Micro solid phase spectrophotometry in a sequential injection lab-on-valve platform for cadmium, zinc, and copper determination in freshwaters

Non-transferrin-bound iron determination in blood serum using microsequential injection solid phase spectrometry- proof of concept

Non-transferrin-bound iron (NTBI) is a group of circulating toxic iron forms, which occur in iron overload or health conditions with dysregulation of iron metabolism. NTBI is responsible for increased oxidative stress and tissue iron loading. Despite its relevance as a biochemical marker in several diseases, a standardized assay is still lacking. Several methods were developed to quantify NTBI, but results show high inter-method and even inter-laboratory variability. Thus, the development of a consistent NTBI assay is a major goal in the management of iron overload and related clinical conditions. In this work, a micro sequential injection lab-on-valve (μSI-LOV) method in a solid phase spectrophotometry (SPS) mode was developed for the quantification of NTBI, using a bidentate 3,4-hydroxypyridinone (3,4-HPO) ligand anchored to sepharose beads as a chromogenic reagent. To attain SPS, the functionalized beads were packed into a column in the flow cell, and the analyte, NTBI retained as iron (III), formed a colored complex at the beads while eliminating the sample matrix. The dynamic concentration range was 1.62-7.16 μmol L^-1 of iron (III), with a limit of detection of 0.49 μmol L^-1 and a limit of quantification of 1.62 μmol L^-1. The proposed μSI-LOV-SPS method is a contribution to the development of an automatic method for the quantification of the NTBI in serum samples.

Highly Sensitive Whole-Cell Biosensor for Cadmium Detection Based on a Negative Feedback Circuit

Although many whole-cell biosensors (WCBs) for the detection of Cd2+ have been developed over the years, most lack sensitivity and specificity. In this paper, we developed a Cd2+ WCB with a negative feedback amplifier in P. putida KT2440. Based on the slope of the linear detection curve as a measure of sensitivity, WCB with negative feedback amplifier greatly increased the output signal of the reporter mCherry, resulting in 33% greater sensitivity than in an equivalent WCB without the negative feedback circuit. Moreover, WCB with negative feedback amplifier exhibited increased Cd2+ tolerance and a lower detection limit of 0.1 nM, a remarkable 400-fold improvement compared to the WCB without the negative feedback circuit, which is significantly below the World Health Organization standard of 27 nM (0.003 mg/L) for cadmium in drinking water. Due to the superior amplification of the output signal, WCB with negative feedback amplifier can provide a detectable signal in a much shorter time, and a fast response is highly preferable for real field applications. In addition, the WCB with negative feedback amplifier showed an unusually high specificity for Cd2+ compared to other metal ions, giving signals with other metals that were between 17.6 and 41.4 times weaker than with Cd2+. In summary, the negative feedback amplifier WCB designed in this work meets the requirements of Cd2+ detection with very high sensitivity and specificity, which also demonstrates that genetic negative feedback amplifiers are excellent tools for improving the performance of WCBs.

Construction of cadmium whole-cell biosensors and circuit amplification

Owing to the prevalence of cadmium contamination and its serious hazards, it is important to establish an efficient and low-cost monitoring technique for the detection of the heavy metal cadmium. In this study, we first designed 30 cadmium whole-cell biosensors (WCBs) using different combinations of detection elements, reporting elements, and the host. The best performing WCB KT-5-R with Pseudomonas putida KT2440 as the host and composed of CadR and mCherry was selected for further analysis and engineering. In order to enhance its sensitivity, a positive feedback amplifier was added or the gene dosage of the reporter gene was increased. The WCB with the T7RNAP amplification module, p2T7RNAPmut-68, had the best performance and improved tolerance to cadmium with a detection limit of 0.01 μM, which is the WHO standard. It also showed excellent specificity toward cadmium when assayed with mixed metal ions. This study demonstrated the power of circuit engineering in WCB design and provided valuable insights for the development of other WCBs. KEY POINTS: • KT-5-R was selected after prescreening and engineered for better performance. • Using multi-copy reporters and the T7RNAP amplifier greatly improved the performance. • p2T7RNAPmut-68 had a detection limit of 0.01 μM and improved tolerance to cadmium.

Colorimetric/fluorescent/Raman trimodal sensing of zinc ions with complexation-mediated Au nanorod

Accurate and selective in-field detection of metal ions in complex media has gained wide interests due to the complexed matrices and weak affinity towards sensing surface. Herein, we develop a first trimodal method for sensing of Zn²⁺ in complex matrices by stimuli-responsive N-[6-piperazinyl-2-pyridinyl]-N-(2-pyridinylmethyl)-2-Pyridinemethanamine dithiocarbamates (DPY) modified gold nanorods (GNRs-DPY). The presence of Zn²⁺ triggers the aggregation of GNRs-DPY, leading to increment of color and fluorescence intensity of the sensing system, which could be visually discerned with bare eye. Moreover, the intensive electromagnetic enhancement among "hot spots" of GNRs, generated during self-aggregation of the GNRs-DPY caused by Zn²⁺, lowers the detection limit of SERS assay to 6 × 10^-3 pM. It is noteworthy that GNRs-DPY based sensing platform not only enables distinguishing Zn²⁺ from Cd²⁺, with simplicity and rapidity, but also demonstrates as trimodal nanoprobe for sensitive and selective quantitative determination of Zn²⁺ in different matrices. Therefore, the GNRs-DPY provides a new strategy for accurate and credible on-spot determination of Zn²⁺ in complicated specimens, as well as offering multiple applications in point-of-care monitoring.

Use of a Polymer Inclusion Membrane and a Chelating Resin for the Flow-Based Sequential Determination of Copper(II) and Zinc(II) in Natural Waters and Soil Leachates

A bi-parametric sequential injection method for the determination of copper(II) and zinc(II) when present together in aqueous samples was developed. This was achieved by using a non-specific colorimetric reagent (4-(2-pyridylazo)resorcinol, PAR) together with two ion-exchange polymeric materials to discriminate between the two metal ions. A polymer inclusion membrane (PIM) and a chelating resin (Chelex 100) were the chosen materials to retain zinc(II) and copper(II), respectively. The influence of the flow system parameters, such as composition of the reagent solutions, flow rates and standard/sample volume, on the method sensitivity were studied. The interference of several common metal ions was assessed, and no significant interferences were observed (<10% signal deviation). The limits of detection were 3.1 and 5.6 µg L⁻¹ for copper(II) and zinc(II), respectively; the dynamic working range was from 10 to 40 µg L⁻¹ for both analytes. The newly developed sequential injection analysis (SIA) system was applied to natural waters and soil leachates, and the results were in agreement with those obtained with the reference procedure.

Cu2+ ion-sensitive surface on graphite electrodes

A new electrochemical interface based on polyacrylic acid (PAAcid) immobilized in a Nafion® polymeric matrix on graphite screen-printed electrodes for detecting copper is presented. The copper is retained in the surface due to the capacity of the polyacid to chelate metals, and quantified using square wave voltammetry. The response was characterized by spectroscopic techniques (UV-vis-IR), which confirmed the chelation from the Cu²⁺ ions by the acid. A calibration curve is presented, showing good linearity and repeatability and its usefulness as a sensor. The range of operation goes from 15 to 50 μM, with a detection limit of 12 μM, making the sensor useful for measurements in environmental samples (after a preconcentration step) and in drinking water.

Electrical detection of trace zinc ions with an extended gate-AlGaN/GaN high electron mobility sensor

In this report, we have developed a high sensitivity zinc ion (Zn2+) detection method based on a Schiff base functionalized extended gate (EG)-AlGaN/GaN high electron mobility (HEMT) sensor. The complexation reaction between the Schiff base and the zinc ions would cause surface potential change on the extended gate, and achieve the purpose of zinc ion detection. Compared with conventional methods, the Schiff base functionalized EG-AlGaN/GaN high electron mobility sensor showed a rapid response (less than 10 seconds) and the limit of detection (LOD) was 1 fM. At the same time, the real-time detection of zinc ion concentration ranging from 1 fM to 1 μM showed good linearity (R2 = 0.9962). These results indicated that it provides a promising real-time detection method for trace-free zinc ion trace detection.

Unconventional application of gold nanoclusters/Zn-MOF composite for fluorescence turn-on sensitive detection of zinc ion

Contrary to organic solvent-induced aggregation of Au nanoclusters (AuNCs), herein, we reported aggregation induced emission enhancement (AIEE) of AuNCs in an aqueous media through confinement of AuNCs by in situ formed Zn-MOF for detecting Zn²⁺. Glutathione capped AuNCs (GSH-AuNCs) was synthesized through reduction of Au³⁺ by glutathione. Zn²⁺ could significantly enhance the fluorescence of GSH-AuNCs upon addition of 2-methylimidazole, which was attributed to the formation of Zn-MOF. XRD and TEM were used to characterize the in situ formed Zn-MOF. Zn²⁺ induced aggregation was demonstrated by dynamic light scattering and TEM. The quantum yields (QYs) of AuNCs after aggregation induced by in situ formed Zn-MOF attained to 36.6%, which was nearly 9 times that of the sole AuNCs. On this basis, a fluorogenic sensor was reported for Zn²⁺ detection with a linear range from 12.3 nM to 24.6 μM and a detection limit of 6 nM (S/N = 3). The proposed sensor was successfully applied to assay the content of zinc in human serum, milk, water, and zinc sulfate syrup oral solution samples. The novel strategy proposed in this work may open a new window of interest in an unconventional application of gold nanoclusters/MOF nanoscale platform for metal ion detection and nutritional assessment of food.

Sequential injection system with in-line solid phase extraction and soil mini-column for determination of zinc and copper in soil leachates

A sequential injection (SI) system equipped with in-line solid phase extraction column and in-line soil mini-column is proposed for determination of zinc and copper in soil leachates. The spectrophotometric determination (560 nm) is based on the reaction of both analytes with 1-(2-Pyridylazo)-2-naphthol (PAN). Zinc is determined after retaining copper on a cationic resin (Chelex100) whereas copper is determined from the difference of the absorbance measured for both analytes, introduced into the system with the use of a different channel, and zinc absorbance. The influence of several potential interferences was studied. Using the developed method, zinc and copper were determined within the concentration ranges of 0.005-0.300 and 0.011-0.200 mg L^-1, and with a relative standard deviation lower than 6.0% and 5.1%, respectively. The detection limits are 1.4 and 3.0 µg/L for determination of zinc and copper, respectively. The developed SI method was verified by the determination of both analytes in synthetic and certified reference materials of water samples, and applied to the determination of the analytes in rain water and soil leachates from laboratory scale soil core column and in-line soil mini-column.

Direct-immersion single-drop microextraction and in-drop stirring microextraction for the determination of nanomolar concentrations of lead using automated Lab-In-Syringe technique

Two operational modes for Lab-In-Syringe automation of direct-immersion single-drop microextraction have been developed and critically compared using lead in drinking water as the model analyte. Dithizone was used in the presence of masking additives as a sensitive chromogenic complexing reagent. The analytical procedure was carried out inside the void of an automatic syringe pump. Normal pump orientation was used to study extraction in a floating drop of a toluene-hexanol mixture. Placing the syringe upside-down allowed the use of a denser-than-water drop of chloroform for the extraction. A magnetic stirring bar was placed inside the syringe for homogenous mixing of the aqueous phase and enabled in-drop stirring in the second configuration while resulting in enhanced extraction efficiency. The use of a syringe as the extraction chamber allowed drop confinement and support by gravitational differences in the syringe inlet. Keeping the stirring rates low, problems related to solvent dispersion such as droplet collection were avoided. With a drop volume of 60 µL, limits of detection of 75 nmol L^-1 and 23 nmol L^-1 were achieved for the floating drop extraction and the in-drop stirring approaches, respectively. Both methods were characterized by repeatability with RSD typically below 5%, quantitative analyte recoveries, and analyte selectivity achieved by interference masking. Operational differences were critically compared. The proposed methods permitted the routine determination of lead in drinking water to be achieved in less than 6 min.

A simple non-extractive green method for the spectrophotometric sequential injection determination of copper(ii) with novel thiazolylazo dyes

A facile sequential method for the determination of copper(ii) in tap and river waters with high sample throughput is proposed.

Integrated ion imprinted polymers-paper composites for selective and sensitive detection of Cd(II) ions

Paper-based sensor is a new alternative technology to develop a portable, low-cost, and rapid analysis system in environmental chemistry. In this study, ion imprinted polymers (IIPs) using cadmium ions as the template were directly grafted on the surface of low-cost print paper based on the reversible addition-fragmentation chain transfer polymerization. It can be applied as a recognition element to selectively capture the target ions in the complex samples. The maximum adsorption capacity of IIPs composites was 155.2mgg^-1 and the imprinted factor was more than 3.0. Then, IIPs-paper platform could be also applied as a detection element for highly selective and sensitive detection of Cd(II) ions without complex sample pretreatment and expensive instrument, due to the selective recognition, formation of dithizone-cadmium complexes and light transmission ability. Under the optimized condition, the linear range was changed from 1 to 100ngmL^-1 and the limit of detection was 0.4ngmL^-1. The results were in good agreement with the classic ICP-MS method. Furthermore, the proposed method can also be developed for detection of other heavy metals by designing of new IIPs.

Automated solid-phase extraction of organic pollutants using melamine–formaldehyde polymer-derived carbon foams

Solid-phase extraction of environmental pollutants is accomplished using carbon foams derived from melamine–formaldehyde polymer foams.