Mechanical properties of nanophase metals

Role of Biomaterials Used for Periodontal Tissue Regeneration-A Concise Evidence-Based Review

Periodontal infections are noncommunicable chronic inflammatory diseases of multifactorial origin that can induce destruction of both soft and hard tissues of the periodontium. The standard remedial modalities for periodontal regeneration include nonsurgical followed by surgical therapy with the adjunctive use of various biomaterials to achieve restoration of the lost tissues. Lately, there has been substantial development in the field of biomaterial, which includes the sole or combined use of osseous grafts, barrier membranes, growth factors and autogenic substitutes to achieve tissue and bone regeneration. Of these, bone replacement grafts have been widely explored for their osteogenic potential with varied outcomes. Osseous grafts are derived from either human, bovine or synthetic sources. Though the biologic response from autogenic biomaterials may be better, the use of bone replacement synthetic substitutes could be practical for clinical practice. This comprehensive review focuses initially on bone graft replacement substitutes, namely ceramic-based (calcium phosphate derivatives, bioactive glass) and autologous platelet concentrates, which assist in alveolar bone regeneration. Further literature compilations emphasize the innovations of biomaterials used as bone substitutes, barrier membranes and complex scaffold fabrication techniques that can mimic the histologically vital tissues required for the regeneration of periodontal apparatus.

Ultra-dense dislocations stabilized in high entropy oxide ceramics

Dislocations are commonly present and important in metals but their effects have not been fully recognized in oxide ceramics. The large strain energy raised by the rigid ionic/covalent bonding in oxide ceramics leads to dislocations with low density (∼10⁶ mm⁻²), thermodynamic instability and spatial inhomogeneity. In this paper, we report ultrahigh density (∼10⁹ mm⁻²) of edge dislocations that are uniformly distributed in oxide ceramics with large compositional complexity. We demonstrate the dislocations are progressively and thermodynamically stabilized with increasing complexity of the composition, in which the entropy gain can compensate the strain energy of dislocations. We also find cracks are deflected and bridged with ∼70% enhancement of fracture toughness in the pyrochlore ceramics with multiple valence cations, due to the interaction with enlarged strain field around the immobile dislocations. This research provides a controllable approach to establish ultra-dense dislocations in oxide ceramics, which may open up another dimension to tune their properties.

Dislocation engineering is important for designing structural materials. Here the authors demonstrate that a high-entropy oxide ceramic with a high density of edge dislocations can be stabilized by increasing the compositional complexity, resulting in enhanced fracture toughness.

Effect of Nitrogen Partial Pressure on the Structural, Mechanical, and Electrical Properties of (CrHfNbTaTiVZr)N Coatings Deposited by Reactive Magnetron Sputtering

Multi-element (CrHfNbTaTiVZr)N coatings were prepared through the magnetron sputtering of an equimolar CrHfNbTaTiVZr alloy target. This study determined the influences of N2-to-total (N2 + Ar) ratios (RN) on the composition, structure, mechanical properties, and electrical performance of the coatings. Coating thickness decreased from 898 nm to 128 nm with increasing RN from 0% to 100%. The alloy coating has bundles of fibrous structures with remarkable void boundaries. The coating changed from amorphous phase to face-centered cubic (FCC) phase with (111) preferred orientation, then to FCC phase with (200) preferred orientation, and finally to near-amorphous phase as RN increased from 0% to 100%. The microstructure of the nitride coatings transformed from a columnar structure with rough faceted tops and void boundaries into a dense and small structure with smooth domed tops. The grain size of the nitride coatings also decreased with RN. Accordingly, the electrical performance at high RN was poor. The nitride coating deposited at RN = 60% had the highest hardness of 16.6 GPa and the lowest friction coefficient of 0.52, owing to structural densification and grain refinement.

Surface Roughness of Dental Implant and Osseointegration

INTRODUCTION

Dental implants are a usual treatment for the loss of teeth. The success of this therapy is due to the predictability, safety and longevity of the bone-implant interface. Dental implant surface characteristics like roughness, chemical constitution, and mechanical factors can contribute to the early osseointegration. The aim of the present article is to perform a review of the literature on surface roughness of dental implant and osseointegration.

METHODOLOGY

This work is a narrative review of some aspects of surface roughness of dental implant and osseointegration.

CONCLUSION

Despite technological advancement in the biomaterials field, the ideal surface roughness for osseointegration still remains unclear. In this study about surface nanoroughness of dental implant and osseointegration, the clinical relevance is yet unknown. Innovative findings on nanoroughness are valuable in the fields of dental implantology, maxillofacial or orthopedic implant surfaces and also on cardiovascular implants in permanent contact with patient's blood.

Preparing bulk ultrafine-microstructure high-entropy alloys via direct solidification

In the past three decades, nanostructured (NS) and ultrafine-microstructure (UFM) materials have received extensive attention due to their excellent mechanical properties such as high strength. However, preparing low-cost and bulk NS and UFM materials remains to be a challenge, which limits their industrial applications. Here, we report a new strategy to prepare bulk UFM alloys via the direct solidification of high-entropy alloys (HEAs). As a proof of concept, we designed AlCoCr_xFeNi (1.8 ≤ x ≤ 2.0) HEAs and achieved a complete UFM in bulk materials. The compositional requirements for obtaining the formation of the UFM are highly demanding, necessitating the coupling of near eutectic alloy composition and the high temperature decomposition of supersaturated primary and secondary phases. Our strategy provides a low-cost and highly efficient method to prepare bulk UFM alloys, with great potential to accelerate the engineering application of these materials.

Building Materials from Colloidal Nanocrystal Arrays: Preventing Crack Formation during Ligand Removal by Controlling Structure and Solvation

Crack-free, ligand-free, phase-pure nanostructured solids, using colloidal nanocrystals as precursors, are fabricated by a scalable and facile approach. Films produced by this approach have conductivities comparable to those of bulk crystals over more than 1 cm (1.370 S cm^-1 for PbS films).

Techniques for dental implant nanosurface modifications

PURPOSE

Dental implant has gained clinical success over last decade with the major drawback related to osseointegration as properties of metal (Titanium) are different from human bone. Currently implant procedures include endosseous type of dental implants with nanoscale surface characteristics. The objective of this review article is to summarize the role of nanotopography on titanium dental implant surfaces in order to improve osseointegration and various techniques that can generate nanoscale topographic features to titanium implants.

MATERIALS AND METHODS

A systematic electronic search of English language peer reviewed dental literature was performed for articles published between December 1987 to January 2012. Search was conducted in Medline, PubMed and Google scholar supplemented by hand searching of selected journals. 101 articles were assigned to full text analysis. Articles were selected according to inclusion and exclusion criterion. All articles were screened according to inclusion standard. 39 articles were included in the analysis.

RESULTS

Out of 39 studies, seven studies demonstrated that bone implant contact increases with increase in surface roughness. Five studies showed comparative evaluation of techniques producing microtopography and nanotopography. Eight studies concluded that osteoblasts preferably adhere to nano structure as compared to smooth surface. Six studies illustrated that nanotopography modify implant surface and their properties. Thirteen studies described techniques to produce nano roughness.

CONCLUSION

Modification of dental osseous implants at nanoscale level produced by various techniques can alter biological responses that may improve osseointegration and dental implant procedures.

Systematic study on the electronic structure and mechanical properties of X2BC (X = Mo, Ti, V, Zr, Nb, Hf, Ta and W)

In this work the electronic structure and mechanical properties of the phases X(2)BC with X =Ti, V, Zr, Nb, Mo, Hf, Ta, W (Mo(2)BC-prototype) were studied using ab initio calculations. As the valence electron concentration (VEC) per atom is increased by substitution of the transition metal X, the six very strong bonds between the transition metal and the carbon shift to lower energies relative to the Fermi level, thereby increasing the bulk modulus to values of up to 350 GPa, which corresponds to 93% of the value reported for c-BN. Systems with higher VEC appear to be ductile as inferred from both the more positive Cauchy pressure and the larger value of the bulk to shear modulus ratio (B/G). The more ductile behavior is a result of the more delocalized interatomic interactions due to larger orbital overlap in smaller unit cells. The calculated phase stabilities show an increasing trend as the VEC is decreased. This rather unusual combination of high stiffness and moderate ductility renders X(2)BC compounds with X = Ta, Mo and W as promising candidates for protection of cutting and forming tools.

Nanocomposites nc-TiN/a-Si3N4/a- and nc-TiSi2 with Hardness Exceeding 100 GPa and High Fracture Toughness

In course of further development of our generic concept for the design of novel superhard nanocomposites [1,2] we have recently developed new multi-phase ultrahard nano-composite coatings with Vickers mirohardness of 80 to 105 GPa which is in the range of natural diamond. The coatings show a high elastic recovery of up to 90% upon a relatively large indentation deformation. The hardness measured by the depth sensing technique agree with those calculated from the area of the remaining pseudoplastic deformation. The very high apparent fracture toughness is illustrated by the absence of any radial cracks upon in-dentation with a large load of I N into 10.3 p.m thick film [3]. The unusual combination of high hardness, elastic recovery and apparent fracture toughness was attributed to the ample possibility of cracks deflection, meandering and termination during loading and cracks closure upon unloading [1,2,4]. The suggested nanostructure of the coatings has been elucidated on a basis of a complex analysis by means XRD, EDX, ERD, XPS and HR TEM.

Grain Size Dependent Mechanical Properties in Nanophase Materials

It has become possible in recent years to synthesize metals and ceramics under well controlled conditions with constituent grain structures on a nanometer size scale (below 100 nm). These new materials have mechanical properties that are strongly grain-size dependent and often significantly different than those of their coarser grained counterparts. Nanophase metals tend to become stronger and ceramics are more easily deformed as grain size is reduced. The observed mechanical property changes appear to be related primarily to grain size limitations and the large percentage of atoms in grain boundary environments. A brief overview of our present knowledge about the grain-size dependent mechanical properties of nanophase materials is presented.

Effects of Crystalline Anisotropy and Indenter Size on Nanoindentation by Multiscale Simulation

Nanoindentation processes in single crystal Ag thin film under different crystallographic orientations and various indenter widths are simulated by the quasicontinuum method. The nanoindentation deformation processes under influences of crystalline anisotropy and indenter size are investigated about hardness, load distribution, critical load for first dislocation emission and strain energy under the indenter. The simulation results are compared with previous experimental results and Rice-Thomson (R-T) dislocation model solution. It is shown that entirely different dislocation activities are presented under the effect of crystalline anisotropy during nanoindentation. The sharp load drops in the load-displacement curves are caused by the different dislocation activities. Both crystalline anisotropy and indenter size are found to have distinct effect on hardness, contact stress distribution, critical load for first dislocation emission and strain energy under the indenter. The above quantities are decreased at the indenter into Ag thin film along the crystal orientation with more favorable slip directions that easy trigger slip systems; whereas those will increase at the indenter into Ag thin film along the crystal orientation with less or without favorable slip directions that hard trigger slip systems. The results are shown to be in good agreement with experimental results and R-T dislocation model solution.

Extended x-ray absorption fine structure studies of the atomic structure of nanoparticles in different metallic matrices

It has been appreciated for some time that the novel properties of particles in the size range 1-10 nm are potentially exploitable in a range of applications. In order to ultimately produce commercial devices containing nanosized particles, it is necessary to develop controllable means of incorporating them into macroscopic samples. One way of doing this is to embed the nanoparticles in a matrix of a different material, by co-deposition for example, to form a nanocomposite film. The atomic structure of the embedded particles can be strongly influenced by the matrix. Since some of the key properties of materials, including magnetism, strongly depend on atomic structure, the ability to determine atomic structure in embedded nanoparticles is very important. This review focuses on nanoparticles, in particular magnetic nanoparticles, embedded in different metal matrices. Extended x-ray absorption fine structure (EXAFS) provides an excellent means of probing atomic structure in nanocomposite materials, and an overview of this technique is given. Its application in probing catalytic metal clusters is described briefly, before giving an account of the use of EXAFS in determining atomic structure in magnetic nanocomposite films. In particular, we focus on cluster-assembled films comprised of Fe and Co nanosized particles embedded in various metal matrices, and show how the crystal structure of the particles can be changed by appropriate choice of the matrix material. The work discussed here demonstrates that combining the results of structural and magnetic measurements, as well as theoretical calculations, can play a significant part in tailoring the properties of new magnetic cluster-assembled materials.

Nanostructured biomaterials for tissue engineering bone

Advances in several critical research fields (processing, catalytic, optical, actuation, electrical, mechanical, etc.) have started to benefit from nanotechnology. Nano-technology can be broadly defined as the use of materials and systems whose structures and components exhibit novel and significantly changed properties when control is gained at the atomic, molecular, and supramolecular levels. Specifically, such advances have been found for materials when particulate size is decreased to below 100 nm. However, to date, relatively few advantages have been described for biological applications (specifically, those involving bone tissue engineering). This chapter elucidates several promising examples of how nanophase materials can be used to improve orthopedic implant applications. These include mechanical advantages as well as altered cell functions, leading to increased bone tissue regeneration on a wide range of nanophase materials including ceramics, polymers, metals, and composites thereof. Such advances were previously unimaginable with conventional materials possessing large micron-sized particulates.

Enhanced functions of vascular and bladder cells on poly-lactic-co-glycolic acid polymers with nanostructured surfaces

Polymers currently utilized for tissue engineering applications do not possess surfaces with nanostructured features. However, the tissue that the polymers will replace is composed of proteins that have nanometer dimensions. Undoubtedly, in situ, cells are accustomed to interacting with surface roughness values in the nanometer regime due to the presence of such proteins in natural tissue. Therefore, the objective of this paper was to design, synthesize and evaluate (using in vitro cellular models) poly-lactic-co-glycolic acid (PLGA) with nanostructured surface features to serve as the next generation of more efficient tissue engineered materials. For this purpose, nanostructured PLGA was created by treating conventional PLGA with various concentrations of NaOH for select periods of time. To eliminate surface chemistry changes created though the etching process, PLGA was cast from silastic molds of NaOH-treated nanostructured PLGA. Results provided the first evidence of increased numbers of vascular cells (specifically, endothelial and aortic smooth muscle cells) and bladder smooth muscle cells on nanostructured compared with conventional PLGA substrates. For this reason, the present results suggest, for the first time, that PLGA should incorporate a high degree of nanostructured surface roughness to enhance tissue regeneration for vascular and bladder applications.

Adhesion of Pseudomonas fluorescens onto nanophase materials

Nanobiotechnology is a growing area of research, primarily due to the potentially numerous applications of new synthetic nanomaterials in engineering/science. Although various definitions have been given for the word 'nanomaterials' by many different experts, the commonly accepted one refers to nanomaterials as those materials which possess grains, particles, fibres, or other constituent components that have one dimension specifically less than 100 nm. In biological applications, most of the research to date has focused on the interactions between mammalian cells and synthetic nanophase surfaces for the creation of better tissue engineering materials. Although mammalian cells have shown a definite positive response to nanophase materials, information on bacterial interactions with nanophase materials remains elusive. For this reason, this study was designed to assess the adhesion of Pseudomonas fluorescens on nanophase compared to conventional grain size alumina substrates. Results provide the first evidence of increased adhesion of Pseudomonas fluorescens on alumina with nanometre compared to conventional grain sizes. To understand more about the process, polymer (specifically, poly-lactic-co-glycolic acid or PLGA) casts were made of the conventional and nanostructured alumina surfaces. Results showed similar increased Pseudomonas fluorescens capture on PLGA casts of nanostructured compared to conventional alumina as on the alumina itself. For these reasons, a key material property shown to enhance bacterial adhesion was elucidated in this study for both polymers and ceramics: nanostructured surface features.

Increased osteoblast function on PLGA composites containing nanophase titania

Nanotechnology creates materials that potentially outperform, at several boundaries, existing materials in terms of mechanical, electrical, catalytic, and optical properties. However, despite their promise to mimic the surface roughness cells experience in vivo, the use of nanophase materials in biological applications remains to date largely unexplored. The objective of the present in vitro study was, therefore, to determine whether when added to a polymer scaffold, nanophase compared to conventional ceramics enhance functions of osteoblasts (or bone-forming cells). Results from this study provided the first evidence that functions (specifically, adhesion, synthesis of alkaline phosphatase, and deposition of calcium-containing mineral) of osteoblasts increased on poly-lactic-co-glycolic acid (PLGA) scaffolds containing nanophase compared to conventional grain size titania with greater weight percentage (from 10-30 wt %). Because the chemistry, material phase, porosity (%), and pore size of the composites were similar, this study implies that the surface features created by adding nanophase compared to conventional titania was a key parameter that enhanced functions of osteoblasts. In this manner, the study adds another novel property of nanophase ceramics: their ability to promote osteoblast functions in vitro when added to a polymer scaffold. For this reason, nanophase ceramics (and nanomaterials in general) deserve further attention as orthopedic tissue engineering materials.

Phase transitions of hydroxyapatite coatings during post-heat treatment and their performances under ultrasonic tests

Highly or completely crystalline hydroxyapatite (HA) coatings can be obtained by post-heat treatment. We have developed a high-temperature (490 degrees C) and a low-temperature (125 degrees C) heat treatment to improve the crystallinity of HA coatings. Both methods transform entirely the amorphous phase into crystalline HA. However, the microstructure of the coating is dependent on the post-heating method. Nanocrystalline HA is about half of the component of the low-temperature heated coating while highly crystalline HA dominates the high-temperature heated coating, as detected by X-ray diffraction. The effects of both methods on the disintegration of the coatings were tested by ultrasonic treatment. The high-temperature heated coatings exhibited poor integrity while the low-temperature heated coatings exhibited better integrity, possibly due to their different microstructure. SEM revealed that the coatings disintegrated via different mechanisms: the high-temperature heated coatings failed via crack initiation and propagation while the low-temperature heated coatings failed via pit formation and subsequent widening.