Effects of nonuniform insonation by catheter-tipped Doppler transducers on velocity estimation

Numerical assessment of the impact of a flow wire on its velocity measurements

Blood flow velocities can be measured using a Doppler flow wire. This numerical study evaluates the impact of a 0.014" flow wire on the measured frequencies in a straight artery with diameters of 3 mm and 4 mm, under steady and pulsatile flow conditions. Simulations were performed with the wires positioned differently in the artery (perfectly centred and at an offset of 0.5 mm from the wall) and with different types of wire (tilted and straight). Measurements were taken at range gates from 4 mm to 10 mm. During simulations using a 3-mm vessel under pulsatile flow conditions, the relative error between the measured and reference maximum frequency (occurring in absence of the wire) decreased from 17.7% to 11.6% (with a mean value of 14.9%). During simulations using an off-centre 1.5 degree tilted wire, the mean error was approximately 5%. Therefore, our study suggests that that a centrally positioned flow wire is unfavourable for measuring flow velocities.

Doppler colour flow imaging and flow quantification with a novel forward-viewing intravascular ultrasound system

The aim of this work was to investigate the potential of a novel forward-viewing intravascular ultrasound (IVUS) system for flow quantification and colour flow imaging combined with B-mode imaging. A stiff 3.8-mm diameter catheter was used to scan a 72 degrees sector ahead of its tip. Operating at 30 MHz, the catheter was integrated with an IVUS scanner and a radiofrequency (RF) data-acquisition system. RF data were software processed for producing B-mode images and deriving velocity estimates. Steady flow in the range of 45 to 146 mL/min toward the catheter, was used in wall-less tissue-mimicking phantoms simulating healthy lumen (8-mm diameter), 30% diameter symmetrical stenosis and 37% diameter eccentric stenosis. The system provided colour flow images and good estimation of peak velocity and volumetric flows (within 1% to 9% and 16% to 48%, respectively, of calculated values) at 5 to 7 mm distal to the catheter. A sector forward-viewing IVUS imaging/Doppler system is suitable for combined anatomical and functional assessment of stenosed vessels.

In vitro validation of volumetric blood flow measurement using Doppler flow wire

Determination of any volumetric blood flow requires assessment of mean blood flow velocity and vessel cross-sectional area. For evaluation of coronary blood flow and flow reserve, however, assessment of average peak velocity alone is widely used, but changes in velocity profile and vessel area are not taken into account. We studied the feasibility of a new method for calculation of volumetric blood flow by Doppler power using a Doppler flow wire. An in vitro model with serially connected silicone tubes of known lumen diameters (1.5, 2.0, 2.5, 3.0, 3.5 and 4.0 mm) and pulsatile blood flow ranging from 10 to 200 mL/min was used. A Doppler flow wire was connected to a commercially available Doppler system (FloMap(R), Cardiometrics) for online calculation of the zeroth (M(0)) and the first (M(1)) Doppler moment, as well as mean flow velocity (V(m)). Two different groups of sample volumes (at different gate depths) were used: 1. two proximal sample volumes lying completely within the vessel were required to evaluate the effect of scattering and attenuation on Doppler power, and 2. distal sample volumes intersecting completely the vessel lumen to assess the vessel cross-sectional area. Area (using M(0)) and V(m) (using M(1)/M(0)) obtained from the distal gates were corrected for scattering and attenuation by the data obtained from the proximal gates, allowing calculation of absolute volumetric flow. These results were compared to the respective time collected flow. Correlation between time collected and Doppler-derived flow measurements was 0.98 (p < 0.0001), with a regression line close to the line of equality indicating an excellent agreement of the two measurements in each individual tube. The mean paired flow difference between the two techniques was 1.5 +/- 9.0 mL/min (ns). Direct volumetric blood flow measurement from received Doppler power using a Doppler flow wire system is feasible. This technique may potentially be of great clinical value because it allows an accurate assessment of coronary flow and flow reserve with a commercially available flow wire system.

Developments in cardiovascular ultrasound. Part 2: Arterial applications

Many of the changes resulting from arterial disease can be measured, using Doppler ultrasound for measurement of blood velocity and B-scan imaging for measurement of tissue structure and composition. Wall thickness, the degree of arterial narrowing and plaque volume can be measured using B-scan imaging, and 3D ultrasound can be used to improve the accuracy of measurements of plaque volume and for improved visualisation of complex arterial geometries. Measurement of the dynamic properties of the arterial wall permits estimation of wall elasticity and plaque motion. From the Doppler signal, measurements of blood velocity are used to estimate the degree of arterial narrowing and volumetric flow, although measurement errors can be large. Wall shear stress can be estimated by measuring the velocity gradient at the vessel wall. The problems of inadequate spatial resolution and interference from overlying tissue are largely removed when intravascular systems are used, and these have superior capability in the assessment of arterial structure and tissue composition. However, measurement of quantities relating to blood flow is more difficult using the intravascular approach, as the indwelling cather disturbs the blood flow pattern, and currently, assessment of flow and vessel cross-section are not performed at the same site.