Anionic polymerization of styrene and butadiene initiated by n-butyllithium in ethylbenzene: Determination of the propagation rate constants using Raman spectroscopy and gel permeation chromatography

Enzyme Degassing for Oxygen-Sensitive Reactions in Open Vessels of an Automated Parallel Synthesizer: RAFT Polymerizations

An enzyme degassing method for oxygen-intolerant polymerizations was implemented in a commercially available automated parallel synthesizer and tested for reversible addition-fragmentation chain transfer (RAFT) polymerizations performed in open vessels. For this purpose, a recently reported methodology that employs the enzyme glucose oxidase (GOx) to deplete oxygen in reaction media was utilized. The effectiveness of this approach to perform unattended parallel polymerization reactions in open vessels was demonstrated by comparing experimental results to those obtained under similar experimental conditions but utilizing the common degassing method of sparging N₂ to remove oxygen. The proposed experimental technique displayed good precision in performing RAFT polymerizations and good control of the obtained polymers and could be easily adapted to other systems where the removal of oxygen is mandatory. This alternative high-throughput/high-output method may have the potential to increase productivity in research projects where oxygen-intolerant reactions are involved.

The Mechanism of the Propagation in the Anionic Polymerization of Polystyryllithium in Non-Polar Solvents Elucidated by Density Functional Theory Calculations. A Study of the Negligible Part Played by Dimeric Ion-Pairs under Usual Polymerization Conditions

The elementary processes occurring in the anionic polymerization of styrene with dimerically associated polystyryllithium (propagation during the anionic polymerization of dimeric polystyryllithium) in the gas phase and cyclohexane were studied using MX062X/6-31+G(d), a recently developed density functional theory (DFT) method and compared with the polymerization of styrene with non-associated polystyryllithium, which was described in a previous study. The most stable transition state in the reaction of styrene with dimeric polystyryllithium has a structure in which the side chains of styrene and the two chain end units of polystyryllithium are located in the same direction around the Li atom near the reactive site. The relative enthalpy for this transition state in cyclohexane is 28 kJ·mol⁻¹, which is much lower than that for the reaction of non-associated polystyryllithium (51 kJ·mol⁻¹). However, the relative free energy (which determines the rate constant) for the former is 93 kJ·mol⁻¹, which is greater than that for the latter by 7 kJ·mol⁻¹, indicating that the latter reaction (reaction with non-associated polystyryllithium) is advantageous over the former (reaction with dimeric polystyrylllithium). Their rates of reaction are also affected by initiator concentrations; in the case of reactions with low initiator concentrations, from which high molecular weight polymers are usually obtained, the rate of reaction corresponding to non-associated polystyryllithium is much larger than that corresponding to dimeric polystyryllithium.

New Vistas on the Anionic Polymerization of Styrene in Non-Polar Solvents by Means of Density Functional Theory

The elementary processes of anionic styrene polymerization in the gas phase and in cyclohexane were studied using M062X (a recently developed density functional theory (DFT) method) combined with the 6-31+G(d) basis sets, in order to clarify the complicated phenomena caused by the association of the active chain-ends and elucidate the details of the polymerization mechanism. Three types of HSt₂Li (a model structure of polystyryllithium chain-ends) were obtained; the well-known first structure in which Li is coordinated to the side chain, the second structure in which Li is coordinated to the phenyl ring, (both without the penultimate unit coordination), and the third structure in which Li is coordinated to both the chain-end unit and the penultimate styrene unit. Although the third HSt₂Li is the most stable as expected, the free energy for the transition state of its reaction with styrene is higher than those for the other two transition states due to its steric hindrance. The free energy for the transition state of the reaction of the second HSt₂Li with styrene is the lowest, suggesting that the route through it is the predominant reaction path. The penultimate unit effect, slower addition of styrene to HSt₂Li than to HStLi, is attributed to coordination of the penultimate styrene units of the polystyryllithium dimer (one of the starting materials) to its Li atoms. The calculated enthalpy for the reaction barrier of the second HSt₂Li with styrene in cyclohexane was found to agree with the observed apparent activation energy in benzene.