Glassy carbon electrodes modified with reduced graphene oxide-MoS2-poly (3, 4-ethylene dioxythiophene) nanocomposites for the non-enzymatic detection of nitrite in water and milk

Novel aptasensor based on polyaniline functionalized carboxylated dobby carbon nanotubes and molybdenum disulfide for endotoxin detection

Endotoxins, also known as lipopolysaccharides (LPS), are present within the cell walls of Gram-negative bacteria and are released upon cellular death, which can pose a significant risk to human and animal health. Due to the minimal amount of endotoxin required to trigger an inflammatory response in human body, the demand for sensitive methods with low endotoxin detection limits is essential necessary. This paper presents a straightforward aptamer sensor which can enhance the conductivity and specific surface area of molybdenum disulfide (MoS2) by incorporating carboxylated multi-walled carbon nanotubes (MWCNTs-COOH) and polyaniline (PANI). Doping with gold nanoparticles (AuNPs) improves biocompatibility and sensitivity while providing binding sites for thiolated endotoxin-binding aptamers (LBA). This biosensor achieved a remarkable detection limit as low as 0.5 fg mL-1, enabling trace-level identification of LPS. It also exhibits excellent repeatability, selectivity, and stability, facilitating rapid and accurate LPS detection. Moreover, this method demonstrates high recovery rates and specificity for LPS analysis in food samples, showcasing its promising application prospects in trace-level LPS detection within the food industry.

A novel molecularly imprinted electrochemical sensor from poly (3, 4-ethylenedioxythiophene)/chitosan for selective and sensitive detection of levofloxacin

The improper usage of levofloxacin (LEV) endangers both environmental safety and human public health. Therefore, trace analysis and detection of LEV have extraordinary significance. In this paper, a novel molecularly imprinted polymer (MIP) electrochemical sensor was developed for the specific determination of LEV by electrochemical polymerization of o-phenylenediamine (o-PD) using poly(3,4-ethylenedioxythiophene)/chitosan (PEDOT/CS) with a porous structure and rich functional groups as a carrier and LEV as a template molecule. The morphology, structure and properties of the modified materials were analyzed and studied. The result showed that the electron transfer rate and the electroactive strength of the electrode surface are greatly improved by the interconnection of PEDOT and CS. Meanwhile, PEDOT/CS was assembled by imprinting with o-PD through non-covalent bonding, which offered more specific recognition sites and a larger surface area for the detection of LEV and effectively attracted LEV through intermolecular association. Under the optimized conditions, MIP/PEDOT/CS/GCE showed good detection performance for LEV in a wide linear range of 0.0019- 1000 μM, with a limit of detection (LOD, S/N = 3) of 0.4 nM. Furthermore, the sensor has good stability and selectivity, and exhibits excellent capabilities in the microanalysis of various real samples.

Electrochemical sensor based on PEDOT/CNTs-graphene oxide for simultaneous determination of hazardous hydroquinone, catechol, and nitrite in real water samples

Hydroquinone (HQ), catechol (CC) and nitrite (NT) are considered aquatic environmental pollutants. They are highly toxic, harm humans' health, and damage the environment. Thus, in the present work we introduce a simple and efficient electrochemical sensor for determination of HQ, CC, and NT simultaneously in wastewater sample. The sensor is fabricated by modifying the surface of a glassy carbon electrode (GCE) by two successive thin films from poly(3,4-ethylenedioxythiophene) (PEDOT) and a mixture of carbon nanotubes-graphene oxide (CNT-GRO). Under optimized conditions the HQ, CC, and NT are successfully detected simultaneously in wastewater sample with changing their concentrations in the ranges (0.04 → 100 µM), (0.01 → 100 µM) and (0.05 → 120 µM), the detection limits are 8.5 nM, 3.8 nM and 6.1 nM, respectively. Good potential peak separations: 117 mV and 585 mV are obtained between the HQ-CC, and CC-NT. The sensor has an excellent catalytic capability toward the oxidation of HQ, CC, and NT due to good synergism between its composite components: PEDOT, GRO and CNTs. The features of the sensor are large active surface area, good electrical conductivity, perfect storage stability, good reproducibility, anti-interference capability and accepted recovery rate for HQ, CC, and NT determination in wastewater sample.

Electrochemical sensor for sensitive nitrite and sulfite detection in milk based on acid-treated Fe3O4@SiO2 nanoparticles

In this work, a simple electrochemical sensing platform based on acid-treated Fe3O4@SiO2 nanoparticles was successfully prepared for nitrite and sulfite detection. Fe3O4@SiO2 nanoparticles were synthesized through the sol-gel and hydrothermal methods. Fe3O4@SiO2 presented positive charges after acid treatment, which could enhance the electrostatic attraction between Fe3O4@SiO2 and nitrite and sulfite. The Fe3O4@SiO2(acid-treated) modified magnetic glassy carbon electrode (MGCE) was applied to detect nitrite and sulfite using differential pulse voltammetry and cyclic voltammetry. Under optimized conditions, the developed electrochemical sensor presented good analytical properties for nitrite and sulfite detection with detection limits of 3.33 μmol/L and 31.57 μmol/L, respectively. The good recoveries varied from 85.18% to 111.02%, with a relative standard deviation of 0.23-4.80%. Furthermore, the Fe3O4@SiO2(acid-treated) modified MGCE showed better selectivity, reproducibility, and repeatability in nitrite and sulfite detection. Therefore, this proposed electrochemical sensor provides a new method for developing a nitrite and sulfite detection sensor.

Enhancing electrochemical sensing through the use of functionalized graphene composites as nanozymes

Graphene-based nanozymes possess inherent nanomaterial properties that offer not only a simple substitute for enzymes but also a versatile platform capable of bonding with complex biochemical environments. The current review discusses the replacement of enzymes in developing biosensors with nanozymes. Functionalization of graphene-based materials with various nanoparticles can enhance their nanozymatic properties. Graphene oxide functionalization has been shown to yield graphene-based nanozymes that closely mimic several natural enzymes. This review provides an overview of the classification, current state-of-the-art development, synthesis routes, and types of functionalized graphene-based nanozymes for the design of electrochemical sensors. Furthermore, it includes a summary of the application of functionalized graphene-based nanozymes for constructing electrochemical sensors for pollutants, drugs, and various water and food samples. Challenges related to nanozymes as electrocatalytic materials are discussed, along with potential solutions and approaches for addressing these shortcomings.

Application of Polypyrrole-Based Electrochemical Biosensor for the Early Diagnosis of Colorectal Cancer

Although colorectal cancer (CRC) is easy to treat surgically and can be combined with postoperative chemotherapy, its five-year survival rate is still not optimistic. Therefore, developing sensitive, efficient, and compliant detection technology is essential to diagnose CRC at an early stage, providing more opportunities for effective treatment and intervention. Currently, the widely used clinical CRC detection methods include endoscopy, stool examination, imaging modalities, and tumor biomarker detection; among them, blood biomarkers, a noninvasive strategy for CRC screening, have shown significant potential for early diagnosis, prediction, prognosis, and staging of cancer. As shown by recent studies, electrochemical biosensors have attracted extensive attention for the detection of blood biomarkers because of their advantages of being cost-effective and having sound sensitivity, good versatility, high selectivity, and a fast response. Among these, nano-conductive polymer materials, especially the conductive polymer polypyrrole (PPy), have been broadly applied to improve sensing performance due to their excellent electrical properties and the flexibility of their surface properties, as well as their easy preparation and functionalization and good biocompatibility. This review mainly discusses the characteristics of PPy-based biosensors, their synthetic methods, and their application for the detection of CRC biomarkers. Finally, the opportunities and challenges related to the use of PPy-based sensors for diagnosing CRC are also discussed.

Facile Controlled Synthesis of Pd-ZnO Nanostructures for Nitrite Detection

The electrocatalytic characteristics of nanostructures are significantly affected by surface structure. The strict regulation of structural characteristics is highly beneficial for the creation of novel nanocatalysts with enhanced electrocatalytic performance. This work reports a nitrite electrochemical sensor based on novel flower-like Pd-ZnO nanostructures. The Pd-ZnO nanocatalysts were synthesized through a simple hydrothermal method, and their morphology and structure were characterized via field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). Their electrocatalytical performance in the nitrite oxidation reaction was studied via cyclic voltammetry (CV) and the amperometric technique. Compared to pure ZnO and Pd nanoparticles, the Pd-ZnO nanostructures exhibited enhanced electrochemical performance in the nitrite oxidation reaction. In order to investigate the relationships between the structures of Pd-ZnO nanocatalysts and the corresponding electrocatalytic performances, different surface morphologies of Pd-ZnO nanocatalysts were fabricated by altering the solution pH. It was found that the flower-like Pd-ZnO nanostructures possessed larger effective surface areas and faster electron transfer rates, resulting in the highest electrocatalytic performance in the nitrite oxidation reaction. The designed nitrite sensor based on flower-like Pd-ZnO displayed a wide concentration linear range of 1 μM-2350 μM, a low detection limit of 0.2 μM (S/N of 3), and high sensitivity of 151.9 μA mM^-1 cm^-2. Furthermore, the proposed sensor exhibited perfect selectivity, excellent reproducibility, and long-time stability, as well as good performance in real sample detection.

Electrochemical detection of acute renal disease biomarker by Galinstan nanoparticles interfaced to bilayer polymeric structured dirhenium heptoxide film

This work describes a facile fabrication of an efficient electrochemical sensor utilizing sonication-derived Galinstan nanoparticles (Galinstan NPs) interfaced to annealed dirhenium heptoxide (Re₂O₇) thin-film on Silicon (Si) for the quantitative detection of the most promising acute renal disease biomarker Neutrophil Gelatinase Associated Lipocalin (NGAL). Under optimized preconditions, the anti-NGAL antibodies were immobilized on the Galinstan NPs/Re₂O₇/Si electrode by carbodiimide crosslinking to detect NGAL. The composition, morphology, and structural properties of the electrode were elucidated by various physical characterizations. The sensor obtained a high sensitivity (0.018 µA^-1ng^-1ml^-1, R² = 0.99) in differential pulse voltammetry and a minimum detection limit (2.14 ng ml^-1) in electrochemical impedance spectroscopy for a wide range of NGAL concentrations (25-650 ng ml^-1) with high selectivity and stability. The intensified performance of the sensor was achieved by the summed-up electron transfer from the Re₂O₇ film to Galinstan NPs and Galinstan NPs to the electroactive reactants. Additionally, the outer 2D gallium oxide (Ga₂O₃) layer of Galinstan Nps enhanced the redox activities, whereas the metallic core contributed to the magnificent conductivity. The excellent recovery rates of the sensor for different concentrations of NGAL measured in commercial human serum by the standard addition method assured the feasibility of the sensor.

A Highly Sensitive Electrochemical Sensor for Cd2+ Detection Based on Prussian Blue-PEDOT-Loaded Laser-Scribed Graphene-Modified Glassy Carbon Electrode

Heavy metal ion pollution has had a serious influence on human health and the environment. Therefore, the monitoring of heavy metal ions is of great practical significance. In this work, we describe the development of an electrochemical sensor to detect cadmium (Cd2+) using a Prussian blue (PB), poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT)-loaded laser-scribed graphene (LSG) nanocomposite-modified glassy carbon electrode (GCE). In this nanocomposite material, we successfully brought together the advantages of an extraordinarily large surface area. The accumulation of PB nanoparticles results in an efficient electrochemical sensor with high sensitivity and selectivity and fast detection ability, developed for the trace-level detection of Cd2+. Electrochemical features were explored via cyclic voltammetry (CV), whereas the stripping voltammetry behavior of modified electrodes was analyzed by utilizing differential pulse voltammetry. Compared with bare GCE, the LSG/PB-PEDOT/GCE modified electrode greatly increased the anodic stripping peak currents of Cd2+. Under the optimized conditions, the direct and facile detection of Cd2+ was achieved with a wide linear range (1 nM–10 µM) and a low LOD (0.85 nM).

Recent developments on graphene and its derivatives based electrochemical sensors for determinations of food contaminants

The sensing of food contaminants is essential to prevent their adverse health effects on the consumers. Electrochemical sensors are promising in the determination of electroactive analytes including food pollutants, biomolecules etc. Graphene nanomaterials offer many benefits as electrode material in a sensing device. To further improve the analytical performance, doped graphene or derivatives of graphene such as reduced graphene oxide and their nanocomposites were explored as electrode materials. Herein, the advancements in graphene and its derivatives-based electrochemical sensors for analysis of food pollutants were summarized. Determinations of both organic (food colourants, pesticides, drugs, etc.) and inorganic pollutants (metal cations and anions) were considered. The influencing factors including nature of electrode materials and food pollutants, pH, electroactive surface area etc., on the sensing performances of modified electrodes were highlighted. The results of pollutant detection in food samples by the graphene-based electrode have also been outlined. Lastly, conclusions and current challenges in effective real sample detection were presented.

Ice-Templated Large-Scale Preparation of Two-Dimensional Sheets of Conjugated Polymers: Thickness-Independent Flexible Supercapacitance

Two-dimensional (2D) organic materials hold great promise for use in a multitude of contemporary applications due to their outstanding chemical and physical properties. Herein, 2D sheets of poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) are prepared from a commercially available PEDOT:PSS suspension using ice as a template. The 2D PEDOT:PSS sheets grow in the boundaries of ice crystals as the polymers are "squeezed" out of the suspension when the water solidifies. The mechanical robustness of the sheets can be enhanced by incorporating WO₃ nanowires, and the PSS component can be conveniently removed with a concentrated solution of H₂SO₄ to afford stable suspensions of PEDOT or WO₃@PEDOT sheets, either of which can be converted into flexible films with tunable thicknesses via filtration. Swagelok- or pouch-type supercapacitor devices prepared from the WO₃@PEDOT films exhibit outstanding energy-storage characteristics, including high rate capability, thickness-independent energy storage (e.g., 701 mF cm^-2 is achieved with a 1-mm-thick film), high resistance toward mechanical deformation, and good cycling stability. Additionally, a high energy density of 0.083 mWh cm^-2 is measured for a device prepared using a 1-mm-thick film at a high power density of 10 mW cm^-2. The methodology described establishes an efficient and readily scalable approach for accessing 2D organic sheets.

Pd-Cu nanospheres supported on Mo2C for the electrochemical sensing of nitrites

The improper disposal in agricultural and industrial wastewater leads to high NO₂^- concentrations in the aquatic environment, which can cause cancer in humans and animals; thus, their quick and accurate detection is urgently needed to ensure public health and environmental safety. In this study, a reliable and selective electrochemical sensor consisting of Pd-Cu nanospheres (NSs) supported on molybdenum carbide was prepared via simple ultrasonication. Then, a glassy carbon electrode was realized using this composite (Pd-Cu-Mo₂C-modified GCE) to test its electrocatalytic sensing for NO₂^- in a 0.1 M phosphate-buffered solution (PBS) solution via cyclic voltammetry and amperometry; at a low oxidation potential, the anodic peak current of NO₂^- detected by this electrode was significantly higher than that of its unmodified and other modified electrodes. The sensor showed a broad linear response in the 5-165-nM NO₂^- concentration range, with a low detection limit (0.35 nM in 0.1 M PBS) and high sensitivity (3.308 μAnM^-1 cm^-2). Moreover, the fabricated electrode was successfully applied for detecting nitrites in sausages, river water, and milk, showing also good recovery.

Gold nanoparticles decorated bimetallic CuNi-based hollow nanoarchitecture for the enhancement of electrochemical sensing performance of nitrite

Gold nanoparticles (AuNPs) decorated bimetallic CuNi-based hollow nanoarchitecture (CNHN) are reported for the first time as a nonenzymatic sensor for the quantification of nitrite in neutral solution . The CNHN was prepared via a convenient calcining routine using the bimetallic CuNi-MOFs as a coprecursor. The unique chemical structure of hollow CNHN with high specific surface area and abundant terminal amino groups effectively avoid the aggregation of AuNPs and facilitate the subsequent adsorption of nitrite. The Au/CNHN exhibited high electrocatalytic activity towards nitrite oxidation due to the synergetic catalytic effect of AuNPs and CNHN. Chronoamperometric detection of nitrite at the Au/CNHN/GCE achieved a lower linear calibration range of 0.05 to 1.15 mM, with an LOD of 0.017 μM compared with previous reports. The proposed method obtained satisfactory recoveries for nitrite determination in practical applications, which was verified by UV-Vis spectrophotometry. The prepared sensor based on Au/CNHN featured favorable selectivity and stability, which provides a promising approach for real sample analysis. Graphical abstract.

Ultra-Weak Chemiluminescence Enhanced by Cerium-Doped LaF3 Nanoparticles: A Potential Nitrite Analysis Method

In this work, cerium-doped LaF₃ nanoparticles (LaF₃:Ce NPs) were successfully synthesized and characterized. Its chemiluminescence (CL) property was studied, and it was amazingly found that it intensely enhanced the ultra-weak CL of the NaNO₂-H₂O₂ system. The CL mechanism was systematically investigated and suggested to be the recombination of electron-injected and hole-injected LaF₃:Ce NPs. The new CL system was developed to be a facile, original, and direct method for nitrite analysis. Experimental conditions were optimized and then a satisfactory linear relationship between CL intensity and nitrite concentration was obtained. This work introduced a new pathway for the research and application of traditional fluoride NPs doped with RE³⁺.