Liquid-phase microextraction with in-drop derivatization combined with microvolume fluorospectrometry for free and hydrolyzed formaldehyde determination in textile samples

Direct immersion single-drop microextraction combined with fluorescence detection using an optical probe. Application for highly sensitive determination of rhodamine 6G

The use of an optical probe for fluorescence detection combined with direct immersion single-drop microextraction has been demonstrated as an innovative approach. The optical probe served both as a drop holder for extractant and as a measuring device which made it possible to eliminate the use of cuvettes. A laser and a light emitting diode (LED) were tested as possible light sources. Both of them showed comparable results. However, given the much smaller half-band width of the laser radiation, its use has proven to be preferable since background correction can be eliminated. Direct immersion single-drop microextraction of an ionic association complex of rhodamine 6G with picric acid with subsequent fluorescent detection (λex was 532 nm and 525 nm for laser and LED, respectively; λem was 560 nm for both laser and LED) was used a model system to evaluate the new approach. The extractant phase was a 55 μL amyl acetate microdrop fixed in the optical part of the probe. LOD, LOQ and linear calibration range were found as 0.14, 0.48 and 0.5-10 nmol L-1, and 0.15, 0.50 and 0.5-5 nmol L-1 for laser and LED light sources, respectively. The accuracy of the method was assessed by analyzing real water samples.

Deep Eutectic Solvent-Based Coating Sorbent for Preconcentration of Formaldehyde by Thin-Film Solid-Phase Microextraction Technique

A thin-film solid-phase microextraction method with a sorbent composed of a deep eutectic solvent was developed for the preconcentration of formaldehyde from river and lake water samples. Four new deep eutectic solvents (DESs) were synthesized, each in molar ratios 1:1, 1:2, and 1:3. Among prepared compounds, the greatest efficiency in the proposed method of preconcentration of formaldehyde derivatized with Nash reagent was demonstrated by DES-3 consisting of benzyldimethylhexadecylammonium chloride and lauric acid, in a molar ratio of 1:3. For the proposed method, the parameters affecting the extraction efficiency of formaldehyde were optimized (including the choice of DES-based sorbent and desorption solvent as well as the sample volume and pH, the salting-out effect, the extraction time, and the desorption time). Under optimal conditions, the proposed method achieved good precision between 3.3% (for single sorbent) and 4.8% (for sorbent-to-sorbent) as well as good recovery ranging from 78.0 to 99.1%. The limits of detection and quantitation were 0.15 ng mL−1 and 0.50 ng mL−1, respectively. The enrichment factor was equal to 178. The developed method was successfully applied to determine formaldehyde in environmental water samples.

Experimental design and machine learning strategies for parameters screening and optimization of Hantzsch condensation reaction for the assay of sodium alendronate in oral solution

An experimental design was adopted to attain the optimum reaction parameters of chemical derivatization of anhydrous sodium alendronate in an oral solution formulaviaHantzsch condensation reaction.

A Formaldehyde Gas Sensor Based on Zinc Doped Lanthanum Ferrite

The gas-sensing properties of zinc doped lanthanum ferrite (Zn-LaFeO3) compounds for formaldehyde were investigated in this paper. Zn-LaFeO3 powders were prepared using sol-gel method combined with microwave chemical synthesis. The powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The formaldehyde gas-sensing characteristics for the sample were examined. The experimental results indicate that the sensor based on the sample Zn-LaFeO3 shows excellent gas-sensing properties to formaldehyde gas. At the optimal operating temperature of 250°C, the sensitivity of the sensor based on LaFe0.7Zn0.3O3 to 100ppm formaldehyde is 38, while to other test gases, the sensitivity is all lower than 20. The response and recovery times for the sample to formaldehyde gas are 100s and 100s, respectively.

Ionic liquid-based dispersive liquid-liquid microextraction for the determination of formaldehyde in wastewaters and detergents

Spectrophotometry in combination with ionic liquid-based dispersive liquid-liquid microextraction (DLLME) was applied for the extraction and determination of formaldehyde in real samples. The method is based on the reaction of formaldehyde with methyl acetoacetate in the presence of ammonia. The variation in the absorbance of the reaction product was measured at 375 nm. An appropriate mixture of ethanol (disperser solvent) and ionic liquid, 1-hexyl-3-methylimidazoliumhexafluoro-phosphate [C(6)MIM][PF(6)] (extraction solvent) was rapidly injected into a water sample containing formaldehyde. After extraction, sedimented phase was analyzed by spectrophotometry. Under the optimum conditions, the calibration graph was linear in the range of 0.1-20 ng mL(-1) with the detection limit of 0.02 ng mL(-1) and limit of quantification of 0.08 ng mL(-1) for formaldehyde. The relative standard deviation (RSD%, n = 5) for the extraction and determination of 0.8 ng mL(-1) of formaldehyde in the aqueous samples was 2.5%. The results showed that DLLME is a very simple, rapid, sensitive, and efficient analytical method for the determination of trace amounts of formaldehyde in wastewaters and detergents, and suitable results were obtained.