Doped graphitic carbon nitride (g-C3N4) catalysts for efficient photodegradation of tetracycline antibiotics in aquatic environments

SnS2 integrated P-doped g-C3N4 with advanced photocatalytic efficiency towards organic pollutants decontamination

In this study, the P doping and SnS2 deposition was controlled to get SnS2 integrated P-doped g-C3N4 photocatalysts. The prepared photocatalysts were analyzed by XRD, FESEM, HRTEM, PL, UV-DRS, XPS, and Zeta potential emphasizing their crystalline structures, morphological characteristics, charge carrier recombination, band gap energies, chemical compositions, and surface charge. These results confirmed successful P doping by substituting C and formation of heterojunction with SnS2. Synthesized materials exhibited good photodegradation efficiency towards organic pollutants: the antibiotic ciprofloxacin (CP) and the cationic dye Rhodamine B (RhB). Among the optimized composites, PCSn-5 (containing 5 wt% of SnS2 on PCN-2, 1 mmol P doped g-C3N4) achieved the highest degradation rates, achieving 99.45% degradation of RhB within 100 min and 89.44% degradation of CP within 120 min. P doping introduced new energy levels that significantly enhanced charge separation and heterojunctions formed improved light absorption, thereby enhancing photocatalytic efficiency. Scavenger analysis acknowledge that holes were primarily responsible for RhB degradation, while in CP degradation both superoxide radicals and holes were dominant species. The photocatalytic efficiency of PCSn-5 was assessed at various pH levels exhibited the peak performance at pH 3 for RhB and at neutral pH for CP. The photocatalyst exhibited strong stability with ≈ 2% reduction in efficiency after five cycles for both pollutants. Electrochemical analysis, conducted through Mott-Schottky plots and electrochemical impedance spectroscopy (EIS), revealed increased donor density and reduced charge resistance following the formation of the composites.

A focused review on photocatalytic potential of graphitic carbon nitride (g-C3N4) based metal oxide-nanostructures for effective remediation of most overused antibiotics

Researchers in the field of photocatalysis are interested in finding a solution to the problem of charge transfer and recombination in photodegradation mechanisms. The ideal photoactive catalyst would be inexpensive, environmentally friendly, easily manufactured, and highly efficient. Graphitic carbon nitride (g-C3N4) and metal oxide (MOx) based nanocomposites (g-CN/MOx) are among the photocatalysts that provide the best results in terms of charge transfer capacity, redox capabilities, and charge recombination inhibition. This article provides a comprehensive overview of the latest research on antibiotic removal from wastewater using photocatalysts based on g-C3N4 and metal oxides nanocomposites. Amoxicillin (AMX), Azithromycin (AZM), Cefixime (CFM), Ciprofloxacin (CIP), and Tetracycline (TC) are some of the common antibiotics that are the focus of this review article's examination of the photocatalytic behavior of various g-C3N4/metal oxide-based photocatalysts. A research gap demonstrates that many studies are required to use these nanocomposites for photodegradation of antibiotics. By providing a better grasp of the photocatalysis process, this review encourages scientists and researchers to develop an accurate and appropriate photocatalyst to reduce environmental risks. The main findings of this review article suggest that the cost-effective g-C3N4/MOx-based nanocomposites exhibit excellent photodegradation properties, high charge transfer, broadening light response, and charge separation. They promote enhanced charge transportation, superior electron conductivity, high redox capability, and suppressing charge recombination rate. The photodegradation mechanism involves various reactive oxygen species (ROSs), including superoxide radicals, hydroxyl radicals, and holes which promotes the photocatalysis process. The exact transportation mechanism of electrons and holes is unclear, but a rapid charge-carrier transit can significantly increase and speed up the photooxidation process.

Lattice Defects and Electronic Modulation of Flower-Like Zn3In2S6 Promote Photocatalytic Degradation of Multiple Antibiotics

Photocatalysis is an effective technique to remove antibiotic residues from aquatic environments. Typical metal sulfides like Zn3In2S6 have been applied to a wide range of photocatalytic applications. However, there are currently no readily accessible methods to increase its antibiotic-degrading activity. Here, a facile hydrothermal approach is developed for the preparation of flower-like Zn3In2S6 with tunable sulfur lattice defects. Photogenerated carriers can be separated and transferred more easily when there is an adequate amount of lattice defects. Moreover, lattice defect-induced electronic modulation enhances light utilization and adsorption properties. The modified Zn3In2S6 demonstrates outstanding photocatalytic degradation activity for levofloxacin, ofloxacin, and tetracycline. This work sheds light on exploring metal sulfides with sulfur lattice defects for enhancing photocatalytic activity.

Recent progresses in synthesis and modification of g-C3N4 for improving visible-light-driven photocatalytic degradation of antibiotics

Graphitic carbon nitride (g-C3N4) is a widely studied visible-light-active photocatalyst for low cost, non-toxicity, and facile synthesis. Nonetheless, its photocatalytic efficiency is below par, due to fast recombination of charge carriers, low surface area, and insufficient visible light absorption. Thus, the research on the modification of g-C3N4 targeting at enhanced photocatalytic performance has attracted extensive interest. A considerable amount of review articles have been published on the modification of g-C3N4 for applications. However, limited effort has been specially contributed to providing an overview and comparison on available modification strategies for improved photocatalytic activity of g-C3N4-based catalysts in antibiotics removal. There has been no attempt on the comparison of photocatalytic performances in antibiotics removal between modified g-C3N4 and other known catalysts. To address these, our study reviewed strategies that have been reported to modify g-C3N4, including metal/non-metal doping, defect tuning, structural engineering, heterostructure formation, etc. as well as compared their performances for antibiotics removal. The heterostructure formation was the most widely studied and promising route to modify g-C3N4 with superior activity. As compared to other known photocatalysts, the heterojunction g-C3N4 showed competitive performances in degradation of selected antibiotics. Related mechanisms were discussed, and finally, we revealed current challenges in practical application.

Tailoring functional two-dimensional nanohybrids: A comprehensive approach for enhancing photocatalytic remediation

Photocatalysis is gaining prominence as a viable alternative to conventional biohazard treatment technologies. Two-dimensional (2D) nanomaterials have become crucial for fabricating novel photocatalysts due to their nanosheet architectures, large surface areas, and remarkable physicochemical properties. Furthermore, a variety of applications are possible with 2D nanomaterials, either in combination with other functional nanoparticles or by utilizing their inherent properties. Henceforth, the review commences its exploration into the synthesis of these materials, delving into their inherent properties and assessing their biocompatibility. Subsequently, an overview of mechanisms involved in the photocatalytic degradation of pollutants and the processes related to antimicrobial action is presented. As an integral part of our review, we conduct a systematic analysis of existing challenges and various types of 2D nanohybrid materials tailored for applications in the photocatalytic degradation of contaminants and the inactivation of pathogens through photocatalysis. This investigation will aid to contribute to the formulation of decision-making criteria and design principles for the next generation of 2D nanohybrid materials. Additionally, it is crucial to emphasize that further research is imperative for advancing our understanding of 2D nanohybrid materials.

Rapid and sensitive detection of tetracycline residue in food samples using Cr(III)-MOF fluorescent sensor

As tetracycline antibiotics were used in the poultry sector, their residue in edible animal products may adversely affect food safety and human health. The development of selective and sensitive tetracycline sensors has garnered a lot of interest due to the complexity of food samples. Therefore, a fluorescent sensing probe based on chromium(III)-metal-organic framework was developed for the rapid detection of tetracycline. After the addition of tetracycline, blue emission at λem 410 nm was effectively quenched by the interaction between TC and Cr(III)-metal-organic framework material. Under optimized conditions (sensor concentration: 30 mg/L and pH: 10.0), the sensing probe showed a fast response time (1 min), and low detection limit (0.78 ng/mL) with a linear range (5-45 ng/mL). Interestingly, the Cr(III)-metal-organic framework was successfully applied to quantity tetracycline residue in chicken meat and egg samples with recoveries of 95.17-06.93%. To deduce, our work can provide a new strategy for the direct detection of tetracycline in food samples.

Green synthesis of rectangular hollow tubular carbon nitride via in-situ self-assembly strategy to enhance the degradation of tetracycline hydrochloride under visible light irradiation

It has been an urgent requirement for materials with remarkable performance in the photocatalytic degradation of organic contaminants by photocatalytic technology. Limited surface area and speedy recombination rate of photogenerated charge carriers seriously restrain the application of g-C3N4. Morphology control is a powerful approach to enhance the photocatalytic efficiency of g-C3N4. Herein, we reported a method to attain graphitic carbon nitride with rectangular hollow tubular morphology and asperous surface (TUM-CN-2) which is prepared from urea-melamine hydrothermal products and trithiocyanuric acid by self-assembling without using organic solvents or template agents. The specific surface area, photocatalytic activity, and photo-generated carriers migration and separation rate of the obtained photocatalyst TUM-CN-2 are vastly improved. Contrasted with pure g-C3N4, the degradation rate of tetracycline hydrochloride (TCH) and Rhodamine B (RhB) was enhanced about 3.04 and 13.96 times in visible light irradiation, respectively. Moreover, the interference parameters, active free radicals, potential degradation mechanism, and degradation paths of TCH were researched systematically. This work provides a green way to acquire the modified g-C3N4 with splendid catalytic activity through the self-assembly method.

Degradation of Tetracycline with Photocatalysis by CeO2-Loaded Soybean Powder Carbon

In the process of using photocatalysts to treat tetracycline (TC) wastewater, the degradation efficiency of soybean powder carbon material (SPC) can be improved by loading it with cerium oxide (CeO₂). In this study, firstly, SPC was modified by phytic acid. Then, the CeO₂ was deposited on modified SPC using the self-assembly method. Catalyzed cerium (III) nitrate hexahydrate (CeH₃NO₄) was treated with alkali and calcined at 600 °C under nitrogen. XRD, XPS, SEM, EDS, UV-VIS /DRS, FTIR, PL and N₂ adsorption-desorption methods were used to characterize the crystal structure, chemical composition, morphology, surface physical and chemical properties. The effects of catalyst dosage, monomer contrast, pH value and co-existing anions on TC oxidation degradation were investigated, and the reaction mechanism of a 600 Ce-SPC photocatalytic reaction system was discussed. The results show that the 600 Ce-SPC composite presents uneven gully morphology, which is similar to the natural "briquettes". The degradation efficiency of 600 Ce-SPC reached about 99% at 60 min under light irradiation when the optimal catalyst dosage and pH were 20 mg and 7. Meanwhile, the reusability of the 600 Ce-SPC samples showed good stability and catalytic activity after four cycles.

Facile synthesis and comparative study of the enhanced photocatalytic degradation of two selected dyes by TiO2-g-C3N4 composite

Photocatalysis is considered a useful technique employed for the dye degradation through solar light, visible or UV light irradiation. In this study, TiO₂, g-C₃N₄, and TiO₂-g-C₃N₄ nanocomposites were successfully synthesized and studied for their ability to degrade Rhodamine B (RhB) and Reactive Orange 16 (RO-16), when exposed to visible light. The analytical techniques including XRD, TEM, SEM, DRS, BET, XPS, and fluorescence spectroscopy were used to explore the characteristics of all the prepared semiconductors. The photocatalytic performance of synthesized materials has been tested against both the selected dyes, and various experimental parameters were studied. The experimental results demonstrate that, in comparison to other fabricated composites, the TiO₂-g-C₃N₄ composite with the optimal weight ratio of g-C₃N₄ (15 wt%) to TiO₂ has shown outstanding degrading efficiency against RhB (89.62%) and RO-16 (97.20%). The degradation experiments were carried out at optimal conditions such as a catalyst load of 0.07 g, a dye concentration of 50 ppm, and a temperature of 50 ℃ at neutral pH in 90 min. In comparison to pure TiO₂ and g-C₃N₄, the TiO₂-g-C₃N₄, a semiconductor, has shown higher degradation efficiency due to its large surface area and decreased electron-hole recombination. The scavenger study gave an idea about the primary active species (^-OH radicals), responsible for dye degradation. The reusability of TiO₂-g-C₃N₄ was also examined in order to assess the composite sustainability.

Noble metal-free doped graphitic carbon nitride (g-C3N4) for efficient photodegradation of antibiotics: progress, limitations, and future directions

Graphitic carbon nitride (g-C₃N₄) is well recognised as one of the most promising materials for photocatalytic activities such as environmental remediation via organic pollution elimination. New methods of nanoscale structure design introduce tunable electrical characteristics and broaden their use as visible light-induced photocatalysts. This paper summarises the most recent developments in the design of g-C₃N₄ with element doping. Various methods of introducing metal and nonmetal elements into g-C₃N₄ have been investigated in order to simultaneously tune the material's textural and electronic properties to improve its response to the entire visible light range, facilitate charge separation, and extend charge carrier lifetime. The degradation of antibiotics is one of the application domains of such doped g-C₃N₄. We expect that this research will provide fresh insights into clear design methods for efficient photocatalysts that will solve environmental challenges in a sustainable manner. Finally, the problems and potential associated with g-C₃N₄-based nanomaterials are discussed. This review is expected to encourage the ongoing development of g-C₃N₄-based materials for greater efficiency in photocatalytic antibiotic degradation.

Facile fabrication of a 2D/2D CoFe-LDH/g-C3N4 nanocomposite with enhanced photocatalytic tetracycline degradation

The widespread use of tetracycline (TC) in medicine and agriculture has caused severe pollution problems in the environment. In this work, a nanocomposite comprising of CoFe-layered double hydroxides grown on graphitic carbon nitride nanosheets (CoFe-LDH/g-C₃N₄) with a notable two-dimensional/two-dimensional (2D/2D) heterostructure was synthesized through a facile co-precipitation method. The CoFe-LDH/g-C₃N₄ nanocomposite displayed significantly improved visible-light-driven photocatalytic activity towards TC degradation, compared to pristine g-C₃N₄ and CoFe-LDH alone. The enhanced activation efficiency was a result of intimate interfacial contact, enlarged the surface area, broadened visible-light absorbance, and enhanced photogenerated electron transfer. The scavenging experiments showed that holes (h⁺) and superoxide radical anions (‧O₂^-) played a crucial role in TC degradation. Factors including the type of TCs, initial concentration of TC, presence of ions, and the type of water matrix were investigated to evaluate the practical feasibility of the nanocomposites for TC removal from antibiotics-contaminated water. The repeated tests showed that the nanocomposites possessed good stability and recyclability. This study demonstrated the feasibility of achieving photocatalytic activity enhancement of g-C₃N₄ through the formation of a 2D-2D heterostructure between LDHs and g-C₃N₄.

Synthesis and characterisation of transition metal sulphide-loaded fly ash-based mesoporous EU-12 photocatalysts for degradation of rhodamine B

Transition metal sulphide-loaded fly ash-based EU-12 photocatalysts were synthesized by sono-hydrothermal method followed by ion exchange. The composites were characterized by XRD, FESEM, DSC-TGA, Raman spectroscopy, and BET surface area analysis. The XRD results imply 76.39% crystallinity of EU-12 and morphological studies by FESEM, and TEM revealed the shape and size of EU-12, i.e. rod-shaped with size ranging from 5 to 200 nm. Band gap of all synthesized photocatalysts were found to be ≤ 3.44 eV. The photoactivities of the photocatalysts were examined by degrading rhodamine B (RhB). The results indicated that metal sulphide/EU-12 composite had the strong photoactivity under visible light compared to dark environment. Furthermore, the efficiency of photocatalysts was determined in terms of degradation efficiency towards RhB which was found to be maximum of 98.62% for 0.2 M CdS/EU-12 at 2 gL^-1 of catalyst dosage and 10 ppm of dye concentration within 3 h under visible light source of 200 W.