Spinel Mixed Oxides for Chemical-Loop Reforming: From Solid State to Potential Application

Photoelectrochemical water oxidation over TiO2 nanotubes modified with MoS2 and g-C3N4

TiO₂ nanotube arrays (TNAs) have been studied for photoelectrochemical (PEC) water splitting. However, there are two major barriers of TNAs, including a low photo-response and the fast charge carrier recombination in TNAs, leading to poor photocatalytic efficiency. Through a comparison of MoS₂/TNAs and g-C₃N₄/TNAs, it was found that TNAs modified with MoS₂ and g-C₃N₄ exhibited a current density of, respectively, 210.6 and 139.6 μA·cm^-2 at an overpotential of 1.23 V vs RHE, which is 18.2 and 12 times higher than that of pure TNAs under the same conditions. The stability of the MoS₂/TNAs heterojunction is higher than that of g-C₃N₄/TNAs.

Understanding the Behavior of Dicalcium Ferrite (Ca2Fe2O5) in Chemical Looping Syngas Production from CH4

Previous work on calcium ferrites showed they were able to convert syngas to hydrogen via chemical looping. The mixture of iron and calcium and their oxides has different thermodynamic properties than iron oxide alone. Here, the use of methane, an abundant fuel, is investigated as the reductant in chemical looping syngas production. In contrast to syngas-fueled cycles, the looping materials became more active with cycling using methane as the fuel. When reduced by methane, the looping material often showed a significant induction period, indicating that products of reduction (in particular metallic Fe) acted as a catalyst for further reduction. The behavior in a thermogravimetric analyzer (TGA) and a fluidized bed was comparable, i.e., no degradation with cycling. The reduced C₂F appeared to be easily reformed when oxidized with CO₂, and there was little evidence of bulk phase segregation. The improved kinetics on cycling was likely due to the separation of metallic Fe onto the surface. Using hydrogen to partially reduce C₂F promotes the catalytic pyrolysis of methane.

Transition Metal Dichalcogenides [MX2] in Photocatalytic Water Splitting

The quest for a clean, renewable and sustainable energy future has been highly sought for by the scientific community over the last four decades. Photocatalytic water splitting is a very promising technology to proffer a solution to present day environmental pollution and energy crises by generating hydrogen fuel through a “green route” without environmental pollution. Transition metal dichalcogenides (TMDCs) have outstanding properties which make them show great potential as effective co-catalysts with photocatalytic materials such as TiO2, ZnO and CdS for photocatalytic water splitting. Integration of TMDCs with a photocatalyst such as TiO2 provides novel nanohybrid composite materials with outstanding characteristics. In this review, we present the current state of research in the application of TMDCs in photocatalytic water splitting. Three main aspects which consider their properties, advances in the synthesis routes of layered TMDCs and their composites as well as their photocatalytic performances in the water splitting reaction are discussed. Finally, we raise some challenges and perspectives in their future application as materials for water-splitting photocatalysts.

Porous Silicon Carbide (SiC): A Chance for Improving Catalysts or Just Another Active-Phase Carrier?

There is an obvious gap between efforts dedicated to the control of chemicophysical and morphological properties of catalyst active phases and the attention paid to the search of new materials to be employed as functional carriers in the upgrading of heterogeneous catalysts. Economic constraints and common habits in preparing heterogeneous catalysts have narrowed the selection of active-phase carriers to a handful of materials: oxide-based ceramics (e.g. Al₂O₃, SiO₂, TiO₂, and aluminosilicates-zeolites) and carbon. However, these carriers occasionally face chemicophysical constraints that limit their application in catalysis. For instance, oxides are easily corroded by acids or bases, and carbon is not resistant to oxidation. Therefore, these carriers cannot be recycled. Moreover, the poor thermal conductivity of metal oxide carriers often translates into permanent alterations of the catalyst active sites (i.e. metal active-phase sintering) that compromise the catalyst performance and its lifetime on run. Therefore, the development of new carriers for the design and synthesis of advanced functional catalytic materials and processes is an urgent priority for the heterogeneous catalysis of the future. Silicon carbide (SiC) is a non-oxide semiconductor with unique chemicophysical properties that make it highly attractive in several branches of catalysis. Accordingly, the past decade has witnessed a large increase of reports dedicated to the design of SiC-based catalysts, also in light of a steadily growing portfolio of porous SiC materials covering a wide range of well-controlled pore structure and surface properties. This review article provides a comprehensive overview on the synthesis and use of macro/mesoporous SiC materials in catalysis, stressing their unique features for the design of efficient, cost-effective, and easy to scale-up heterogeneous catalysts, outlining their success where other and more classical oxide-based supports failed. All applications of SiC in catalysis will be reviewed from the perspective of a given chemical reaction, highlighting all improvements rising from the use of SiC in terms of activity, selectivity, and process sustainability. We feel that the experienced viewpoint of SiC-based catalyst producers and end users (these authors) and their critical presentation of a comprehensive overview on the applications of SiC in catalysis will help the readership to create its own opinion on the central role of SiC for the future of heterogeneous catalysis.

Graphene-based Membranes for H2 Separation: Recent Progress and Future Perspective

Hydrogen (H2) is an industrial gas that has showcased its importance in several well-known processes such as ammonia, methanol and steel productions, as well as in petrochemical industries. Besides, there is a growing interest in H2 production and purification owing to the global efforts to minimize the emission of greenhouse gases. Nevertheless, H2 which is produced synthetically is expected to contain other impurities and unreacted substituents (e.g., carbon dioxide, CO2; nitrogen, N2 and methane, CH4), such that subsequent purification steps are typically required for practical applications. In this context, membrane-based separation has attracted a vast amount of interest due to its desirable advantages over conventional separation processes, such as the ease of operation, low energy consumption and small plant footprint. Efforts have also been made for the development of high-performance membranes that can overcome the limitations of conventional polymer membranes. In particular, the studies on graphene-based membranes have been actively conducted most recently, showcasing outstanding H2-separation performances. This review focuses on the recent progress and potential challenges in graphene-based membranes for H2 purification.