. Considerable research has been carried out in the transportation sector to meet this objective. Here, the influence is assessed of epoxidised gingelly oil methyl ester biolubricant with alumina (Al2O3) nanoparticles on the performance and emissions of a single cylinder 0.66-L capacity direct injection compression ignition engine driven by gingelly B20 biodiesel. Engine tests are carried out with gingelly B20 biodiesel as a fuel, and gingelly methyl ester (B100), epoxidised gingelly methyl ester (B100E), and epoxidised gingelly methyl ester (B100E) mixed with 0.5%, 1.0%, and 1.5% w/w alumina (Al2O3) nanoparticles as the lubricant combinations. The results are compared with baseline B20 biodiesel fuel-mineral lubricant operation. The findings indicate that brake thermal efficiency increases by 8.64% for epoxidised gingelly methyl ester (B100E) with 1.0% w/w alumina (Al2O3) nanoparticle biolubricant in comparison to baseline operation. Considerable reductions in emissions are detected; specifically, reductions of 52.4%, 22.0%, 20.0%, and 34.9%, respectively, are observed for CO, NOx, and HC concentrations and smoke opacity for the abovementioned combination as compared to baseline operation. The present work suggests that further research is merited on green fuel-green lubricant combinations. The findings of this study address the United Nations Sustainable Development Goals (SDGs) 7 and 13.

Biogeochemical modelling to assess benzene removal by biostimulation in aquifers containing natural reductants

Biostimulation of aquifers contaminated with gasoline spills is vigorously affected by the biogeochemical environment existing there. In this study, biostimulation of benzene is simulated using a 2D coupled multispecies biogeochemical reactive transport (MBRT) model. The model is implemented at an oil spill site near a hypothetical aquifer containing natural reductants. Multiple electron acceptors are introduced to promote faster biodegradation rate. However, after reaction with natural reductants, it reduces the number of available electron acceptors, acidifies the subsurface environment, and inhibits bacterial growth. These mechanisms are assessed using seven coupled MBRT models sequentially. The finding of the present analysis reveals that biostimulation has caused a substantial drop in concentration of benzene and is efficient in reducing its penetration depth. The results also shows that the intervention of natural reductants in the biostimulation process is slightly diminished by pH adjustment of aquifers. When the pH level in aquifer changes from acidic pH 4 to neutral pH 7, it is observed that the biostimulation rate of benzene as well as microbial activity increases. Electron acceptors consumption is more at neutral pH. Overall, it can be inferred from zeroth-order spatial moment and sensitivity analyses that retardation factor, inhibition constant, pH, and dispersivity in vertical direction significantly affect benzene biostimulation in aquifers.

Historical trends of traditional, emerging, and halogenated polycyclic aromatic hydrocarbons recorded in core sediments from the coastal areas of the Yellow and Bohai seas

Historical trends of polycyclic aromatic hydrocarbons (PAHs) contamination were reconstructed from eleven sediment cores located in intertidal zones of the Yellow and Bohai seas for a period encompassing the last 80 years. The analysis encompassed 15 traditional PAHs (t-PAHs), 9 emerging PAHs (e-PAHs), and 30 halogenated PAHs (Hl-PAHs), including 10 chlorinated PAHs (Cl-PAHs) and 20 brominated PAHs (Br-PAHs). Concentrations of target PAHs were highest in industrial and municipal areas situated along the coast of the Bohai Sea, including Huludao, Yingkou, Tianjin, and Dandong, constituting a substantial mass inventory. All target PAHs showed increasing trends since the 1950s, reflecting the development history of South Korea and China. High molecular weight PAHs accumulated in sampling sites more than low molecular weight PAHs. A positive matrix factorization model showed that the PAH sources were coal and gasoline combustion (35%), diesel combustion (33%), and biomass combustion (32%). Over the last 80 years, the contribution of coal and gasoline combustion increased in all regions, while diesel combustion and biomass combustion varied across regions and over time. Toxicity equivalence values were highest for t-PAHs (>99% contribution), followed by Cl-PAHs, Br-PAHs, and e-PAHs. Concentrations of t-PAHs in Eastern Asia seas have increased since the 1900s, particularly in intertidal areas compared to subtidal areas. The intertidal zone removed 83% of the total flux of PAHs originating from land and thus appears to serve as a buffer zone against marine pollution. Overall, this study provides novel knowledge on the historical trends and sources of PAHs on a large scale, along with insights for future coastal management.

Energy-saving and emission-reduction potential of fuel cell heavy-duty trucks in China during the fuel life cycle

Exploring alternative fuels and advanced vehicle technology is a crucial strategy for vehicle emission reduction. Fuel cell heavy-duty trucks (FC-HDTs) have a promising application prospect to alleviate the high energy consumption and emissions of road freight, but their environmental performance during the fuel life cycle should be further studied. This study is aimed at evaluating the fossil fuel consumption and GHG emissions of FC-HDTs in China using the updated GREET model. The results show that (1) comparing various hydrogen production pathways, it is found that the coke oven gas (COG) pathway can provide the best environmental performance, while the energy consumption and greenhouse gas (GHG) emissions of the coal gasification (CG) and grid power water electrolysis (GPWE) pathways will be significantly decreased in the future. (2) Among the involved vehicles in China, FC-HDT with GVWR18 has the greatest energy-saving and emission-reduction potential. (3) The application of carbon capture and storage (CCS) technology in hydrogen production is conducive to improving the emission-reduction effect of FC-HDT while increasing its energy consumption slightly. The key to achieving upstream carbon neutrality is to optimize the hydrogen production structure and electricity mix, along with adjusting the hydrogen production process and transportation mode. Furthermore, the fuel economy and payload of the FC-HDT affect its environmental performance, indicating the importance of improving the technology of the drivetrain, fuel cell, and hydrogen storage tank.

Characterizing sources and ozone formations of summertime volatile organic compounds observed in a medium-sized city in Yangtze River Delta region

Volatile organic compounds (VOCs) emitted from various sources into atmosphere could cause serious O₃ pollution in urban areas. Although characterizations of ambient VOCs have been extensively studied in megacities, they are scarcely investigated in medium/small-sized cities, which could present different pollution characterizations due to the factors like emission sources and populations. Herein, field campaigns were conducted concurrently at six sites in a medium-sized city of Yangtze River Delta region to determine ambient levels, O₃ formations and source contributions of summertime VOCs. During the observation period, the total VOC (TVOCs) mixing ratios ranged from 27.10 ± 3.35 to 39.09 ± 10.84 ppb at six sites. The ozone formation potential (OFP) results showed that alkenes, aromatics and oxygenated VOCs (OVOCs) were dominant contributors, together sharing 81.4% of total calculated OFPs. Ethene ranked the largest OFP contributor at all six sites. A high VOC site, KC, was selected as a case to detailed analyze diurnal variations of VOCs and its relationship with O₃. Consequently, diurnal patterns varied with VOC groups, and TVOC concentrations were lowest during strong photochemical period (15:00-18:00 p.m.), opposite to the O₃ peak. VOCs/NOx ratios and observation-based model (OBM) analysis revealed that O₃ formation sensitivity was primarily in transition regime in summertime and that the reduction of VOCs rather than NO_X would be more efficient to suppress O₃ peak at KC during pollution episode. Additionally, source apportionment conducted with positive matrix factorization (PMF) indicated that industrial emission (29.2%-51.7%) and gasoline exhaust (22.4%-41.1%) were major sources for VOCs at all six sites, and that VOCs from industrial emissions and gasoline exhaust were the key precursors for ozone formation. Our results shed light on the importance of alkenes, aromatics and OVOCs in forming O₃ and propose that preferentially reducing VOCs especially those from industrial emission and gasoline exhaust would benefit alleviating O₃ pollution.

Modeling fuel consumption and emissions by taxis in Tabriz, Iran: uncertainty and sensitivity analyses

Taxis pose a higher threat to global climate change and human health through air emissions. However, the evidence on this topic is scarce, especially, in developing countries. Therefore, this study conducted estimation of fuel consumption (FC) and emission inventories on Tabriz taxi fleet (TTF), Iran. A structured questionnaire to obtain operational data of TTF, municipality organizations, and literature review were used as data sources. Then modeling was used to estimate fuel consumption ratio (FCR), emission factors (EFs), annual FC, and emissions of TTF using uncertainty analysis. Also, the impact of COVID-19 pandemic period was considered on the studied parameters. The results showed that TTF have high FCRs of 18.68 L/100 km (95% CI=17.67-19.69 L/100 km), which are not affected by age or mileage of taxis, significantly. The estimated EFs for TTF are higher than Euro standards, but the differences are not significant. However, it is critical as can be an indication of inefficiency of periodic regulatory technical inspection tests for TTF. COVID-19 pandemic caused significant decrease in annual total FC and emissions (9.03-15.6%), but significant increase in EFs of per-passenger-kilometer traveled (47.9-57.3%). Annual vehicle-kilometer-traveled by TTF and the estimated EFs for gasoline-compressed natural gas bi-fueled TTF are the main influential parameters in the variability of annual FC and emission levels. More studies on sustainable FC and emissions mitigation strategies are needed for TTF.

Life cycle water footprint of electric and internal combustion engine vehicles in China

With the expansion of China's automobile market and the increase in the proportion of electric vehicles, the influence of the automobile industry on water resources has been increasingly, and as a result, water resources will become an important factor restricting the development of the electric vehicle industry in China. Until now, there are still no in-depth studies on the influences of the water footprint of electric vehicles. The paper establishes a life cycle assessment model by which to analyze the reduction potential of the water footprint of various types of passenger vehicles in their operation. The paper also compares the water footprint of passenger vehicles under different power structures, revealing the potential influence of developing electric vehicles on the demand of water resources. The results show that at the base year (2019), the plug-in hybrid electric vehicles and battery electric vehicles consume more water than the gasoline-based internal combustion engine vehicles do, while water consumption of the hybrid electric vehicles and fuel cell vehicles is lower than that of the gasoline-based internal combustion engine vehicles; as for the year 2035, even after the proportion of renewable energy generation increases, the water withdrawal and consumption of the battery electric vehicles and plug-in hybrid electric vehicles will still be larger than those of the gasoline-based internal combustion engine vehicles.

Exhaust emissions of gaseous and particle size-segregated water-soluble organic compounds from diesel-biodiesel blends

This study assessed the emissions of gaseous pollutants and particle size distributed water-soluble organics (WSO) from a diesel vehicle fuelled with ultralow sulphur diesel (B0) and 10 (B10), 20 (B20), and 30% (B30) biodiesel blends in a chassis dynamometer tested under transient mode. Particulate emission sampling was carried out in an ultraviolet (UV) test chamber using a 10-stage impactor. Samples were grouped into three size fractions and analysed by gas chromatography-mass spectrometry. Increasing the biofuel ratio up to 30% in the fuel reduced WSO emissions by 20.9% in comparison with conventional diesel. Organic acids accounted for 82-89% of WSO in all tested fuels. Dicarboxylic acids were the most abundant compound class, followed by hydroxy, aromatic, and linear alkanoic acids. Correlations between compounds demonstrated that adding biodiesel to diesel fuel reduces the emissions of nitrogen oxides (NOx), benzene, toluene, ethylbenzene and xylenes (BTEX), methane (CH4), total and nonmethane hydrocarbons (THC and NMHC), and dicarboxylic and hydroxy acids, but increases emissions of carbon dioxide (CO2) and alkanoic and aromatic acids. Emissions of dicarboxylic and hydroxy acids were strongly correlated with the biodiesel content. WSO emissions of coarse and fine (1.0-10 μm) particles decreased with the increasing biofuel content in fuel blend. The total share of ultrafine (0.18-1.0 μm) and nanoparticles (< 0.18 μm) increased in WSOs emissions from B20 and B30 blends, when compared with petrodiesel. The biodiesel content also affected the chemical profile of WSO size fractions.

Impacts on real-world extra cold start emissions: Fuel injection, powertrain, aftertreatment and ambient temperature

Vehicles emit substantial amounts of pollutants during start periods. Engine starts mainly occur in urban areas, causing serious harm to humans. To investigate the impacts on extra cold start emissions (ECSEs), eleven China 6 vehicles with various control technologies (fuel injection, powertrain, and aftertreatment) were monitored with a portable emission measurement system (PEMS) at different temperatures. For conventional internal combustion engine vehicles (ICEVs), the average ECSEs of CO₂ increased by 24%, while the average ECSEs of NOx and particle number (PN) decreased by 38% and 39%, respectively, with air conditioning (AC) on. Gasoline direct injection (GDI) vehicles had 5% lower CO₂ ECSEs, but 261% higher NOx ECSEs and 318% higher PN ECSEs than port fuel injection (PFI) vehicles at 23 °C. The average PN ECSEs were significantly reduced by gasoline particle filters (GPFs). The GPF filtration efficiency was higher in GDI than PFI vehicles due to particle size distribution. Hybrid electric vehicles (HEVs) generated excessive PN extra start emissions (ESEs), resulting in a 518% increase compared to ICEVs. The start times of the GDI-engine HEV accounted for 11% of the whole test time, but the proportion of PN ESEs relative to total emissions were 23%. Linear simulation based on the decrease in ECSEs with increasing temperature underestimated the PN ECSEs from PFI and GDI vehicles by 39% and 21%, respectively. For ICEVs, CO ECSEs varied with temperature in a U shape with a minimum at 27 °C; NOx ECSEs decreased as ambient temperature increased; PFI vehicles generated more PN ECSEs at 32 °C than GDI vehicles, stressing the significance of ECSEs at high temperature. These results are useful for improving emission models and assessing air pollution exposure in urban aeras.

Environment impact assessment of agricultural diesel engines utilizing biodiesel derived from phoenix sylvestris oil

Uncontrolled emissions, massive price increases, and other factors encourage searching for a suitable diesel engine fuel alternative. In its processed form, vegetable oil biodiesel is an appealing green alternative fuel for compression ignition engines. Vegetable oil esters have qualities comparable to those of standard diesel fuel. As a result, biodiesel may be utilized to run a diesel engine without any further alterations. This article analyses the potential of Phoenix sylvestris oil, which may be found in forest belts across the globe, as a viable feedstock for biodiesel extraction. Phoenix sylvestris oil is found to be abundant in different forest belts worldwide. The free fatty acid must first be transformed into esters using catalytic acid esterification before proceeding to alkaline catalytic esterification. The molar ratio (6:1), catalyst concentration (1 wt%), reaction temperature (60 °C), and reaction time (2 h) have all been optimized for biodiesel extraction. Biodiesel produced had characteristics that were similar to standard biodiesel specifications. The biodiesel yield from Phoenix sylvestris oil was 92.3% under optimum conditions. The experimental results revealed that the Phoenix sylvestris oil biodiesel performed better than neat Phoenix sylvestris oil and its blends. Phoenix sylvestris oil blend produced better brake thermal efficiency with lower smoke, hydrocarbon, and CO emissions. The biodiesel produced from non-edible Phoenix sylvestris oil has the potential to be employed as a viable alternative to diesel fuel.

Effects of high cetane diesel on combustion, performance, and emissions of heavy-duty diesel engine

Fuel economy improvement and reducing exhaust emissions are drivers for advancement in engine technology and fuel quality enhancement. The latest generation diesel engine uses a high pressure common rail fuel injection system and after-treatment devices such as selective catalyst reduction (SCR) and diesel particulate filters (DPF) to meet the stringent emission norms. The performance of engine can be further improved by using better quality fuel than the minimum requirement. Fuel quality improvement can be achieved through modifying blending components and/ or using additives. This study investigates the effect of high cetane diesel on the performance and emission behavior of SCR fitted heavy-duty engines. Normal diesel is doped with diesel multi-functional additives containing cetane improver, and thereby cetane number enhanced to 55 from 52. Fuel consumption and exhaust emission were evaluated over the European stationary cycle (ESC) under the controlled test cell conditions. The fuel consumption with the high cetane diesel was 0.5% lower; CO, HC, and NOx emissions were lower by 12%, 6%, and 8% respectively over the ESC. This paper also highlights mode-wise engine performance, emissions, noise, and combustion behavior of the engine while using a cetane improver in diesel over the ESC cycle. Noise level reduced by 1 dB in the wide-open throttle performance tests when the cetane number increased by 3 units.

Optimization of Bauhinia parviflora biodiesel production for higher yield and its compatibility assessment with water and Di-tert-butyl peroxide emulsion

The current study aims to attain a higher yield of biodiesel from Bauhinia tree seed wastes through process optimization using response surface methodology (RSM) and assess its compatibility in the diesel engine blended with water and Di-tert-butyl peroxide (DTBP). The Bauhinia parviflora biodiesel (BPB) transesterification originated using a fixed quantity of catalyst, and the transesterification process parameters such as oil-molar ratio (OMR), process temperature (PT), and reaction time (RT) were optimized. Fourier transform infrared spectroscopy (FTIR) and Gas chromatography-mass spectrometry (GC-MS)analysis were applied to characterize and quantify the BPB, and ASTM standards were followed to measure the properties. The prepared BPB (30%) was blended with 10% water and 2% BTBP to enhance the performance and emission characteristics of the BPB in the diesel engine. The optimization result implies that the higher yield of BPB (91.4%) was attained for OMR of 9.2:1, PT of 76 °C, and RT of 67 min. The FTIR report indicates that the carbon-based components are pretty good in the prepared BPB. The GC-MS report indicates that the fatty acids are converted into corresponding methyl esters, and the measured fuel properties are within the prescribed limits. The diesel engine's performance is effectively improved for the BPB blended with water and DTBP. The proposed fuel's overall improvement in hydrocarbon, carbon monoxide, smoke, and oxides of nitrogen emissions is 27.2%, 34.9%, 16.7%, and 11.2%, respectively.

Global decrease in blood lead concentrations due to the removal of leaded gasoline

Lead (Pb) is a chemical element with extreme toxicity that is classified as one of the ten chemicals of most significant concern to human health. The main problem involving Pb is its use as a fuel additive (tetraethyllead - TEL) at a global level, which raised the atmospheric Pb concentrations. It is estimated that between 80 and 90% of the atmospheric Pb in large cities came from the use of TEL, and as a consequence, it was also the main source responsible for human exposure to the element. Therefore, this work aimed to evaluate, through a systematic review, the blood concentrations of Pb in scientific articles published in the first two decades of the 2000s to compare the global and regional trends of each continent over time. Our data show the importance of removing TEL in decreasing human exposure to Pb worldwide. We observed exponentially decreasing blood Pb concentrations over the years after additive removal on all continents, resulting in a global trend which TEL's use was the major process governing human exposure worldwide. In addition, the results also showed that, despite the removal of Pb additives lowering levels of human blood Pb, the general population remains exposed to the element through exogenous and endogenous sources. The exhaust Pb particles were deposited into the environment in proportion to the traffic flows, and the legacy of Pb in the environment requires novel primary prevention remedy to curtail exposure.

Removal of a complex VOC mixture by potted plants-effects on soil microorganisms

Microorganisms in the soil of potted plants are important for removal of volatile organic compounds (VOCs) from indoor air, but little is known about the subject. The aim of this study was therefore to obtain a better understanding of the effect of VOCs on the microbial community in potted plants. Hedera helix was exposed to gasoline vapors under dynamic chamber conditions for 21 days and three main parameters were investigated. These were (1) removal of the target compounds heptane, 3-methylhexane, benzene, toluene, ethylbenzene, m,p-xylene, and naphthalene from the gasoline mixture; (2) toluene mineralization; and (3) bacterial abundance and bacterial community structure. H. helix was able to reduce the concentration of the target compounds in the continuously emitted gasoline by 25-32%, except for naphthalene, which was too low in concentration. The soil microcosm of gasoline exposed plants had for an initial 66 h increased toluene mineralization rate compared to the soil microcosm in the soil of plants exposed to clean air. Bacterial abundance was decreased in response to gasoline exposure while bacterial community structure was changed. The change in bacterial community structure was, however, different between the two experiments indicating that several taxonomic units can degrade gasoline components. Especially the genera Rhodanobacter and Pseudonorcardia significantly increased in abundance in response to gasoline vapors. Bauldia, Devosia, and Bradyrhizobium, on the other hand, decreased.

Phytoremediation as a potential technique for vehicle hazardous pollutants around highways

With the synchronous development of highway construction and the urban economy, automobiles have entered thousands of households as essential means of transportation. This paper reviews the latest research progress in using phytoremediation technology to remediate the environmental pollution caused by automobile exhaust in recent years, including the prospects for stereoscopic forestry. Currently, most automobiles on the global market are internal combustion vehicles using fossil energy sources as the primary fuel, such as gasoline, diesel, and liquid or compressed natural gas. The composition of vehicle exhaust is relatively complex. When it enters the atmosphere, it is prone to a series of chemical reactions to generate various secondary pollutants, which are very harmful to human beings, plants, animals, and the eco-environment. Despite improving the automobile fuel quality and installing exhaust gas purification devices, helping to reduce air pollution, the treatment costs of these approaches are expensive and cannot achieve zero emissions of automobile exhaust pollutants. The purification of vehicle exhaust by plants is a crucial way to remediate the environmental pollution caused by automobile exhaust and improve the environment along the highway by utilizing the ecosystem's self-regulating ability. Therefore, it has become a global trend to use phytoremediation technology to restore the automobile exhaust pollution. Now, there is no scientific report or systematic review about how plants absorb vehicle pollutants. The screening and configuration of suitable plant species is the most crucial aspect of successful phytoremediation. The mechanisms of plant adsorption, metabolism, and detoxification are reviewed in this paper to address the problem of automobile exhaust pollution.

Performance, combustion and emission characteristics of a diesel engine fuelled with diesel fuel + corn oil + alcohol ternary blends

A blend of diesel fuel and corn oil in the ratio of 80:20 (v/v) is prepared. 1-butanol and 1-pentanol are mixed separately with the binary blend in different ratios (4:96, 7:93, and 10:90 v/v) to prepare ternary blends. Pure diesel fuel and ternary blends are tested at various engine speeds (1000-2500 rpm) and at full throttle position. A regression model and its trigonometric Fourier series are proposed to represent the variation of in-cylinder pressure vs. crank angle measured by the author. The regression model and its Fourier series are compared to the Gaussian function of second-order using the in-cylinder pressure data measured by the author and different authors. On average, the ternary blends have lower brake effective efficiency (0.7347 [Formula: see text]-4.0553 [Formula: see text]) and peak heat release rate (5.1113 [Formula: see text]-6.3083 [Formula: see text]), compared to diesel fuel. On average, the ternary blends have a shorter combustion duration (0.4045 [Formula: see text]-7.0236 [Formula: see text]) and longer ignition delay (8.3635 [Formula: see text]-13.9110 [Formula: see text]) relative to diesel fuel. The ternary blends produce lower CO (8.4769 [Formula: see text]-13.1598 [Formula: see text]), HC (30.0073 [Formula: see text]-36.2523 [Formula: see text]), and smoke (4.8566 [Formula: see text]-7.4181 [Formula: see text]) emissions while higher NO_X (3.2691 [Formula: see text]-10.8795 [Formula: see text]) emission. The estimated values from the proposed regression model and its Fourier series coincide quite well with in-cylinder pressure data measured by the author and different authors.